Search Documents

Prevent the propagation of a fire and control the spread of smoke and toxic gas in underground mines. Approach A fire door suitable for large openings in underground noncoal mines and providing protection for openings requiring 11/2 hours of fire resistance, a 250°F maximum temperature rise, and high pressure differentials was de-signed, laboratory tested, and in-mine tested. How It Works The door is a double-acting swing type. Its two panels. connected by an overhead linkage, open in opposite directions. Consequently, high pressure differentials across the door have little effect on the force required to open and close the door. The door is constructed of 14-gauge sheet steel skins welded to both sides of a 5-inch-wide steel channel frame. The frame is rein-forced with 5-inch-wide steel channels in a horizontal and diagonal pattern. The voids between the reinforcing members are filled with a ceramic fiber insulation material to limit the surface temperature rise of the unexposed side of the door during a fire. A fire -resistant neoprene-coated fabric is used to seal around the edges of the door panels. The door is opened and closed by an air cylinder, attached to the over-head linkage and operated by lanyards on either side of the door. The door design includes an optional airlock manway for drifts of adequate width.

Jan 1, 1983

By A. E. Hunt

Over the past twenty-live years since large scale truck haulage in open-pit mining began, the periodic introduction of Larger capacity vehicles has provided increased productivity and reduced costs. WISEDA Ltd. has introduced a 220 ton capacity, two-axle rear dump, diesel-electric truck for the world-wide large open-pit mining industry. Design features and components selected in the development of this vehicle will be presented along with operating experience and a brief history of rear dump truck evolution.

Jan 1, 1983

By J. E. Schiller

The Bureau of Mines is investigating methods to treat waste water that contains cyanide. This report describes a new method that removes heavy metals and all forms of cyanide. In the first step, hydrogen peroxide and sodium thiosulfate are added at pH 7 to 9 in a 1:2 molar ratio to convert free and weakly complexed cyanide to nontoxic thiocyanate. Then steryldimethylbenzylammonium chloride is added to precipitate ferro-cyanide, and finally, ferric sulfate is added as a sweep floc and sequestrant for heavy metals. After the suspended solids settle, the water is polished by filtering. The water initially contained 1 to 5 mg/L Fe, 1 to 5 mg/L Cu, and 10 to 30 mg/L total cyanide; the level of each of these constituents was reduced to less than 0.02 mg/L.

Jan 1, 1983

By Jonathan G. Price

Silver-copper-lead deposlts in Precambrian, Permian, and Cretaceous red-bed sequences near Van Horn, Texas, have the following features In common: (1) mineralization controlled by steeply dipping fractures in sandstones, (2) lack of ore In overlying and interbedded limestones, (3) absence of igneous intrusions, (4) sulfide ores without typical hydrothermal gangue minerals, and (5) associated arsenic, molybdenum, zinc, and cadmium but not gold. Ore was probably deposited along fractures by reaction between low-temperature, oxidizing, metal-rich ground waters and sulfide-bearing waters or rocks. Detailed mapping and studies of fracture patterns indicate that mineralization occurred during Basin and Range extensional deformation, thereby postdating major Trans-Pecos igneous activity.

Jan 1, 1983

By John H. Clark

This paper outlines new technological improvements in underground trackless equipment for the metal mining industry with emphasis on maintenance related developments for Load Haul Dump machines. Also new developments on other types of equipment are covered including drills, road headers and electric LHD's.

Jan 1, 1983

It is possible from simple gas behavioral theories to develop more complex relationships which allow prediction of transport phenomena such as diffusivity and viscosity of gas mixtures. Such physical data can be used in engineering calculations for both bulk gas movement and gaseous chemical species movement. Both of these are important in the solution of mines ventilation systems. There are specific limits of flammibili!'y of some common mines gases.

Jan 1, 1983

By J. Frederick Stampfer

Current certification testing of self-contained breathing apparatus includes tests with human subjects wearing the apparatus while exercising. During these tests, certain apparatus variables are measured during rest periods. Because of concerns that the present tests may not accurately simulate the stresses to which an apparatus is subjected in the field, the Bureau of Mines proposed new human subject tests. It was also felt that different measurement techniques would supply more reliable data on the apparatus response to these stresses. The Los Alamos National Laboratory was asked by the Bureau to evaluate the proposed tests and monitoring techniques. The major conclusions derived during this study are these: (1) The proposed tests are not too physically demanding. (2) As long as human test subjects are used, a minimum subject weight should be required for certification tests. (3) Important apparatus variables are the breathing resistance, temperature, and carbon dioxide and oxygen concentrations of the inhaled gas. (4) Continuous monitoring should be used, rather than monitoring only during rest periods. (5) New pass/fail criteria based on realistic estimates of the user's physiological requirements, as tempered by present and future engineering limitations, are needed. (6) When available, breathing machines, rather than human subjects, should be used for most certification testing. (7) A more realistic ergonomics test than that proposed is needed. (8) A gas leak test for the system and a facepiece leakage test are also needed.

Jan 1, 1983

By Gene Asai

The Bureau of Mines investigated the caustic extraction of alumina and soda from retorted dawsonite-bearing oil shale, as part of a program to devise technology for treating alternative domestic sources of alumina for the production of aluminum metal. Colorado oil shale yielding 13 pct oil (35 gal/ton) and containing 12 wt-pct dawsonite (representing about 4 pct extractable alumina) was retorted to obtain oil-free (spent) shale Spent shale was leached with dilute NaOH to determine the effect of particle size, retorting temperature, leaching variables, and storage conditions on extraction of alumina and soda and dissolution of impurities. Maximum alumina and soda extractions were obtained by promptly leaching minus 28-mesh spent shale, obtained by retorting raw shale at about 5000 C, with 0.5N NaOH. Under these conditions, dissolution of impurities such as Ca, Fe, Ti, and P was low. Leaching tests were made on spent shale stored for periods of up to 30 days at 0° to 42° C and at 0 to 100 pct relative humidity (RH). These tests indicated that significant reductions in alumina extraction would occur if spent shale were stored in ambient Colorado air under naturally fluctuating temperature and humidity.

Jan 1, 1983

By B. J. Fryer, R. P. Taylor

"As a monitor of the processes involved in the formation of granitoid mineral deposits the coherent group behaviour of the rare earth elements (REE) actively reflects changing fluid characteristics. For example, in the porphyry environment, magmatic-hydrothermal fluids produce potassic alteration with strong enrichment in the light rare earth element s (LREE), reflecting their high pH, low fluid/rock ratios, and the dominant role of CI- complexing in metal (i.e. Cu, Au) transport. With increasing fluid/rock ratios and decreasing pH accompanying the progressive involvement of meteoric fluids (and the production of propylitic, argillic, and phyllic alteration) anionic species such as F - and CO, 2- become important in metal (e.g. Mo, W,) transport through complexing, and their activity in the hydro thermal fluids is illustrated by mobilization of the heavy rare earth elements (HREE).The relative involvement of CI- versus F - versus CO32- in metal transport in other granite-related systems can also be monitored through REE behaviour. Hence granitoid tin-tungsten mineralization and associated greisenization typically exhibit heavy rare earth enrichment and evidence the importance of F' and CO32- in metal transport. Similarly, heavy rare earth element enrichment in hydrothermal uranium deposits can be related to the transport of uranium as carbonate complexes. REE are widely accepted as powerful tools in the study of rock petrogenesis, but their use has been neglected in the investigation of mineral deposits. The recognition of the systematic variation of REE distributions in granitoid mineral deposits suggests that the application of REE geo chemistry, particularly when integrated with fluid inclusion and isotope studies, can provide (1) an effective method for identifying the physicochemical controls of metal transport and (2) a useful criterion for elucidating metal distribution."

Jan 1, 1983

By A. D. Hunter, J. M. JR. Moore

"The Aldermac deposit and associated prospects occur in the Noranda Archean volcanic centre of the Abitibi greenstone belt. Over two million tons of are grading 1.65% copper, with minor gold and silver, were mined between 1933 and 1943. The deposit has features in common with the Vauze and Millenbach mines in the same district.Recent detailed mapping, geochemistry and petrography combined with data from former diamond drilling and mining operations permit a re-interpretation of the Aldermac area. The orebodies and spatially related sulphidic zones are con eluded to be volcanogenic.The host rocks are a chemically bimodal suite of mafic and rhyolitic flows, volcaniclastics and related subvolcanic intrusions. Massive sulphide lenses are spatially related to a quartz-feldspar- phyric rhyolite dome and siliceous, volcanic-exhalative sedimentary rocks, The succession is cut by gabbro and syenite, related to later stages of volcanism, and by post Kenoran diabase dykes. Regional metamorphism attained the low greenschist facies, but the rocks lack penetrative deformation.Hydrothermal alteration is primarily an intense silicification of mafic volcanic rock s enveloping, or lying below, sulphidic zones. Chlorite and sericite alteration zones, including dalmatianite, are more locally developed and have a closer spatial relation to mineralization, as do epidote, calcite and calcic garnet.The structure is complex and cannot be explained by isoclinals folding; rather it reflects concurrent faulting, and extrusive and intrusive activity. Fault blocks were rotated and exhibit opposed facing; the original selling was possibly a submarine graben.Sulphidic zones occur within mafic and felsic volcanic rocks and at the interface between the two; there is thus potential for discovery throughout the known stratigraphic succession. Exploration conducted according to a volcanogenic model is advisable, particularly in the light of recent discoveries in similar rocks of the Amulet area."

Jan 1, 1983

By P. R. Sheorey

I read this interesting paper on pillar strength in some detail because this is also my area of interest. It has long been the desire of mining rock mechanicians to predict pillar strength from laboratory compression tests. Considerable literature is available on compression strength of rocks and coal but many of these experiments were conducted not for pillar design but for rock behavior. I have a few comments on the author's approach to pillar design, especially equation (33). Two important factors, which the author seems to have excluded, can be added to the right side of equation (2): time-dependence of strength and the influence of mine environment on strength (moisture and weathering.) The author has taken considerable pains to analyze a large amount of testing data in [Table 1], yielding the various exponents ci of equation (2) (or the subsequent equations derived from it.) He has, however, not shown by means of a worked out example how these values of [Table 1] could be applied to a practical pillar design situation. It would have been interesting to compare predicted pillar size using equation (33) with an actual case. Alternatively, equation (33) could have been used to explain the failure of a pillar, if such a case history were available. Consider we have a large number of case histories of stable and collapsed pillars in a seam and we conduct a large number of tests in a laboratory press. The exponents [ci] can then be determined for actual pillars as well as for test specimens. Thus, equation (2) will read [ ] Since laboratory testing conditions (e.g., between steel platens) are different from the conditions on pillars, the exponents [ci] in

Jan 1, 1983

By J. B. Parry

Three types of high-strength cold-rolled steels are discussed. Two are currently being developed at Iscor: rephos phorized steel and niobium microalloyed steel. Heat treatment after cold rolling is carried out in batch annealing furnaces. A third type, dual-phase steel, which requires a continuous annealing treatment for economic production, is also described. The properties, strengthening mechanisms, and applications of these three steels are examined.

Jan 1, 1983

By P. Hickey

"The object of this paper is to describe how the Iron Ore Company of Canada develops its management personnel. It will elaborate on the practical application of Supervisory Training and Management Development.Why are Supervisory Training and Management Development important? The answer has been the subject of many textbooks. Dr. Ken Blanchard, author and consultant, addressed this issue concisely when he said that effective managers and organizations must do two things, ""get results and develop people"". lPeople development at IOC is best illustrated through its supervisory training and management development programs. For the past twenty-five years IOC has been recognized as an industry leader in the training field. Periodic studies have played their role in establishing and maintaining this distinction. For example, in 1974, the company decided to review and up-date all its training programs. At this time, it established its own Task Force on Training and this resulted in the development of many of our present programs. Today, Supervisory Training (i.e. for first and second level management) at the Carol Project in the Labrador City area consists of various programs including: New Foreman Induction, Foreman Entrance School, Basic Management Skills, Management II, and Effective Presentations."

Jan 1, 1983

By Ralph B. Hall

Examination of cored material from the Southern Extension of the Florida Phosphate District has indicated a decidedly complex and diverse sequence of phosphatic sedimentary units. The perfunctory logging techniques formerly used in the Central District are inadequate to properly describe the intricate geology of these sediments. Adequate geologic training and familiarity with the potential ramifications of his judgement are a necessity for the logging geologist. A combination descriptive-graphic logging model is proposed that utilizes a standardized sediment nomenclature system and descriptive symbols for type materials commonly found in these sediments. Justification for adoption of this or a similar logging model is discussed.

Jan 1, 1983

By V. R. Miller

The Bureau of Mines conducted research on substitute brazing filler alloys with properties similar to those of silver filler alloys in an effort to conserve silver and reduce hazards from cadmium emissions. Experimental work was conducted first on the commercial silver brazing alloys BAg-I, BAg-la, BAg-2, and BAg-3 to establish criteria for evalu-ating the substitute alloys. Properties investigated included the wettability of copper, brass, and steel substrates, and the strength of joints made with the filler alloys. A series of experimental alloys containing 50 to 60 pct Cu, 20 to 28 pct Mn, and 17 to 30 pct Zn was prepared and evaluated, together with Cu-Mn-Zn alloys with 5 pct Pb or 2 pct Ni. Wetting properties and joint strengths were not as good as those for silver filler alloys, and the high application temperatures reduced the copper and brass base metal strengths. However, experimental alloys containing 70 pct Cu, 15 to 20 pct Mn, and 10 to 16 pct Sn had wetting and strength properties approaching those of the silver filler alloys. The application temperatures for these alloys were high-er than those for silver fillers, but not as high as those for the Cu-Mn-Zn alloys. With the Cu-Mn-Sn alloy fillers, copper alloy joint members are less deteriorated by recrystallization than when applying Cu-Mn-Zn alloys. The Cu-Mn-Sn system has potential for further devel-opment as a substitute brazing alloy system, particularly if the melting temperature can be reduced by the addition of other elements without decreasing the ductility and wetting.

Jan 1, 1983

By Jane Applegate

This report documents efforts to design, develop and test a training approach which would assist front-end loader operators in the acquisition of skills and awareness to reduce the probability of their involvement in accidents in the mining environment. The goal of this project was to prepare and use (on a trial basis) a training method and materials which would be generally applicable to any loader and surface mining operation while at the same time, be adjustable by mine personnel to meet the specific needs of each mining operation. This effort resulted in the Front-End Loader Training System, a structured, performance-based training approach with diverse instructional aids and classroom and on-machine training experiences. Validation of the System at a large western mine demonstrated the utility and flexibility of the training approach and materials.

Jan 1, 1983

By H. O. Seigel

This is an introductory paper on a new method of prospecting for mineral deposits which has been developed by Scintrex Limited. The method, which we call Luminex, for luminescent mineral exploration, is based on time- resolved mineral luminescence created by an ultraviolet light source. It has the ability to detect and resolve a group of key minerals which are either ore minerals themselves, or more often, are accessory or pathfinder minerals for certain types of economic ore deposits. Fortunately, these minerals are commonly found at the earth's surface, even in areas of considerable weathering. The method extends the range of mineral deposits which are remotely detectable from the air to include those such as tungsten, tin, molybdenum, gold and bedded lead-zinc deposits and, is therefore, a natural supplement to our three classical methods of airborne geophysics.

Jan 1, 1983

By Lucia Kuizon

The Cactus Springs Roadless Area Review and Evaluation (RARE II) study area (No. A5188) comprises 12,800 net acres (5,180 ha) in San Bernardino National Forest in west central Riverside County, California, about 20 air miles (32 km) southeast of Palm Springs. Mineral investigations are made by the U.S. Bureau of Mines on National Forest lands identified as Further Planning Areas in the RARE II program. The Bureau of Mines reviewed literature, mining claim records, and production files; examined the study area; and mapped and sampled mineral properties where appropriate.

Jan 1, 1983

By J. J. Scott

INTRODUCTION Rock mechanics theory needs to be applied to solve ground control problems, but in the final analysis the mining method and equipment which is used will be those which solve problems in a practical manner. Equipment and its inherent productivity and safety as supplied as "off the shelf" items by manufacturers often dictate the size of mine openings. Operators may tolerate falls of ground and associated hazards if productivity and safety problems are not too severe. In this whole process the costs of mining finally dictates just what system will be employed and what equipment will be used. True solutions to ground control problems sometimes require that the mine operator step back and totally rethink his problems. The true cost of accidents are often missed and hidden in overhead costs. Losses in production and accompanying profit are not fully considered, false economics, such as using inappropriate roof support devices, are undertaken at times when using the most expensive devices to totally eliminate accidents may be the best overall solution. Automation to remove the worker from the hazard area is often over- looked as the initial capitol expense to apply it may be high. Cooperation between mine engineers, mine operators, safety personnel, equipment suppliers, and government inspectors, both state and federal, is required to reach workable solutions that best meet the goals of all parties.

Jan 1, 1983

By Timothy A. Clancy

To help reduce the Nation's dependence on imported chromite, the Bureau of Mines is conducting research on the use of dolomites as an alternate material. Dolomite is a plentiful domestic resource and offers certain advantages as a refractory raw material. A review of the literature has indicated that there are many sources of high-purity dolomite in this country and that European nations use a greater proportion of dolomite refractories, primarily in steelmaking, than the United States, The Bureau of Mines characterized 14 domestic dolomites as to chemistry, density, mineralogy, microstructure, and thermal behavior, to develop baseline data on their suitability as refractory raw materials.

Jan 1, 1983