Search Documents

By S. B. Gaidhani, V. A. Mandlekar, R. L. Sonolikar

Column flotation technique is applied for the depression of the magnetic material by the application of an axial magnetic field from chalcopyrite ore. It is observed that an increase in the intensity of magnetic field from 0 to 316.8 oersteds decreased the magnetic content in the froth from 25 to 2 %. . This might be due to retention of magnetic material in the magnetizable zone and the diffusion of nonmagnetics through it. The effect of air velocity increased the magnetic content in the froth and total froth content also. At low gas velocity the tiny bubbles are formed whereas at high gas velocity these coalesce into big bubbles and slugs formed breaks the magnetizable zone. This study opens a new field called 'Magneto-flotation'.

Jan 1, 1988

By G. E. Blight

Many mines engaged in deeplevel gold mining in South Africa are experimenting with the use of tailings fills, or are implementing tailings backfilling programmes on a limited scale. The approach varies from mine to mine, depending on circumstances and available fill materials. Several mines are backfilling with a cyclone underflow product; the cyclone overflow is then combined with the balance of the tailings stream and directed to surface disposal. As the extent of backfilling increases, the proportion of the surface tailings stream composed of overflow material will rise, and the properties of the tailings requiring surface disposal will approach those of the cyclone overflow. As the latter will be finer, less permeable and possibly weaker than the total tailings currently being disposed, the design and operation of surface tailings dams will have to be modified. Dams may have to be designed with flatter outer slopes of a reduced maximum height. Lower rates of rise may be required and, as a consequence, larger disposal areas may be demanded. To offset the negative aspects is the fact that the quantity of tailings requiring surface disposal will be reduced. The paper explores the dam-building properties of two cyclone overflow products. It shows that although these materials are inferior in dam-building characteristics to the corresponding total tailings, their geotechnical proper- ties still fall within, or close to, the range of properties typical of gold tailings. Although the design and operation of tailings dams may have to be modified, existing technology is adequate to handle these changes.

Jan 1, 1988

By T. Fujita

The removal of phosphorus is essential 1n order to increase the recycling of steelmaking slags for their manganese, iron and lime contents. This study aims at establishing the phosphorus mineralogy and its distribution in steelmaking slags, the effect of slow cooling, and the methods of phosphorus removal. A series of steelmaking slag samples was prepared at different cooling rates, and the mineralogy, chemistry and grain size of the samples were investigated with SEM/EDS and x-ray diffraction. The test results using high gradient magnetic separation are discussed.

Jan 1, 1988

By D. C. White

The Vulture Mine near Wickenburg, Arizona was a major gold producer from 1863 to 1942, having yielded about 11,000 kg Au and 8,000 kg Ag. Gold occurs as coarse native metal and electrum in quartz veins and also finely disseminated within a quartz monzonite sill and its silicified wall rock. The sill is semi-conformable within a Proterozoic volcaniclastic-dominated sequence all dipping north about 35°. Early mining focused on the vein-hosted gold particularly in the immediate hanging wall and footwall of the sill. Later efforts included some open-pitting of the outcropping sill and adjacent altered and mineralized rock. Two sets of post-mineral faults have complicated the orebody geometry.

Jan 1, 1988

By G. J. Schneider

The higher stress zone adjacent to an underground opening causes a velocity anomaly that can be mapped in favorable conditions with an acoustic cross-borehole logging system. Bureau personnel used a specialized system at the Colorado School of Mines test site near Idaho Springs, Colorado, to locate the Edgar Mine tunnel and its associated stress anomaly. Data from the logging system' were processed with a tomographic image reconstruction algorithm to map the opening and the location of the high velocity zone around the opening. The velocity imagery from tomographic analysis compared favorably with predictions from numerical modelling of the location of the stress anomaly.

Jan 1, 1988

By Thomas Rymer

Mathematical modelling of mine subsidence measured at 21 locations in Pennsylvania and northern West Virginia allows for the refinement of current methods of predicting maximum land subsidence associated with longwall coal mining. This new method (RYBAD model) is an extension of that provided by Tandanand and Powell (1984; TP Model). The RYBAD model accomplishes more accurate subsidence predictions (error typically less than 10 percent) for a greater range of mining and geological parameters through the recognition of the following: 1) subsidence increases at a decreasing rate (curvilinear relationship) with greater overburden thickness up to a critical value beyond which subsidence decreases; 2) subsidence is strongly influenced by the stratigraphic proximity of strong rocks to the coal (size of potential caving zone); and 3) subsidence index is related to overburden thickness by a family of curves, each for incremental variations in the effective percentage of strong rock in the overburden.

Jan 1, 1988

By T. G. Carter

"During the early part of the 1980s, four new surface coal mines commenced operation in the Province of British Columbia. Each represented a major investment in both persons and materials in order to protect this investment in one significant area-the fixed portion of the surface coal handling system-a substantial amount of work was undertaken to ensure that the system was well protected from an outbreak of fire. A great deal of effort in this field had already been made by those coal mines which had been in operation for a number of years and experience gained at these operations was utilized in determining the level and extent of fire protection for the new mines.This paper summarizes the major problems, and suggests some of the methods of solution, in providing an adequate degree of fire protection for surface coal handling systems. It will also discuss the potential for gas and dust explosions together with ways to minimize this potential.The Fixed Coal Handling SystemNote: The word ""fixed"" has been used in its present context to denote that part of the coal handling system where the coal is moved via fixed installations such as a conveyor. It differentiates from that part of the system where coal is moved by mobile equipment.The raw coal delivered to the truck dump will undergo two major processes on its way to the rail load out. The first will be at the coal preparation plant where coal of specified quality will be extracted from the raw feed to the plant. If this coal is of metallurgical quality, and sometimes if it is of thermal quality, it will pass through a thermal dryer where part of the moisture acquired during coal preparation will be removed, i.e. the second process. As the complexity of both the coal preparation plant and the thermal dryer is such as to warrant separate considerations they will not form part of this paper. Each of the processes, however, is generally, housed in its own building, thus, containment of any hazards is usually more attainable than those existing or caused in the rest of the system."

Jan 1, 1988

From statistics on general and electrical fatalities in the Australian mineral industry, it could be said that the present approach to industrial safety is irrational. Deaths are few and decreasing in number, yet spend- ing on occupational safety is large and increasing. State mine safety inspec- torates are being expanded and a National Occupational Health and Safety Commission was recently established. Recent data are analysed in the paper and mining industry fatalities placed in perspective with deaths in other areas. Cost effectiveness of different strategies is discussed along with social implications. Strategies found successful are described and others suggested.,

Jan 1, 1988

By Liu C. H, Juang Y. F

Coal/gas outbursts were one of the rather difficult safety problems faced in the coal mines of this Country, with coal fields characterized by frequent disturbances of folds, faults and pinch-offs. With average mining depth about 500m below surface, several such accidents occurred with up to 500 tonnes of coal outburst. In recent years, after a series of improving countermeasures had been undertaken, gas outburst accidents had been greatly decreased. The characteristics of gas outbursts in Taiwan coal mines include relating to coal petrography, mining depth and the other deformation forces. All these have been investigated, trying to determine the parameter of outbursts under natural conditions. The preventive countermeasures include predicting tests, de-stressing boring in coal seams, the emergency procedures during outbursts and certain improving options.

Jan 1, 1988

By Doris M. Hyde

The 350,000-barrel-per-day Bahamas Oil Refining Co remained closed throughout 1986. Financially troubled Charter Oil Co., joint owner of the refinery with Chevron Oil Bahamas Ltd., agreed in principle to have Chevron assume full ownership in return for canceling debts owed Chevron. Finalization of the agreement was pending at yearend. Burmah Oil Ltd. took more than a $30 million loss on the sale of its interest in South Riding Point Grand Bahama Transshipment Terminal to South Riding Point Terminal Holding Ltd.

Jan 1, 1988

The FSPE Award for Services to the Engineering Profession was awarded to Or Francis George Hill at a ceremony held in January of this year by the Federation of Societies of Professional Engineers. The following is an abridged version of the citation made by Professor A.N. Brown, President of FSPE, and of Or Hill?s reply. Achievements. It is indeed fitting that such a distinguished group of people have gathered on this special occasion to honour and pay tribute to Or Pinkey Hill

Jan 1, 1988

By M. C. van Blerck

Since its introduction in 1956, the capital allowance has been increased and its scope widened. At present the allowance is 10% in respect of two categories of gold mine (post-1973 and other deep level mines) and 6% in respect of natural oil mines. The allowance is a significant incentive encouraging the development of new mines, to the benefit of both the fiscus and the South African economy as a whole. A strong case can be made for increasing the amount and the scope of the allowance. The Margo Report recommendation that the allowance should possibly be replaced with a system of direct grants is, in theory, neutral. However, practical difficulties exist with cash grants and there is concern with the implications elsewhere in the Margo Report that the capital allowance is excessive and that, as a consequence, such direct grants will represent an effective reduction in this incentive. I believe that the best course of action would be the retention (and enhancement) of the capital allowance and the expansion of its scope.

Jan 1, 1988

By J. W. Smith, J. Van Dusen, A. Papachristodoulou

"As part of a study to evaluate factors affecting tankroom air quality, the mechanism of aerosol generation from bursting bubbles in electrowinning operations has been investigated. Typically 2 to 3 mg/m2.s are produced in zinc tankrooms. Analysis shows that the rate of production of film drops (geometric mean diameter - 2 urn] increases with decreasing bubble size, and that jet droplets (geometric mean diameter - 20 um) are not produced with gas bubble larger than - 4 mm. Both mechanisms of drop formation and current efficiency are affected by surface active agents, with an over-all reduction in emission of up to 60% to 70% being achievable. A source control system which does not adversely affect electrolyte properties is always preferred, and coalescence of all gas bubbles in to a continuous stream of gas at a single point on the electrolyte surface would eliminate aerosol emissions. This objective was the basis for design of a coalescence device which, in laboratory tests, reduced the emission rate by over 95%.The control device fit s over the electrodes in the electrowinning cell and is partially immersed in the electrolyte. A number of changes in the design which resulted in significant improvement in the performance of the device are reported.Field tests have shown that only about 75% of the aerosol below 10 um can be eliminated by coalescence. The remainder (up to 95% of the total) is controlled by coalescence of droplets, by impaction on the exposed collector surface and gravitational settling.The device does not interfere with operation of the tankroom, handles the effect of surges in power during harvesting, and is simple and inexpensive to maintain. IntroductionDuring the electrowinning of metals (such as zinc and copper) gases are evolved along the electrode surface forming small bubbles. The bubbles travel upwards and burst on the electrolyte free surface generating, in this way, small droplets. Because the electrolyte is often highly acidic or contains toxic materials, the whole process can result in the formation of an aerosol in the atmosphere above the electrowinning cells which poses a serious health hazard to workers in the area, and corrodes equipment."

Jan 1, 1988

By Diane M. Doyle-Coombs

In late July 1985, air samples from a sealed portion of the Quinland coal mine in West Virginia showed the presence of carbon monoxide (CO). Mine Safety and Health Administration (MSHA) personnel concluded that a fire was burning behind the seals. Since an imminent danger existed, the mine operator was given a closure order. The gases behind the seals were monitored and almost 2 million ff of carbon dioxide (C02) gas was pumped into the sealed area to stabilize the environment. Sixteen days after the closure order was issued, MSHA allowed the mine to return to production. Approximately 1 yr later, mine management submitted a seal breaching request to MSHA in order to drive a set of entries to further develop the mine. The Bureau of Mines established a sampling strategy and monitored gases from behind the sealed area during the breaching operation until the atmosphere was safe. This report is an account of the seal breaching conducted by the mine, MSHA, and the Bureau. The logistics of this event, the sampling strategy, and the equations applied could be used by the mining industry in future breachings or mine recovery operations. Time to reenter the area was calculated by using the methane (CH4) concentrations sampled at the discharge of the seals. Tracer gas was used to verify the ventilation flows through the area.

Jan 1, 1988

By S. Bhattacharya, M. M. Singh

The Surface Mining Control and Reclamation Act of 1977 (SMCRA) requires under-ground coal mine operations to prevent "material damage" to renewable resource lands caused by subsidence. However, what constitutes material damage is not defined. This paper discusses the applicable criteria for agricultural lands, forests and grazing lands, surface water bodies, and ground water aquifers. Although data on the subject are limited, an attempt is made to present quantitative guidelines to distinguish between moderate and severe damage due to subsidence.

Jan 1, 1988

By R. Andre, R. L. Grayson, T. Simonyi

"Results from research directed at determining the reason(s) for the ""rank factor"" in correlations between coal workers' pneumoconiosis incidence and coal seam of employment are presented. Using compliance dust samples collected from two longwall panels operating in coal seams of widely different rank, respirable particles were identified by mineral species under manual scanning electron microscope (SEM) energy dispersive x-ray (EDX) analysis and then further characterized by their physical diameter, general shape, and periphery angularity. Size fractional, mineralogical variations are presented.Of primary significance, the percentage of mineral particles from the higher rank coal seam that were uncontaminated by non-stoichiometric elements for a specific mineral species was twice that of those in the lower rank seam. The relationship held for each mineral species, including quartz. This fact may form the basis for the ""rank factor"" known to exist as well as provide a reason for the contradictory role of quartz and other minerals in previous CWP studies.An important subsequent research priority is now focusing on determining the percent¬age of all respirable dust particles that are minerals versus single-phase organic or multi-phase organic-inorganic complexes. This effort will be accomplished usingautomated SEM-EDX. The mineral purity factor will be developed further, but additional emphasis will be focused on determining the extent of inorganic inclusions in organic particles."

Jan 1, 1988

By D. F. Watson, G. M. Philip

The article cited above reflects the difficulty that is often encountered in interpreting different aspects of kriging. Baafi et al. write: "Due to negative kriging weights, negative block grades may be obtained in some extreme situations, which makes no practical sense." Their solution to this particular problem is to constrain the kriged estimates to data values that have positive weights, i.e., reduce the subset size contributing to the estimation. As Journel (1986, p. 133) has already observed, "Negative weights are no evil." Indeed, they are an ineluctable result of the Lagrangian multipliers in the system of simultaneous equations. The fact that data distant from the estimation point may be given negative weights simply means that the influence of such distant values must be negated because their influence is contradictory to closer values (as illustrated by Baafi et al. in their Figs. 3 and 4). Of course negative kriging weights applied to distant grade values will not in themselves induce negative grade at some central interpolation point. Negative grade values, rather, seem to be a particular artifact of automatic methods of estimation involving accumulations (Philip and Watson, 1985a, 1985b, 1987b). The elimination of negative weights, suggested by Baafi et al., is likely to exacerbate a quite different problem of kriging and piecewise spline interpolation discussed elsewhere (Philip and Watson, 1987a). In interpolating large data sets of scattered observations, changing local subsets or neighborhoods must be selected automatically. Because of the mathematical formulation of kriging and spline interpolation, discontinuities then occur between closely-spaced estimation points as the subset used in the estimation changes. If this subset is reduced in number and size, the discontinuities will be amplified and more common.

Jan 1, 1988

By Barry Welch, Kai Grjotheim

"The capital intensive nature of the present process for aluminium smelting, the low productivity per unit reactor, and pressure to reduce the electdcal energy demand have motivated the search for an alternative process. Optional routes include carbo-thennal reduction of alumina (using an alloy phase immediate), chlorination followed by electrolysis of aluminium chloride, and electrolytic decomposition of alumina using inert electrodes. Materials performance and reactor design constraints have been a major limitation for alternatives. However parallel research has led to considerable advances in the process efficiencies and scale of both the Bayer process and the Hall-Heroult cells.Future development of alternatives is dependent on breakthroughs in Materials Science such as the development of stable conducting anodes and stable wettable cathode materials. However if successful it is probable that some spin-offs will be retrofitted to existing cells. Therefore the basic Hall-Heroult technology will continue as the dominant process for at least the next half century.IntroductionThe present Bayer/Hall-Heroult process for production of aluminium is just over 100 years old. Frequently, during the century of its technological development questions have been raised as to whether it is the ideal route for metal production. The questioning was particularly intense in the period between the mid-1950s and the mid-1060s when the limitations of the Hall-Heroult electrolytic stage were evident. Then the cells were only 30 to 35 % efficient with respect to the utilisation of the hydro-electricity (requiring 16 18 kWh/kg, thus making it strongly dependent on cheap electrical energy), while the size of cells being installed were 80 to 130 kA. Hence the process was capital intensive, the productivity per reactor volume low, and the process was labour intensive (requiring about 15 man hours per tonne of aluminium). In addition, the use of pitches for Soderberg anodes and the fluoride electrolyte were creating problems through emission. At that time material science had paid little attention to the manufacture and use of carbonaceous materials or the development of alternatives that were corrosion resistant to cryolite or liquid aluminium. Hence cell lives were short - typically 600 to 1000 days - thus adding to operating costs. Thus the grass over the fence, as foreseen in 1960s vintage crystal balls appeared much greener for alternative processes."

Jan 1, 1988

By W A. van der Westhuizen, Beukes G. J, Vermaak J. J

Large parts of the arid northern Cape Province South Africa are blanketed by Quaternary cal- crete under which potential base-metal ore- deposits may occur. In an attempt to examine the nature of the distribution of such ore-re- lated elements in a calcrete environment, calcrete and soil samples from the copper-nic- kel prospect at Jacomynspan and the copper- zinc deposit at Copperton were examined. Both deposits form part of the Namaqua mobile belt. CALCRETE GENESIS In Southern Africa calcrete is restricted mainly to the western two-thirds of the sub-continent, south of the latitude 17¦ S. Various models have been put forward to explain calcrete genesis and Goudie (1973) and Netterberg (1969a) give detailed discussions on this topic. The most popular model for calcrete genesis is one of pedogenic origin. McPherson (1979), Watts (1980), Wright (1982), Arakel (1982), Netterberg (1969a), Goudie (1973) and Multer and Hoffmeister (1968), amongst others, support the hypothesis of calcrete formation by carbonate precipitation from downward percolating calcium carbonate rich soil waters. Calcium carbonate is usually initially precipitated as nodules or grains which can develop to form more compact layers.

Jan 1, 1988

By Guenter F. Lehmann

This report summarizes the results of the development and testing of a prototype monorail suspended bridge conveyor (MBC) system as a method of continuous haulage In underground mining applications. Included are the results of full scale, surface and underground testing of the complete MBC system. Conclusions drawn from these results, together with recommended modifications, supports the viability of the MBC system.

Jan 1, 1988