Search Documents

By Shadia J. Ikhmayies

"Nanocrystalline fluorine doped tin oxide (Sn02:F) thin films were produced by the spray pyrolysis technique (SP) on glass substrates at a substrate temperature T, = 450 ° C. The hydrated stannous chloride (SnClz.2H20) was used as a precursor and ammonium fluoride (NH4F) and hydrofluoric acid (HF) were used as the doping compounds. A comparison between the compositional, morphological and optical properties of the films obtained by using the two doping compounds was performed by using scanning electron microscope (SEM) observations, energy dispersive spectroscopy by X-rays (EDAX) and transmittance measurements. It is found that the films prepared by using HF have larger grain size, and higher fluorine content than the films prepared by using ~- In addition these films have higher transmittance and higher direct optical bandgap energy. These results are interesting for the use of Sn02:F as a forecontact in CdS/CdTe solar cells.IntroductionTin dioxide is an n-type, wide bandgap semiconductor (about 3.5 eV) and in the form of thin films, it is a transparent conducting material, characterized by high optical transmission (80- 90%) [l]. Sn02:F is the most widely used transparent-conducting oxide material. The transparent-conducting thin films of this oxide are used as electrodes in a variety of optoelectronic devices, as heat mirror coatings in 'smart windows' for buildings, in automobile and airplane windshields, in incandescent light bulbs, in flat-plate and concentrating solar collectors. Tin oxide and zinc oxide, in thin film configuration are technologically important materials because of their applications in photovoltaic cells [2].Among various dopants for Sn02, fluorine is often preferred, because fluorine doping results in films with high transparency and good conductivity [3]. By exploring the literatures, it was found that different sources of fluorine were used to produce Sn02:F thin fihns, among which are ammonium fluoride (NH4F) and hydrofluoric acid (HF) are the most used. Some researchers used~ [2, 4-7] and others used HF [3, 6-8] for doping Sn02 films. Gordillo et al.[7] used both of NH4F and HF and showed that the resistivity of thin films obtained by using HF was lower than that of similar films obtained by using NH4F by a factor of 2.2. They also found that the films obtained by using HF have more random orientations."

Jan 1, 2013

By Walter Voglauer

On May 14, 2011 a chimney blast took place in Vienna, Austria. The blasting operation was part of the demolition works at a former railway fabrication. The demolition works on this ground were done under the leadership of the Austrian construction and demolition company PORR. In agreement with the civil organizations which were involved, the commander of the Regional Military Command of Vienna, Brigadier general Dr. Karl SCHMIDSEDER ordered a reserve force engineer company to demolish the chimney. The concrete planning of the chimney blasting was done by specialist Markus SEWALD who belongs to the HEERESTRUPPENSCHULE (combined armed force school) of the Austrian armed forces.

Jan 1, 2013

By Jose Antonio Silva Souza, Emanuel Negrao Macedo, Iara Ferreira Santos, Otacilio Dias, Luis C. A. Venancio

"The Bayer process alumina production generates 0.7 to 2.0 ton of bauxite residue (BR) and an average of 1.0 ton of C02 per ton of alumina produced. The direct reaction of exhaust gases to reduce the alkalinity of the BR may allow a triple gain: improve the storage conditions, open a range of new applications for BR and sequester from 16 to 102 kg of C02 per ton of alumina. This paper shows the measurement of C02 captured during a pilot scale reaction of a suspension of BR in water with flue gas, produced from direct oil burning. Three different types of reactors were used: one spray tower and two packed columns. The inlet and exhaust gases were analyzed using electrochemical and non dispersive infrared sensors. The pH of the suspension was monitored during and after the reaction to evaluate the buffer effect.IntroductionAlumina is mainly produced from refining bauxite using the Bayer process. This process consists of extracting the aluminum oxide through its dissolution in caustic soda and the separation of insoluble residues. The remaining bauxite residue (BR) although not particularly toxic, poses risks to the environment due to the large volume and its reactivity. According to the latest technology it is stacked on sealed deposits specially constructed. To date the vast majority of the bauxite residue that has been produced was stored and were not incorporated into any existing production processes to significant amount with exception to some extent of the sintering process residue at Russia and China [l]. On the other hand, a strategic goal was set in 2010 by the Bauxite and Alumina Committee of the International Aluminium Institute (formed by the majority of the industries) to reuse 20% of BR in 2025 [2]. China has established the same objective for 2015[1].This paper is a sequel of two others presented at TMS 2010/2012 [3-4] and describes:• A pilot plant assembled for testing the carbonation process of BR with gaseous effluents similar of the refining process.• The methodology used to measure the amount of C02 captured during the carbonation process.• The results of the carbonation process, the C02 capture and the buffering effect of the pH.This process is studied in order to consume minimal power and use the effluent as efficiently as possible in different reactors from low cost to ultra high performance. The process is designed for minimizing the power consumption and equipment investment."

Jan 1, 2013

By Kyle A. Perry

Pillar design formulae have existed for decades, and the guidelines for design stability factors are generally accepted by regulatory agencies and broadly used within the coal industry. Nearly all design pillar formulae are based on geometrical parameters of pillars resulting from empirical investigations, with primary focus on the pillar width-to-height (W/H) ratio and associated shaping constants from regression. The most widely used modern pillar design formula in the coal industry, the Mark- Bieniawski equation, also adheres to this principle. Common practice when applying Mark-Bieniawski equation is to use a coal compressive strength of 900 psi. This reduces the design equation to sole dependence upon geometry. However, recent studies have shown that pillar strength is highly dependent on roof and floor properties, particularly the interfaces between the roof-pillar and pillar-floor. This study utilized numerical modeling using FLAC3D to evaluate the relative effects of varying roof and floor interface and mechanical properties. The results confirm that pillar strength is significantly influenced by the properties of the coal pillar interfaces with roof and floor. The mechanical properties of the roof and floor material have only a minor impact on pillar strength when compared with interface effects. These results were used to formulate design recommendations for existing pillar design methods.

Jan 1, 2013

By Liang Shen

The Cooper River Bridge, the longest cable-stayed bridge in North America, replaces two existing bridges along U.S. Highway 17 and connects the City of Charleston and the town of Mount Pleasant, South Carolina. Two diamond shaped towers support the 1,546 ft long main span over Cooper River and allows for a 1000 ft wide navigation channel. The Charleston high-level approach is 4351 ft long and provides a 250 ft wide navigation channel for Town Creek, while the Mount Pleasant high-level approach is 2,090 ft long. Due to the high seismicity in the region, potential vessel impact, and hurricanes, large lateral loads are expected. From various types of foundations, 10-foot diameter drilled shafts were selected for their high capacity against vertical and lateral loadings. The shafts are founded on a stiff to very stiff lightly cemented calcareous sandy clay or sandy silt layer, called Cooper Marl, which underlies the coastal sediments of the interbedded clays and sands. A group of 11 shafts supports each main tower, while a rock island protects it from vessel collision. A group of 4 to 8 shafts foundations support the other piers of the main span unit. A pair of shafts supports the High Level Approach piers. The shaft tip elevations vary from 120 ft to 230 ft below water line. An elaborate geotechnical investigation was conducted on the site, including a load test program on full-scale shafts under axial and lateral loads. The results of the tests were used to calibrate the lateral and axial soil resistance. The objective of this paper is to present the different aspects of the bridge foundation design.

Jan 1, 2013

By Monte R. Hieb

Study of moisture-induced swelling strain in Pennsylvanian Period rocks of the Appalachian Plateau in West Virginia shows a 2:1 biaxial horizontal anisotropy which trends NW-SE. Oriented in-situ slabs of coal mine roof rock were collected across West Virginia, dry-sawed to size, air-dried to stability, and then monitored for moisture changes and deformations in the horizontal plane through one wetting cycle and drying cycle. Biaxial swelling strains were exhibited in nearly all rocks tested, with maximum horizontal deformations occurring normally-incident to the strike of regional geologic fold structures. This relationship persists as fold strike varies across the study area. A connection with Alleghanian fold development and/or post-Alleghanian fold relaxation is suggested. Deformations were largest in shales, but occurred in sandstones and siltstones as well. During testing, moisture-induced fractures (MIF) developed parallel to the regional fold structure and ranged in size from hairline cracks to sample-destroying cracks that were orthogonal to the observed biaxial swelling strain direction. Preferential wetting and swelling of clay minerals along NE-trending fractures, related to a fold-parallel fracture fabric of regional extent across West Virginia, is the most likely reason for the observed systematic NW-oriented biaxial swelling strains. The testing methods used in this study are simple and inexpensive and produce robust results that offer insight into a regional, anisotropic mechanical weakness that imparts a dynamic, asymmetrical horizontal stress to moisture-sensitive coal mine roof rocks over time. Because a similar mechanical fabric has been reported in Devonian-age shales, these findings may have implications for shale gas developers in the Appalachian Basin challenged by rapid aperture closure rates along horizontallydrilled induced fracture networks in Devonian rocks like the Marcellus Shale. The paper concludes with an example of how the concept of a preferred swelling strain direction might be applied to improve the effectiveness of roof trusses.

Jan 1, 2013

By Guo Chen, Jin Chen, Jinhui Peng

"In this paper, the methods of life cycle assessment for microwave hot air systems, and the concept of green degree were proposed. Greenness evaluation index, evaluation system and evaluation model of microwave hot air systems were established. Also, life cycle assessment processing based on these ideas was introduced. Analytic hierarchy process and fuzzy decision- making method were utilized to establish and solve the greenness evaluation of assessment model, while the scores of green degree in microwave hot air systems were obtained. The results show that Life cycle assessment can be applied effectively and efficiently to the microwave hot air systems.IntroductionHot air systems are an important industrial operation condition, which is used to provide high temperature air for materials processing. Nowadays, high temperature airs are manufactured by the conventional heating processes, in which some ceramic materials are used as heating materials. However, these processes pollute the environment. Therefore, to explore new method to produce high temperature air with low energy consumption and less environment pollution are necessary.Microwaves are now being used in various technological and scientific fields in order to heat dielectric materials [1]. Microwaves irradiation has been explored in materials processing in recent years [2-3]. The main advantage of using microwave heating is that the treatment time can be considerably reduced, which in many cases represents a reduction in the energy consumption as well. Since there is energy absorption but no heat conduction, the heating is very rapid and highly efficient, resulting in energy savings and the shortened processing time [2, 4]. Compared with conventional heating techniques, the additional advantage of using microwave irradiation is that microwave irradiation achieves both internal and uniform heating [5-7]. In addition, it is more convenient to control the microwave irradiation processing, because of no direct contact between the heating source and heated materials with less equipment size and waste [2, 8-9]. Life cycle assessment is used and accepted methods for the evaluation of the environmental impacts of products or systems [10]. Recently, many appropriate evaluation methods have been developed for life cycle assessment [11-12]. These proposed methods usually are employed for the evaluating product and analyzing results [13]. Among them, the analytic hierarchy process and the fuzzy comprehensive evaluation stand out as a popular method utilized in many fields [14-16]. Analytic hierarchy process and fuzzy comprehensive evaluation are a combination of mathematical and statistical technique that is useful for analyzing the effects of several independent assessment aspects on the system goal without the need of the predetermined relationship between the objective function and the assessment aspects [17-19]."

Jan 1, 2013

By C. Fortin

ABSTRACT The subject of gold flotation has been reviewed extensively. Most of these reviews focus on the theories of gold flotation and the physical and chemical effects that may impact the efficacy of the gold flotation process. The current status of gold flotation chemistry as it is being applied in industry has not been widely addressed. This paper reviews current gold flotation practice and research advancements and discusses how these applications tie in with the current understanding of gold flotation chemistry. Survey results from worldwide gold flotation operations are analyzed. Potential future areas of gold flotation research are highlighted.

Jan 1, 2013

By Truan-Sheng Lui, Li-Hui Chen, Fei-Yi Hung, Cheng-Yi Chen

"This research used the austempering heat treatment on the SCM435 thin specimen with a type of double loop and obtained the Cr-Mo bainite structure, and then we could further investigate the mechanical properties of SCM435 bainite structure. Experimental data showed the stability of the mechanical properties of specimen with austempering temperature 830°C for 25 minutes was better than that of 15 minutes. The size of austenite grain affected the strength of thin specimen. After austempering at 830°C-25minutes and salt bath at 290°C, the stability of UTS was better than that of salt bath at 310°C and 330°C. The average hardness of all specimens was about more than HRA70. The specimen with austempering at 830°C-25minutes and salt bath at 290°C-30minutes had bigger grain size of austenite and retained y, it also had higher hardness and strength toughness. So, its stability was improved for tensile strength comparing with traditional tempered martensite process.IntroductionSCM435 is a Cr-Mo steel with high strength and high hardness properties, and it has been widely used in machine parts, shafts, gears and strength screw products [1-3]. However, this system often has lower reliability due to the brittleness of high-temperature tempering and quenching inequality. Considering the austempering heat treatment can obtain the uniform bainite structure to improve the temper brittleness, and the austempering heat treatment is a continuous process that it also has efficiency and uniformity. For the thin plate specimens, the mechanical properties of the bainite structure are better than traditional martempering structures."

Jan 1, 2013

By Enrique Munaretti, Cathy Aimone-Martin, Vitor Rosenhaim, Jair Koppe

Production blasts at one of Copelmi’s coal mine operations will be carried out 100 m (330 ft) from a neighborhood located in the town of Butiá, southern Brazil. Mine management is concerned about the possibility of damages and complaints due to blasting operations at close distances to structures of substandard construction. Blasting in the area is characterized by the use of very low powder factor resulting in confined shots in which movement is restricted to a point of almost undershooting the rock. Over the past year, tests were conducted mainly in the overburden area to determine the best approach to be implemented when blasts move closer to the town. Mine management wants vibration levels to be reduced lower than the damage limits proposed by Brazilian regulations to ensure a safety margin and mitigate perception by the community hoping to reduce the number of complaints.

Jan 1, 2013

By Andy Judge

"In traditional Permanent Magnet Machines, such as electric motors and generators, power is transmitted by magnetic flux passing through an air gap, which has a very low magnetic permeability, limiting performance. However, reducing the air gap through traditional means carries risks in manufacturing, with tight tolerances and associated costs, and reliability, with thermal and dynamic effects requiring adequate clearance. Using a magnetically permeable, high thermal conductivity material has the potential to improve magnetic performance, while at the same time offering performance advantages in heat transfer.Ferrofluids can be used to improve permeability in the rotor I stator gap. However, there are several tradeoffs in this approach. Fluid immersion comes with an increase in fluid friction loss compared to the windage losses of a traditional system. Isolating the rotating components from the ferrofluid can offset this effect. Also, while the magnetic effect can be positive for gap permeability, leakage flux can increase, and saturation can limit gains. These effects must be taken into account for a system optimized for ferrofluid immersion.IntroductionPermanent Magnet Machines (PMM's) convert electrical energy to mechanical energy in motor applications, or, for generator applications, convert mechanical energy to electrical energy through means of passing alternately polarized magnets past electrical coils. Looking at a simplified version of a PMM, where Rx is magnetic reluctance and <l>x is magnetic flux, we have the circuit shown in Figure 1."

Jan 1, 2013

By T. Johnson

Hydrometallurgical processes can be exceptionally corrosive. This is particularly true in acid leaching processes for copper, cobalt, nickel and rare earth elements. In the last five years, several large hydromet plants have been built in North America (Vale - Long Harbour, Baja Mining ? El Boleo and MolyCorp - Mountain Pass). Hundreds of storage tanks, extraction vessels and electrowinning cells along with miles of piping were designed and fabricated to withstand the aggressive environments inherent in these processes. One key element all three projects had in common was the extensive use of FRP in equipment design. As a material of construction, FRP provided equal if not improved durability relative to alternative corrosion resistant alloys at a considerably lower cost. This paper will highlight the extensive use of FRP in these three world scale projects and why it was chosen for each process.

Jan 1, 2013

By Min Zhu, Yu Ji, An-chao Ren

"After being welded in the weld plant, the 100-meter heavy rails with the specification of 60kg/m are found broken during the straightening process in four planes. Failure analysis is made using the optical microscope and SEM with the result showing that the broken rail contains the imperfection of protrusion which exists at the edge of rail foot, about 1 00mm away from the rail end. When the protrusion is peeled off by deseamer from rail surface, cold scratch is generated which causes the rail to be broken during the subsequent straightening process. By adjusting the roll diameter differences between top and bottom roll of universal finishing mill and the height of pass line, it is possible to maintain the rails flat when leaving the mill. This prevents the upsweep and downsweep phenomena and, thus, the imperfection of protrusion can be eliminated. IntroductionThe development of rail transit worldwide has entered into a new era since the 1960s. The hi-tech rail transit system has gradually gained recognition over the world. In particular, the emergence of new-type passenger trains represented by TGV of France, ICE of Germany and Shinkansen of Japan and heavy haul trains as well, has revealed the charming way and more prosperous future of the modern and hi-tech rail transit system to the people all over the world. It should be pointed out that rail transit system is still the most effective solution to traffic jams among urban cities and in the central cities during the 21 '1 century, especially high-speed railway and subway which take overwhelming advantages over air transport, marine transport and road transport in terms of high speed, high efficiency, safety, comfort, environment protection and high flow. With the trend of increasing speed and heavier load of trains, higher product quality of rails is demanded. The rails for passenger dedicated lines require high cleanness, high accuracy in size, high flatness, high surface quality and large size (100-meter fixed length). The rail quality has direct influence on the operating performance of rail and railway traffic safety. The 100-meter heavy rails with the specification of 60kg/m are broken subject to the straightening process in four planes after being welded in the weld plant. This paper analyzes the reason for rails being broken and provides the theoretical proof for determining the rolling process."

Jan 1, 2013

By Roberto Folchi, Hans Wallin, Mara Battocchio

An understanding of explosives science and technology, and the competence to harness it is central to maintaining Explosives capability, national security, and in sustaining a competitive industry. A consequence of eroding this competence is the increased likelihood of explosives accidents. These are often catastrophic as demonstrated by accidents in Nigeria, Russia, Toulouse and Enschede. In addition to the serious loss of life there was the very significant damage to houses, domestic and industrial infrastructure and to the environment at a cost of many millions of Euros.

Jan 1, 2013

By Jilai Xue, Jun Zhu, Baisong Li

"TiB2-C/C Function Gradient Materials (FGM) is used in cathode materials to improve aluminum wettability and melt penetration in aluminum electrolysis. In this investigation, FGM was tested for use as part of the cathode materials, where a 10 mm thick TiB2-rich layer was on the top as an Al-wettable surface, the TiB2-C layers in the middle as a gradient layer and the carbon on the bottom as a base. Electrical resistances ofFGM were determined in the temperature range of25- 9600C in argon atmosphere. The results show that the present of TiB2-C gradient layer can reduce the open porosity and the electrical resistance of the cathodes materials at elevated temperatures. The cathode samples after aluminum electrolysis usually demonstrates an increase in electrical resistance, but the application of FGM layer can compensate such an increase for certain extend due to less variation in porosity and lower the level of melts penetration.IntroductionCarbon is still used for aluminum reduction cathodes dominantly, but it has a poor wetting properties by liquid aluminum and the anode-cathode distance has to be kept about 4-5cm with an additional 1.3-2.0 V voltage drop [l]. TiB2 has better wettability by liquid aluminum with higher electrical conductivity and stronger chemical resistance to the electrolyte attack. And the wettability ofTiB2-C composites cathode on liquid aluminum can be also improved, while liquid aluminum can completely wet the cathode surface ifTiB2 content exceeds 27% [2-4]. However, during the process of TiB2-C composites cathodes preparation and aluminum electrolysis, the deformation by temperature variation or sodium penetration are great disparity between TiB2 and carbon due to their physical properties difference. This will accelerate the cathodes cracking and deterioration."

Jan 1, 2013

By Charles S. Spirakis

The consistent occurrence of organic carbon early in the paragenesis of Mississippi Valley-type sulfide deposits suggests a genetic link between organic carbon and the sulfide ores. Reduction of sulfate in the mineralizing solution by organic carbon at the sites of mineralization is commonly proposed as the precipitation mechanism for these deposits, but inorganic sulfate reduction is too slow to be important to the chemistry of the ore zone, and bacteria, which catalyze sulfate reduction at low temperatures, are not known to survive at the temperatures of mineralization. Sulfate reduction with or without bacteria is not consistent with the sulfur Isotope evidence. Sulfur isotope studies also indicate that the derivation of sulfur from hydrocarbon at the sites of mineralization is unlikely. Organometallic complexing may be involved in the transport of metals, but no plausible mechanism for breaking these complexes at the sites of mineralization has been proposed. Reduction of partly oxidized sulfur species in the mineralizing solution by organic carbon at the sites of mineralization is a possibility which deserves further scrutiny.

Jan 1, 2013

By Thomas A. Printz

The wide use of carbon steel in construction and engineering projects makes this engineering material accountable for approximately 85% of the total annual steel production worldwide. Despite the lack of corrosion resistance of carbon steel, it is incorporated into the permanent work for marine applications, power plants, transportation projects, chemical processing, mining, petroleum production and refining, pipelines, mining and construction equipment. Corrosion is an electro-chemical process that occurs in the presence of water and air. When an electric current is introduced to water or soil, the rate of carbon steel corrosion increases rapidly. Gaseous atmospheric constituents that are capable of electrolytic activity can also increase the rate of corrosion. Corrosion tends to be more rapid in environments in which the steel is exposed to water, and then air, rather than being constantly submerged. The exposure to seawater increases steel pitting because the electrical conductivity is improved in salt water.

Jan 1, 2013

By Armin W. Stuedlein, Seth C. Reddy

In this study, factors affecting the reliability of augered cast-in-place (ACIP) piles under axial compression at the serviceability limit state are addressed using a simple probabilistic hyperbolic model and a database of load tests on ACIP piles in cohesion less soils. The aleatory and model uncertainty in a selected load-displacement model is statistically characterized, and is used to simulate representative random samples from the bivariate random vector of model parameters. A first-order reliability method (FORM) was used to determine the effect of sample size on the stability and uncertainty of the reliability index. Sample sizes greater than about 40 provided relatively consistent estimates of the reliability index; however, its uncertainty continued to decrease with increasing sample sizes. Additionally, the effect of slenderness ratio on the reliability of the serviceability limit state design was characterized and found to exhibit a significant effect on the probability of exceeding a specified displacement.

Jan 1, 2013

By Carlos Maurício Fontes Vieira, Sergio Neves Monteiro

"A ceramic body traditionally used to produce bricks and roofing tiles with kaolinitic clays was reformulated by the addition of sand and illitic clay. The objective was to obtain a ceramic product with better technological properties. Specimens were made by uniaxial press-molding at 20 MPa and then fired at 850, 900 and 950°C. The determined technological properties were: linear shrinkage, water absorption and flexural rupture strength. The results showed that both sand and illitic clay contribute to reduce the water absorption of the industrial clayey body. With respect to the flexural behavior, it was observed that the incorporation of sand decreased the mechanical strength. On the other hand, the illitic, incorporated in an amounts of 30 wt.% contributed to increase the mechanical strength of the clayey ceramic.IntroductionCeramic bodies industrially fabricated in the county of Campos, north of the State of Rio de Janeiro, in Brazil, are still empirically elaborated using a mixture of local clays. These clays are predominantly kaolinitic mineral in nature, associated with high plasticity and elevated weight loss during the firing stage. Due to the excessive plasticity of the ceramic bodies, dimensional defects, which occur after drying and firing are usually obtained. Moreover, the kaolinitic nature and the presence of aluminum hydroxide (gibbsite) confer a refractory behavior to the local clays, which impairs sintering during the firing operation. In the case of clay ceramic products for civil construction, this results in greater porosity associated with elevated values of water absorption and low mechanical strength [1,2]. To avoid these problems, it is necessary to reformulate the ceramic body composition. The addition of both non-plastic materials to reduce plasticity and fluxes to condition the refractoriness is a possible alternative.As an alternative to reduce the plasticity of clayey ceramics sand, which is predominantly constituted of silica, can be used. The incorporation of sand in amounts of up to 25 wt.% to a clayey ceramic body used for roofing tiles fabrication was studied by Vieira et al. [3]. In that work specimens were prepared by extrusion and fired at 850°C. The results indicated that in the pre-firing stages the sand improved the workability of the investigated clayey ceramic body and facilitates the drying stage. It was also observed that the incorporated sand significantly improved the physical and mechanical properties of the clayey ceramic after firing. On the other hand, the apport of flux oxides could be done by the use of illitic clays that have a higher amount of alkaline oxides in comparison with the kaolinitics clays."

Jan 1, 2013

By Yamei Han, Jiang Du, Jinhui Peng, Mengbi Fu, Libo Zhang, Zhengfu Zhang

"A continuously pilot synthesis by microwave-heating was used in preparing the cathode material LiNi113Co113Mn11302 for Li-ion battery, which used Ni1/3Co1/3Mn1/3(0H)2 and LizC03 as raw materials. Decomposition of the raw materials and synthesis of LixNi113Co113Mn11302 would be fmished in single roasting process. In addition, using microwave-heating would reduce the reacting time largely. Furthermore, the yield of LixNi1/3Co1/3Mn1/302 synthetized in single roasting process was 50 kg. Meanwhile, the effects of Li:(Ni+Co+Mn) molar radio (Li:(Ni+Co+Mn)=l.06, 1.075, 1.09, 1.15) was studied in this paper. XRD, SEM and EIS were used in characterizing the cathode material. The results showed that the best Li:(Ni+Co+Mn) molar radio was 1.075. It was found that the LiNi113Co113Mn11302 synthetized with Li:(Ni+Co+Mn)=l.075 had homogenous distribution of particles and ideal layered structure. The galvanostatic charge-discharge(O. l C, 2. 75-4.3V, vs. Lt /Li) tests showed that the initial discharge capacity of the LixNi113Co113Mn11302 was 159.5mAh·g-1, and the discharge capacity was 157.6mAh·g·1after10 cycles.IntroductionRecently, as the cobalt was expensive and the restriction of dynamic power, the commercial cathode Li2Co02 which was expensive, toxic, and high pollution had exposed its defects[1·2l. Since T.Ohzuku[3l first reported the layered LiNi113Co113Mn11302, this material had high reversible capacity and caused the attentions of researchers[4l. Its reversible capacity was l 60mAh/g and 200mAh/g in the voltage range of 2.75-4.3V[5-61. But for the present, preparing LiNiwCowMnw02 by traditional had lots of disadvantages, such as the long heating time, the high cost and the volatizing of lithium and so on[7-9l. According to these, traditional prepatation wasn't good for sustainable development and energy conservation."

Jan 1, 2013