Search Documents

By Askew JE

The large, massive low grade gold orebody at Mount Charlotte has demanded an innovative approach to mining engineering. In the last five years several advances occurred in the areas of rock mechanics, mass blasting, blasthole drilling and truck haulage.Successive crown pillar failures throughout the life of the mine had resulted in a continuous geotechnical program, mostly utilisingconsultants. The culmination of this workwas the development of a successful crown pillar support system. Several stopes have incorporated the technique and the most notable success has been the relatively large F3 crown pillar.In hole hammer drilling was introduced to the mine in 1979, but little work had been done to develop a blasting system to suit the 165mm diameter holes. A non-electric sequential blasting system was adapted for use at themine and up to 600,000 tonnes have been fired successfully in an individual blast. Problems with ground vibration were addressed although this work remains incomplete.

Jan 1, 1984

By Brady KT, Pattenden G

A laboratory size solvent extraction apparatus has been constructed, which incorp- orates three stages of countercurrent extraction, followed by two stages of counter- current stripping. The model uses a gravity flow system from one stage to another and air lift pumps to recirculate organic and aqueous phases. A novel pump/mixer system is used to transfer solutions from the mixer compartments to the settler compartments. The model has proven valuable in the teaching of solvent extraction principles.

Jan 1, 1984

"The Archaean komatiite-associated nickel sulphide deposits at Kambalda, Western Australia, exhibit a number of stratigraphic features that are indicative of a strong volcanic control on ore localization, including (1) a restriction to specific basal cumulate metakomatiite host units, (2) confinement within distinctive synvolcanic embayments in the footwall and (3) variations in the internal structure and composition of overlying and adjacent barren metakomatiite flow's and the distribution of interflow metasediments with proximity to the ore zones.The high magnesium content of the host units (up to 45% MgO volatile-free) in comparison with that of aphyric or spinifex- textured lavas (16-32% MgO) has been considered previously to indicate either magmas/lavas rich in intratelluric olivine or selective accumulation of olivine phenocrysts. The marked linear trend of the oreshoots, basal host units, footwall embayments and the volcanic stratigraphic relationships have been used as evidence for local linear feeding fissures. Rare relict igneous olivine in some host units is, however, demonstrably not intratelluric, and there is no direct or indirect evidence of a proximal eruptive site (e.g. footwall feeders, pyroclastic breccias, ultramafic intrusives) at Kambalda such as at some other deposits of this type. Kambalda is interpreted as a distal rather than proximal volcanic environment.Emplacement of the komatiite sequence at Kambalda was probably controlled by the locations of a few specific eruptive sites relative to regional topographic gradients and influenced by the topography of the pre-existing volcanic surface. Olivine enrichment in the basal host units occurred by in-situ fractionation and cumulus crystallization of olivine during longitudinal lava flow within linear lava conduits, possibly centralized on depressions between non-overlapping footwall basalt flows. The distinctive stratigraphic relationships are attributed to localization of lava conduits along the volcanic pitchline, flanked by more slowly moving parts of the flows. There are analogies with the physical volcanology of Modern basaltic and Proterozoic komatiitic lava flows.A corollary of this model is that the lava conduits thermally eroded and assimilated sulphidic sediments, contributing additional sulphur to sulphur-saturated komatiites or possibly inducing sulphide separation in originally sulphur-undersaturated komatiites. The latter would account for the restriction of ores to linear cumulate komatiite host units (thermally active lava conduits) and the locally mutually exclusive, but stratigraphically equivalent, relationship between the ores and sulphidic metasediments at Kambalda."

Jan 1, 1984

By Lung Cheng

The Bureau of Mines has installed passive water explosion barriers in two operating mines to determine their usefulness in U.S. coal mines. The primary objective of this field trial was to determine the effect of the explosion barriers on mining operations. Data were also obtained on the ability of the barriers to withstand the mine environment and on the effect of the barriers on belt operation, ventilation, worker travel, and rock dusting. Fifty barriers were installed at three separate beltway locations, and periodic inspections were made. A year after installation, no defects of the barriers or support hardware were detected, nor was any complaint as to the presence of the barriers made by the mine personnel. To date, 2-1/2 years after installation, the barriers have had no detrimental ef-fect on rock dusting, belt operation, or ventilation. Costs of material, fabrication, and installation are reported herein.

Jan 1, 1984

By V. Lakshmanan, Dan Mackie, J. Melnbardis

"Crystalline Flake Graphite is a strategic mineral. Since 1954 nearly all North American consumption has been imported from offshore. The Bouthillier Project in Quebec, Canada, is Orrwell Energy's bid to enter the market, with plans to begin production of a 500 TPD operation in 1984.Milling of flake graphite is considered easy, yet more problems have been encountered in flowsheet and plant design than in most other minerals. A fresh approach to existing technology was taken, giving results that are highly satisfactory. The key to graphite liberation without flake deterioration is found to be in autogeneous grinding. In addition to producing marketable coarse graphite by such autogeneous grinding, flotation and tabling, super purity fines can be produced using repeated regrinding, elutriation and flotation. This paper discusses the design of a 500 TPD plant based upon the results obtained from bench and pilot plant studies. INTROOUCTIONWhen the Black Oonald mine at Calabogie Ontario ceased production in 1954 nearly all North American crystalline flake graphite had to be imported from offshore. Orebodies in the United States were too small or too low in grade to be exploited economically.The Houthillier Township near Mont Laurier in Quebec (Figure 1) was a known graphite-bearing area The Orrwell property in that area was delineated in 1957 Some test work including minor footage of diamond drilling was carried out by Italia Copper and the MHM Syndicate prior to 1981 when Orrwell acquired the property"

Jan 1, 1984

By M. P. Board, M. J. Reus

Instrumentation was installed during construction of the Silver Shaft in northern Idaho to evaluate lining behavior and rock deformation. Rock mass displacements were monitored with multiple-position borehole extensometers. Liner stress and strain were measured with concrete pressure cells and embedment strain gages. Rock displacement data from the 5,955-ft level indicate rock mass anisotropy. Liner stress and strain data reflect high in situ stresses and nearby station and raise construction. Continued monitoring and preliminary analysis indicate that concrete-lined, circular shafts are stable for high, unequal stress fields and anisotropy in deep level mines.

Jan 1, 1984

By Robert W. Bruhn

An investigation was made of ground response to pillar retreat mining in a 1.7 meter thick seam at 108 meter depth at a site in northern West Virginia. This paper describes mining-related stress changes and movements at mine level, displacements within the overburden, ground surface subsidence and groundwater level variations. Subsidence approached 40 per cent of the mine height and continued more than a year after mining. Water levels declined in certain deep-lying strata.

Jan 1, 1984

By Douglas J. Robinson

A pilot scale process has been developed to separate mercury, tin, silver, and copper from dental amalgam scrap. Laboratory research led to a process which was operated in 55 gallon drum sized reactors to treat 2000 Tr oz charges of scrap per day. This paper discusses the development work, presents a flowsheet and gives an indication of the equipment necessary to carry out the process on a commercial scale.

Jan 1, 1984

By Uros Bajzelj

To mine very weak carboniferous schists subjected to high ground pressures the underhand cut-and-fill stoping method was proposed using an artificial plate roof. An experimental stope was mined using three consecutive levels. Rock pressures, deformation of the reinforced concrete plate, and the quality of stowing were evaluated. It was found that roof deformations were minimized if the reinforced concrete plate and uncemented backfill were replaced with cemented backfill containing reinforcement near the bottom. The mining method prevented the occurrence of high rock pressures at the face. The method is suitable for mining subvertical ore bodies with large horizontal areas.

Jan 1, 1984

By J. W. Sterner

The Bureau of Mines conducted studies on four makes of Japanese automobiles, three 1981 and one 1982 model years, received from three manufacturers to determine if their materials composition would present problems to the current technology used to process junk automobiles for metal recovery. One of each make of automobile was hand-dismantled to determine the materials composition. In addition, two nearly identical automobiles of each make were shredded at a commercial operation where all metal products and rejects were collected for analysis to determine metal and nonmetal distribution. The average weight of the four automobiles to be dismantled, less batteries, tools, and fluids, was 1,938.3 lb. The weight was distributed as 1,472.9 lb. ferrous and 115.6 lb nonferrous metals, 275.2 lb combustibles, 72.3 lb noncombustibles, and 2.3 lb electrical components. The dismantled automobiles, less gas tanks, fluids, tools, wheels, tires, and batteries, which were all removed from the automobiles that were shredded, contained an average of 1,389.1 lb ferrous and 101.6 lb nonferrous metals, 305.7 lb nonmetals, and 2.3 lb electrical components. In comparison, materials collected from the shredded automobiles averaged 1,304 lb ferrous metals, 80 lb nonferrous metals, and 341 lb landfill materials. There were no materials used in the manufacture of the late model Japanese automobiles that should present handling or processing problems to the steelmaking or secondary metal recyclers.

Jan 1, 1984

By Jouko O. Kallioinen

The control of zinc flotation at Outokumpu Oy's Pyhasalmi and Vihanti mines is described. At Pyhäsalmi the zinc flotation circuit is partially open. Zinc and other metal assays of pulp flows are measured and direct assay control of concentrates in various flotation steps is adopted. Assay control is carried out by adjusting flotation air and pulp levels. Optimization with copper sulphate ensures high Zn- recovery and minimum copper sulphate consumption. A froth depth monitor is used to measure froth quality. At Vihanti the zinc flotation takes place in closed circuit. The most important control loop is the Zn-assay control of rougher concentrate by adjusting flotation air. The quality of froth is measured indirectly and thus copper sulphate consumption is altered. The circulating load is controlled also by flotation air in the three cleaning steps. The comparison of the control strategies shows that a more sophisticated control is adopted at Pyhäsalmi because the selective flotation of this massive sulphide ore is considered to be difficult. The control strategy includes numerous tests performed by the computer and control algorithms developed for the case. The control targets of the two zinc flotations described are also different: At Pyhäsalmi Zn-assay control of final concentrate including copper sulphate optimizing, at Vihanti the control of circulating load and Zn-assay of rougher concentrate.

Jan 1, 1984

By Kenneth E. Hjelmstad

In situ leach mining operations often encounter difficulty maintaining adequate leach solution flow into the are formation. Swelling and dis-persion of clay particles in the formation are often responsible for this permeability loss. Permeability and leaching tests were done in the laboratory on clayey ores to evaluate a clay-stabilizing polymer's effectiveness in preventing these problems. Test results indicate that treating the ores with the stabilizer could maintain permeabilities two to five times greater than the long-term permeabilities present in untreated ores. Both alkaline (pH 8.5) and acidic (pH 2.0) leaches were used in the permeability-leaching tests. Since in situ leaching throughput rate is directly related to permeability, these results also indicate a potentially beneficial effect on operating parameters such as capacity and injection pressure. To determine the reasons for the success of the clay stabilizers, an investigation was conducted to cieter-mine the effect of the stabilizer on clay swelling and dispersion. Clay-swelling tests indicated that the clay stabilizer reduced clay swelling. Zeta potential measurements made on fine clay particles treated with the stabilizer were compared to measurements made on untreated particles and indicated that the stabilizer was electropositive and, therefore, could reduce the degree of negative charge on the particles and their tendency to disperse or migrate.

Jan 1, 1984

By Wen H. Su

Multiple seam mining and its associated problems are very serious in Southern West Virginia where poor planning or lack of knowledge in seam interaction often results in complete loss of coal properties. Several measures have been proposed to alleviate the interaction problems under various multiple seam conditions, but few of them are specific in terms of mining plan. Two parallel approaches are adopted for this paper. One is field investigation which consists mainly of mine site visits and gathering of data. The other is the two-dimensional finite element simulation of mine workings using the data gathered as input. Two typical cases which represent the past and present multiple seam mining practice in West Virginia were investigated. Much attention is focused on the interaction problems experienced and the important parameters controlling interaction. Several key parameters controlling interaction in multiple seam mining were analyzed. Proper mining plans, by which the interaction problems can be minimized, are proposed for the individual cases after a better understanding of the interaction mechanism was realized through finite element analyses.

Jan 1, 1984

By Leonid P. Ni, Askar M. Kunayev

It is well known that processing of the high-silicon bauxites for obtaining alumina by the hydrochemical Bayer process is irrational due to the significant losses of alumina and alkali with red mud. The main source of losses of the mentioned compounds under the conditions of leaching by the Bayer process is the formation of difficultly soluble sodium alumosilicate of the composition Na20 .Al203, 2Si02 . n H20. A conventional method of an extra recovery of alumina as well as of regeneration of alkali out of red mud is the high-temperature sintering of the latter with soda and limestone with the subsequent leaching of sodium aluminate from the sinter by water or soda solution. A sequential version of the Bayer-sintering flow chart recommended for the prosessing of bauxites with an increased content of silica is based on this method. However, the sintering method is not the only alkaline method allowing to make an extra recovery of alumina likewise of alkali from red mud. Our investigations showed/I/, that the components mentioned can be recovered by a pure hydrochemical method of treating red mud with concentrated alkaline solutions, with lime (Ca0) being present, that was earlier succesfully used in the development of the hydrochemical method of processing nepheline rocks/2/. The possibility of extracting alumina and alkali from red mud is based on the reactions which can be schematically represented in the following way:

Jan 1, 1984

By D. M. Hausen

This study identifies and describes various crystalline phases of the V205-Na20 system, and relates their properties to metallurgical aspects of vanadium production. Phase equilibria and stability ranges of sodium vanadate phases of varying molar ratios of Na20/V205 were investigated in a variety of plant products, ranging from fused "black cakes" (V20 melts) to "salt roast" calcines. Crystalline compounds, Including vanadium pentoxide, V205; sodium vanadyl vanadate, 6 phase, Na2O.V2O5.5V2O5; sodium vanadyl vanadate, y phase, 5Na20.V204.12V205; sodium metavanadate, Na20 .V 05; sodium pyrovanadate , 2Na20 .V205; and sodium orthovanadate, 4Na20.~2~5, have been characterized with the aid of X-ray diffraction patterns, infrared spectra, and optical properties in addition to chemical analyses, as a guide to mineralogical "troubleshooting" of plant problems and processes in vanadium pyro- and hydrometallurgy.

Jan 1, 1984

By Jerry W. Owens

Current steel consumption for grinding media, mill liners and rods in North America runs in excess of 400,000 tpy in the mineral processing industries. Steel consumption ranks as one of the major consumables along with energy in most operations with total annual industry expenditures in excess of $275 million. It is generally agreed that there are 3 main categories of wear responsible for this metal loss. These three main types can be loosely defined as follows; 1) Abrasion. The cutting, rubbing, scrapping and gouging of the metal surface by the ore with which it is in contact; 2) Impact. Spalling on both micro and macro scale, breakage, and deformation due to metal to metal contact; 3) Corrosion. The oxidation losses of the metal due to electrochemical interaction between the grinding media and the slurry

Jan 1, 1984

By E. C. Baker

The Bureau of Mines estimated the economic feasibility of investing in a directional hole methane drainage project in the Pittsburgh coalbed for 5 yr in advance of mining. This report estimates the capital investment and operating cost of recovering 325 MMft3 of methane gas per year and the selling price of approximately 317 MMft3 of gas per year. The labor, equipment, and supply requirements were determined from those of a previous directional hole drilled at the Emerald Mine, near Waynesburg, PA. The cost of equipment, materials, services, and labor are in third quarter 1982 dollars. They were obtained from vendors, contractors, and the U.S. Department of Labor. Findings indicate a total capital investment of $1,381,160. Annual operating cost amounted to $167,690. At a wellhead price of $2.05 per thousand cubic feet, the sale of approximately 317 MMft3 of gas per year results in a rate of return on investment of approximately 25 pet.

Jan 1, 1984

By David Firewick, Daniel Stewart, Richard Rein

Panel caving of the Henderson orebody began in August, 1976. Fifty months later, on September 10, 1980, the cave zone appeared on surface as a steep-walled cavity positioned directly above the initial cave area. Although surface survey data revealed the development of a slight depression over the production area, surface inspection by geologists, three days prior to breach- ing, resulted in no evidence of impending glory-hole development. Geologic factors such as rock contacts and alteration-zone boundaries had little influence on the location of the initial glory hole. Since initial breakthrough, the glory-hole shape and growth have not directionally followed caveline advance because of topography and faulting. Based on periodic data, mine production has resulted in immediate growth of the Henderson glory hole.

Jan 1, 1984

By F. T. Lee

Directional dependence of strength and deformation properties of the Mount Waldo granite pluton in southeastern Maine is controlled by joints and microfractures whose orientations are linked to flow- induced alignment of microcline crystals. Longitudinal and cross joints which formed during cooling of the mass, as well as much younger sheeting fractures, are commonly associated with subparallel, discontinuous microfractures. The orthogonality of microfractures (open, closed; filled, unfilled; bubble planes) establishes the ease of splitting of the granite. The easiest splitting direction (rift) is subhorizontal, the second easiest direction (grain) is parallel to the cross joints, while the direction of least easy splitting (hardway) is parallel to the longitudinal joints. Static and dynamic measurements made in the field and laboratory established that structural features are responsible for the marked stiffness anisotropy of the granite. In the central part of the pluton the static Young's modulus in the north-south direction averages 31.1 GPa, and 20.9 GPa in the east-west direction; the stiffer direction being parallel to the long C-axes of microcline phenocrysts and microfractures as identified in outcrop, core samples, and thin sections. Vertical downhole sonic measurements of dynamic moduli ranging from 2.5 to 16.2 GPa appeared to be anomalously low when compared to the static horizontal values. However, the field sonic values were confirmed by laboratory sonic pulse testing of oriented cores. The field results reflected closely spaced layers of open horizontal microfractures. Those deformation and strength properties that are closely tied to bubble planes, filled microfractures, and microcline orientation could be extrapolated to greater depths with good hope of success.

Jan 1, 1984

The Teutonic Bore deposit lies in a major greenstone belt within the Archaean Yilgarn craton of Western Australia. It occurs towards the base of a suite of tholeiitic basalts, some 100 m above a felsic volcanic pile of rhyolitic composition. Sediments comprise a minor, albeit important, percentage of the mine stratigraphy.The deposit consists of a single, steeply dipping lens of massive sulphides totalling 1.4 million tonnes grading 4.16 per cent Cu, 16.4 per cent Zn, 1.22 per cent Pb and 203 g/t Ag. In addition, cross cutting "stringer" mineralisation in the footwall contributes a further 0.75 million tonnes at 2.38 per cent Cu, 1.92 per cent Zn and 52 g/t Ag to the mining reserves. Principal primary sulphides in massive and disseminated mineralisation are sphalerite, pyrite, chalcopyrite and galena, while minor amounts of arsenopyrite and argentiferous tetrahedrite are also present. Weathering has affected the primary mineralogy down to at least 90 m, resulting in a strongly leached oxide profile to about 85 m, overlying a thin, erratic zone of chalcocite supergene enrichment.Lateral metal zoning is marked both in massive sulphide and stringer mineralisation, with Cu/Zn ratios decreasing away from the centre of the orebody. Alteration is well developed in association with footwall stringer mineralisation, changing from a central Fe-Mg carbonate, chlorite and silica alteration zone below the massive sulphides to an outer halo of sericitisation. The spatial distribution of these minerals is patchy. Geochemically, the footwall alteration zone is characterised by central Cao, Na20 and Sr depletion (with less regular enrichment of SiO2 , Fe and MgO), surrounded by a peripheral zone of K20 enrichment.Evidence supports a classic volcanic-exhalative origin, involving submarine discharge on the flanks of a rhyolitic dome and accumulation of the massive sulphides in a local palaeotopographic depression. The sulphides overlie their feeder zone as shown by alteration and stringer mineralisation. Tholeiitic wallrocks are thought to be genetically unrelated to the mineralising solutions, although their presence as a cap over the felsic volcanics may have permitted the build up of a circulating metalliferous brine system prior to sulphide deposition.

Jan 1, 1984