Search Documents

By Reha Ozel

The stability in longwall faces depends on the interaction beman the roof strata, face supports and floor strata. The load distribution on the other hand, depends upon relative stiffness of the three supporting elements namely, the coal face, support and gob. Therefore, in defining support requirements, it is particularly important to analyze the strata loading, the face convergence and the controlling mechanism provided by supports. The controlling mechanism however, depends on the type and characteristics of supports used in long- wall faces. The design guidelines presented in this paper have bean developed based on a number of strata control oriented projects carried out in Turkey, load and convergence measurements carried out in 10 longwall faces, in Zonguldak Coal Region, and procedures given in literature. Evaluation of load and convergence measurements, and analyses of face supports were carried out by means of a computer program, called L0NGWAI.L-MEW, developed by the authors. The output of the design analyses include the following: (1) estimation of support capacity for roof supports namely; individual hydraulic props, chock-type power supports and various types of shield supports, and (2) analysis of loading conditions and response of shield support components in terms of stability and structural integrity.

Jan 1, 1990

By D. A. Baker

This report describes the elemental characterization of chromite and related materials at the Bureau of Mines, Albany Research Center. Analytical methods for determining the major constituents, representing extensive experience, refinement, and development, are described and fully annotated. This presentation should allow other laboratories to use these methods and obtain comparable results with a minimum of time needed for familiarization with individual methods.

Jan 1, 1990

By A. W. Khair

This paper presents an engineering approach to solve a complex ground control problem at reduced cost, allowing the mine to be operated safely and economically. The mine has experienced serious and complicated cutter roof problem in the entries. This cutler roof problem has delayed the advance of the entry development considerably and cost of these entries is very high due to the requirement of very heavy artificial supports. The analysis includes assessment of the cause of cutter roof and step by step action taken to improve the entry condition through appropriate longwall panel entry design and roof support system. The approach for solving the problem was two-fold: 1) to apply yield pillar concept in order to reduce the effects of in-situ horizontal stress in the roof strata and 2) to find an effective way to reinforce the roof strata and to support the fractured roof and avoid caving.

Jan 1, 1990

The Barmac autogenous crushing mill is one of the most successful new comminution technologies to become available to the mining and industrial minerals industries in this decade.The Barmac autogenous crushing mill is an innovative Vertical Shaft Impactor which operates in essence like a high intensity dry ore centrifugal pump with the reduction occurring primarily as a result of high velocity rock to rock impact in a fully rock lined crushing chamber. With applications in a wide range of mining and industrial minerals operations the Barmac autogenous crushing mill presents an opportunity to enhance reduction and liberation whilst providing many cost savings and production increases in new and existing plants.This paper briefly describes the operation of the Barmac autogenous crushing mill and reviews its benefits.

Jan 1, 1990

By Deni Pageau, Deni Caron

"This paper describes the operations of the open pit and emphasizes particular aspects of Les Mines Selbaie. The open pit as well as its related services were incorporated into a complex which includes an underground mine and a concentrator. The equipment was chosen with the objective of auto-sufficiency during each phase of mining. The paper outlines the organization and the methods used in each step of mining, notably: drilling, blasting, loading, transporting and crushing. The responsibilities of the Engineering Department are also outlined from the conception of the open pit to the latest follow-up methods. A short resume of the results which have been obtained as well as suggestions for improvement are provided.Layout in Consideration of Main SiteThe A-I zone deposit is located I km from 8 zone. Open pit mining of A-I zone required the regrouping of different services to those already existing.I. The crusher was placed in an area close to the concentrator in order to minimize the length of the conveyors and to provide space for the crushed ore reserves (50000 tonnes).2. The location of the service building (warehouses, mine offices, maintenance, engineering and geology) raised a few problems. Because of the multiple services provided therein , it was impossible to fulfill all the requirements, and the garage in itself is located a fair distance from the pit. Added to this inconvenience is the fact that heavy equipment regularly travels throughout the main yard.3. The storage of explosive magazines has been changed to obtain more surface space and meet government regulations.4. A space has been provided for minor repairs in the garage used during exploration. A trailer was installed next to the garage to provide a lunch room for the employees working at the open pit."

Jan 1, 1990

By J. J. Scott

As a Rock Mechanics investigator, the author has, Over his career, attempted to use his best knowledge in developing better rock control fixtures. Based on the experience of nine years of development of friction rock stabilizers, in 1980 he decided to launch a new investigation to develop a unique roof support fixture which would fit the coal mining market. The largest single user of roof bolts in the world is the American coal mining industry, historically using up to 100 million fixtures per year. In 1989 they used approximately 82 million fixtures.

Jan 1, 1990

By R. L. Grayson, Y. J. Wang

An integrated approach to the management of underground coal mine production and cost is presented. A conceptual model for objectively analyzing an underground mine to obtain lower cost and higher productivity from operations is outlined. The model is designed to provide mine managers with a quantitative, decision-assisting methodology that can be used in formulating timely responses to fluctuations in operations. It consists of a productivity fore- cast component, routine use of current resource consumption factors, a linear programming scheduling component, a manpower loading analysis, and an inventory control component. The model is applied to an underground coal mine.

Jan 1, 1990

By Kavetsky A, Scott A

As well as breaking and moving rock, blast energy sets up a seismic wave in the ground which can cause significant damage to rock structures and buildings and disturbance to human occupants. This seismic ground vibration is potentially most damaging when its dominant frequency coincides with the resonant frequency of a structure, leading to high amplification factors between the input ground vibration and the resulting structural response. This paper outlines methods of identifying the resonant frequency of structures. It also describes a practical numerical method for the modification of blast designs to reduce the ground vibration energy in critical frequency ranges. The method is illustrated with two recent case studies.

Jan 1, 1990

By J. C. Edwards

To have the capability to predict the development of localized spontaneous heating within a porous coalbed that is subjected to forced air ventilation or in an otherwise quiescent environment in which buoyancy develops, the Bureau of Mines developed three time-dependent mathematical models, which were used to calculate the temperature increase associated with chemisorption of oxygen by the coal. In each model, spontaneous heating is driven by an Arrhenius first-order reaction between the oxygen and coal. Two models are two-dimensional, and one is one-dimensional. In the first two-dimensional model, a constant-velocity forced convection airflow is specified; and in the other, buoyant flow is allowed to develop in the absence of forced convection. The third model evaluates the airflow from Darcy's law and a specification of the pressure at the surface of a one-dimensional porous coalbed. Numerical computations demonstrated how each model could be used to predict the onset of spontaneous heating when the porous coalbed was subjected to constraints of an imposed internal heat source or a high temperature airflow. The effects of particle size and coalbed compaction upon spontaneous heating were examined with the third model.

Jan 1, 1990

By Philip L. LeHoux

In recent years, much work has been done to explain the nature of the gold-carbon adsorption mechanism. The benefits of a sound theoretical basis has the obvious application to gold adsorption and elution industrial processes. Unfortunately, the lack of a clear agreement on the mechanism has provided no clear direction towards process innovation and optimization. Jones' (1989) work has gone a long way towards clarifying the specie of gold adsorbed (and thus the chemistry required to remove it). Since the development of hot caustic and cyanide elution, the kinetics have been accelerated by the application of pressure to increase elution temperatures beyond the boiling point at atmospheric pressure. However, the traditional reagent content of 15 g/L NaOH and 5-10g/L NaCN has remained largely unchanged. This is in spite of work that has shown that the presence of cyanide is not required for the elution process to take place (Adams, 1986; Adams; 1989; Jones, 1989). Adams (1989) has also compared NaOH elution rates with and without cyanide. He found improvement with the use of cyanide and a synergistic effect with the use of both. Others have found no difference in overall extraction (Jones, 1989

Jan 1, 1990

By Sharmil Markar M

Ballarat Goldfields Limited is currently re-opening the old workings of the East Ballarat Goldfield which contain an estimated 1800 ML of groundwater. The disposal of this 'minewater' was of concern: the minewater is of moderate salinity; increased salinity levels have interfered with agriculture and water use at a number of locations downstream from Ballarat. Extensive numerical studies indicated that treated minewater could be discharged into the Ballarat Creek system for dilution by sewage effluent and by surface runoff after rainfall events. An automatic real-time salinity management system has been developed to enable the disposal of saline minewater in this fashion. A desk top computer operates the system: discharge and salinity readings are taken automatically each hour and filed away; the maximum allowable rate of discharge of treated minewater is calculated; pumps are switched on and off. The system readily enables daily, weekly and monthly data reports together with floppy disks of 'raw' data to be prepared in formats suitable for direct submission to the Victorian Environmental Protection Authority.

Jan 1, 1990

Develop methods of enhancing and measuring the high-temperature softening and melting properties of iron oxide pellets reduced under simulated blast furnace smelting conditions. Approach Add dolomite and Limestone flux and a low-cost organic binder, such as starch, carboxyl methylcellose (CMC), or waste papermill sludge, to the iron oxide concentrate to produce hematite (ferric oxide) pellets with superior high-temperature metallurgical properties. Simultaneous increases in softening temperature, gas permeability, and enhanced metallization rates are sought to improve blast furnace productivity and energy efficiency. Background In the past, bentonite, an inorganic binder, was the only additive (binder) used in the production of pellets made from iron ore concentrate. Research has shown that the reducibility of conventional (acid) pellets can be increased by the addition of flux or an organic binder. The increase in pellet reducibility results in less wustite in the center of the pellet at high temperatures, such as those obtained in the cohesive zone of the blast furnace.

Jan 1, 1990

Near Kangiara in south eastern New South Wales, Australia, a number of polymetallic (copper, lead and zinc, with minor silver and gold) mineral deposits occur within a relatively broad volcanic rock belt, intercalated with limestones, sandstones and shales, of Silurian age. The Kangiara deposit was the most significant for the region.Adjacent to the Kangiara deposit, the unaltered country rocks are more rhyolitic than elsewhere in the volcanic rock belt, and the mineralization is accompanied by silicification, chloritization, sericitization and argillization. The host rocks typically contain a higher K20:Na2O ratio than the volcanic rocks not associated with mineralization.In the Kangiara deposit the mineralization consist of massive (in part banded), fragmental, disseminated and vein-type copper-lead-zinc ores, with the massive and fragmental types divisible into pyrite-rich, chalcopyrite-rich and sphalerite-galena-rich varieties. With respect to this mineralogy, the ore textures and sulphur isotope compositions the deposit can be compared to the stratiform mineralization associated with Silurian acid volcanic rocks at Woodlawn, Captains Flat and elsewhere in the Lachlan Fold Belt, as well as the Tertiary Kuroko deposits of Japan.

Jan 1, 1990

By Bruce Vandenberg

A 3D, PC based computer program is currently under development by Blasting Analysis International, Inc., to analyze the kinetics of full scale blasts with two or more high-speed motion picture cameras.

Jan 1, 1990

By Agnes Y. Lee

As part of the U.S. Bureau of Mines program to improve base metal leach systems, pressure leaching of galena (PbS) concentrates in fluosilicic acid (H2SiF6) solution was investigated. Lead extraction was 93 pct when PbS was pressure leached in H2SiF6 at 95° C with 2OO-psig O2 pressure for 40 min, using ferric nitrate [Fe(N03)3] as a catalyst. The effects of several catalysts, O2 pressure, time, and acid concentration on leaching were determined. The purified leach solution was electrowon to recover high-purity Pb metal. The H2SiF6 used in leaching and electrowinning can be recycled continuously. A flow diagram was proposed based on this investigation. Elemental sulfur (SO) was recovered from the leach residue by solvent extraction. A method was also developed for treating the flnal residue to segregate the important byproduct elements such as Ag, Cu, and Zn and enable their recovery by standard commercial processes.

Jan 1, 1990

By Lawrence A. Taylor

The rocks and minerals of the moon will be included among the raw materials used to construct a lunar base. The lunar regolith, the fragmental material present on the surface of the Moon, is composed mostly of disaggregated rocks and minerals, but also includes glassy fragments fused together by meteorite impacts. The finer fraction (i.e., < lcm) of the regolith, the soil, is probably the most important portion of the regolith for use at a lunar base. For example, soil can be used in bulk as insulation against cosmic rays, for lunar ceramic and abodes, or for growing plants. However, beneficiation of the soil can provide other feedstocks. For example, the soil contains abundant solar-wind implanted elements, as we1 1 as various minerals, particularly oxide phases, which are of potential economic importance. These components of the soil are sources of oxygen and hydrogen for water and rocket fuel, helium for nuclear energy, and metals such as Fe, Ni, Al, Si, and Ti. The uses of the lunar materials only await a fertile imagination.

Jan 1, 1990

By R G. Richards

The Australian glass sand industry produces some 2.8 million tonnes per annum of silica sand, of which about 2.0 million tonnes are exported and the rest is for the domestic market. Approximate production rates for each Australian state are listed. The variety of processing methods used in the currently exploited deposits reflects the size, location, and characteristics of the various deposits and the requirement of the end market/s. The industry uses to a large extent equipment developed for the separation of mineral sands, particularly as it applies to low grade heavy mineral deposits, where low cost, high capacity and metallurgically efficient equipment has proved eminently suitable for the production of the low value glass sands. The requirements of the domestic market, as well as those of the present and potential export markets are discussed covering quality requirements, distribution channels and other factors critical to success.

Jan 1, 1990

By S Jackson, I Arbuthnot

The use of High Rate Thickeners has gained wide acceptance in the mineral treatment industries. The design of these units is characterized by an efficient deaeration and flocculation chamber, and introduction of the flocculated feed solids into a preformed floc bed zone. By these means the settling process is accelerated and consequently High Rate Thickeners achieve a significantly higher throughput per unit area than conventional thickeners. &nbsp; The object of a control system on a High Rate Thickener (HRT), as on a conventional thickener, is to obtain the required underflow density and overflow clarity at all feed conditions. The feed conditions which may vary include volumetric and mass feed rate, pulp density, particle size and particle type. A conventional thickener has a large volume and cross sectional area, and changes in performance occur slowly û the operator has time to observe and react to these changes to maintain control. On a HRT, there is a much reduced residence time and therefore control parameters need to be reset more frequently. Although manual control is possible, the use of automatic control systems is therefore desirable to avoid excessive operator attention, while optimizing control of density and clarity. Automatic control of a conventional thickener is usually achieved by an underflow density loop which regulates the rate of withdrawal of underflow. A turbidity meter is sometimes used to measure overflow clarity and regulate the addition of a coagulant or polymer flocculant. These measures are not adequate on a HRT, because they would not give optimum control and could lead to excessive flocculant use. To achieve optimum operation in a HRT, the floc bed level should be maintained above the feed inlet point in the thickener. This bed level has become the key variable around which most control systems have been designed. However, a number of problems have occurred which has resulted in poor control, or only partial control of thickener performance. We will describe some of these problems, and a solution which is simple and effective.

Jan 1, 1990

By S. Dawson

The Republic of South Africa has become a major producer of opencast coal in recent years. Opencast production commenced in 1970 and by 1977 some 10 million run of mine tonnes were being produced annually, Since then surface mine activity has increased to more than 60 million tonnes which represents approximately one third of the total annual South African? coal production. Whilst a substantial portion of this production is exported, the majority is used in the domestic market, The largest consumer, being the South?\ African Electricity Commission (Eskom), produces most of South Africa&apos;s electricity using coal fired power stations,

Jan 1, 1990

The Income Tax Assessment Act ["the Act"] levies tax on a taxpayer&apos;s taxable income. At a time when commerce and life were more simple, the calculation of taxable income had some connection with logic and a taxpayer&apos;s capacity to pay. However, as a result of successive governments&apos; different views of equity, their perception of avoidance, their needs for revenue and their changing views on capacity to pay, the rules determining the calculation of taxable income have continually changed to the point that logic is no longer relevant. Taxable income now is simply the product of the application of a complex set of rules.

Jan 1, 1990