Search Documents

By B. G. Bunting, D. L. Abata, J. Robb, J. H. Johnson

Toxic gases produced by the detonation of six explosives were measured in an underground hardrock metal mine during mining operations. The explosives included two semi-gelatin dynamites, three slurry explosives, and an ammonium nitrate, fuel-oil/ammonia dynamite combination. Explosives were detonated at the face of a drift and toxic gases produced by the detonation were trapped at the end of the drift by a bulkhead located a short distance away from the face. Toxic gas concentrations were then measured with direct readout instruments and together with the containment volume, the toxic gas volumes per mass of explosive were calculated. Toxic gas measurements were found in the following ranges (ft3/1bm): NO, 0.0100-0.035; N02, 0.003-0.019; CO, 0.08-0.30; SO2, 0.00-0.05; and CO2, 0.7-1.8. Results showed that toxic gas production (ft3/lbm) correlated with the densities (kg/m3) and energy densities (kJ/kg) of the explosives tested.

Jan 1, 1983

By J. A. Wates

The paper examines the consequences of dam building with slime of high water content, and therefore Iow relative density, such as the tailings usually associated with the extraction of uranium. It shows how a Iow relative density reduces the practical maximum rate of rise, and hence the establishment cost, of slimes dams built by conventional means. Further hidden costs of such tailings dams are examined. It is concluded that dewatering of tailings before their disposal is the most cost-effective means of increasing the rate at which a particular dam can be constructed, or of reducing operating or stability problems on existing dams. In the longer term, underground disposal seems to be a feasible alternative. However, it is pointed out that there are other factors that can compound the operating difficulties, and that these should be investigated before remedial steps are taken.

Jan 1, 1983

By Russell A. Schreiner

In conjunction with the Geological Survey, the Bureau of Mines conducted a mineral investigation in 1981 and 1982 of the Santa Rosa Mountains Wilderness Study Area (WSA), Riverside County, California. The Bureau of Mines is responsible for the mineral survey of mines, prospects, and mineralized areas in and near the WSA. A literature search was completed to obtain information concerning mineral occurrences and mining activity that relate to the WSA. A field investigation inside, and up to 1 mi outside, the boundary of the WSA, disclosed one prospect. This prospect was surveyed by compass and tape, and five samples were taken to determine the representative mineral content. No attempt was made to expose concealed mineralization or to re-open caved workings. All five samples were analyzed by fire assay for gold and silver and by colorimetric methods for tungsten. Two of the samples were analyzed by semi quantitative spectrographic methods to determine if any unsuspected elements were present. All analyses are furnished in this report except for the semi-quantitative spectrograhic analyses. Complete sample analyses are available for public inspection at the Bureau of Mines, Intermountain Field Operations Center, Building 20, Denver Federal Center, Denver, CO 80225.

Jan 1, 1983

By Kidd A

The operations of Minerals Mining and Metallurgy Limited's (MM) South mine including both the mining and metallurgical aspects are described. After treating the history of the company, the geology of and the mining of the open pit are given including sections on pit design, mine planning and grade control. Details of the metallurgical process develognent lead into the current treatment practice and then sane thoughts on future programmes are presented.

Jan 1, 1983

By Thomas E. Shufflebarger

Definition of glass sand prospects may be modified by constraints which range from demography to critically important product-control. Characteristics of usable raw materials, physical and chemical, are discussed; an ideal raw material is defined. Following field investigations and preliminary sampling, evaluation of selected prospects includes use of modern drilling techniques, viz.: core, percussion (air-hammer), auger, jet, rotary jet, split-spoon and other. Nearly complete core (sample) return is mandatory. Land-use regulations, availability of water and transportation continue to direct exploration in a major sense. But fitting a prospect to burdensome politics nay be considered a decidedly negative factor.

Jan 1, 1983

By Caner Zanbak, Erdogan Yüzer, Mahir Vardar, Kemal A. Erguvanli

The Hasancelebi iron deposit in Eastern Turkey is a very low grade (average 20% oxide) magnetite body consisting of 720 million longtons of proven reserve at a 10% cut-off limit. The ore-bearing scapolitic oclcs cover an area of approximately 4300m x 300m, and the thickness of the outcropping deposit exceeds 300m. Prefeasibility project studies revealed that a one degree decrease in a 45° final slope angle of the proposed pit would require excavation of approximately 10 million cubic meters of excess waste material, for a projected pit bottom 300 meters below the valley floor. There- fore, determination of the final slope angles of the open pit was considered to be the most important task in the feasibility analysis of this project. In this investigation, the main emphasis was given to collection, compilation and evaluation of the engineering geological, hydrogeological and rock mechanics data of the highly fractured and weathered rocks. Due to the presence of intense fracturing, the rock wedge analysis method was used for projected 30m-high benches and the circular failure analysis method was used for the stability of the projected final pit slopes. The proposed bench slope angles ranged between 60° and 80°, whereas the projected final slope angles varied between 30° and 48°, depending on the slope heights and groundwater levels.

Jan 1, 1983

By Thomas Lien

Session 1 - 1 :45 p.m. June 27,1983 Session Chairman: Robert Diederich, RMCMl New Mexico Vice President MR. DIEDERICH: My name is Bob Diederich. I'm the Vice President of the Rocky Mountain Coal Mining Insitute from the state of New Mexico. I'm manager for the Navajo Mine down in Farmington, New Mexico and also project manager for a new mine that we're starling out called the LaPlata Mine in the same area. I'd like to introduce our first speaker, Tom Lien, who is the Director of Engineering, Western Division of AMAX Coal Company. He is responsible for mine engineering, environmental engineering, permitting, reclamation, planning, design and construction plant engineering, geology exploration, quality control and real estate for the western division. He joined AMAX Coal in 1980 as manager of preparation and quality control and was promoted to the present position in August of 1980. He has a BS in geological engineering from the University of Mines. He previously worked for Kennecott Copper Corporation in Hayden, Arizona from 1965 to 1970. He worked as a mine geologist, mill metallurgist, mine production and quality control engineer. Then he also worked for Kaiser Steel Corporation, Eagle Mountain Iron Ore Mine in California, 1970 to 1977. Worked as a process engineer and plant superintendent at that place. Then he was employed by Mountain States Research and Development, Tucson, Arizona, 1977 to 1980. Worked as a senior process engineer and operation superintendent. So without further ado, I'd like to introduce Tom Lien who will talk to us about in-pit coal crushing. MR. LIEN: Thank you. The official title of my paper is actually: "The Potential for In-pit Crushing and Conveying in the Powder River Basin." The Powder River Basin is one of the world's greatest coal fields and will be an important source of energy for centuries to come. About one-eighth of the total coal producing in the United States comes from the Powder River Basin, and 80% of that production came out of Campbell County, Wyoming last year. The growth potential for this region is projected to be enormous. New technology as well as existing technology will make this region competitive in the decades ahead. Understanding the current status of the Powder River Basin, both the mines and the possible methods for changing the means of material movements within the mines is the subject of this paper. Each mine is unique and must be addressed specifically with respect to the application of new and innovative technology. There have been many articles written in the recent mining journals on in-pit crushing and conveying applications, including costs which are very interesting, enlightening and I recommend it to any company considering such installations. To give a general setting, coal production in the United States for 1982 was about 800,000.000 tons. This production came principally from six regions, the Applachian fields of the eastern states where bituminous and anthracite coals have been mined for almost three centuries, the Midwest located in the upper Mississippi Valley are often typified by huge dragline operations of which AMAX Coal has three right now, the Gulf Coast lignites. feeding mine-mouth power plants, the vast bituminous and sub-bituminous departments of the four-comer states of Arizona, New Mexico, Colorado, and Utah and finally the Northern Great Plains lignite fields currently being developed and the sub-bituminous fields of Wyoming and Montana including the Powder River Basin. The Powder River Basin is located in northeastern Wyoming and southeastern Montana. It is the darker brown right in the center of the photograph. It covers about 18,000 square miles. It's about 200 miles north to south and 90 miles east to west. The shallowest coal beds are on the east, north and northwest edges of the basin with deeper coal beds toward the center in the same kind of relationship. There are about one trillion tons of coal in the Powder River Basin, that's the one with 12 zeros after it. A little bit there. It's distributed in many, many seams at varying depths to the current topography. In 1982 about 100,000,000 tons of coal were mined from this basin and 81,000,000 tons came out of Campbell County, Wyoming. The mines that are shown in this picture are basically the mines around the basin edge. The principal area that I'll be talking about is the eastern edge down where it shows Gillette and Campbell County. Geologically the Powder River Basin is the Fort Union formation. The most productive seam is called the Wyodak or Smith-Roland or the Anderson-Canyon, depending upon where you're located. There is about 75 billion tons of coal in the Wyodak of which about 23 billion are considered surface minable today. the coal is Paleocene in age, about 40,000,000 years old. It was once an old Delta region very much like the Mississippi River delta is today. During the 100,000 years that this deposit was formed peat accumulated to a thickness of about 365 feet. It was later buried and turned into sub-bituminous coal. All of the coal mined in the basin is for the electric utility industry. This coal has a typical BTU content of about 8,300 plus or minus about 4,500 BTUs. Sulfur coal is generally less than'/ %, thereby making this coal compliance coal in terms of sulfur dioxide emissions, 1.2 pounds of sulfur dioxide per million

Jan 1, 1983

By Hempenstall J, English W

Mine management has a responsibility under the various acts of state parliaments for the adequate ventilation of existing workings. It also has a need to plan adequately for the ventilation of proposed workings. Future workings alternatives have become progressively more complex and ventilation planning of the various possibilities must be undertaken within an atmosphere of rapidly changing market circumstances, etc. Any non-optimal solution will prove more expensive than necessary on both capital and cost bases. Clearly these increasing and alternative ventilation demands of coal mines in Australia have multiplied the work load of ventilation engineers. Management in general has for some time been aware of the advantages of using computers for commercial applications such as payroll and stores inventory. However, while the hand held calculator has replaced the traditional log tables and slide rules for smaller engineering calculations, the larger digital computer has not made the same

Jan 1, 1983

The overall mineral assemblage of the Broken Hill orebody is similar to that of a skarn. However unlike the classical skarns it does not represent contact metamorphism of pre-existing limestone beds. It is a stratiform accumulation of exhalative-sedimentary silica, sulphides, (Ca, Fe, Mn) silicates and carbonates, fluoride and phosphate that has later undergone regional metamorphism. The resulting development of coarse-grained quartz, sphalerite, galena, rhodonite, bustamite, mixed carbonates, fluorite, apatite and many minor phases has produced a sulphide-rich skarn- like mass that like many others of its kind, might best be referred to as a stratiform skarn. Recent investigations of occurrences of this type are showing that the incidence of concentrations of particular metamorphic minerals in and adjacent to such orebodies are closely related to bedding and to former sedimentary facies patterns. From this it appears that the mineral assemblages may be used to deduce not only the nature of the materials laid down in the beds, but also the physico-chemical conditions under which sedimentation took place. Several stratiform deposits, including Broken Hill, are used as examples to show that variations in these conditions may have a profound influence on the subsequent response of the rock to regional metamorphism and hence on the mineral assemblages that finally develop.

Jan 1, 1983

By G. R. O?Neil

The justification for a "ligand- selective' approach to fine mineral beneficiation via flocculation is established initially. Special emphasis is placed upon the need to identify non-selective, interfering and complicating adsorption effects. Specific strategies directed towards the design and synthesis of complementary selective flocculants are detailed using a number of different polymers and chelating agents as examples. In this regard, the affinity of polymer-bound ligands for metallic cations, ligand concentration, possible modes of attachment, the application of spaced-out ligands and other considerations in the preparation of selective flocculants are highlighted.

Jan 1, 1983

By A. K. Sinha

The annual production and productivity of underground coal mines in recent years declined from 334 Mt (368 million st) and 14.5 t (16 st) per man per shift in 1969 to approximately 254 Mt (280 million st) and less than 8 t (9 st) per man per shift in 1977. Productivity is still hovering at about 7.25 t (8 st) per man per shift. According to US Bureau of Mines, the estimated US coal reserve is about 396 Gt (437 billion st), 68.65% of which is obtainable by underground mining methods. Approximately 153 Gt (169 billion st), or about 85.2% of the high Btu premium coking coal of the eastern US, would need to be extracted by underground mining methods. It is thus apparent that under- ground mining will continue to play a major role in total US coal production, which is expected to rapidly increase to about 1.1 Gt (1.2 billion st) by 1985, with about 606 Mt (668 million st) being contributed by underground mines. Production Potential of Continuous Mining The production potential of a continuous mining section depends primarily on the producing ability of the miner, transporting ability of the face haulage, and the matching of the two systems. The producing ability of the continuous miner depends on its actual cutting ability and the time available for cutting coal. The performance of 10 continuous miners operating in coal seams of various thicknesses were monitored in Pennsylvania and West Virginia, using continuous electrical power analyzers and time studies. The recordings on current and power strip charts yielded an accurate analysis of the cutting, trimming, and idle times of the machines on a full shift basis. Continuous miners of various models and sizes from 112-298 kW (150-400 hp) were monitored. Based on actual cutting time, the average cutting ability of the machines, as shown in [Fig. 1], ranged from

Jan 1, 1983

By John L. Watson

The processes of magnetic separation and cyclone classification are common in the mineral processing industry, and frequently the two are found in consecutive stages in the beneficiation of a magnetic mineral ore. The application of a magnetic field across the cyclone, to combine the two stages in treating a magnetic mineral pulp, has been investigated with a view to possible practical applications in the mineral industry The results of this research reveal that magnetic particles can be manipulated within the cyclone body by the application of a magnetic field, and that magnetic grades may be significantly upgraded with recoveries in excess of 90%.

Jan 1, 1983

By Morrison R. D

This paper describes major events in the design, construction, camtissioning and operation of the Elura concentrator. It covers the period fran September, 1974 when laboratory testwork on drill core cotmenced to March, 1983 when the concentrator catmenced operation on run of mine ore following successful completion of initial ccnmissioning tests. The concentrator was designed to treat 1.1 million tonnes of lead-zinc-silver ore per year with a plant availability of 89 per cent. This treatment rate has been achieved for test periods.

Jan 1, 1983

By Ronald A. Crowson

Detailed stratigraphic studies of the overburden at North Carolina Phosphate Corporation new South Creek Mine have delineated several aquifers and acquicludes within the 30-meter-thick overburden section of late Pleistocene sands and clayey sands. A major aquifer occurs in the 10-meter-thick sequence of shelly sands of the early Pleistocene Croatan Formation. The water-charged Croatan sands thicken into a paleodrainage surface on top of the Pliocene Yorktown Formation, a major aquiclude. A three-phase dewatering program is projected: 1) improve surface drainage around mine perimeter to reduce both flowage into the pit and rainfall recharge; 2) use a wellpoint system to dewater the upper 8 meters; and 3) use recharge wells along the axis of the paleo- drainage to dewater the overburden below 8 meters.

Jan 1, 1983

By Dan A. Permenter

This paper assesses some of the critical factors that must be considered and addressed in the implementation of small computer systems for technical applications within a coal company. Aspects of hardware selection that are somewhat specific to the coal industry are discussed, and a table of potential areas of application is presented. The dilemma of internal software development is presented and a software development program based on a users group approach is outlined and discussed in detail.

Jan 1, 1983

By William H. Callahan

"For his exceptionally successful career as a geological mentor, for his ore-finding skills, and particularly the discovery of the Central Tennessee Zinc District and for his lecture, 'Prospecting in the USA-Promise and Problems.' " Recipient of the 1982 D.C. Jackling Award

Jan 1, 1983

The "Line of Lade", a generic term by which the great Broken Hill orebodies are collectively known, lies in the County of Yancowinna, New South Wales (NSW) at the south eastern extrenity of the Barrier Ranges. As the township of Broken Hill grew to a city (incidentally it was officially named Willyama but by exerting an enterprising community independence which is still evident today it outplayed officialdom and retained its descriptive name), two major areas of population developed, Broken Hill and South Broken Hill. These two main civic divisions are respectively north west and south east of their dividing line, the surface expression of the orebody. See Fig. 1. The border between the States of NSW and South Australia (SA) is drawn along longitude 1410 East whilst the city of Broken hill's official longitude is 1410 28' 14" East which means it is only 50 km from this political boundary. A latitude of 310 57' 03" South contributes to the harsh climate of high summer temperatures which is not mollified by any significant increase in altitude for Broken Hill is only 300 m above sea level.

Jan 1, 1983

By Dwight L. Sawyer

To provide technology that can help decrease the dependence of the U.S. aluminum industry on imported bauxite, the main ore of aluminum, the Bureau of Mines is investigating the extraction of aluminum from abundant domestic reserves of kaolinitic clay. Miniplant studies of the continuous leaching of calcined kaolin with boiling 25-pct HC1 acid resulted in a 93- to 99-pct extraction of the acid-soluble alumina in the calcined kaolin feed. Data are presented for an acid leaching study carried out in three or four continuously stirred tank reactors (CSTR) in series, feed rates of 100 to 250 lb/hr of calcined kaolin, and total nominal residence times of 0.7 to 2.3 hr. A material balance for a 176-lb/hr calcined kaolin feed rate in a circuit consisting of three reactors, four classifiers, and five thickeners is given. Data provide detailed compositional and physical information for calcined kaolin, process liquors, and acid-leached residue solids.

Jan 1, 1983

By Fred Mosley

The present operation is located on Whitewood Creek about two miles downstream from Deadwood, South Dakota. Early day placer gold operations took place on this creek from Crook City to an area several miles upstream from Deadwood. Early discoveries were in the Deadwood area. In this particular zone, much of the early work was accomplished at stream level and at various elevations above. In the original operations, it was not possible to reach bedrock in many places due to the ground water level plus the existence of numerous large boulders in the same area. The bedrock in this area is approximately twenty feet deep, consisting of Cambrian and Ordovician sediments. Shortly after the early operations began, many small lode mines and several larger mines released mill tailings directly into Whitewood Creek. This practice continued for a full century, thereby limiting the amount of clean water available for sluicing. These tailings in the stream carried large amounts of heavy minerals along with the natural heavier minerals introduced from erosion and were immediately caught in the riffle boxes, resulting in the suspension of many small sluicing operations. No large scale sluicing or mining was ever done at bedrock level in this area, resulting in an almost virgin placer gold deposit. The old tailings cover much of the area, contributing an additional deposit carrying appreciable gold values. In recent years, a company known locally as New Era Mining Company attempted with some success to exploit the area at bedrock level. The equipment used included a Marian dragline with. a three- yard bucket, a washing trommel mounted on a 40 ft by 20 ft floating pontoon barge, together with two banks of Humphrey Spirals and a secondary spiral for collecting concentrate from the two primary

Jan 1, 1983

By Sushil Bhandari

Presented here is the simplified process of fragmentation of homogeneous rocks by blasting based on experimental studies. Small scale single hole blasting experiments on jointed limestone are described. Results show that directions of joints overshadow the degree of fragmentation and also influence the remaining rock. The possible influence of joints on the process of fragmentation of non-homogeneous rock by blasting is also discussed.

Jan 1, 1983