Search Documents

By E. Henderson

"This paper outlines the upgrading of a double-drum 2000 hp cage hoist to provide fully-automatic operation from shaft station control panels. The application utilizes programmable controller technology to provide all necessary functions for movement of personnel and material to 22 locations in a 4000 ft shaft.Various functions involving special design considerations such as ""chairing"", ""jogging"", and three modes of ""multi-level calling service"", are outlined. The use of higher level PLC functions to optimize memory utilization and simulate ""elevator service"" required the addition of a comprehensive fault finding software section to aid in troubleshooting.This paper will deal primarily with the automation portion of the project with references made to other pertinent aspects which were prerequisite to automatic operation. It is not intended to deal with every design detail, but rather to provide an overview of what can be done in the area of automation for those considering such an application. INTRODUCTIONEarly hoisting control systems provided only the essential elements of control, leaving many responsibilities with the operator. With advancements in various areas of technology, electromechanical devices were incorporated to enforce slow-down in end zones, control acceleration rates, monitor safety devices, etc. Brake control systems were supplied to allow for ""single-stick"" operator control, regulated deceleration during emergency brake applications, etc.These additions enhanced the over-all performance but were generally confined to speed and current regulation. Some mechanical devices, such as travelling nut limits, etc.; were used to provide ""position"" control to multiple locations within the shaft. These devices, in conjunction with rather extensive relay control panels, did allow for the establislunent of some automatic cage hoists . The hoists were often limited to service from point ""A"" to point ""B""', involving a limited number of levels due to the complexities of the mechanical interfaces employed. Only limited systematic work sequences were possible . .Programmable Logic Controllers (PLCs) were introduced into industry in the mid-70s and have since gained acceptance in mining applications such as pumping, ventilation, ore handling, etc. This technology, being ""software"" based, allows complexities to reside in the program rather than increasing the number of physical control elements. This has opened the door into hoisting systems for automatic loading and hoisting of ore as well as a means to achieve a comprehensive package of automated cage hoisting functions."

Jan 1, 1989

"Mineral flotation processes are often characterized by long dead times and slow process dynamics. The process dynamics change due to different ore types, feed grades and circulating loads. These are some of the factors that can make control of flotation processes difficult. Implementation of adaptive control algorithms at Brunswick Mining has made controlling these processes feasible. The role of adaptive controllers in plant optimization and the overall control philosophy is discussed.IntroductionBrunswick Mining is located just outside of Bathurst, New Brunswick, Canada. The concentrator processes approximately 10,250 tonnes per day of ore that assays at approximately 8.9 %Zn, 3.6 %Pb, 0.3 %Cu and 100 gram/tonne of Ag. The four products produced are zinc concentrate assaying 51 %Zn, lead concentrate assaying 36 %Pb, copper concentrate assaying 21 %Cu, and a bulk concentrate assaying 32 %Zn and 18 %Pb.The original flotation process control system, supplied by Outokompu Oy of Finland, was replaced in the summer of 1988 by a Provox system supplied by Fisher Controls Inc. The Provox system consists of two redundant integrated function controllers (IFC's), two operator console stations with two screens each and a Digital Equipment Co. microVax II computer running Fisher's Computer Highway Interface Package (CHIP).In January 1989 a boiler management package, which includes the boiler control hardware and another operator's console, will be added to the Provox system. In late spring of 1989, a Vax 3200 computer running G2 artificial intelligence software from Gensym Corporation will be installed. These devices are all connected using a redundant data highway that runs around the plant.The primary measurement devices in the flotation circuit are two Courier on-stream X-ray analyzers. The Courier systems each have 14 sample cells with two streams multiplexed into each cell. Each pass of the on-stream head takes approximately 6 minutes yielding a nominal sampling interval of 12 minutes. The Courier passes its assays to its respective IFC. The IFC handles the digital and analog I/O, DDC and cascade loop control, some low level calculations and sequencing. The CHIP microVax has 9MB of memory and 220MB of mass storage running under the VMS operating system. The CHIP microVax is a central database for the Provox system. It is used for data trending, metallurgical modelling and balancing, instrumentation database, long term storage, and on-line adaptive assay control."

Jan 1, 1989

This brief overview of the history of Brown Coal mining in Victoria is a luncheon presentation -I do not intend to make it indigestible with extensive listings of resources or production. There is a vast pantry of collated historical records and of vari- ous predictive studies available for the enquired with a hearty digestion. A gourmet collation is provided in The Aus IMM Monograph No 11 published in 1984 entitled "Victoria's Brown Coal-A HUGE FORTUNE IN CHANCERY", currently still on offer by the Institute and available at a bargain price in the foyer at this conference. Monograph No 11 also provides a feast of excellent references on the theme of Victorian Brown Coal assembled by the several contributors. In contrast, my presentation paper is a fast-food service, extracts from the printed paper only-you have no choice-you "get what you get" and in small quantity. I hope it will tantalise your appetite -like Oliver Twist you will ask for more. -Buy the Monograph!

Jan 1, 1989

By A. K. Ratte, C. M. Brown

"IntroductionIn autogenous mills, grinding of the ore feed is accomplished by the direct action of the variously sized rocks making up the feed on each other and the mill interior. Size reduction is achieved without the addition of grinding media foreign to the mill feed, differing in this respect from rod, ball, and pebble milling. The term ""semi-autogenous"" has entered common usage in the industry to describe autogenous mills to which supplementary grinding ball additions are made to increase the rate at which size reduction of the mill feed occurs, beyond that achieved solely by the action of rock on rock. In a semi-autogenous grinding (SAG) mill, 50Jo to 10% of the mill volume may be occupied by grinding balls, whereas a range of 25% to 45% is more usual in ball milling.The comminution of mineral ores using ""conventional"" techniques has been described in previous papers. In conventional operations, size reduction of mined ore, and liberation of the valuable mineral content, is typically accomplished using flowsheets employing two to four stages of crushing. Crushing is followed by one to three stages of grinding and classification using various combinations of rod, ball, and pebble mills. This paper describes operations employing autogenous or semiautogenous grinding as the principal stage in the comminution process. Primary crusher discharge, or in some instances run of mine ore, is fed directly to an autogenous or semi-autogenous grinding circuit. Final product sizing may be accomplished in a single grinding stage, the mills operating in closed circuit with classification equipment, or in several stages using autogenous and semi-autogenous mills for primary grinding, and ball or pebble mills for secondary grinding. In several operations a portion of the primary mill discharge is crushed in an intermediate comminution step, these circuits being called autogenousball- crusher circuits (ABC). Many different flowsheets exist, but common and important to most are crushed ore stockpiles, reclaim feeder and mill feed conveyor systems, pumps, screens, and classifiers. Autogenous grinding is employed in both wet and dry processes, although today wet predominate."

Jan 1, 1989

By Susanne Pignolet-Brandom

Fourteen samples of crushed Duluth Complex rock were characterized by the QEM?SEM automated scanning electron microscope image analysis system to evaluate the application of the system to mining waste rock characterization. The system can reliably distinguish the iron sulfides, the copper-iron sulfides and the nickel-iron sulfides. Calcite was distinguished from all other minerals except fluorite. The volumetric abundances were verified by comparing elemental abundances calculated using the QEM"SEM volumetric percentages and appropriate mineral compositions with elemental abundances determined by standard laboratory procedure. The pH and sulfate concentrations of rinse water from laboratory leach experiments correlated well with the mineralogical data.

Jan 1, 1989

By Brian Lewis

"IntroductionThe ion exchange process is classed as a purification and concentration stage. In the uranium industry it is used to separate, and recover uranium, from a solution produced in the leach and subsequent solid washing circuit, that contains uranium as well as some impurities. The final product from this circuit is a solution, containing uranium at a 15 to 25 fold increase in concentration, with a chemical composition suitable for the ""Precipitation"" circuit.The process is a reversible chemical ""ION"" exchange, between a solution, and solid phase, with the ""resin"" being the solid phase. Various chemical changes in the solution phase will permit the resin to remove uranium from a solution or have the uranium removed from the resin back into a solution phase. The former loads uranium onto the resin, and is called the ""adsorption cycle"", and the removal or stripping is known as the ""elution cycle"".Ion Exchange resin is a semi-rigid polystyrene spherical bead, approximately 10 to 30 mesh. It is used by placing the resin in a vessel, so that a porous bed of resin is formed, through which the solution may flow.There are many different types of vessels, and systems used to hold the resin, but it is not the intention of this chapter to describe them all, but to describe two methods used in Elliot Lake. These are the ""fixed bed"", and ""moving bed"" systems, the condition of the bed during normal operation signifies the name of the system.Chemical and Physical Characteristicslon Exchange ResinThe resin used is a strange base Anionic resin, semi-rigid, and spherical in shape. The size of the wet resin is approximately 9007o between 20 and 40 mesh. Physically the beads of resin are broken early, but some have lasted over 15 years and are still in use."

Jan 1, 1989

By J. P. R. deVilliers

A procedure is described whereby gold-containing calcined concentrates and leach residues from refractory gold ores are smelted with carbon to form a small amount of metal. The gold is liberated upon smelting, and is collected in the molten metallic phase, which is easily separable from the slag. The metallic phase consists of approximately 1 to 15 per cent (by mass) of the material after smelting, and the gold content is generally upgraded by a factor of greater than 6 compared with that of the original roasted material. Recoveries better than 95% have routinely been achieved. The quenched metal contains predominant Fe-Ni alloy, as well as minor Fe sulphides and Cu-Fe sulphides. Trace amounts of Fe-Ni arsenide and Au-Cu alloy are also present. The gold content of the metallic phase can be increased further by oxidation of the hot metal in the presence of silica or slag. This will reduce the amount of metal, and will concentrate the gold in a smaller volume. The metallic phase can then be treated hydrometallurgically to recover the nickel and the gold.

Jan 1, 1989

By Vas Choudhry, Randhir Sehgal

Conventional clean coal technologies which consist of coarse coal cleaning by gravity methods and treatment of natural fines by flotation can only remove a portion of the pyritic sulfur and ash in the coal. Higher (+90%) pyritic sulfur rejection is attainable when coals are ground to ultrafine sizes to enhance liberation of the mineral matter and then cleaned. However, cleaning of coal at very fine sizes poses a number of unsolved problems, the chief one being the loss of cleaning efficiency. This, of course, means that liberation of pyrites does not always equal its rejection. In addition, the dewatering of fine- cleaned coal, and its handling, transportation, and acceptability to the utility industry a1 so pose considerable technical and economic problems, especially when compared to the FGD alternative. This paper addresses some of the critical issues involved in the cleaning of ultrafine coal s.

Jan 1, 1989

By OÆBrien D, Priddle D

In order to avoid costly moisture penalties on coal shipments and to minimise rail freight costs, screen bowl centrifuges were selected and installed in the Mount Thorley Coal Preparation Plant for dewatering fine coal product. The Mount Thorley fine coal circuit consists of desliming the -0.5 mm (ww) fine coal in two stages of classifying cyclones prior to recovery by froth flotation. Provision has been made to bypass the flotation circuit with the classified flotation feed reporting directly to product and the centrifuge dewatering circuit has been designed to handle either flotation feed or flotation product. Major mechanical failures of the gearboxes and the ceramic tiling occurred early in the operation life of the machines which led to design changes being made to achieve satisfactory operation. This paper discusses the operating experience at Mount Thorley with respect to both mechanical and metallurgical performance of the screen bowl centrifuges since their installation in 1985.

Jan 1, 1989

By A. W. de Villiers

This paper explores the behaviour of methane in the goaf during longwall mining, together with some methods for the control of methane emissions into the goaf, the working face, and the ventilation system. Experimental work done at Twistdraai Colliery, Sasol Coal, is referred to, as well as the gas-drainage system being practised at West Cliff Colliery in New South Wales, Australia. Gas drainage is discussed briefly, and certain suggestions are made in regard to coal mining in South Africa.

Jan 1, 1989

By Alberto Sarmentero

Venezuela, once a world's top gold producer until 1886 Witwatersrand discovery, did let fall its role then because of a serious lack of infrastructure and population, and lately (since World war II times), because of discouraging mining and taxation laws, laying upon an oil prizes bonanza. Recent research leading to estimates of about 5.000 mt. of gold, mainly related to the greenstone belts of the Guiana Precambrian shield outcropping in Venezuela, are opening the scope for both Government and international investing and mining companies, for gold exploration and development projects in the country. This paper overviews Venezuelan Gold mining industry, as seen from the point of view of a participating mining company.

Jan 1, 1989

By Pullen G, Rose M

Continuing Professional Development (CPD) is not just a catch-cry. It is an essential component of every-day life in many professions, including accountancy, law and public administration. Without realising it, many other professions are undertaking CPD activities in an un-structured way, including mining, metallurgy and geology. Examples include Annual and technical conferences of The Institute, Branch-level technical meetings and in-company training and development programmes and technical exchanges. Whilst approaches to date have undoubtedly helped keep the Australian mining industry at the forefront of mining technology, one cannot presume that technological development will stand still. To meet this challenge, human resource development must keep pace, not only to optimize utilization of technological developments, but more importantly to develop firm bases from which new products, processes and technologies can be developed within Australia.

Jan 1, 1989

By F. F. Aplan

"The material known as coal has a highly variable composition. As a consequence, coals show a great variation in their physical and chemical properties as a function of coal rank. The situation is further complicated because the preparation engineer must deal with raw coal, as mined. This is an assemblage of coal, upwards of 30% mineral matter and, typically, several percent pyrite. The kind and amount of the mineral constituents is also highly variable from source to source. A knowledge of coal rank and source location, and the kind and amount of associated impurities, is the first step in evaluating the response of a raw coal to preparation procedures. The raw coal must first be characterized before information from one source can be extrapolated to that of another.INTRODUCTIONCoal is a black or brownish-black combustible solid, derived from a heterogeneous mixture of plant remains and associated mineral matter that have undergone chemical and physical metamorphic changes by biological and geological processes without free access to air. It is composed principally of carbon, hydrogen and oxygen with lesser amounts of nitrogen and sulfur. 'Its exact chemical and physical nature has remained poorly defined, because the term 'coal' refers to a broad range of coalified solids ranging in rank from anthracite to a variety of bituminous coals of differing volatile matter content, sub-bituminous coals, and ending with lignite and brown coals. The variation in chemical and physical properties through these ranks is massive. In summary, Luckie's (1988) assertion is apropos: ""There is no such thing as coal; there are coals"". The coal preparation engineer, and, most especially, those scientists and engineers from other disciplines wishing to work with coal, must constantly keep this admonition in mind because what is true for one coal seam is often not directly applicable to another."

Jan 1, 1989

By A. M. Abouzeid, R. Hogg

Materials transport is involved in all phases of mineral processing. Bulk transport is necessary for moving materials between unit operations and through processing devices such as grinding mills. Differential transport is a primary mechanism for most separation processes. The basic mechanisms of transport and flow in particulate materials are reviewed and their role in materials handling and storage and in the performance of processing operations such as grinding and separation are discussed. Specific examples are used to illustrate current understanding of these transport phenomena and to indicate important research needs and opportunities.

Jan 1, 1989

By Janusz Szywacz, Bozena Bojko, Stanislaw Wasilewski

Two groups of computer programs are described in the paper. First one is the OWEN system containing software modules designed for air flow distribution analysis and prediction within the whole ventilation network of a mine. The second group is a set of programs commonly used in a routine design work connected with chosing the optimal ventilation schemes and equipment for individual areas of a mine (headings. longwall districts etc). All the programs are designed for running on the IBM PC/XT, IBM PC/AT and compatible computer systems.

Jan 1, 1989

By Joan Weinberg

Seasonally adjusted new factory orders for primary metals declined in January, February, and March, especially in the steel industry. The decline was part of an apparent slowdown for the entire manufacturing sector. Orders for all durable goods, including not only primary metals, but also clay, glass, and stone products, fabricated metal products, machinery, and transportation equipment, fell in January and February. In March, orders rose a slight 0.8%. According to the U.S. Department of Commerce, the downturns in durable goods orders in January and February were the first back-to-back declines in 3 years. They were largely attributed to a drop in orders for transportation equipment, mainly auto-mobiles and aircraft, while the small gain in March was due to a surge in aircraft orders. Higher interest rates may be partly responsible for the slowdown in durable goods orders over the past 3 months. The higher rates have also hit the construction industry--another major end-user of minerals. Construction of new homes and apartments fell by a seasonally adjusted annual rate of 5.4% in March, following a 12% decline in February.

Jan 1, 1989

By Robert L. Virta

This U.S. Bureau of Mines paper discusses the structure of the talc industry, talc production, processing of talc ore, applications and demand for talc, and the outlook for the talc industry.

Jan 1, 1989

General recognition of the potential benefits of utilizing advanced technology has focussed public attention on the organisation of tertiary education. This has produced a situation where opportunities exist for significant changes to be implemented. The challenges to Mining education in this environment of change are analysed with respect to the setting of education objectives, the role of centres of education, course structures and student access to courses. The scope of the analysis includes formal courses for professional education and technical training, and programmes for continuing education and postgraduate research. Previous significant advances in mining technology illustrate the importance of encouraging the establishment of an extensive involvement with mining education. Education cannot be the sole responsibility of professional academic organizations; significant industry participation is essential. Methods of achieving this interaction are discussed. Major changes in techniques available for disseminating information provide a significant incentive to assess the relevance of existing course structures and restrictions on student access to courses. Establishment of a less rigidly progressive system of education is discussed with respect to the development of the full potential of computer based learning. This will expand the availability of mining education to include remote locations. The practical feasibility of such changes and recognition of the value of education as a commercial resource could also increase overseas involvement in Australian mining education. Benefits of such changes and problems that may develop if accreditation systems are not also changed to take account of new technology are outlined.

Jan 1, 1989

By Nellie E. Guernsey

The Call for Papers described the session as "Top down applications; management tools for decisions, planning, investment/finance, and negotiations." In order to attract papers, and know which ones to include as well as those to reject, it was necessary to (1) define the executive suite, (2) review what had been done in previous APCOM symposia, and (3) find out what's happening now, what isn't being done, and what can be predicted. To accomplish this, especially the third task, senior managers throughout the mineral industry were generous with their time in telephone and personal interviews. Five papers were selected for presentation at the symposium and inclusion in the proceedings; the content is divided between the Executive suite in the mineral industry and those elements which apply to any Executive Suite. The Executive Suite is the top portion of the organizational tri- angle (I), those to whom the managers of functional areas such as exploration, production, finance, and marketing report. The make-up and specific activities within an executive suite reflect the organization and culture of its corporation. As there is no typical corporation, there is no typical executive suite; however, those who work within the executive suite typically do not have day to day operational responsibilities and either are, or report to, the Chief Executive Officer.

Jan 1, 1989

By D. Lenartowicz, K. R. Alexander, M Collings

Cosmo Howley is a gold deposit in the Northern Territory of Australia. The geology is complex and the input of geological data is an important part of the grade control process. As the geology of the deposit has become better understood, grade control and mining techniques have evolved to meet the changing circumstances. Present grade control depends on the use of angled blast holes, 21/2 benches and selective mining. Data is processed on site using 2 386 PC's running Surpac software. An environmental protection programme is employed, including soil stripping and stockpiling, sulphide waste containment and water quality monitoring.

Jan 1, 1989