Search Documents

By M. B. Shirts

Bench-scale studies were made on a reductive hydrometallurgical procedure to convert chalcopyrite flotation concentrate to copper metal or a readily leachable sulfide. Reductive conversion of chalcopyrite and dissolution of iron and sulfur were accomplished in hydrochloric or sulfuric acid solution by the addition of metallic copper, iron, or lead. Use of metallic copper as the reductant enabled extraction of 95 and 46 percent of the iron and sulfur, respectively. The products were ferrous iron, hydrogen sulfide, and a copper sulfide. Use of metallic iron or lead as the reductant enabled extraction of 95 percent of both the iron and sulfur. The products obtained with metallic iron or lead were ferrous iron, hydrogen sulfide, and metallic copper.

Jan 1, 1974

The mechanization of the coal industry in New South Wales involved the introduction of large face and transport machines. The trend is towards still higher capacity units with .greater horsepower and it became apparent that a potential risk of damage to the hearing of workmen existed. In order to assess whether the sound levels were SUfficiently high to impair the hearing of workmen a sound level survey of all major operations in the industry was carried out by the Mining Engineering Division of the Joint Coal Board.The results indicated ·that the operations could be classified into three categories of risk, probably hazardous, of doubtful hazard due to the intermittency of the operations, and of low hazard.Legislation has subsequently been enacted requiring the wearing of hearing preservation aids in some of the probable risk operations.

Jan 1, 1974

By Abdurrahman Cetinbas

The periphery of longwall panels in the Pocahontas No.3 coalbed is characterized by a zone of reduced permeability that inhibits the natural drainage of methane. A residual gas pressure of 105 psig was measured after 1 year in an isolated block of coal measuring 340 by 1,100 feet. The buildup of gas pressure within such large blocks causes methane problems during plowing operations. However, natural drainage holes drilled during development have been found to reduce the gas content of the coal in this coalbed by over 90 percent. The effect of water infusion on dust during plowing operations was investigated using existing methane drainage holes. These holes were cleaned of debris and a pipe was grouted into the hole for water infusion of the panel. Both total and respirable dust levels were reduced by 40 to 79 percent. Water infusion of the panel proved more effective than did the use of a plow-mounted spray system.

Jan 1, 1974

This Part describes a mine pager phone to public telephone interconnect sys tem that permits mine paging telephones to be selectively interconnected with the public telephone system, as illustrated by Figure 1. This interconnect concept was first conceived and demonstrated in breadboard form by H. E. Parkinson of Industrial Hazards and Communications, PMSRC, as one means for providing improved emergency and off-hours communications. The third-generation prototype unit described in this Part was designed and fabricated by Arthur D. Little, Inc. This unit is a small desk-top or wall-mounted unit that connects directly to both the public telephone line and the mine pager phone line, and requires no modifications to either the public dial telephone or mine pager phones. As part of this task, ADL also built, under a very compressed time schedule, a second-generation prototype unit suitable for reliable demonstration of the interconnect concept during the Bureau's technology transfer seminar on mine communications in March 1973. * A major objective of the design of the third-generation unit described in this Part was that it be compatible with present mine pager phone systems utilizing DC voltage on the mine phone line to activate the phone loudspeakers. Therefore, this unit was designed to operate in a push- to-talk, push-to-listen mode that accommodates the inherent design differences and operation modes of the mine phones of different manufacturers. Though this push- to- talk, push- to-listen mode of operation may seem slightly unusual at first sight, we have found it is easily learned by new users. However, mine phone manufacturers wishing to expand their product lines with such an interconnect system will probably find it to their advantage to customize the design of this system to their particular mine phones, thereby utilizing the unique attributes offered by their individual product lines. This customization should not be difficult, and Section III below suggests some of the features that can be easily added to future designs. Detailed parts lists and circuit schematics for the present third-generation proto- type system can be obtained from the system manual submitted to PMSRC and placed on public file.

Jan 1, 1974

By J. J. Scott

Friction Rock Stabilizers, trade name Split Set*, is a new support system invented by the author and under development by Ingersoll-Rand and Lee-Norse Company. Split Sets are a substitute for standard bolts or fully grouted resin bolts and have certain advantages which are: 1. Improved safety for the miner 2. A rational design is possible based on rock mechanics principles 3. Supports can be made either to be yieldable or rigid 4. Supports can be used to build a roof beam or to suspend roof material 5. It is cheaper than the resin system and costs about the same as standard bolts.

Jan 1, 1974

By H. J. Lechtenberg

This Bureau of Mines report investigates solvent injection as a means of increasing oil production from low-gravity oilfields; thus, wells in two California oilfields that produce from reservoirs having low-gravity oil were injected with highly aromatic solvents to increase their oil recovery. The wells were either allowed to soak or the solvent was circulated for a period of time. In some of the wells, the solvent was followed by a slug of water. The post-stimulation production rate was considerably higher than the prestimulation rate of the wells. Wells in which the solvent was not followed by water showed an immediate increase in oil production, and essentially all of the solvent was recovered. The wells in which solvent was followed by water essentially showed a delay in the increase in oil production, thus indicating a temporary water block. The results show that the production rate is usually increased by the injection of solvent, and the method may prevent early abandonment of marginal producers. Cumulative post-stimulation oil production indicates that cyclic solvent injection treatment can be an economic success.

Jan 1, 1974

By Charles R. Marek

There is an ever-increasing need for quality construction materials to provide the necessary housing and transportation facilities required for the protection and movement of people and goods. By the year 2000, requirements for housing in the United States will have doubled due to population growth. Requirements for transportation facilities in this same period will also have increased substantially. Further, all existing facilities for both housing and transportation will require substantial maintenance of one form or another. Aggregate is the basic material of the construction industry. There is some occurrence of aggregate source material in virtually every state of the United States, and in every country in the world. United States reserves of commercially useable aggregate have never been systematically estimated and are probably so vast as to be incalculable.1 However, in many areas its existence is largely negated by inaccessibility. Often it is lodged deeply or intricately in the earth or it is too distant from markets to offer a desirable "return on investment" under the present economic structure. Other factors that prevent its utility are the occurrence of small scattered deposits that individually are too small to justify the necessary capital investment for exploitation and collectively are too widely disseminated; also, the aggregate nay be deficient in certain desired chemical or physical qualitites.1

Jan 1, 1974

By W. L. Dare

Land use planning is not a new concept in the United States but the emphasis has changed drastically since the early 1960's. Under the old interpretation we tried to expand our frontiers and develop our land, but as society has become more affluent and mobile the demand has grown to preserve those parts remaining undeveloped. There is something of a paradox inherent in this change of emphasis. While affluence has motivated our support to preserve the quality of the natural environment, industrial development is needed to support the affluence. Because we cannot accomplish all of each, sound planning and compromise will be necessary since it is unlikely that, the American people will want to surrender much of their life-style or their awakening environmental concern. Any industrial society, whether a goal reached or an aim yet ahead, is built largely on the use of mineral raw materials and energy, the physical base of nearly all activities and products. The standard of living which is important to us all is growing more dependent upon these minerals, metals, and energy fuels. Although reduction in consumption of raw materials may be acceptable to those at a certain economic level of a society, those who have not reached that level cannot be expected to accept a lowering of their present or anticipated standard of living.

Jan 1, 1974

By R. L. Curfman

From January 1, 1965 through July 5, 1970, the very difficult potash ore body of Texasgulf Inc. near Moab, Utah was mined by conventional methods. The mine was gassy, the temperature was high and structural conditions precluded a satisfactory or economical extraction ratio due to the undulating configuration of the ore horizon. In 1966, 67, and 68, alternative mining methods were considered, among which was solution mining of the ore body. Cost studies indicated that the use of crystallizers to evaporate the large amounts of water attendant to solution mining offered no chance of economic success. In 1969 additional testwork and cost studies were carried out utilizing solar evaporation. These studies showed economic potential and justified additional investigation. As a result of these studies, Texasgulf now gathers potash solids from these solar evaporation ponds, (Fig. l), after pumping them from the underground mine as brine. The investigations were concentrated in four basic areas : (1) area evaporation rates and crystal growth habits; (2) underground solution tests including heat transfer rates; (3) accelerated evaporation tests to provide material for metallurgical testing, and (4) tests of evaporation pond lining materials and application techniques, along with area surveys to ascertain if sufficient earth was available in the near vicinity to con-

Jan 1, 1974

By Russell E. Griffin

Dielectric constants and dissipation factors were measured by the Bureau of Mines for 13 simulated lunar rocks over the 20-to 100-megahertz frequency range by means of the susceptance-variation method. Measurements were made at room temperature and normal atmospheric pressure. Results are presented and some comparison is made with data reported by others. The rocks used include a broad range of physical characteristics and chemical compositions from the large areas of volcanism in Oregon and northern California, and two nonvolcanic types. These rocks make up a suite of rock standards used by a group of laboratories engaged in lunar research. The data presented will add to the basic scientific and engineering knowledge needed to utilize extra-terrestrial mineral resources for support of future space missions.

Jan 1, 1974

By Frank Pilotte

Proper design characteristics for a seismic system to locate miners during a mine disaster are considered in terms of a total system concept. Field hardware, processing equipment, operating personnel, deployment, training, and supportive R and D are necessary elements of the total system. Each of these elements is discussed and an indication given as to the requirements necessitated by each one. Hardware must be portable, rugged, and fieldworthy. Processing equipment must be simple to operate, expandable for future processing improvements, and ruggedized for field use. A small well-trained team must be available for quick response in times of emergency. Alternative deployment procedures are necessary to allow for a variety of situations including both ground and air delivery. Supportive R and D is used to support training and upgrading of the system.

Jan 1, 1974

By Richard L. Sanford

The generalized rail haulage simulator described in this paper is an outgrowth of the need to expand a previously developed single level simulator to permit analysis of production problems where intermediate car storage is used. Many of the ideas of the former single level simulator, which is an integral part of an Underground Generalized Materials Handling Simulator (UGMHS), have been used in model development. In addition, experience gained in applying the earlier model to a variety of operating conditions has been heavily relied on. The generalized rail haulage simulation model can operate as an independent system and, as such, can be used to analyze rail haulage systems using production distributions as data input. In addition, this model is designed to replace the present rail haulage sub-assembly in the UGMHS model and the linking procedure has been integrated into the model. The flow of coal from production sections in UGMHS, for example, fill the mine cars and a condition of no empty cars at a loading station will shut down in by production systems.

Jan 1, 1974

By Charles H. Ricker

Simulation models have been widely used to analyze the operations and characteristics of a variety of systems. Such models mimmick a projected reality by analyzing the interaction of the events, transactions, and facilities which combine to make up the system. The models are structured as a computer representation of the system components and their logical, precedence and timing relationships. The operation of the system is then simulated over some finite time interval to gather analytical and staistical data. This paper presents a method whereby bulk handling systems, either actual or proposed, may be analyzed by means of simulation models to project the enconomic consequences which may be expected from the system over some future time interval. An example is given to illustrate the construction of bulk handling simulation models, the derivation of performance data, and the analysis of the information with an eye to effective decision making.

Jan 1, 1974

By G. W. Eiger

Bureau of Mines laboratory tests show that ilmenite concentrates with titanium dioxide contents as low as 33 wt--pct can be beneficiated to produce a crystalline substitute for natural rutile suitable for direct chlorination. The synthesized product prepared by a three-step procedure was comparable with natural rutile in titanium content. Reduction smelting of ilmenite removes iron as a pig iron byproduct, and the remaining slag phase is greatly enriched in titanium. Oxidation of the slag in the presence of phosphorus¬bearing slag additive converts the titanium-bearing phases to discrete rutile crystals and a glass phase containing most of the associated impurities. Rutile is separated from the glassy impurities by attrition scrubbing ground slag in dilute phosphoric or sulfuric acid solutions. Tests made in a laboratory fluid-bed reactor show that synthetic rutile responds to chlorination at the same rate as natural rutile and that more than 95 pct of the titanium contained in the feedstock was extracted as titanium tetrachloride.

Jan 1, 1974

By Hsu-Hui Hsing

In several previous studies from this laboratory (1-4) the autophobicity concept of Zisman and co-workers (5, 6) has been extended to gas phase adsorption processes. Low molecular weight alcohols adsorb on silica or alumina to yield novel isotherms in that monolayer adsorption occurs at low relative pressures indicative of strong bonding, but subsequently multilayer adsorption is quite sparse and diminishes with molecular weight of the alcohol. Such isotherms fit no standard classification scheme, however, in the vacinity of monolayer coverage alcohol isotherms give an excellent fit to the Langmuir or B. E. T. , Type I model (7). Monolayer adsorption is relatively irreversible and it is thus possible to prepare these chemisorbed layers and perform subsequent adsorption studies thereon. All indications are that the adsorptive properties on such films is radically different from that on the underlying alumina (4, 8) and in one study finite contact angles for hydrocarbon fluids were observed. One perennial conceptual difficulty is that there is no observed upper bound to the adsorption isotherm which would be necessary for autophobic adsorption to occur. The cause for this has been studied, and it is currently believed that adsorption is complicated by reversible capillary condensation at contact points between powder particles. The evidence for this is that large particle powders give less "apparent" adsorption at high relative pressures and in one very tedious study adsorption on planar sheets, oxidized aluminum displayed similar reduced uptake at high relative pressures when compared with high specific surface area powders (3).

Jan 1, 1974

By Clyde L. Smith

Since the early 1950's exploration in the Yukon Territory, Canada, has been confined largely to Selwyn basin where at least five large stratiform or massive sulfide Pb-Zn deposits have been discovered. The five ore bodies total nearly 100 million tons of 10-16% combined Pb-Zn with 1-3 oz./ton Ag. The only deposit currently in production is the Anvil Mine operating at 8,000 tons per day. Beginning in 1972, exploration in the Mackenzie Mountains, east of Selwyn basin and west of Mackenzie arch, resulted in finds of Mississippi Valley type Zn-Pb mineralization in a belt of Proterozoic and Lower Paleozoic carbonate rocks (Figure 1). Four districts have been located and intensive exploration by numerous Canadian and Arnerican mining companies is currently in progress over a length of 400 miles in the carbonate belt. The consensus is that a major new Zn-Pb province may be taking shape.

Jan 1, 1974

By Robert K. Towner, Francis S. Kendorski

Shotcrete drift linings at the Climax Mine of the Climax Molybdenum Company have undergone four years of extensive evaluations as a replacement for thick poured-in-place concrete linings. Any drift lining at Climax must be able to withstand the rigors of undercut and secondary blasting, weight problems induced by panel caving, and the abrasion of slusher mining. Examined here are the conclusions reached so far on shotcrete drift linings which have not yet completed the approximately six-year cycle from development to ore exhaustion. Properly applied shotcrete is an adequate drift lining for all phases of the Climax panel caving system of mining. Undercut blasting will damage shotcrete unless blasts are correctly timed. Weight problems will destroy shotcrete drift linings as efficiently as it will destroy concrete or steel support systems. Abrasion and secondary blasting results are inconclusive as the shotcrete lined slusher drifts have not entered the ore production stage of the mining cycle. In addition to drift linings, Climax has found shotcrete to be invaluable for lining large underground shops, for temporary support systems, for permanent ventilation bulkheads and for the repair of abraded or weight damage concrete lined slusher and haulage drifts.

Jan 1, 1974

A Helix Pressure Gauge to Indicate roof bolt loads was designed, fabricated and field tested. The gauge indicated loads between 3,000 and 15,000 pounds with a ± ten per cent error. The coat of fabrication of the gauge was estimated to be $3.39 including an assumed overhead and profit per indicator for a series production of 5,000 unite. The unit can be read on a bolt to within ± 1,000 pounds load from a distance of twenty feet.

Jan 1, 1974

By Ulises Deveze T.

The coal company Minerales Monclova, S.A. (MIMOSA), the owner of the Mimosa R Line, is a subsidiary company of Altos Hornos de Mexico, S.A., the largest steel plant in Mexico with an annual capacity of 2.5 million metric tons of steel ingots. The raw material's which are used in the steel plant are provided by the following companies: La Perla Minas de Fierro, S.A., iron ore; Cia. Minera de Guadalupe, S.A., Cia. Carbonera La Sauceda, S.A. Cia. Minera La Florida, S.A., and Minerales Monclova, S.A., which provide the coal used for coke, and altogether constitute the industrial group AHMSA. The coal property of Minerales Monclova, S.A. is located in the Sabinas coal area in the northwestern part of the Sabinas basin.

Jan 1, 1974

By R. Blickensderfer

Test equipment that simulated frictional impacts between coal-cutter bits and mineral inclusions at a coal face during operation of a continuous coal mining machine was used by the Bureau of Mines in the laboratory to study the incendivity of impacts between various rocks, metals, and hard-metal alloys in an explosive mixture of air-7 pct natural gas. Quartzitic sandstone was found to be the most incendive of several rocks tested. Limestone concretions from a coal seam, known locally as "sulfur balls," sparked furiously but were not incendive. Among the metals tested, the type of steel used in commercial coal-cutter tools was the most incendive material tested. A l7-4PH stainless steel was less incendive and appears to be the most promising high-strength steel alloy, reasonably economical, for use in coal-cutter bits. Some hard-metal alloys, primarily titanium and zirconium diboride composites, were also evaluated as possible replacements for the conventional cobalt-bonded tungsten carbide used in the tip of coal-cutter bits. The metal-bonded diborides were generally less inc endive but more brittle than the conventional tungsten carbide. Carbonitride coatings on tool bits were also tested but found to have no advantage. The source of ignition during frictional impact between metal and rock was studied. Immediately after impact, a yellow flash was observed and a smear of metal near its melting point occurred on the rock. This hotspot on the rock, rather than the yellow flash or sparks or metal fragments, was observed to be the cause of the ignition.

Jan 1, 1974