Search Documents

By Richard J. Goff

Technical Support, one of several major organizational units in the Mine Safety and Health Administration, provides technical assistance to the mining community in all areas of health and safety. One of its many areas of expertise is noise control. Depending upon the needs of the operator or inspector, the services provided can range from locating major noise sources to actually building noise controls. Over the years a vast amount of knowledge has been obtained as to what will work and what will not. DESIGN GOALS While many noise controls have been developed for mining equipment and operations, the most acceptable (ergo successful) have achieved the following design goals: - a noise level reduction of at least 5 decibels; - minimum interference with production; - inexpensive to install; and - effective in reducing low frequency noise.

Jan 1, 1984

By Swapan Bhattacharya

Section 516 of Public Law (PL) 95-87, commonly known as the Surface Mining Control and Reclamation Act of 1977 (SMCRA), requires that underground coal mine operators must 'adopt measures consistent with known technology in order to prevent subsidence causing material damage to the ex- tent technologically and economically feasible, maximize mine stability, and maintain the value and reasonable foreseeable use of such surface lands, except in those instances where the mining technology used requires planned subsidence in a predict- able and controlled manner..." Implied in the constraints of Section 516 (b) (1 of SMCRA is a determination of what constitutes "material damage" to surface structures and renewable resource lands, and the capacity for sequential land use following underground mining. This Study was undertaken in an attempt to provide quantitative guidelines for estimating material damage to a wide variety of surface structures and renewable resource lands. Surface structures studied included buildings, bridges, railroads, highways. pipe- lines, d~, embankments, and water reservoirs. Damage criteria for buildings developed in this study along with details of the adopted methodology have been presented elsewhere (Bhattacharya et al.) (1). and will not be repeated here. Similar guidelines for renewable resource lands have also been discussed (Singh and Bhattacharya) (2)

Jan 1, 1984

"At a current mining rate of 3,750 tons per day, La Mine Doyon is currently the largest gold mine in Canada. La Mine Doyon is an open pit gold mine located in the Abitibi area of Northwestern Quebec. The project is a joint venture between Soquem, a Quebec Crown Corporation in the resource development field and Lac Minerals Ltd., a publicly-held, resource development company. Lac Minerals is the managing company and operator of the project.Doyon went into production in 1980 on a very limited basis at 600 tons/day, and has seen a step wise increase to the current rate of 3,750 tons/day. Initially, all the ore was processed at Noranda Mines, Horne Division as flux for the copper smelter. The East Malartic Mill in Malartic was then upgraded and began processing Doyon ore. The third step in the progressive increase of throughput was the commissioning of the Doyon mill in November of 1982. Doyon ore is currently being processed at all three locations.During 1983, an exploration ramp was driven to explore the ore below the ultimate pit depth. Current plans indicate the sinking of a shaft and the commencement of underground mining during the next 2 or 3 years.Since its humble beginning, La Mine Doyon has always been a success; ore reserves have been extended to the east and the west and will soon be confirmed at depth, the mining and processing rates have been increased 6 fold, and the recovery has been increased from a designed recovery of 85% to over 95%. The intent of this paper is to trace the history and reasons for these rather dramatic improvements."

Jan 1, 1984

By Richard J. Mainiero

INTRODUCTION Because of the hazards associated with flammable methane gas and coal dust, the shooting of mudcaps (adobes) or other unconfined explosive charges in underground bituminous coal mines is prohibited; all explosives must be fired in stemmed boreholes. However, there are situations where it would be advantageous from a safety standpoint to fire open shots. This would be in the areas of dislodging loose roof slabs, overhangs, rock-fall leveling, slab or boulder breaking, crib removal, and crevice shooting. The Bureau of Mines, U.S. Department of the Interior, has been developing an explosive charge that is non-incendive; that is, detonation of the charge will not ignite a flammable atmosphere. This explosive charge could be applied to the blasting conditions mentioned above. As of this writing, the explosive charge has not yet been certified as "permissible" for use in flammable atmospheres, but the necessary protocol is being finalized with the Mine Safety and Health Administration (MSHA), U.S. Department of Labor. The explosive charge described in this paper is merely a prototype sheathed rock-breaker charge (sheathed permissible explosive rock- breaker charge) demonstrating the feasibility of such a device. Industry may modify the design and composition of the charge in producing a commercial product so long as it is still safe, as defined by a testing schedule being developed by the Bureau of Mines and MSHA.

Jan 1, 1984

The Knelson Concentrator is a centrifugal gold concentrator developed in Canada, which utilises the combination of high gravitational ("G") forces and a unique fluidising action to efficiently recover free gold particles from minus 6 mm to fine micron gold in both alluvial and hardrock applications.Operating parameters including water requirements, fluidising pressures and feed rates are given, as well as an indication of their various effects on gold recovery.Results include a Colorado School of Mines Research Institute (CSMRI) report comparing the Knelson concentrator with various other gravity concentrators.

Jan 1, 1984

By E. H. Ahrens

This paper deals with the responsibilities of an operating geologists and the relationship of operations to exploration. It should be of interest to those soon to enter the profession, those new to mining geology and as a review to more experienced geologists. Subjects discussed include detailed geologic mapping, sampling, core logging, assaying, selection of proper map scale, posting geological and assay data, section preparation, identification of ore controls, delineation of development drill targets and geologic hazards, models and the very important topic of salesmanship. Methods and ideas, proven valid in vein, pyrometasomatic replacement and porphyry copper deposits are presented. Hopefully, these will smooth the path for new members of our profession.

Jan 1, 1984

By Alf Holmelid

Until recently the only automatic control of electric parameters in submerged-arc furnaces has been electrode control with electrode current or electrode impendance as controlled variables. Elkem Research and Development Centre has delivered this kind of control for a long time, both stand- alone controllers and control algorithms incorporated in an integrated computer control system. In recent years we have noticed increasing interest in more sophisticated electric control. Results both from pilot-plant experiments and from production furnaces show that proper electric conditions in the furnace are more important to the furnace operation than was assumed earlier. Optimal electric conditions lead to lower power consumption per ton of metal and allow use of cheaper raw materials Besides, power contracts and the market situation lead to more frequent change of load on the furnaces. Therefore it is important to vary the load in a way that allows proper electric conditions to be maintained. Based on this renewed interest in electric control, Elkem Research and Development Centre has carried out a project, starting with analysis of existing electric instrumentation and control algorithms for electrode control, and ending up with an integrated electric control strategy including power-demand control as shown in Figure 1. In this paper we will give a resume of this work and present a new integrated control strategy put into operation for the first time in June 1983. [ ]

Jan 1, 1984

By Denholm WT

The main objective of the experimental study was to investigate the dissolution kinetics of various forms of carbon under iron bath converting or smelting-reduction conditions, i.e., particulate, free moving carbon in contact with a turbulent iron melt. Iron/carbon melts were contained in cast magnesia-lined silicon carbide crucibles heated by a medium frequency induction furnace. The melts were stirred by injecting nitrogen through 2 mm I.D. alumina lances submerged to a depth of 50 mm in the 100 mm deep baths. Particulate carbon in the form of graphite, brown coal char and petroleum coke, were dropped directly onto the turbulent bath. The dissolution rates of the various carbon types were monitored by taking periodic bath samples for subsequent carbon analyses. The effect of carbon particle size (1-6.25 mm), the degree of bath turbulence (nitrogen stirring rates of 0-20 litres/min), and bath temperature (1300-1500¦C) were assessed. The analysis of the results was complicated by particle buoyancy effects, but it was established that the dissolution rates of the three carbon types investigated were similar, and increased linearly with increases in the gas stirring power inputs. Particle size had relatively little effect on the dissolution rates.

Jan 1, 1984

By Adrian Brown

The primary method of slope stabilization is ground water-control. Recent research has established the properties which slope materials must exhibit in order for stabilization measures to be feasible, but there is little guidance in the literature about suitable field tests to develop the parameters needed for this evaluation. This paper presents a proven method for large scale testing which allows an evaluation of the feasibility of ground water pressure control in a reasonable cost and time frame. Methods of performance and analysis of the test are presented, and the method is illustrated by reference to case examples.

Jan 1, 1984

By Kinsella B

Titrimetric studies have been carried out on the activated carbons Kintal 1105, Norit 2520 and Kuraray 2GA. Titration curves of the carbons before and after acid and water washing and gold loading indicate that the acid-base properties of the carbons are affected by both the method of treatment and also by the loading of gold. It is considered that the pKa values of the functional groups on the carbon surface are in the regions of 11, 7 and 3 respectively.

Jan 1, 1984

By William J. Rothschild

Ground water at construction sites can be controlled by properly placed wellpoint dewatering systems. Care must be taken in planning cofferdams to have adequate space for and access to pumps, headers and the points. A most important part of dewatering is protection of adjacent structures from movement. A checklist gives items to consider in bidding.

Jan 1, 1984

By Jameel Menashi

Aqueous solutions of Na2Cr04 can be reduced with CO to produce hydrous Cr203 and NaHCO3/Na2CO3. CH3OH, HCOO and HCHO in the presence of CO2 also reduce Cr 6+ and yield similar products. It is shown that the rate of Cr6+ reduction can be represented by the expression -d[Cr6+]/dt=k[Cr6+)1/2[R] where [R] is the aqueous phase concentration of CH3OH, HCOO- or CO. With these three reductants, the activation energies for the reduction processes are comparable and are of the order of 100 kJ/mole. Rapid reduction rates are attained at temperatures in excess of 220°C and, with these three reductants, a green acid-insoluble readily filterable hydrous Cr203 is formed. With HCHO significant reduction of Cr6+ occurs at about 80-100°C and an acid-soluble violet modification of hydrous Cr2O3 is formed. The reduction process is reasonably selective: solutions of Na2CrO4 contaminated with Mo6+ and W6+ can be reduced to yield a Cr2O3 product with significantly reduced contaminant levels. These findings are utilized as a basis for a process for recovering chromium from secondary source materials.

Jan 1, 1984

By Howard E. Banta

From Alaska to Florida and California to Maine, the National Forest System (NFS) is host to unprecedented levels of prospecting and development. The NFS is large (191 million acres), geologically attractive from the mineral standpoint and relatively unexplored. Significant recent finds and developments involve silver, gold, platinum group metals, molybdenum, cobalt and phosphates. Exploration and development are closely regulated, but most of the NFS is open. The Forest Service endeavors to be a good host to the mineral industry, but increasingly is asked or forced to delay or disapprove mineral projects to protect the environment.

Jan 1, 1984

By G. J. Lindenburg, T. L. Wilson

The Velvet uranium mine is located in the Big Indian district of the Colorado Plateau. The uranium ore body lies within the lower Triassic Chinle Formation, and the ore is associated with west-south- westerly trending fluvial sand systems. Exploration and mining are directed by longhole drilling and radiometric sampling. Results of the gamma probing, face scanning, and geologic mapping guide mining decisions and planning. Three people are directly involved with the geologic procedures: two geologists and a mine supervisor. The two geologists map, do rib scans, and direct longhole drilling. The third man involved, the mine supervisor, has last minute directive action based on shot hole probe data.

Jan 1, 1984

By G. Rinelli, A. M. Marabini

Flotation of rutile with N-benzoyl-N-phenyl-hydroxyhmine (N-BPHA) has been investkated. Initially, floatability tests were performed in a Hallimond tube. The results indicated that rutile was floatable at pH 2-4 with N-BPHA concentration between 2 x 10-3 mol/L and 2 x 10-2 mol/L. Selectivity against hematite was recognized when operating at pH values below 2. Following the hypothesis of the formation of a surface chelate between N-BPHA and titanium ion, this compound was precipitated from a solution of Ti (SO4)2 to which N-BPHA was added. I. R. spectrometry of the rutile before and after treatment with N-BPHA solution confirmed the presence of this compound on the rutile surface. Adsorption isotherm and kinetics were determined by analyzing N-BPHA in solution with an U. V. technique. A hypothesis on the way N-BPHA is adsorbed on rutile is presented.

Jan 1, 1984

By Eupene GS

The Early Proterozioc Pine Creek Geosyncline hosts a large number of gold showings. Mineralisation types include stratiform, synsedimentary deposits within iron formation and carbonaceous mudstone; disseminations in granophyric intrusives; and quartz vein related concentrations in the form of shear fillings, saddle reefs and stockworks. Stratiform gold deposits preferentially formed near penecontemporareous faults during periods of basin instability. Intrusive basic magmas later assimilated some stratiform mineralisation and subsequently redeposited it within differentiated phases. Gold was again remobilized during regional deformation and metamorphism. Stratiform mineralisation was upgraded insitu in high strain zones and gold was mobilized into metamorphic fluids. Fluid induced fracturing during prograde metamorphism and later uplift caused the deposition of extensive gold rich vein systems. The genetic relationship between gold deposit types is reflected in the clustering of showings along regional anticlines, and provides a powerful exploration tool. The large volume of 'exhalative'òmaterial in the Geosyncline with elevated gold content suggests significant economic stratiform mineralisation may be present, and probably provides a source for later disseminated and vein deposits.

Jan 1, 1984

By Shuichiro Okada

The Tamano Smelter, which is engaged in copper smelting by Flash Smelting Furnace with Furnace Electrodes (FSFE) has since 1982 revised its computer and associated control system for the purpose of greater energy savings, stable operation, and strict environmental control. This revision is bringing about a remarkable cost savings through greater reduction in energy consumption. This paper describes in detail the following: (a) outline of renewed process computer system, (b) approach to prediction model of FSFE based on data collection and its analysis, (c) actual examples of process control by using its prediction model, (d) future trends in the computer control at Tamano Smelter.

Jan 1, 1984

By P. L. Lavery

A numerical method to derive approximate solutions for stress intensity factors for rectilinearly anisotropic bodies without resolving to complex variable approach is presented. The method is based on the assumption that the crack opening profile can be simulated by a simple curve such as an elliptic function and a relationship is found for the stress intensity factor in terms of near tip displacements. An example solution is derived for a transversely isotropic body and the results are verified with Westergaard's stress function approach. The proposed model has a great potential for the applications to fracture mechanics of anisotropic rock materials.

Jan 1, 1984

By J. E. Schiller, S. E. Khalafalla

Due to its unique surface properties, magnesium oxide (MgO) is an excellent medium to filter asbestos and other suspended solids from water. MgO operates up to twice as long as a sand filter before backwashing is required while flow rate and filtrate clarity are as good or better with MgO.

Jan 1, 1984

By Kenneth A. Pietila

The thickening and dewatering characteristics of refuse slurries are as variable as the coal mining operations and preparation plants that create them. This paper discusses these characteristics based on field studies at a number of mine sites. The connection between bench and full scale performance is confirmed with the design, construction and operation of an integrated 18m (60 ft) diameter thickener and 2.5 meter belt filter press system in Western Kentucky. The data from this system are presented.

Jan 1, 1984