Search Documents

By S. J. Jung

The stability of underground openings for deep mines is critical, since incorrect orientation or geometry of shaft, stope, and accessways often results in the failure of openings due to high stress concentrations. Current state-of-the-art procedures for the design of underground openings are largely based on rules of thumb, experience, and trial and error. Rules of thumb are invariably based on the past experience of the designer and may not remain optimal as the depth and complexity of mine workings increase. Often, as conditions change, and as the interaction between geology, in-situ stress conditions, and mine openings grows more complex, the cost of maintaining structural integrity becomes prohibitive. Existing design procedures for deep mines are rapidly becoming inadequate as mines are worked at greater depths. For example, in the Coeur d' Alene Mining District, several million dollars are spent for inspection, repair, and maintenance on a regular schedule, largely as a result of inadequate design. In these types of situations, it is of critical importance that a new design methodology be developed for the layout and design of underground openings.

Jan 1, 1994

By J. Elbrond

"This paper describes qualitatively the progressive are losses and rock dilution in a mining project from the geological modelling to and including the concentration. A simple theoretical model of the net present value of a deposit, assuming a log-normal grade frequency function, is used to find the pair of decisions on rate of production and cut-off grade, which maximizes the net present value. Various degrees of ore losses and rock dilution are then applied on this optimum, and the resulting decreasing net present values are calculated, as well as the increasing cost of metal and the increasing metal losses as a function of are losses and rock dilution.IntroductionDue to a variety of uncertainties, to inevitable lack of precision in deposit estimation and in mine planning, and due to production constraints, ore losses and rock dilution occur throughout the many phases of a mining project. The phases range from the geological definition of the orebody, over the cut-off grade optimization and decision, over the design of the mining method and the actual mining to the ore dressing, where the final loss of valuable ore into the tailings occurs. Quantification of ore losses and rock dilution are mostly difficult if not simply impossible to obtain. At the end-phase an estimate of the total dilution may be obtained with some degree of precision by observations of the amounts and analysis of concentrate and tailings. It is much more difficult to estimate the total ore losses because the uncertainty of the geological modelling in the initial phase and in the mining phase is very difficult to quantify, despite the use of geostatistics for grade estimation.Many attempts at quantification of ore losses and rock dilution have been made and some examples are shown in Table I. Although they differ widely from each other, it is obvious from these figures that ore losses and rock dilution are significant and have considerable effects on the economical results of a mining operation. Life length, net present value, cost of producing metal and the loss of metal are all affected."

Jan 1, 1994

American Barrick Resources Corp. has come farther, faster in the last 11 years than any mining company in recent memory. Acquisition of Lac Minerals Ltd. in August 1994 now makes Barrick the largest gold producer in the world outside South Africa. In terms of market capitalization, the company is the world's most valued gold producer. American Barrick's 28.3-km2 (7000acre) Goldstrike property on Nevada's Carlin Trend, the primary engine for past growth, was purchased in 1987 for $62 million. Regarded as an attractive exploration target, Goldstrike instead propelled American Barrick to the front rank of world gold producers. In 1993, the company produced 50.75 t (1,631,988 oz), 44.78 t (1,439,929 oz) from Goldstrike. Reserves on the property totaled 905 t (29.1 million oz) at the end of 1993, the largest in North America.

Jan 1, 1994

By M. C. van Blerck

This paper examines the South African fiscal system as it applies to the mining industry and, where components are found wanting, discusses possible alternatives. It is concluded that the South African system has long provided a stable environment for mining investment and growth. However, the introduction, of steep surcharges during the past decade or so (since abolished) and ring fencing (since relaxed but not abolished) has started undermining this stability.

Jan 1, 1994

By C. Cheung, U. Erb

"Over the past few years, nano-processing of magnetic materials has received considerable attention, because many magnetic and other application-specific properties have been shown to be enhanced in materials with ultrafine grain size. This paper reviews recent advances in the production of nano-processed soft magnetic materials such as pure nickel and cobalt as well as binary nickel-iron and ternary nickel-iron-chromium alloys by electrodeposition. Magnetic, electrical and mechanical properties of these materials are presented and discussed in terms of their microstructural defects.IntroductionIn recent years, nano-processing of materials to enhance their magnetic properties has received considerable attention [1-23]. Thin films, compositionally modulated thin films, granular films and bulk materials have been produced by many different techniques. These include gascondensation [1-6], ball-milling [7,8], chemical processing [9,10], metal-organo complex routes, solution reduction and co-precipitation [11], sol-gel methods [12], sputtering [12-14], rapid solidification [15], devitrification of amorphous alloys [16-19] and electrodeposition [12,20,21]. The potential application of nano-engineered materials with enhanced magnetic properties has been specifically discussed for soft magnets [18,19,22,23], hard permanent magnets [15] as well as for layered materials showing giant magnetoresistance effects [13,14] and nano-composites for magnetic refrigeration [11,12].The purpose of the present paper is to review recent advances in the development of nanocrystalline soft magnetic materials by electrodeposition methods. These materials could find applications in areas such as magnetic recording heads, high efficiency electric motors, transformer cores, etc."

Jan 1, 1994

By Don Novotny, Dana Spencer

In this workshop our intent is quite simple; that is that we will introduce a relatively new technology that may have applications in blasting applications. This technology is the laser initiation of explosives. This workshop course is not intended to suggest ways in which specific blasting problems can be resolved. That is the purview of experts within each of your fields.

Jan 1, 1994

The Mining Act (1992) and the Petroleum Act (1980) provide for the Government of Papua New Guinea (PNG) to take up equity holdings in mining and petroleum projects. The price the Government pays for its share is based on the historical cost of exploration and development on the project to the date of government equity acquisition. The equity level to be acquired is not fixed and ranges up to 30o for mining and up to 22.5s for petroleum at the discretion of the Government of the time.The objective of this paper is to examine the pros and cons of State equity holdings in PNG from the point of view of both the State and the developer. Using an economic model of the PNG mining taxation system an assessment is made of the effective return on investment received by the State from such equity holdings. The results are compared with government revenues from other taxation measures.

Jan 1, 1994

By Michael A. Barbaglia, Mark William Withey

The lift shot is an essential blast design in the execution of mine creation and expansion plans. Whether it be opening a new quarry, creating a new level in an existing operation, or for control of water, lift shots are utilized to create the desired results. Lift shots by their nature differ from conventional production blasts because they have no free faces for relief of the blast. Due to this fully confined state, the primary direction of the rock movement is vertical, and the potential for excessive vibration and fly rock generation is great.

Jan 1, 1994

By Hanley J

Coal winning in the Latrobe Valley exceeds 45 mtpa uses a small number of Bucket Wheel Excavators and high speed conveyor systems. While this equipment offers many advantages in the production cycle, incorrect use can lead to low productivity and risks to the safety of the operators and equipment. The mining equipment is of high capital value and easily damaged when used outside the correct operating range. In the extreme case, this can result in total machine collapse, having major implications for personnel safety as well as production and costs. With an active productivity improvement program in the Latrobe Valley in the last two years resulting in a 50 per cent reduction of personnel, many experienced operators have retired. Mine management are facing the urgent need to rapidly train new operators to maintain high productivity levels and reduce the risk of accidents to personnel and high capital cost plant. With the assistance of the Central Gippsland College of TAFE a Certificate Level course has been developed for open cut operators. The course covers all essential training needs for the Latrobe Valley mines. The training is developed from National Competency Standards, allowing transfer of skills, and is flexible to suit other enterprises. It has been written for self-paced learning with the total job understanding, and to have competency-based learning outcomes, training tasks and assessments built-in to modules. With the introduction of this new training program, management is convinced that the element of risk within the mine will be significantly reduced. For these reasons it is an ideal training model for other enterprises.

Jan 1, 1994

By H. Kalsi

"IntroductionRoyal Oak Mines Inc. is currently operating the Parnour No.1 mine located 10.5 miles east of Tinunins, adjacent to Highway No. 101. The operation produces gold ore at a rate of 3300 tpd. A variety of mining methods including bulk open stopes with ITH drilling, narrow vein panel, longhole and open pits contribute to produce 1.2 rnillion ore tons annually. The milling process requires water at an average rate of 1 rnillion gallons per day (700 U.S. gpm). The Pamour No.1 mine has historically had two major problems with regard to water control. The flfSt is the underground pumping system's inability to handle excess inflows of water generated from spring thaws. When the thaw takes place over a short period of time, large inflows of water are created which quickly migrate underground and sometimes result in the loss of the lower loading pocket. During the spring runoff the pumps at Parnour No.1 work continuously for 24 hours at a rate of 1200 U.S. gpm. The system was further taxed in 1991 when the Hoyle mine was connected to the Parnour No. 1 mine and whatever excess capacity the pumping system had for the spring runoff was taken up handling the inflow of mine water generated by the Hoyle.The second problem facing the mine was the lack of water for the mill during the severe cold winter months and dry summer months. At those periods inflows of water into the mine decline and the underground water normally pumped to the mill is severely decreased. In times of dry spells mill personnel increase the water diversion from the Three Nations Lake in order to meet water demands and maintain tonnage throughout. In essence, the mine was going through an annual ""feast or famine"" situation and a solution was needed.A number of options were considered but were narrowed down to the two most practical. The first was to modify the existing pumping system and increase its capacity in order to handle the excessive runoff during spring thaw. This involved a heavy capital expenditure and would have caused additional operating costs (i.e. increased hydro). The option chosen by the management was to divert the spring runoff into an unused section of the mine called The West End. A bulkhead placed at the 2400 level would provide an ultimate underground water storage potential of 150 million gallons. This would also cut down the load on the existing pumping system, save electric consumption in pumping and provide water storage which could be used for milling during the two dry spells. Pumping stored water from the mine could be scheduled for off peak hours to take advantage of lower power rates. To meet these objectives an underground bulkhead capable of withstanding high water pressure up to 2000 ft head (866 psi) was constructed in the spring of 1992. The bulkhead site was at the 2400 level at the Pamour No.1 mine. A major consideration was the requirement to construct a safe bulkhead and to minimize water leakage from the bulkhead.Figure 1 shows the bulkhead location."

Jan 1, 1994

By Tien J. C

Many factors (type of coal mined, water pump pressure, wetting agent concentration, etc) will affect the performance of a dust suppression system using a water spray in an underground coal mine. While a two-level factorial method is useful in

Jan 1, 1994

By T Christie, A Swain

Patterns of quartz veining in epithermal gold-silver deposits at Wharekirauponga, Neavesville and Ohui in the Hauraki Goldfield, have been analysed to determine the effects of different lithologies on vein distributions. At Wharekirauponga, quartz veins are hosted in rhyolite and minor andesite, with the andesite containing slightly higher gold grades. Local basement andesite, rhyolitic tuff and silicified black shale host gold-bearing quartz veins at Neavesville. At Ohui, quartz veins are hosted in rhyolite, rhyolitic tuff and andesite. Fractal analysis was used to quantitatively describe the distribution of veining. The fractal dimension (D) of veining in silicified tuff is 0.25, moderately silicified rhyolite has D = 0.23 - 0.26, clay-altered andesite has D = 0.3, strongly silicified rhyolite has D = 0.3 - 0.39, silicified andesite has D = 0.4, and silicified black shale has D = 0.43. The D values are related to the composition of the host rock, and appear to be controlled by its competency. Hydrothermal silicification results in increased competency and higher D values. Vein thickness frequency plots for different lithologies show that andesite at Ohui, and to a much lesser degree at Wharekirauponga, contains more thick veins than rhyolite and tuff. Gold grades show a strong to fair correlation with higher vein density in three drillholes at Wharekirauponga. The fractal dimension of veining is an important control on fluid flow and gold deposition within an active epithermal system. Vein systems with higher D have a greater density of veining which would have favoured increased fluid-rock interaction. Lower D vein systems have more clustered arrays. The increased fluid-rock interaction induced by a high D vein system, when combined with a reactive host rock, results in an environment which is highly favourable for gold deposition. This situation is seen in the andesite at Wharekirauponga.

Jan 1, 1994

Present value maximisation studies are a useful aid in enhancing the economic performance of open pit mining operations. Maximising present value helps to reduce the risk of financial failure. Maximisation of present value also means that the capital invested is being used most efficiently. A characteristic step in determining the present value of an open pit mining operation is to set out the sequence in which increments of material (ore of various grades and waste rock) are mined. Traditionally, present value maximisation has been performed by selecting a cut-off grade for each increment so as to maximise the present value of the total operation, by an iterative process using computers. Kenneth F Lane has developed a method and applied it to many mining operations. An alternative method for determining the maximum present value of an open pit mining operation is given. In this method the maximum present value is determined by working backwards from the end of the operation life, progressively asking the question of each increment `what cut-off grade maximises the the present value at the start of mining of that increment?' The method allows calculations to be performed by a `spreadsheet' package. Present value determinations are characteristically performed under constant conditions (eg prices, costs) throughout the operation life. Unfortunately real life circumstances are rarely constant, with the costs of mining inputs rising at variable rates. The prices received for mineral products have been shown to broadly trend downwards with time in real terms. Treatment of such changes in the determination of the maximum present value of an operation is discussed.

Jan 1, 1994

The challenge of planning to minimize interaction effects in multi-seam mining is compounded by the difficulties inherent in extrapolating essential geological and spatial data between sampling points. To predict the effects of ultra-close mining on lower seam entry stability, simulated mine openings were studied using finite element analysis and body loaded photoelastic models. Both symmetrical and unsymmetrical loading was used to represent stress fields generated under multi-seam conditions. Results were correlated with field data to determine stress levels at which failure could be expected to occur. Stability predictions require precise definitions of geologic and spatial data, which could not be accurately defined by interpolation between sampling points. To overcome this problem an expanded roof stability model, SESAME2, was developed to incorporate reliability concepts based on Monte Carlo sampling. The model was demonstrated in terms of variations of innerburden thickness using a case study.

Jan 1, 1994

By Ralph Harris, Javier Jara

"Oxygen is essential in gold cyanidation. It is supplied to the leaching media by sparging oxygen or compressed air into the cyanidation tank. The rate of oxygen transfer is critical to achieve the desired oxygen concentration in solution.The performance of a novel device for gas sparging recently developed at McGill University is compared to the mass transfer characteristics of the two spargers most used in the gold industry: the four lance configuration and the inverted cone. The distribution of gas and the kinetics of oxygen desorption of the three types of spargers was studied in a 140 litre tank. The oxygen dissolution of the new device is three to five times faster than the other spargers. This could increase the leaching rate and/or decrease the cyanide and oxygen consumption.IntroductionIn hydrometallurgical processing, it is often necessary to bubble gas through a pulp to carry out the wanted reactions. The gas can act to agitate the pulp and it can also supply reactant. The rates of the reactions which require a reactant supplied by the gas are often dependent on the rates of mass transfer from the gas to the solution.A common example of this is gold cyanidation which requires oxygen for gold dissolution. Since the gold containing slurry is rich in other oxygen consuming substances (sulphide like pyrrhotite), it is important to provide enough oxygen to allow complete gold dissolution within the residence time of the cyanidation reactors. It has been demonstrated that the rate of gold dissolution is directly proportional to the dissolved oxygen concentration of the pulp which in turn is proportional to the oxygen partial pressure in the bubble 1 2 3. Improving the rate of mass transfer of oxygen increases the dissolved oxygen concentration of the slurry and therefore improves the rate of the reaction.The rate of mass transfer from a bubble to its surrounding solution increases with decreasing bubble size and increasing gas bubble residence time which in turn increases with decreasing bubble size. The generation and dispersion of small bubbles is thus critical to achieving high rates of mass transfer. Different configurations and devices used to inject gas have different effects on the bubble size and the residence time, influencing the overall rate of mass transfer. Therefore better mass transfer can be achieved by adopting a more efficient method.The methods tested in this report are the four lance configuration (wall spargers), the inverted cone and a new device, designated HCD. The wall spargers and the inverted cone are used widely in the industry today."

Jan 1, 1994

By D. W. Davis, P. Landais, L. J. Robb

Nodules of carbonaceous matter have been observed in several Archaean peraluminous granites adjoining the gold- and uranium-bearing Witwatersrand Basin. These nodules, which resemble solid bitumen, usually replace uraninite or uranothorite and are paragenetically late. They show many similarities to kerogen seams and nodules associated with the conglomerate horizons in the Witwatersrand Basin, including composition, maturation, intimate association with uraninite, and a late paragenesis. U-Pb isotope ratios for granite-hosted and Witwatersrand kerogens define a single, albeit somewhat diffuse, Ph-loss discordia suggesting an upper intercept age of circa 2300 Ma. Carbon isotope analysis indicates lighter Ol3C values for the granite-hosted nodules than for the sediment-hosted kerogen seams. Raman spectroscopy indicates that granite-hosted kerogen is more highly ordered than Witwatersrand seam kerogen. A model is presented which links the granitoidand sediment-hosted organic matter to an event of oil generation in the Witwatersrand Basin circa 2300 Ma ago. Light hydrocarbons migrated through the sediments and into underlying/adjacent granitic rocks, undergoing polymerization and accumulation in response to radiation accompanying the presence of high-uranium phases.

Jan 1, 1994

By John E. Litz

The Denver Process is a chemical/metallurgical process for treating radioactive or mixed wastes by extraction and concentration of the radioactive and/or hazardous component(s). The process was developed at bench scale, evaluated at pilot scale, and will be implemented at full scale to remediate a low-level radioactive sludge. Six unit operations comprise the process: feed handling, leaching, solvent extraction, electrodeposition, precipitation, and tailing preparation. Unit operation design may be modified to tailor the process for varying feed stock composition. Radioactive or mixed waste is reacted with aggressive reagents in an aqueous phase, solubilizing targeted components. These components are then selectively extracted and concentrated in subsequent steps. Waste solids and solution exit the process as non-hazardous non¬radioactive waste. Dehydration of aqueous waste by submerged combustion eliminates aqueous discharge.

Jan 1, 1994

By Gordon T. Austin

Garnet is the general name for a family of complex silicate minerals having similar physical properties and crystallizing in the isometric (cubic) system. All garnets have the same general chemical formula but vary greatly in chemical composition. The name garnet is derived from the Latin word granatus, meaning like a grain, which refers to the mode of occurrence wherein crystals resemble grains or seeds embedded in the matrix. GEOLOGY Mineralogy Chemical Properties: The general formula for garnet is A3B2(SiO4)3, whereas A can be calcium, magnesium, ferrous iron, or manganese, and B can be aluminum. ferric iron, or chromium, or rarely titanium. The formulas and names of common garnet species are: [ ] Almandite and almandite-pyrope solid solution garnets are the best abrasive types, but andradite, grossularite, and pyrope also are used. All species of garnet have been used as gemstones. The structure of garnet consists essentially of isolated SiO, tetrahedra connected by oxygen-cation-oxygen bonds through the distinct A and B group cation sites. Within this structure magnesium, ferrous iron, and manganese easily interchange and substitute for each other in the A cation position, and calcium does so less readily. Additionally, aluminum, femc iron, and chromium substitute for each other to a limited extent in the B cation position. This ability to substitute or exchange ions without changing the crystal structure is called isomorphism, and garnet is one of the finest examples of a isomorphous series. Because of this isomorphism there is complete solid solution between certain garnet species but not between others. Fig. 1 illustrates these solid solution relationships. Some rare species of garnet are known that illustrate the wide range of cation substitution that the garnet crystal structure can accommodate. They include: [ ] These rare species are not of interest for industrial applications, but can be of interest to mineralogists and the gem industry. Physical Properties: Garnet displays the greatest variety of color of any industrial mineral. Garnets have been found in all colors except blue. For example, grossularite can be colorless, white, gray, yellow, yellowish green, various shades of green, brown, pink, reddish, or black. Andradite garnet can be yellow- green, green, greenish brown, orangy yellow, brown, grayish black or black. Pyrope is commonly purplish red, pinkish red, orangy red, crimson, or dark red; and almandite is deep red, brownish red, brownish black or violet-red. Spessartite garnet can be red, reddish orange, orange, yellow-brown, reddish brown, or blackish brown. A few garnets exhibit a color-change phenomenon. They are one color when viewed in natural light and another color when viewed in incandescent light. Because of the great variation in color of garnet within each species and similarities in color between garnets of different species it is recommended that garnet identification not be based on color alone. The Mohs hardness of garnet varies from 6.5 to 9.0. Grossularite and uvarovite have a hardness of 6.5 to 7.5; andradite is 6.5 to 7.0; and pyrope, almandite, and spessartite are 7.0 to 7.5 in hardness. There are reports of almandite having a hardness of between 8.0 and 9.0. As with hardness, the specific gravity of garnet varies considerably. The specific gravity may be as low as 3.2 or as high as 4.3 depending on chemical composition. Garnet crystallizes in the isometric system with rhombic dodecahedra and trapezohedra the most common forms. Crystals also form in combinations of dodecahedra and trapezohedra or either of these in combination with hexoctahedra. Crystals can have cubic or octahedral faces, but these are rare. Under favorable conditions of formation garnet will crystalize in nearly perfect forms that rival study models. Garnet also forms as irregular blebs, grains, knots, or masses, with or without distinguishable crystal faces, and as coarse- or fine-grained granular masses that appear to be totally lacking in crystal form. The fracture of garnet also shows great variation. In some garnets, particularly those that are well crystallized and glassy in appearance, the fracture is subconchoidal to conchoidal. Other, more poorly crystallized garnets exhibit a fracture that can only be described as uneven. Garnet occasionally has an indistinct dodecahedral cleavage. Certain species of garnet from specific locations have a pronounced laminated structure consisting of planes of weakness along which parting takes place. This parting may resemble cleavage, but since it is mechanical and not related to crystal structure it is not true cleavage. The optical properties of garnet are sensitive to even small changes in chemical composition or strain in the crystal structure. For this reason each species does not have a single index of re- fraction (IR) but has a range of 1Rs. Uvarovite in its pure form should have an IR of 1.870, but in nature samples vary from 1.74

Jan 1, 1994

By Debra A. Griffith

The U.S. Bureau of Mines currently is researching the relationship between the level of back strength and the probability of low-back injury. This report is a review of the literature and statistics on over-exertion injuries. Overexertion continues to be a significant source of injury in metal and nonmetal mining, accounting for approximately 24 pct of all injuries yearly. These injuries, particularly to the lower back, can be very expensive in human and monetary terms. An examination of the accident data on overexertion injuries is necessary to provide a background for research into prevention and/or amelioration of those in-juries. The job categories outlined in the Accident Data Analysis data base most affected are "Mechanic/Electrician" and "Mill/Plant Worker." The age group most affected is "30-39" years, and the experience group most affected is "0-.99" years. The most prevalent type of overexertion injury is "Strain/Sprain," and the trunk is the body part most often involved in an overexertion injury.

Jan 1, 1994

By Bharat B. Dhar, M D. Nabinllah, A J. Prakash

The study is an approach made in simulating air overpressures induced by surface blasting from those produced during gallery blasting in the laboratory, and experiments conducted on a portable window with a view to establish the sound pressure Level (SPL) for cracking of window glasspanes.

Jan 1, 1994