Search Documents

By Larry A. Haas

A major problem encountered in dump leaching operations is the plugging of both the dump and the piping by precipitated iron compounds. Bureau of Mines research to obtain basic data on agitation leaching and dump leaching methods has shown that the addition of organic chelating reagents can significantly enhance the lixiviant permeability through the ore and the concentration of the metal values in the liquor. For example, the addition of 5 giL citric acid (CA) to a conventional sulfuric acid lixiviant almost doubled the fluid flow rate through 5-cm-diameter laboratory columns containing copper ore. After 185 h of per-colation leaching, the metal concentrations with (and without, in parentheses) CA were 1.7 (1.5) giL Cu, 200 (70) ppm Mn, 160 (40) ppm AI, and 6 (3) ppm Co. The enhancement of metal concentrations with chelating reagents such as CA was confirmed by determining the solubil-ity of several metal ions as functions of pH and chelating reagent con-centration. When ferric ions became insoluble at pH values above 3, the concentrations of other ions also decreased. The addition of che-lating reagents kept iron, as well as the other dissolved metals, in solution even at pH values as high as 5. Citric acid was a more effective chelating reagent than gluconic acid, oxalic acid, or sodium lignin sulfonate.

Jan 1, 1985

By U. W. Lisner, V. J. Hucka

Coal, which was discovered in Utah in 1849, covers about 18% of the total area. Production in 1981 was more than 13 Mt (14 million st). However, some Utah coal mines are quite gassy. If longwall face technology is applied, then release of a large volume of methane may be expected during the mining process. Investigations on methane content have been made by use of an isothermic bubble desorbometer. A desorbable methane content of 0.5 to 16 m3/t (20 to 632 cu ft per st) of coal has been determined.

Jan 1, 1985

By Donald R. Fosnacht

An investigation was initiated to obtain the scope of the problems associated with recycling various waste oxide materials generated at Inland Steel and to identify and? test techniques that could possibly aid in increasing the amount of waste oxide materials recycled to primary. operations. Based on the results of this work, several new techniques were developed ?and tested on ?a plant or laboratory scale. These include the use of cold-bond agglomeration methods for producing waste oxide agglomerates for use as a cooling agent or scrap substitute in steelmaking operations, and the use of various techniques for beneficiating blast furnace flue dust and soaking pit rubble so that the upgraded materials can be utilized in sinter plant or ironmaking operations. The physical and chemical characteristics of the waste oxide materials and the results of the laboratory and plant testing are discussed in this paper.

Jan 1, 1985

By Brian E. Davies, Bobby G. Wixson

INTRODUCTION The mining, extraction and refining of metals into useful materials is an honorable profession with an ancient and productive history. Civilizations have long depended upon metals for their implements, structures and machinery necessary for survival, growth, and development. Today, as in the future, metals and minerals are essential to the progress of mankind as we approach the 21st century with technologies and concepts that will require new concepts and production from the metal mining and processing industries. Today is the tomorrow we talked about yesterday and the implementation of new ideas is essential if we are to achieve "Frontier Technology in Mineral Processing". Unfortunately, the state-of-the-art mining, processing, smelting and refining methods historically employed were less than desirable environmentally, which has caused todays public to view the metal mining and processing industry with concern. Presently the ancient rock and chat tips connected with old Roman lead-zinc mines which were worked in Wales are causing stream contamination problems that must be corrected at considerable expense to the local governmental agencies (Firth, J.N.M., et al., 1981). However, improved progress has been made and the environmental control and clean-up procedures utilized by modern lead-zinc operations in the "Viburnum Trend" or "New Lead Belt" of South East Missouri may serve as a model to illustrate how alternative technologies, environmental concerns and cooperative efforts contribute to efficient mineral production within the confines of a U.S. National Forest region without significant environmental impacts. This area received international attention when it was opened within the boundaries of the Clark National Forest in the mid 1960's. By 1970 it ranked first in the world by producing 432,576 short tons of lead ore and has since continued in this position producing 451,153 short tons of lead ore in 1983 representing 91% of the total United States lead production (U.S. Bureau of idines, 1983). This production comes from a mining area approximately 40 miles long by 10 miles wide extending in a north-south direction. Geologically the lead is disseminated throughout the Cambrain age Bonneterre Formation, mostly a dolomite, at depths ranging from 700 to 1200 ft. (213.4 to 365.8 m). Galena (lead) is the principal ore mined with lesser quantities of sphalerite (zinc), chaleopyrite (copper) and silver being recovered as economic co-products. This new mining development in one of Missouri is most scenic areas could have led to a classic confrontation between industries and environmentalists. Instead, through the cooperation of industries, governmental agencies and university researchers, the Ozark environment has been protected, and may serve as a model for future coexistence of the mineral industry with the environment. Cooperative Program Development As early as 1965 five new mines and two lead smelters were being prepared for production and environmental concern was an essential part of that planning. All the mining companies became acquainted with representatives of the various federal and state agencies and scientists from the University of Missouri-Rolla (UMR). During the next six years, St. Joe Minerals Corporation, American Metal Climax, Inc., Cominco American Incorporated, Ozark Lead Company (Kennecott) and American Smelting and Refining Company participated in cooperative research efforts. The companies also participated in information exchange meetings, the development of improved analytical methods and the utilization of research findings in the modification or construction of pollution-abatement facilities. Early on research was carried out to determine background values and to establish natural baselines of trace metals in the surrounding environment. The unusual topography and drainage pattern of the mining area were helpful since it was possible to establish control sites and test sites below individual mine-mill operations to study waste-water effects on the receiving streams. The location of the ‘New Lead Belt', mines, mills,

Jan 1, 1985

The title of my address today 'An Environment for Mineral Development' is a play on words, but I wish to use the meaning of the word environment in the broadest possible context to comment on those factors that control mineral development in New Zealand today. Of prime importance, let us consider the current economic environment in which New Zealanders live and work, as individuals and communities, and as a trading nation. It is the expanding growth requirements of the emerging nations and the interactive economic forces of our international trading partners and competitors, that dictates New Zealand's economic environment and thus the priority to develop its natural resources. As an itinerant New Zealander who has kept a watching brief over the economic environment in New Zealand over the last 30 years, I say, without prejudice, that I am concerned to have seen New Zealand's external and internal trading position deteriorate so rapidly in the last decade. I am concerned that a significant proportion of the population has been extremely slow to realize that with the creation of the European Economic Community, in the late 1950s, and following the first OPEC oil crisis in 1973, New Zealand in a corporate sense came close to technical bankruptcy.

Jan 1, 1985

The Australian lead-zinc industry faces a future in which the world market is likely to show at best only minimal growth and in which there will be increasing competition. Its production facilities use mature technologies employing expensive labour and increasingly costly energy in a country which demands the highest standards of environmental performance. Returns on investment are already unsatisfactory.Technology for survival would appear to indicate a need not only for more efficient capital, labour and energy usage combined with improved environmental performance, but also flexibility to handle more complex materials than the traditional, virtually single metal concentrates. This offers the potential for improved overall economics from the mine onwards, but will demand efficient separation and by-product recovery processes.In the lead industry these problems are being addressed in several emerging technologies. With zinc, the situation is less clear.

Jan 1, 1985

By Barbara H. Carroll

In order to rapidly evaluate an area for its mineral potential, a reconnaissance exploration program generally includes the following: 1. Outlining an area of interest 2. Identifying known mineral deposits 3. Bibliographic search of the literature 4. Evaluation of geochemical and geophysical surveys 5. Compilation and review of geologic maps The information now available from various government agencies regarding the mineral deposits, geology, and geochemistry may be integrated and used as a tool to rapidly evaluate an area before the field season. The databases most commonly used in the United States are the USBM MAS/HILS system and the USGS MRDS system for their information on mineral deposits; GEOREF and GEOARCHIVE for bibliographic information; and NURE data for the geochemistry and geophysics. In conjunction with the project geologist, this information may be used to plot known deposits and their geochemical signature as well as any other areas of like signature for further examination.

Jan 1, 1985

By M. E. Gershon

Conventional methods of drill hole site selection are reviewed briefly. Two approaches using geostatistics are then discussed, both of which have been shown to yield improved results. Finally, a branch and bound algorithm is described which will select the best locations for drilling from a user specified number of possible drill sites. Two options are discussed. First, the user can specify a maximum drilling investment or a maximum number of drill holes and the program will select the locations yielding the minimum estimation variance. This amounts to getting the most for a given investment. Alternatively, a maximum tolerable estimation variance can be specified and the program will select the number and location of the drill holes to obtain the desired information at a minimum cost. Another benefit of the approach is the quantification of the tradeoffs between investment and information obtained.

Jan 1, 1985

By V. Rajaram

A mine fire or roof collapse may necessitate the reversal of main fans to isolate the fire or provide an escapeway. Hence, to assist the mine operator in estimating the flow and pressure during reversal, Engineers International, Inc. conducted a laboratory and field study of the reverse performance characteristics of main mine fans. Laboratory tests were performed using a 96-inch (2.4 m) diameter vane axial fan to establish the forward and reverse performance characteristics under controlled conditions. Subsequently, a field test was conducted in a Colorado oil shale mine during which two 79-inch (2 m) diameter fans were reversed. The data obtained indicate that reverse performance characteristics are dependent upon the blade angle and the hub to tip ratio. The quantity in the reverse mode ranged from 30 to 65% less than in the forward mode, and the static pressure was directly proportional to the square of the quantity.

Jan 1, 1985

To develop a reliable, remotely-controlled, mobile roof support to eliminate the need to set posts, cribs, or props while extracting coal pillars. Approach The primary danger during pillar extraction is premature caving of the mine roof. The roof must cave predictably and dependably to ensure the safety of miners. Support during retreat mining is usually obtained by setting posts, cribs, props, roof bolts, or a combination of these devices. These are set manually by miners in the working area. To help minimize the danger to mine workers and to equipment posed by premature falls, the Bureau of Mines developed the mobile roof support (MRS) system to secure the roof during pillar extraction. How It Works The Mobile Roof Support (MRS) is eight-feet-wide, ten-feet-long and five-feet-high, with twelve inches of ground clearance. It is ruggedly built and exerts less than 20 psi ground pressure. The MRS is powered by a 40-hp, 460-v AC permissible motor. The reversible, variable tram speed is 80 ft/min on a 20-percent grade. It is tire-mounted, has a trailing cable, and is remotely controlled either by a radio or a tether communication cable. The machine carries four 50-ton jacks which serve as props for working heights from seven to fifteen feet. Two jacks are chassis-mounted and two are on swing arms. Each jack has a cap which distributes the roof load to three paints. The swing jacks form a breaker row to stop falling roof and prevent caving Into the work area. One jack has a visual load indicator and a second is wired to the machine lighting system. Blinking lights indicate when the preset loading is being exceeded. In the case of excessive loads, an ability to remotely jettison either or both swing jacks has been incorporated into the system to permit removal of the MRS while the roof is still supported.

Jan 1, 1985

By H. D. Peterson, G. E. Butts, J. F. Spisak

In 1978, Anschutz Mining Corp. began efforts to develop the Madison Cobalt Project in southeast Missouri. Preliminary metallurgical studies indicated that intermediate grade cobalt products, suitable for shipment to existing refineries, could be recovered from the sulfide mineralization of the ore body. However, tolling and freight charges were significant, as the refineries were located outside the US. These refineries would not satisfy the goal of strategically insulated production of superalloy-grade cobalt. The acquisition of proven, readily available refinery technologies was then evaluated. However, licensing costs were substantial and the "proven" technologies were not directly applicable to the unique chemistry of Madison materials. Faced with these challenges, Anschutz, in conjunction with the Colorado School of Mines Research Institute, embarked on an effort to develop a sulfate-based separation and refining process. CSMRI performed bench-scale and continuous pilot experiments on solutions generated through other pilot campaigns conducted by Lurgi, Hazen Research, and Sherritt Gordon. The results indicated that cobalt could be selectively extracted from sulfate media using a new generation of organophosphates. The solvent extraction system produced a solution suitable for electrolysis of high-purity cobalt. Preliminary cost studies indicated the novel process was competitive with other refinery systems. Plans to develop the detailed engineering-design information required to commercialize the process were abandoned when the price of cobalt collapsed to less than $17.64/kg ($8.00 per lb).

Jan 1, 1985

By Christopher M. St. John, Tony F. Zahrah

Empirical and numerical methods are the two extremes of the tools available for the seismic design of subsurface excavations and underground structures. Both have their limitations: when relying on purely empirical methods directly relevant experience may be scant; site data may be insufficient to justify a comprehensive dynamic analysis. The primary purpose of this paper is to review the analytical tools available to the design engineer of subsurface excavations and underground structures. Particular attention is devoted to simplifed models that appear to be applicable in many practical cases.

Jan 1, 1985

By Donald E. Graham

A mineral survey of a 12,350-acre portion of the 13,150-acre Juniper Creek Wilderness Study Area (WSA) in southwestern Idaho was conducted by the U.S. Bureau of Mines in 1984. The area is entirely underlain by thick flows of Banbury Basalt. Rhyolitic tuff of Little Jacks Creek is exposed in the walls of the Owyhee River canyon beneath the basalt. Minor units of lacustrine sediment occur between the volcanic layers. No mines or claims occur in the area, and no mineralized zones were found. The study area is covered by oil and gas leases or lease applications; there has been no known exploration.

Jan 1, 1985

By G. Barbery

A review is given of the present applications of random sets and integral geometry in fragmentation and liberation models of ores and minerals. Although attempts have ben made in the past to apply such mathematical techniques to the comminution of solids, it is shown that it would not result in major progress. In liberation modelling, it is demonstrated that the approach can lead to fruitful results. Following a recent paper by Davy (1984), a model of liberation prediction is developped, which can be calibrated far ore texture and breakage using image analyzers. The model is demonstrated for the case of a Poisson polyhedra ore texture and monodisperse fragment size. The model enables to predict the complete composite particle distribution, and is thus valuable for integration of ore breakage models with minerals separation models.

Jan 1, 1985

By L. M. Falcon

Cassiterite is considered to be the only economically significant tin mineral in the earth's crust, and in its purest form has a tin content of 78,6 per cent. South Africa has limited deposits of the mineral, and by its exploitation contributes about 2 per cent of the world's production. This paper gives a brief history of tin mining in South Africa, which dates back almost 3000 years. Over the intervening years, many tin-mining operations have flourished and as quickly disappeared. At present there are only three tin mines in operation, and a description is given of the methods of mining, concentrating, and smelting that are used. The properties and uses of tin are listed, together with relevant statistics.

Jan 1, 1985

By S. R. Titley

Carbonate-hosted massive sulfide (60%) ores of the western Cordillera compose a distinct class of deposits although they vary widely in detail and perhaps genesis. They have been important sources of lead, zinc, copper, silver, gold, and more rarely, molybdenum, tin, and tungsten in complex mineral assemblages usually dominated by pyrite. They occur as concordant stratiform bodies, as discordant mantos, and as chimneys crossing tens of meters of section; many are associated with faults and breccia bodies. Environments of formation of carbonate hosts range from craton basin to shelf with ages from Proterozoic to Cretaceous; in many instances, dating has shown mineralization to be significantly younger than hosts. Temperatures of formation determined for many deposits are high (200°-400°) and many districts are centers of igneous activity manifested by dikes, sills, and stocks. However, direct cause and effect relationships have been difficult to establish. Many important problems attend the renewed interest and study of these deposits and include questions of metal-sulfur sources, metallization processes and histories, geological controls at all scales, and relationships to broader patterns of metallogeny.

Jan 1, 1985

By R. J. Weigel

The Santa Fe Railway serves the dominant U. S. potash producing region which is centered at Carlsbad, NM. This rail system extends over 12,000 miles stretching from Chicago to the Texas Gulf Coast to the state of California. (see Figure 1) Since Carlsbad mining operations began in the 1930?s, Santa Fe has been transporting potash to many of the important grain producing areas of the country and to the major ports in Texas and California. Santa Fe has maintained a close relationship with the potash companies and has adopted a marketing philosophy of attempting to maximize opportunities for the Carlsbad producers where it is mutually beneficial. Potash has been an important commodity for the Santa Fe. It accounted for 8% of our revenue in 1965 and 3% in 1984. In the 1950?s, Carlsbad became the second largest revenue producing point on the Santa Fe. But this prominent position has diminished as ore reserves became depleted, imports flooded the U. S. market, and truck transportation developed.

Jan 1, 1985

By S. S. M. Chan

The Bureau of Mines has investigated the structural aspects of shafts and support systems using the finite-element technique. In situ field measurements in deep, vein-type metal mines show that rock stresses are often higher in the horizontal direction than the vertical, and unequal in the horizontal plane. These data and laboratory and field-determined physical properties were used as input to analytical studies. Various design and construction parameters were investigated to deter-mine the effect on shaft stability. Rectangular shafts were studied in detail to determine the effects of applied stress ratio, shaft orientation and dimension, influence of interbedded quartzite and argillite, and rock fracturing. Various support systems were analyzed, including concrete lining, timber, and steel sets. Circular configurations were investigated to evaluate yield zones and liner thickness. Elliptical shafts and time effects were briefly evaluated to illustrate shape and time effects and demonstrate the methodology. It is shown that the magnitude, direction, and ratio of applied stress and rock mass anisotropy are keys to determining shaft stability. A realistic conceptual framework was developed with which to examine the rock and support interaction in deep mine shafts. Structural analysis techniques overcome some of the historical difficulties with shaft de-sign by defining the field data requirements and structural sensitivity of various design and construction parameters.

Jan 1, 1985

By David G. Adam

Syncrude Canada Ltd. is currently mining over 120 million tons per year of overburden and oil sands to produce 40 million barrels per year of synthetic crude oil. Production increases are planned. This paper reviews the technical and economic assessments of feeder breaker applications in both ore and waste mining which led to an extensive testing and development program and finally to the procurement of full scale production equipment.

Jan 1, 1985

By R. K. Singhal

In an underground coal mining environment, a frictional ignition may be defined as the ignition of an explosive air/ methane/coal dust mixture by mining machinery. As the use of power loading equipment has become more widespread, frictional ignition incidents have increased. There have been many fatalities and injuries from this cause including the death of eleven miners in Sydney coalfield of Nova Scotia, Canada in 1979. This paper reports on the findings of a preliminary study carried out under the auspices of the Coal Research Laboratories, Department of Energy, Mines and Resources Canada. The objective of this study has been to identify a Longwall face cutting system that is inherently safer than the conventional shearer loaders used in Nova Scotia.

Jan 1, 1985