Search Documents

By Sven Petersen, Iain J. Stobbs, Bramley J. Murton, Paul A. J. Lusty

"INTRODUCTIONIt is widely thought that seafloor massive sulphide (SMS) deposits, the modern analogue of volcanogenic massive sulphide (VMS) deposits, present a potential global resource for base (Cu, Zn) and precious metals (Au, Ag). In addition, SMS deposits can be enriched in ‘critical metals’ including Se, Te, Tl [1], which are essential for use in the construction of modern and green technologies. Globally over 340 high temperature hydrothermal sites have been identified at a range of ocean spreading centres [2], significant massive sulphide deposit formation has been recorded at 165 of these sites [3].To date only 13 deep sea sulphide deposits have undergone intrusive investigation (drilling or coring) and of these, only 6 sites have published tonnage estimates [2]. Almost all research and drilling of SMS deposits has been focused on active systems, the investigation of the morphology, subsurface structure and mineralogy of hydrothermally extinct seafloor massive sulphide (eSMS) deposits is almost non-existent.As such, little is known about the mechanisms that operate post-SMS formation and which have an impact on the preservation and hence resource value of SMS. Identifying these generic processes and mechanisms, and the extent to which they impact the resource grade, is critical in evaluating the global potential of SMS."

Jan 1, 2017

By S. K. Kawatra, H. J. Haselhuhn

"Thickening is used during two primary mineral processing operations: water removal and desliming. During water removal, the pulp density is increased through the injection of flocculants. These flocs settle and create a dense pulp while clarified water is removed through the overflow. During desliming, fine particles are removed through the overflow. Desliming can also be used as a mineral separation process known as selective flocculation-dispersion, where valuable minerals are flocculated and gangue minerals remain dispersed and exit through the overflow.There are many ways to analyze thickener performance on a laboratory scale, but these analyses often do not correlate well with full-scale performance. Some pilot-scale systems have been designed using a semicontinuous approach, but the amount of material required to perform their tests can make semicontinuous pilot thickeners impractical for most applications. This paper focuses on the design and optimization of a continuous pilot-scale deslime thickener that requires minimal material to operate. The design, optimization strategy, and an example study of reagent selection are demonstrated. IntroductionMany laboratory methods have been employed to size and optimize thickener performance. The most common of these include the Coe and Clevenger method and methods derived from the Kynch theory of sedimentation. The Coe and Clevenger method was developed in 1916 and was proven for slurries that do not require flocculation to settle. This method proposed that the settling rate of the pulp is only a function of the solids concentration. It is executed by creating slurries of several different concentrations of solids and performing bench-scale settling tests in graduated cylinders. For each concentration, a thickener unit area can be determined using the following equation (Coe and Clevenger, 1916; Laros, Slottee and Baczek, 2002):"

Jan 1, 2017

By Brian D. Barkauskas, Terence P. Holman

A major combined nuclear and coal-fired power plant, located in on the western coast of Florida has undergone multiple upgrades in recent years to increase power output and enhance environmental controls. Construction of new elements within the existing plant structure required working in highly congested conditions and heavy crane lifts with large picking radii. The largest crane pick involved the use of an 1800 metric tonne capacity Mammoet PTC ring crane for a single long-radius, high altitude lift of a precipitator unit. Original bid tender documents had called for drilled shaft foundation support, but the presence of many critical utilities and unfavorable access for cost effective construction led specialty contractor Moretrench American Corporation to propose an alternate micropile foundation on the basis that high capacities could be achieved in the weak limestone geology and that the smaller size of micropiles would allow for more surgical installation in the utility-congested areas. This case history describes the design and construction of seventy three (73) high capacity micropiles for the value engineering alternative and the crane foundation for this critical lift. Each micropile was founded in a competent dolomitic fossiliferous limestone unit at typical depths of 23 m below existing ground surface. Strain gauge instrumented load testing was used to validate the geotechnical design parameters in the weak limestone bedrock and resulted in the finding that the entire test load was being carried in the upper half of the bond zone. Construction of the production micropiles required numerous relocations due to utility conflicts and local reanalysis and redesign of the 1.2 m thick reinforced concrete ring beam cap. Crane foundation performance was satisfactory and the effective life of this temporary foundation was only 6 months before decommissioning and demolition.

Jan 1, 2017

By Ahmad Ghahreman, James McNeice

"Cerium is the most abundant rare earth metal and is often found in deposits along with small amounts of more valuable metals such as neodymium and gadolinium1. As a result, the production of cerium oxide often exceeds market demands, thus in some cases it would make more sense to remove the cerium from the process solutions before further purification. A common method of cerium removal is to precipitate CeO2 from the acidic leach liquors by raising the pH to oxidize cerium(III) to cerium(IV). This study investigates the oxidation kinetics using three oxidants; hydrogen peroxide, sodium hypochlorite, and potassium permanganate. The effect of oxidant, pH, cerium concentration and temperature on the oxidation kinetics will be discussed. Cerium oxidation in solutions with pH ranging from 1.0 to 4.0 was investigated at cerium concentrations ranging from 2.0 g/L to 16.0 g/L. A cerium recovery of 40% can be achieved at different conditions with each oxidant at room temperature, with higher recovery at 60°C.INTRODUCTION Over the last 70 years, the rare earth elements (REE) have become crucial components of modern technology. These metals are categorized as light rare earths (LREE) or heavy rare earths (HREE) by governments and miners based on weight, abundance, and therefore value. The minerals bastnaesite, monazite, and xenotime compose the majority of the world?s exploitable sources of these metals (Binnemans, 2013; Parker and Baroch, 1971). Geologists classify the LREE ores as „cerium group? minerals, approximately 50% cerium oxide by weight. The cerium group minerals monazite and bastnaesite compose the majority of world production, leading to an overproduction of cerium relative to world demand. This ratio of light to heavy REE in deposits has led to a phenomenon referred to as the balance problem (Binnemans et al., 2013). As an example, to produce 1 tonne of europium oxide from a bastnaesite deposit 450 tonnes of cerium oxide must be processed. This means that any push to increase production and access the value of the HREE metals will drive down the value of the LREE metals leading to diminishing returns (Zepf, 2016). These ores also contain measurable levels of thorium, subjecting them to complex radioactive waste regulations. During the 20th century, the USA was the largest producer of rare earth metals (REMs), primarily sourced from the Mountain Pass mine in California. However, due to a combination of market dynamics and regulations, China has dominated the market for the last two decades. The largest Chinese REE mine, Bayan Obo, produces rare earth (RE) concentrate as a byproduct of iron mining, decreasing their relative production costs (Gupta and Krishnamurthy, 2005). This mine alone represents about half of world bastnaesite production (Zhi and Yang, 2014). Rising demand for high-tech products has forced Chinese producers to commission other large mines, climbing to 90% of world production in the early years of the new millennium (Mancheri, 2016). This presents the west with a looming supply risk of these critical metals in the future."

Jan 1, 2017

By Mohamed Mekkawy, William W. Wheaton, Ira Brotman

"The Virginia Port Authority and the U.S. Army Corps of Engineers are partnering to construct the Craney Island Eastward Expansion (CIEE) to meet the dual purpose of extending the life of Craney Island as a dredged material management area and providing land for a state-of-the-art marine terminal. The over 500-acre (200-hectare) expansion provides additional upland dredged material capacity for the Hampton Roads Harbor by constructing perimeter dikes, that once filled, will provide land for the development of a container terminal. In the winter of 2010/2011 the first stage of sand fill was placed, followed by the installation of approximately 12 million linear feet (MLF) (3.6 million linear meters, MLM) of marine PVDs. With over 36 MLF (10.9 MLM) of PVD required to complete dike construction the project will be one of the largest PVD installation project in the U.S.This paper details the challenges associated with the construction of the cross dikes, in particular the design, testing, installation and monitoring of prefabricated vertical drains (PVDs) installed overwater to depths of over 130 feet (40 meters) for foundation improvement in the insitu very soft Norfolk Clay. With expected settlements of 20–30 ft (7-10 m) and 30 percent average strains, the discharge capacity of the PVDs was of particular concern. Laboratory data is presented showing the magnitudes and variability of discharge capacity under different confining pressures in both a straight and buckled condition.The method of installation and monitoring of the marine PVDs in open water included developing a specialized barge and sophisticated positioning and data collection system to verify installation location, depth of penetration and track quantities. An observational method, including material testing, detailed surveys, periodic in-situ testing, and instrumentation, was utilized by the project team to assess the project’s progress and allow for validation of consolidation and strength gain rates and magnitudes."

Jan 1, 2017

By A. J. Hofmann, G. P. R. van der Merwe, J. E. W. Holm

"A new approach is proposed to perform relativistic comparisons between alternative operational risk management solutions by taking into account the impact of each operational activity on overall system performance. A specific case study, to which this new approach is applied, involves the deployment of safety systems in underground mining operations. Conflicting objectives to be satisfied are the minimization of risk to human lives and the minimization of production losses. As the focus in this case is primarily on the mitigation of risk, the approach that was applied is referred to as activity-based risk (ABR) analysis. Existing development process and risk management methods used in the South African mining environment were analysed by means of observations, a case study, technical documentation, and literature review. It was evident from this analysis that a discontinuity existed between the acquisition and operational phases in terms of the management of safety risk in the acquisition of electronic safety equipment when viewed from a full lifecycle perspective. This discontinuity could be addressed by defining a risk perspective in the system development phase by employing ABR in the preliminary design phase of a system’s engineering life-cycle. The focus of the ABR system development process is to find the functional definition and configuration of safety equipment that addresses both safety and productivity when taking into account human performance variability. In doing so, a balance between productivity and safety is found in a relativistic sense. IntroductionIn any system life-cycle, two major phases exist, namely system acquisition and operation (including maintenance). A distinction is made between acquisition and procurement, where acquisition includes system development and integration as specific engineering activities. In the development phase of a new system, conceptual design, preliminary design, and detail design phases follow in this order to define a complete system, after which the system is put into production and implemented in an operational environment—these activities chronologically define system acquisition in the context of this paper. It is not uncommon that differences exist between the risk management perspective during acquisition of a system and risk management perspective during operation, where nontechnical aspects are often ignored during acquisition, but are then encountered and found to be problematic during operation (Leveson, 2012). These differences also exist in the mining industry."

Jan 1, 2017

By N. Sahin, M. Can, Z. Ekmekçi, Y. Öztürk, Ö. Biçak, I. B. Çelik, B. Kocabiyik

"In this paper, a case study from Çayeli Bakir Isletmeleri A.S. (Rize, Turkey) about the selective flotation of copper minerals from sphalerite is discussed. Çayeli Cu-Zn Sulfide Ore contains different ore types, such as yellow ore, clastic ore, bornite-clastic ore, bornite-yellow ore, and black ore. For some of these ore types, selective flotation of copper and zinc is very difficult presumably due to presence of secondary copper minerals such as bornite, chalcocite and covellite, and also surface oxidation. These factors affect Cu-Zn selectivity due to activation of sphalerite particles in the ore during the process. The main objective of this work was to improve Cu-Zn selectivity by optimization of the pulp chemistry for different ore types of Çayeli ore. After preliminary flotation tests investigating effects of different chemical conditions, a plant survey was performed to determine the plant performance and sources of the problems when problematic bornite-clastic ore is treated in the plant. Various chemical conditions are tested in the laboratory scale test for better depression of sphalerite in copper flotation circuit. Combination of Na2S+ZnSO4+MBS was found to be the most effective depressant scheme. INTRODUCTION Ore variability is one of the most important factors affecting performance of a process plant both in short and long term planning. The geometallurgical modelling becomes a common tool to determine ore variability problems and develop the most efficient solution during life of mine (1, 2). Flowsheet design and equipment selection and sizing are usually done based on the results of ore variability test works. However, in some cases ore variability may not be foreseen during the design stage and therefore the solutions should be developed based on the existing flowsheet and equipment in the plant. In this situation, ore characterisation, problem statement and diagnostic testing should be applied step by step. The problem could be due to changing feed grade, mineralogical characteristics, grindability and surface characteristics when flotation is involved. The variability in feed grade with fixed mineralogy can be handled with relatively simple modifications (i.e. adjusting throughput or equipment capacity) in the plant. Variability in ore mineralogy is the most complex and difficult problem to tackle. Because, mineralogical variations could bring variations in mineral composition, texture and liberation. These variations can potentially lead to the variations in grindability of the ore and flotation behaviour. Variations in grindability are usually managed by optimization of operational parameters in grinding circuit, as it would be costly to replace the existing equipment in the circuit (3). The variations in flotation behaviour are mainly due to variations in mineral types and distribution, texture and surface oxidation. One or all of these factors could be observed in a flotation operation. Therefore, a comprehensive investigation both in plant and lab scale should be conducted for definition of source of the problem. The testwork to solve the problem and retrieve the performance is planned and conducted depending on the source of the problem (4, 5)."

Jan 1, 2017

By Paulo Couceiro, Manuel Lopez Cano

"The Panama Canal is one of the most important engineering projects of the modern era and plays astrategic role in the global economy and international maritime trade since its inauguration in 1914. Now, a little more than one century later, the final phase of its expansion program, the largest infrastructure works undertaken since its inauguration, has concluded. This expansion program has created a new lane of traffic along the Canal with the construction of a new set of locks – one on the Pacific side and another one on the Atlantic side -, increasing the Canal’s capacity and its impact on the world’s economy even more."

Jan 1, 2017

By Jaeheon Lee, Junmo Ahn, Isabel F. Barton

"Newmont’s Mike prospect, currently undeveloped, is a blind Cu-Au(-Zn) deposit on the Carlin Trend, containing >8.5 M oz. Au, 1027 M lbs. Cu, and 809 M lbs. Zn as Carlin-type gold and polymetallic Cu-Zn minerals in Paleozoic lower-plate carbonates and shales. This project was undertaken 1) to examine the effectiveness of different lixiviants for leaching the Mike supergene Cu-Au ores via bottle roll tests, and 2) to determine what ore minerals resist dissolution in each leaching agent by comparing the mineralogy and chemistry of head and tail samples. Sulfuric and sulfurous acids were used to leach copper and cyanide was used to leach gold. Thiourea, glycine, and other lixiviants were used to leach both base metals and precious metal. QEMSCAN and SEM study of six samples of different ore types and grades indicate that the Au occurs as varieties of native gold, including auricupride and electrum. Major Cu minerals are native Cu, cuprite, malachite, chrysocolla, and conichalcite (Ca-Cu arsenate), with locally significant Cu in jarosite and goethite. Gangue mineralogy is dominated by quartz, sericite, chlorite, alunite, smectite and kaolinite, K-feldspar, and iron oxides (sensu lato). Results of bottle roll tests and leach residue mineralogy will be presented and discussed at the conference.INTRODUCTION Resource and Geologic Setting The Mike deposit is a large, blind Cu-Au(-Zn) deposit in the Maggie Creek district of the Carlin Trend of Nevada, USA, near the Gold Quarry mine (Figure 1). The mineral inventory, based on drilling, is 8.568 Moz. Au, 1027 M lbs. Cu, and 809 M lbs. Zn at average grades of 0.72 g/t Au, 0.34 wt% Cu, and 2.13 wt% Zn (inventory for a cone at $400/oz Au and $0.80/lb Cu by Norby and Orobona, 2002)."

Jan 1, 2017

"As mine head grades decline and orebodies become more complex, traditional mineral processing techniques and flowsheets to achieve saleable concentrate become more difficult to design and construct. Mines with lower quality concentrates or concentrates with penalty elements are particular under threat. The economics of these operations are far more susceptible to metal price, concentrate treatment terms and the availability of other, cleaner concentrates. Additional value may be realised for these orebodies through improved recovery by producing a low grade middling concentrate for further processing, in conjunction with a saleable concentrate.The most cost effective way to reduce impurity levels is to do so as early as possible in the mining value chain. Technologies such as fine grinding and fine particle flotation are well established as effective methods for impurity rejection in mineral processing. What is normally overlooked is how a hydrometallurgical process could also be integrated in the overall flowsheet to achieve higher overall recovery at the mill. In the base metals environment, this is mainly because hydrometallurgical processes are associated with production of metal or use of expensive and toxic precipitating agents once the minerals of interest are solubilised. These processes can be very expensive, particularly with rising power costs and poor economies of scale in capital costs associated with low production rates from middling streams.Glencore Technology (GT) has recent experience in the treatment of middling and low grade concentrate streams as well as tailings streams to compliment a concentrator flowsheet in a refractory gold and base metals setting. The value proposition is the isolation of a low grade middlings concentrate from the primary circuit or the tailings stream for upgrading to an intermediate product with an equal or higher grade than the primary concentrate to allow blending for sale. This allows plants to operate on a more favourable part grade-recovery curve while avoiding the expense of metal production. For existing operations this is particularly attractive since it can be added on with no process interruptions.Two case studies are examined showing flowsheets and costings to arrive at the value proposition of the GT low grade treatment flowsheet."

Jan 1, 2017

By Ray Nivens, Umit Turunc, Caroline Sui, Nick Morrison, Douglas Steiner

"In most copper mines and concentrators, mill water is continuously recovered and reused, with fresh water added to make up for losses. When mixed, these water chemistries can lead to severe scaling, especially in pipes, tanks and pumps on the mill water supply side, reducing flows and causing significant production losses.At KGHM Robinson Nevada Mining Company, increases in the fresh water addition ratios resulted in severe scaling problems and premature pump failures thereby jeopardizing plant production. What initially appeared to be a few isolated scaling events eventually unfolded into a recurring pattern of water supply-related production losses with increasing severity. Through completion of detailed root cause analysis, chemistry modeling, laboratory work, in-plant testing and system engineering, the mechanisms of scaling were identified and addressed.Advancements in fresh water addition practices and antiscalant application methods resulted in a stepwise reduction of the mill water scaling. Cost savings and production benefits were significant to the plant’s financial metrics.IntroductionThe production of mineral and metal concentrates using the flotation process requires large quantities of water. Flotation is utilized as the primary means for beneficiation with sulfide ores. Mined ores are crushed and ground into a slurry of 20-55% solids. For each ton of ore, 400-900 gallons of water1 are needed to supply the grinding mill. Additional water is needed in the flotation circuit as well. With many modern mills operating at2 11,000-165,000 tons/day, water supply volumes can be upwards of 3,000 gpm to 100,000 gpm of flow.For plants operating at or above capacity, disruptions and restrictions in water supply flow can have a direct impact on the production and recovery of the metal. Water supply flow can be limited for a wide variety of reasons but of interest are those limitations that are due to mineral scaling. Mineral scaling is the selective point precipitation of inorganic species above saturation concentrations. Precipitated species form flow-restricting deposits in the mill water system (tanks, pumps, pipe and valves), that will eventually impact water supply to the concentrator."

Jan 1, 2017

By Cassandra A. Wetzel

"Rock socketed mini-piles are a desirable foundation alternative when design capacity is more than 40 tons and there is limited access. In this case history mini-piles were designed to support between 75 and 200 kips at 12 locations adjacent to a perimeter wall, a party wall and at cast iron column piers. Limited geotechnical information, low overhead clearance, and active building population tested the creativity of the team to get the piles installed. The key geotechnical concern during installation of the mini-piles was the presence of a glacial till layer above the bedrock surface that restricted the seating of the casing into bedrock with a track mounted drill rig. Soil loss during the advancement of the rock socket using an air hammer was excessive and increased the risk of subsidence. Over a three week period the engineer worked with the contractor to modify the design, means, methods, and materials to install piles with adequate load capacity. This paper will present the changes in design and construction methods that were required.INTRODUCTIONRock-socketed mini-piles are a common and desirable deep foundation alternative to support loads more than 40 tons in New York City. Limited vertical clearance, accessibility, vibration control, and load capacity make this pile type attractive; it also does not require a static axial load test when socketed into rock. This added benefit makes this alternative all the more feasible.The installation of a drilled pipe extending to bedrock through a glacial till deposit presented challenges to the contractor and engineers to confirm the casing is seated sufficiently into the rock prior to drilling the rock socket. The loss of soil between the steel pipe and the till/bedrock interface can compromise the performance of the pile and soil loss can result in settlement of the ground surface.This paper presents the design and construction method changes made on one project during the installation of ten limited access rock socketed mini-piles."

Jan 1, 2017

By John D. Thornley

Alaskan villages typically store a one-year supply of fuel to reduce significant delivery costs. Alaska Village Electric Cooperative (AVEC), an electric utility cooperative providing power to 51 Alaska villages, has made a concerted effort to upgrade and improve their undersized and aging facilities. The Village of Stebbins, located south of Nome on Norton Sound is receiving upgrades to its AVEC bulk fuel facilities. Stebbins offered unique challenges from a foundations perspective due to the nature of the soil. The geotechnical investigation found the soil below roughly a third of the footprint of the bulk fuel facility to be thawed with seasonal freezing and the remainder was found to be warm permafrost with ground temperatures of between 30°F and 32°F. This is a unique and challenging arctic engineering design issue because foundations are designed differently for frozen ground conditions. Driven piles were selected because of site constraints, such as the design flood elevation and the change from thawed to frozen ground conditions. The pile design specified that the pile embedment depths would be selected based on the results of pile driving analyzer (PDA) testing during construction in the thawed ground and maintained within the frozen ground portion of the footprint. Difficulties during pile driving in the frozen ground resulted in several piles becoming severely damaged, requiring subsequent removal. This resulted in a reevaluation of the means and methods for pile installation. Additional fieldwork was performed to further characterize the subsurface soils and their frozen nature. Options for installation of piles in difficult areas were evaluated including ground thawing, predrilling, and reducing embedment depths. Presented within this paper are the findings from the initial and subsequent field explorations, discussion of the design methodology, and the decisions that led to successful installation of piles at this challenging remote village.

Jan 1, 2017

By Michael Laing

Blasting regulation and restrictions are tougher today than ever before. When blasting in population centers, strict limitations are often placed on the environmental effects caused by blasting, more specifically vibration and overpressure. Blast-induced vibration can be a tricky thing to manage at times, but there are a variety of options at our disposal to help optimize and manage vibration. This paper focuses on the application of rudimentary signature hole analysis to optimize blasting vibration in localized areas surrounding a mine.

Jan 1, 2017

By Natalia Konstantinova, Kira Mizell, James R. Hein, Georgy Cherkashov, Amy Gartman, Mariah Mikesell

"Two types of metallic deposits have been found in the deep Arctic Ocean: Hydrothermal Fe, Cu, and Zn sulfide deposits form along Gakkel Ridge in the Eurasia Basin and associated ridges between Greenland and Europe; and iron and manganese oxide crusts (Fe-Mn crusts) and nodules, precipitated from seawater onto rock surfaces in the Amerasia Basin, contain many rare metals of economic interest. Fe-Mn crusts and nodules collected in the Amerasia Basin during 2008, 2009, and 2012 cruises on the USCGC icebreaker Healy are characterized by unique mineral and chemical compositions, very high Fe/Mn ratios, fast growth rates, and other unique characteristics compared to those formed elsewhere in the global ocean. These characteristics reflect temporal and spatial variations in geological, oceanographic, and climatic conditions in the Arctic Ocean and surrounding continents over the past ~15 Myr.RESULTS AND CONCLUSIONSDiscrimination diagrams show that the crusts and nodules found in the Amerasia Basin north of Alaska are hydrogenetic. However, the mineralogy is not typical for hydrogenetic Fe-Mn crusts and nodules, which usually include only amorphous Fe oxyhydroxide and ?-MnO2 (vernadite). The Arctic samples also include the Mn oxides birnessite and 10Å manganates (todorokite, buserite, asbolane), and the Fe minerals also include goethite, lepidocrocite, feroxyhyte, and ferrihydrite. This mineralogy reflects formation under lower oxygen conditions than typical for samples formed elsewhere.The Amerasia Basin crusts have a unique chemical composition compared with crusts from other areas of the global ocean. The key difference is the high Fe contents relative to Mn contents, which determines the types of trace metals hosted by the Fe-Mn oxide phases, and their concentrations. The high Fe/Mn ratios reflect the expansive continental shelves (>50% of the Arctic Ocean) and upper slopes that support redox cycling and release of Fe and other metals to bottom waters, and to the large fluvial input from North America and Siberia. Brine formation on the shelves and currents promote the distribution of the metals throughout the Amerasia Basin, including the deep basins."

Jan 1, 2017

By Stephen C. Tadolini, Minova USA Inc., Peter S. Mills, David R. Burkhard

"Fiber-reinforced spayed concrete has been used for several years in civil and tunneling operations. Research conducted to reduce cure times and increase compressive and flexural strengths resulted in the development of Tekcrete Fast®, a cementitious product capable of obtaining 41 MPa (6,000 psi) compressive strength and 8 MPa (1,200 psi) flexural strength in only 3 hours and reaching 7 day strengths of 62 MPa and 11.7 MPa (9,000 and 1,700 psi), respectively. A single bag product that uses conventional shotcrete and gunite application systems make it a natural crossover product for mining applications. The discovery of incredible adhesion properties and high resistance to chloride permeability helps ensure long-term stability and increases the ease of application. Project results from Disaster City® in Texas and the application for rehabilitating a coal mine belt entry are presented. The case study illustrates the effectiveness of the product in stabilizing a coal mine beltway and adjacent cross-cuts that were subjected to progressive sloughage due to humidity and cyclical loading. INTRODUCTION Original research produced a shotcrete formulation that extends beyond stabilization and can be used to restore the structural integrity of damaged infrastructure. The primary challenge was to develop a shotcrete or gunite that had structural strength within a few minutes to prevent parasitic loading, allowing ingress into damaged structures minutes after applying the mix formulation. This also applies to mining conditions where rapid support of progressive failures can minimize failure. An additional benefit was discovering that the product had extremely high adhesion properties in addition to high flexural strengths. The approach to product design was the development of “single bag” dry mixes that are entirely self-contained, can be rapidly transported anywhere in the field or underground, and can be deployed using simple equipment. Dry mix eliminates issues relevant to high shear water mixing because water is added in the form of a mist at the point of delivery; thus a low water-to-cement ratio can be achieved. However, since there is no onsite powder mixing, the product must have a high degree of inherent homogeneity. Minova offers a commercial version of this material, Tekcrete Fast®, a product that has been successfully deployed in the mining industry and is currently being used in civil, construction, and tunneling operations. The material can rapidly stabilize lose ground in metal, nonmetal, and coal mines. This paper described the technology development, product testing results, and applications and describes a case study to stabilize a coal mine beltway."

Jan 1, 2017

By Farzad Khodabakhshi, Adrian P. Gerlich

"Multi-pass friction stir processing (FSP) was performed to fabricate a new Al-Mg-Graphene nanocomposite. Microstructural developments and distribution of graphene were studied by using electron backscattering diffraction (EBSD) and transmission electron microscopy (TEM) analysis. In the stirred zone (SZ), grain structure was refined down to about 2 µm attributing to the operative dynamic restoration mechanisms and the locking effect of graphene phase. As a result, the yield strength of Al-Mg alloy was improved more than two times due to incorporation of graphene nano-sheets. Also, the indentation hardness resistance of nanocomposite was increased up to ~60%.INTRODUCTION Aluminum-matrix nanocomposites have garnered significant in recent years due to their superior performance and potential advantages for several industrial applications including the automotive and aerospace sectors. Among various reinforcing nano-materials, carbon-based structures featuring sp2 or sp3 hybridization bonds have been found to offer considerably improved physical and mechanical properties. Such carbon allotropes form at micro- and nano-scales including; graphite, carbon nano-tube (CNT), nano-fiber, and graphene. The potential of two-dimensional (2D) carbon materials was introduced in 2004, with the development of graphene as an alternate 2D allotropic form of the carbon structure with a honey-comb lattice at the atomic-scale. It has been shown that it is currently among the strongest materials ever tested with an intrinsic tensile strength of 130 GPa and Young’s modulus of 1000 GPa, and also offers unique thermal and electrical properties.To fabricate metal-matrix nanocomposites reinforced by graphene nano-sheets with typical metallurgical processing techniques, some attempts have been reported in the literature for various solid-state techniques including; hot rolling, mechanical alloying, and friction stir processing (FSP) of pre-cast plates or surface dispersed graphene oxides. The main challenge in those methods was to facilitate the considerable high temperature and pressure for attaining a uniform dispersion of the nano-sheets during the consolidation process. In most cases, significant difficulties have been reported in obtaining a uniform dispersion of graphene within the metal matrix. Among various techniques for production of metal-matrix nanocomposites, FSP has attracted significant attention as a method of surface modification since it was first reported by Mishra et al. In this process, a non-consumable rotating tool is plunged into the surface of material for the aim of microstructure modification. Extreme material plasticity is induced without melting as a result of friction between the tool and workpiece. Frictional heating and severe plastic deformation induced by the FSP process enables metal matrix nanocomposite fabrication by softening the base material and mechanical stirring to disperse the reinforcing nano-materials into the matrix."

Jan 1, 2017

By Peter Hayes, Evgueni Jak, Taufiq Hidayat, David Grimsey, Denis Shishin

"An integrated nickel flash smelter is operated with Peirce-Smith converters at the Kalgoorlie Nickel Smelter. To improve the partitioning of arsenic between slag waste and matte product, an option to modify the slag–matte chemistry by addition of CaO was analysed. A combination of plant sample analysis, high-temperature laboratory experiments and thermodynamic modeling was carried out to evaluate the process options. The high-temperature experiments involved the re-equilibration of industrial matte-slag samples at 1225 °C and P(SO2) = 0.12 atm, rapid quenching in water, and direct measurement of phase compositions using electron probe X-ray microanalysis (EPMA) and Laser Ablation Inductively Coupled Plasma Mass Spectrometry (LAICPMS). A private thermodynamic database for nickel sulfide smelting and converting was used together with the FactSage thermochemical software package to assist in the analysis of the distribution of elements between slag and matte as a function of CaO addition. The thermodynamic predictions combined with experimental data obtained in this study can be used to characterise the effect of CaO fluxing on the slag–matte thermochemistry during the nickel sulfide converting.INTRODUCTION At the Kalgoorlie Nickel Smelter (KNS), nickel sulfide concentrate is processed in an Outotec-type flash furnace to produce nickel matte containing +47 wt% Ni. Separation of nickel matte and waste slag from the flash smelting is enhanced through settling in the electric arc -heated zone attached to the flash furnace. The flash furnace matte is further processed in a Peirce-Smith converter to produce Ni-rich matte containing +66 wt% Ni (Crundwell, Moats, Ramachandran, Robinson, & Davenport, 2011). Iron silicate-based slag is used in the converting process at KNS. Most of the arsenic is contained in the final matte and very little of the arsenic partitions into the slag. Previous work by Font et al (Font, Hino, & Itagaki, 2003) shows that the distribution ratio of arsenic between calcium ferrite slag and nickel-matte (LAsslag/matte) is significantly higher than that between iron silicate slag and nickel-matte, where LAsslag/matte = (wt pct As in slag)/{wt pct As in matte} (1)"

Jan 1, 2017

By Michael Hitch, Jiajie Li

Dramatical increase in the CO2 concentration in the atmosphere has led to the climate change, which poses a significant threat to human life on Earth. CO2 sequestration via mineral carbonation is the one of the most effective method for mitigating global warming, and is the only way that could store CO2 permanently. In recent years, integrating mineral carbonation via ultramafic mine deposit has received significant attention due to its high potentiality towards commercial application. This review compiles the work conducted by various researchers over the last few years on integrated mineral carbonation processes in mining industry, which use the mine waste materials as CO2 feedstock for mineral carbonation. This paper initially introduces the basic theory of mineral carbonation, with a brief description of various techniques that enhance the rate of mineral carbonation. The enhanced mineral carbonation strategies include pre-treatment of feedstock by thermal, chemical and mechanical activation, and carbonation in a direct or indirect carbonation routes under gas/solid phase or aqueous phase. This paper then introduces the scope of application of integrated mineral carbonation. This includes the types of mine suitable for integrated mineral carbonation, the properties of mine waste materials preferable for CO2 sequestration, and the worldwide locations potentially viable for integrated mineral carbonation. Moreover, this paper critically reviews and discusses the integrated mineral carbonation process in mining industry. The integrated mineral carbonation processes include modified passive carbonation techniques at tailing dams, and ex-situ carbonation routes using fresh tailings. The focus of the discussions is the role of reaction condition on the carbonation efficiency of mine waste with various mineralogy, and the drawback of each integrated mineral carbonation process. All the discussions lead to the suggestions on the technology improvement in the integrated mineral carbonation process. Finally, this paper reviews the economical assessments on the existing integrated mineral carbonation process. Literature to date indicates that the value-add by-products (i.e. recovered metals, valuable carbonated products) play an important role in commercialization of an integrated mineral carbonation process.

Jan 1, 2017

By Tracy Brettmann, Shailendra Endley, Jason Leary, Shashank Valluru

"Augered Cast-in-Place (ACIP) piles have long been used for deep foundation support in sands due to their high capacity and speed of installation. Very little information exists on the effects on capacity if the auger needs to be withdrawn from the hole prior to grouting. This condition can occur due to various reasons including grout plug ups, equipment issues, and grout supply delivery problems. It can become a major problem for the project team if this happens during production because the capacity of that pile is then in question, potentially resulting in re-design, installation of replacement piles and/or schedule delays. This paper compares the results of two high capacity test piles installed into a dense sand where one test pile was installed by first completely withdrawing the auger from the hole after drilling to the pile tip depth and the other test pile was installed utilizing conventional industry standard methods. Identical load tests were then performed on both piles to compare the effects of the two different installation procedures. The load test results were surprisingly similar in this case although the grout take required for the test pile installed in the pre-drilled hole was significantly higher to produce a similar grout return depth.IntroductionAugered Cast-in-Place (ACIP) piles are used extensively along the Texas Gulf Coast due to their combination of high capacity and speed of installation resulting in one of the most cost effective deep foundation systems relative to other options. Soil conditions in this region typically consist of alternating layers of sand and clay in the upper several hundred feet. ACIP piles are routinely installed to depths of over 100-ft to achieve the required capacity depending on the site specific soil conditions and therefore typically extend through and tip into sand layers. Occasionally, due to various reasons like equipment issues and plug-ups, the auger is withdrawn from the hole without grouting. Significant sand in the soil profile could lead to questions about the effect of the auger withdrawal on the pile capacity and load deflection relationship.This paper summarizes the results of two identical pile load tests performed on adjacent piles of the same length with the main difference being one was installed using the standard installation procedure and the other was installed by first completely withdrawing the auger from the hole after drilling to the pile tip depth. The load test results were then evaluated using load transfer analyses to estimate the effect of the withdrawal of the auger on the load-deflection characteristics and capacity."

Jan 1, 2017