Search Documents

By Charles F. Herbert

In February of this year at the Washington, D.C., hearings of the Interior Department on the Alaska pipeline, the author was amazed to hear speaker after speaker oppose not only pipline construction but any development whatsoever in the State of Alaska. In one case, a man objected to development in Alaska because his neighbor in Maryland had cut down some shade trees. Another man recited at length from the poems of Robert W. Service. While it seemed inconceivable that such thoughtless opposition should have any effect, a check with the offices of some congressmen showed that mail was largely against any development of Alaska. In the barrage of words and redundant phrases directed against Alaska, it is difficult to find a thought worthy of study. Fortunately, there is a statutory guide towards resolution of the problem of development versus non- development. This law, the Environ- mental Protection Act of 1969, has indeed given much of industry the jitters; copper smelters see no way to comply with the new sulfur- emission standards, the Alaska Department of Highways estimates that the Act has nearly doubled the cost of planning and engineering for highway construction. In spite of these and many other troubles and costs, the Act provides a sound legal basis for defeating nihilistic emotions and, since Alaska is relatively undeveloped, adoption of environmental safeguards will be simpler than correcting longstanding abuses.

Jan 1, 1971

By E. J. White

Data from oil well logs and core analyses were used to quantitatively evaluate formation porosity and water saturation of heterogeneous carbonates and to study the pore geometry and performance characteristics of cores from these formations. Logs and cores from the Madison limestone from 233 wells in three fields in the Williston basin were used in the investigation. A comparison of log and core analyses shows that log porosities are consistently larger than core porosities, and the differences are correlatable with core porosity ranges. Water saturations from logs are usually smaller than the corresponding core saturations by summation of fluids, but the difference is attributable to mud filtrate invasion into the cores during drilling. Petrophysical studies show that the low permeabilities and high residual water saturations in these reservoir rocks are due to their fine crystalline texture and complex pore geometry (heterogeneity). It is concluded that both log and core analyses must be used for reliable evaluation of these carbonate formations.

Jan 1, 1971

By Roberto L. Romero

The dressing of Bolivian tin ores has been done up to the present by classical. gravity methods, taking advantage of the high specific gravity of cassiterite compared with that of the accompanying gangue. For this purpose, jigs and shaking tables are used in the treatment of the various size fractions in which the ore is classified. Bolivian ores are mainly of the vein type and, to obtain a reasonable separation, crushing and several stages of grinding are necessary during the process to substantially liberate the cassiterite from the gangue. Gravity processes for cassiterite are effective for sizes down to 200 mesh. Below this size the efficiency of the gravity methods falls off very rapidly with increasing fineness of the mineral grains. The conventional treatment for this material is desliming followed by tabling on shaking tables various other types of machines have been designed for the gravity treatment of these fine particles but they have had limited success. Bolivian ores contain an appreciable amount of minus 200 mesh material constituted by "primary fines" caning from the mine itself, and "secondary fines" originated during the crushing and grinding necessary for liberation of the difficulty in the treatment of these fine particles is one of the causes why the recovery of tin in concentrates is only of around 50% in the mines owned by Corporacidn Minera de Bolivia, the State owned enterprise. The average figure for other Bolivian mines is

Jan 1, 1971

The metallurgical works of the Electrolytic Zinc Company is situated on the Derwent Estuary, approximately five miles north of the city of Hobart and near a relatively dense housing area. Zinc concentrates, consisting chiefly of zinc and sulphur, have been roasted at Risdon for 53 years;- recently at rates of 1, 100 tons per day. The zinc content of the ores is converted to zinc calcine (ZnO), which is a dusty material. The calcine is leached with acid to form zinc sulphate, which is then electrolysed to make zinc. The sulphur is oxidised during roasting to sulphur dioxide, part of which is converted to sulphuric acid and part is dissolved in estuarine water which is then discharged to the Derwent Estuary. Photographic slides were exhibited showing the unaffected green flora of the nearby hills, of clear exit stacks, of green lawns, and of a w ll lrcnt nines hnlP anlf nniir.qa within the Wnrka hnnnrla_rv_

Jan 1, 1971

By A. Leppala

Scope of the Courier 300 System The fact that reliable on-stream analysis is a prerequisite for effective flotation control is hardly disputed today. Nevertheless, up to now no system has been available that includes all the equipment necessary for successful analysis. However essential an on-stream analyser is in itself, reliable and accurate assaying can only be assured after techniques for sampling, handling the slurries and computing the X-ray data have been developed for the purpose. The Outokumpu Company's Courier 300 System is a complete package that can be installed and handed over with the key. It includes the equipment needed for sampling and handling the slurries. It has been developed from the start to meet industrial demands. Obviously an on-line system must comply with far stricter standards than one designed for a laboratory. Assays are computed by an Outokumpu 316 digital data processor, which is an integral part of the system and controls its entire performance. The computer software is programmed as a standard package, including a highly advanced new model for assay computation. Analysis output is available for a process computer, report typewriter:, and recorders. The package also includes calibration for slurry assays at our pilot installation before delivery. A complete Courier System can analyse up to 4Z slurries and six elements in each slurry. Thanks to its modular design, it can be dimensioned initially to the customer's requirements and is easy to expand later at low cost. Being a mining company itself, Outokumpu has been able to utilize its own long experience in non-ferrous metallurgy - an important factor contributing to the success of the Courier system. History of the project and present installations The first on-stream analyser was installed at Outokumpu'a Pyhasalmi Con¬centrator at the end of 1967, after several years' development. Since then,

Jan 1, 1971

By Foster Fraas

Calculations based on data related to the electrostatic precipitator illustrate the variation in the electric forces on a particle with change in position in the ionized field. The feeble forces in some separators are explained by the low field intensity at midpoint locations between the electrodes. When the particles are in contact with the exterior surface of a rotating cylindrical electrode, a high field intensity at the electrode surface combined with the image charge results in large electric forces. The permissible feed velocity increases as the square root of the electrode diameter, providing high values in efficiency and feed rate capacity, particularly in surface-to-mass ratio separations such as are encountered in secondary materials recycling operations.

Jan 1, 1971

By R. Walker

This paper deals with the selection and design of a belt conveyor handling steam coal between a mine and a barge loading terminal, and extending for some 5 ¼ miles over some of the most rugged terrain in the state of West Virginia, U.S.A. After a thorough analysis by consulting engineers and the owner's engineers, a single-flight cablebelt conveyor was chosen as representing the alternative of greatest reliability and lowest over-all cost. The value analysis and design features of the system are covered in this paper along with an updated report on the performance of the system since its start-up in the spring of 1969.

Jan 1, 1971

By Warren B. Davis

Introduction If a subject this broad were to be covered in even moderate detail, it would require a set of books about the size of an encyclopedia. Since an acceptable length for this paper is a small fraction of one book, it will have to consist of a few samples of the subjects that I think are the most pertinent to World Fossil Fuel Economics. I plan to discuss the trends in world energy demand, particularly in the U. S. and Europe; the consumption patterns and cost patterns of oil, gas and coal; the prospects of synthetics; and some of the effects of government regulation of fuel economics. World Energy Demands Fig. 1 shows Free World energy consumption by principal areas for the period from 1950 to 1970 and a forecast for the period from 1970 to 1985. These figures include only the measurable forms of energy. An example of energy consumption that is not measured is the wood a peasant might cut in the forest and bum in a fireplace to heat his home. This omission probably is a very small part of the total. This forecast is not identical with that of Wayne E. Glenn (see Page 22), but the differences in total energy consumption are not significant. The U. S. consumption, which was 55 percent of the world total in 1950, had declined to 45 percent by 1970, and is expected to decline further to 38 percent by 1985. Western Europe has consumed 28 percent of the total from 1950 to 1970 and is expected to lose share slightly between 1970 and 1985. The most spectacular gainer is Japan, which increased consumption from 2.5 percent in 1950 to 7.5 percent in 1970, and is expected to reach nearly 17 percent by 1985. The over-all Free World total has grown from 62 quadrillion Btu (equivalent to 29 million B/D of crude oil) in 1950 to 151 quadrillion by 1970, an average growth rate of 4.5 percent/year. This total is expected to grow at a rate of 5 percent/year between now and 1985, reaching 315 quadrillion Btu (equivalent to nearly 150 million B/D). Fig. 2 shows which fuels supplied this energy between 1950 and 1970, and gives an estimate of how it will be supplied between 1970 and 1985.

Jan 1, 1971

By Benton L. Tibbetts

Comprehensive geophysical measurements were made in the Tertiary Channel gravel deposits of Badger Hill, Calif., with the refraction seismograph, gravimeter, and well logging equipment, to develop a three-dimensional physical model of the gold-bearing gravels. Tests were also made of the applicability of magnetometer and electrical resistivity techniques. Results of 14 seismic profiles revealed four distinct layers with velocities of 1,600 ft/sec for loose gravel, 5,900 ft/sec for compact gravel, 8,600 ft/sec for cemented, blue gravel, and 15,500 ft/sec for bedrock. The depth to bedrock along the middle of the channel varied from a minimum of 100 feet in the hydraulically mined pit area to a maximum of about 300 feet in the upper bench area immediately south of the pit. These geophysical methods revealed that 40 percent of the drill holes necessary to delineate the deposit could be eliminated, at a cost saving of at least 30 percent.

Jan 1, 1971

By Thomas L. Craig

The Wellman-Lord SO2 Recovery Process is operating commercially at one location in this country and at two locations in Japan. Tail gases from a sulfuric acid plant, from an oil fired steam generator and from a sulfur recovery unit are the respective applications. 1) At the Olin Corporation's Paulsboro, New Jersey, stack gas from a spent acid regenerative sulfuric acid plant-45000 SCFM - is treated in the W-L unit to reduce sulfur dioxide concentrations from 4500 ppm to less than 500 ppm. 2) At the Japan Synthetic Rubber plant in Chiba Prefecture, stack gas from an oil-fired steam generating plant - 120,000 SUM - is reduced from 2100 ppm S02 to less than 200 ppm. 3) At the Toa Nenryo Kogyo refinery in Kanagawa Prefecture, tail gas from a sulfur recovery (Claus) unit - 41,000 SUM - with, an inlet SO2 concentration of up to 13000 ppm is reduced to less than 200 ppm. The three installations are operating successfully and are capable of reducing S02 emissions to levels significantly below the concentration guaranteed. With the one exception of a higher than guaranteed chemical make up requirement at Paulsboro, utility and chemical requirements will be less than design.

Jan 1, 1971

By M. D. Schlesinger

Mercury exists in coal at very low levels; the structure of coal, the vapor pressure of mercury, and its almost universal occurrence introduce unusual problems into the analytical methods. Round-robin analyses by several laboratories, each using its own techniques, indicate that the average mercury content of coal is about 0.2 part per million. Some western coals are as low as 0.05 ppm.

Jan 1, 1971

By John C. Cook

A 1-year program of exploratory research, to determine the feasibility of radar exploration in advance of coal mining, has been completed. Advance detection of obstructions including faults, clay veins, abandoned wells, and pyritic concretions would improve the safety and efficiency of mining. Initial calculations based on laboratory tests of the RF electrical properties of bituminous coals indicated feasibility; radar waves at frequencies below 100 MHz should be detectable through tens to hundreds of meters of coal and be well-reflected by clay, pyrite and metal obstructions. Using a proprietary, experimental, VHF short-pulse "mining radar" system, two cycles of field testing and equipment improvement were completed. Measurements were made in three bituminous coal mines, a quarry, and a salt mine. Comparisons were made with ground-penetrating radar equipment developed by others for salt dome exploration and for military tunnel detection. The proprietary mining radar equipment and techniques used were found to be the most effective known for coal exploration, but further improvements are needed; one major problem in all systems is interfering clutter signals arising in the equipment and from mine room reverberations through leakage coupling of the antennas to the air. Nevertheless, several practical goals have been achieved: excellent radar reflections were received and identified through up to 30 feet of coal; reflections from a wet, abandoned drill hole were identified by their polarization property and detected at distances up to 272 feet, and mine-wall reflections were detected at distances up to 735 feet (both through salt); propagation through and reflections from large vertical clay veins in coal were demonstrated; experimental results agree reasonably well with theory. The results and experience gained during the project affirm the feasibility of the method. They also provide a firm basis for the development of a practical radar technology for exploration in advance of mining. No Subject Inventions, as defined in the contract, were made in the course of this work.

Jan 1, 1971

By R. D. Brown

The Federal Government's White Paper on Tax Reform received further major criticism in the reports of the Committees of the House of Commons and the Senate, which recently completed a lengthy review including public hearings of the government's proposals. These reports both criticized the emphasis placed by the White Paper on its concept of tax equity rather than on a system which would promote economic growth. However, the Finance Committee of the House of Commons was prepared to accept, with modifications, a number of the White Paper's key reform proposals. The Senate Finance Committee was more critical of the basic thrust of the tax reform program and recommended that a modification of the existing tax system would be more appropriate to Canada's needs. Both Committees re-commended a more favourable treatment of mining income than that originally proposed in the White Paper, and to some extent both Committees suggested proposals that were even more favourable to the industry than those set out in Finance Minister Benson's amended proposals made in August of this year. This article out-lines the principal recommendations and comments in the reports of both the House of Commons Committee and the Senate Finance Committee.

Jan 1, 1971

By S. C. Schaefer

Thermodynamic properties of indium oxide (In203) have been studied with a high-temperature galvanic cell employing stabilized zirconia electrolytes. In the temperature range 790° to 1,230° K the free-energy change for the cell reaction 21n(1) + 3Cu20(c) = In203(c) + 6Cu(c) together with the standard free energy of formation of cuprous oxide gives the standard free energy of formation of indium oxide from the elements as ?Gf° = -218.78 + 75.34 X 10-3T ±0.7 kcal/mole. A third-law analysis yields the standard enthalpy of formation: ?Hf°298.15 = -221.5 kcal/mole.

Jan 1, 1971

This volume constitutes the final report for the Rescue Subsystem portion of the Coal Mine Rescue and Survival System program conducted by the Westinghouse Electric Corporation under contract to the United States Bureau of Mines (Contract Number H0101262 dated Jung 17, 1970). The program was directed by the Special Systems Department of the Westinghouse, Baltimore, Maryland facility. The basic objectives of the CMRSS program were to develop and test hardware to determine the efficacy of a variety of coal mine rescue and survival concepts and techniques. These concepts were drawn from two major- sources: the Request for Proposal from the Bureau of Mines and the final report on the Mine Rescue and Survival Study conducted by the National Academy of Engineering (NAE).

Jan 1, 1971

By Jan D. Miller

Under the name given to this column, I almost feel obliged to write about some aspect of grinding, but I have decided instead to comment on the future of chemical processing. In recent years, I have seen a tremendous interest in extractive metallurgy develop among undergraduate and graduate students at the University of Utah. For example, of the 12 graduating seniors this year, over half seem to prefer extractive metallurgy to physical metallurgy. In particular, they seem to be most interested in hydrometallurgy, or chemical processing, obtaining industrial exposure to the phenomena they study via part-time employment at the Kennecott Research Center and the USBM Metallurgical Center in Salt Lake City. The stimulus has been generated by society itself. Many students are dedicated to the proposition that new technology can circumvent the destruction of our environment, a concept which provides considerable motivation. At the governmental level, the recent concern for the quality of our environment has created action in the area of chemical processing both through imposition of stringent air and water quality standards, and through increased funding for technological research in this area. The National Academy of Sciences (NAS) gave impetus to this movement when it pointed up the need for development and support of such disciplines as extractive metallurgy, particularly chemical processing, in a recent report on Mineral Science and Technology. The recommendations in the NAS report have prompted governmental action on many fronts, including the Bureau of Mines, and have also given rise to direct legislation in the form of two bills -H. R. 3492 and S. 635- presently before Congress to a mineral engineering education. The report recommends that chemical processing technology (more generally extractive metallurgy) be developed by both new engineering techniques and unconventional chemical techniques such as application of the chemistry of nonaqueous liquids to mineral systems.

Jan 1, 1971

By Ian McC. Stewart

"Seam gas flow in coal mines takes place through a medium which has both capacity and resistance and can therefore be expressed in terms of the basic diffusion equation, provided that the characteristics of the system can be adequately described. It may be possible to lump the variations from point to point in a seam together as an effective diffusivity. The paper discusses the characteristic flow-time patterns for various types of openings and the particular features of coal and seam which influence the diffusivity.Two field experiments are described in which gas make to a heading and to a borehole were measured in a mine for which considerable data on coal sorption properties were available. Incremental gas flow measured from the borehole experiment predicted the actual flow from the heading measurements remarkably well. The effective permeability adjacent to the face was much higher than expected from the properties of the coal. The incremental flow measurements to a horizontal (in-seam) borehole showed a striking picture of advancing 'relaxation' behind the face which is not discernible by other experimental means."

Jan 1, 1971

The Bureau of Mines is the engineering arm of the Government for mineral resources. Its mission is to carry out laboratory and field studies that will assure the wise and effective development and use of our Nation's minerals, fuels, and underground domain in order to preserve the security and enhance the welfare of our people. Specifically, studies are directed to the means by which current and emerging demands may be met, the real cost of such achievements, and the assessment of related social and economic factors. Ways are sought to fulfill our material needs in a manner that minimizes occupational hazards to workers in the industry, reduces waste, and ensures that mineral raw materials are supplied and mineral-based products are used and are disposed of efficiently, without objectionable social and environmental costs. The headquarters of the Bureau of Mines is located in Washington, D.C. The Bureau's research and development program, however, is conducted at 19 research centers and laboratories located throughout the United States.

Jan 1, 1971

By A. W. Hamilton

If you don't know a gauss from a grasshopper, you may be better off than you, think, particularly if you're an ore dressing engineer charged with the responsibility of selecting magnetic equipment for minerals separation and beneficiation. Gauss is a unit of measure for a magnetic field. It indicates the number of imaginary lines of force per square centimeter or per square inch radiating from a magnet. In discussing the strength characteristics of a magnet, we have come to speak of a magnetic field of 800 gauss, for example, meaning 800 lines of force per square centimeter. Gauss became the standard for selecting drum type separators many years ago under an arbitrary set of circumstances. The standard has continued to this day even though magnetics applications engineers have long considered it inadequate. The configurations of the older gauss meter were such that the most accurate and convenient readings on a drum type separator could be made at distances greater than one inch. So, an arbitrary distance of two inches was established and that two inches became the standard. Since then, it has become commonplace to specify magnetic strengths for drum separators according to average gauss readings at two inches; for example 500 gauss average at two inches, 750 gauss average at two inches and so on, even though gauss readings at two inches have much less to do with the separating and beneficiating function of a given application than was formerly believed. The standard was adopted as a means of gauging the strengths of electromagnetic drum type separators, for they were the only ones around at the time. These machines were usually designed with no magnetic considerations other than that the material to be separated should be agitated vigorously and the magnetic fields should be deep and strong. Drums built this way performed well enough, so it seemed logical to measure their magnetic strengths. Hence, gauss at two inches. Now, new improvements in magnetic techniques have made average gauss measurements at 2 inches positively obsolete.

Jan 1, 1971

By Jacob N. Frank

A factorially designed, hydraulic fragmentation experiment using a high-pressure water jet was conducted on concrete blocks. Three levels of pressure, standoff distance, and impact angle and two levels of traverse time and surface condition were used. Three variables were measured: depth of penetration, volume of material removed, and width of slot. Three stepwise linear regression equations were developed from the jet parameters and the physical properties of the concrete. The three basic equations, describing the significant jet parameters and physical properties, were developed into 15 predictor equations, five for each variable investigated. Direct regression equations were also developed for each variable investigated to show the result of increasing or decreasing each significant variable. Energy efficiencies were developed for the experiment and for each significant factorial variable.

Jan 1, 1971