Search Documents

By Byron S. Gottfried, Guan Qi Zhao, John W. Tierney

Equations for predicting the performance of vacuum filters and centrifuges used for coal dewatering are presented. These equations are the basis for a dewatering module which has recently been added to the Coal Preparation Plant Simulator developed at the University of Pittsburgh under the sponsorship of the Department of Energy. The module provides for mechanical degradation in the centrifuge; loss of fines to centrate or filtrate; changes in size and gravity distribution; changes in ash and sulfur content; as well as final moisture content of the dewatered product. Inputs to the module are the flow rate of the coal to be dewatered, a washability analysis of the coal, and parameters describing the operation of the vacuum filter or centrifuge. Typical results obtained using the module are presented. There are adjustable parameters which can be varied to match plant operation or experimental data if desired.

Jan 1, 1983

To provide a means for mechanically separating and recovering nonferrous metals continuously from non-magnetic reject material produced at scrap automobile shredding facilities. Approach The Bureau of Mines developed a water elutriator system that separates metals from shredded scrap auto-mobiles based on differences in specific gravities. A premium-quality product, containing aluminum, magnesium, lead, zinc die cast, copper, copper alloys, and stainless steels, is obtained. How It Works Mixed nonmagnetic reject material currently being separated at automobile shred-ding facilities is introduced onto the top of an upwardly flowing vertical column of water. The water, overflowing a weir in the top of the vertical column, carries with it the floating, lightweight waste materials, mostly combustibles, while the heavier pieces sink through the rising water. Medium-density substances such as glass, rubber, and heavy plastics are carried off through a side port, located in the upper third of the column. The cleaned, mixed metal product sinks to the bottom and is continuously removed from the base of the column with a bucket elevator having perforated buckets. All three categories of material are removed from the system on separate wire mesh belt conveyors. Most of the water drains through the belts into a holding tank and, after settling, is recirculated back through the elutriator column. The purity and recovery of the metal product are influenced by two elutriator operating variables: the flow rate of water through the vertical column, and the height of the overflow weir at the top of the column.

Jan 1, 1983

By D. K. Steele

An 18-in-diam column water elutriator was designed, tested, and operated by the Bureau of Mines for recovering nonferrous mixed metals from automobile shredder rejects. The waver elutriator separated metals from nonmetals contained in shredded nonmagnetic rejects. The unit was constructed and integrated into a local automobile shredding operation. Nonmagnetic rejects from the automobile shredder were fed onto the surface of a column of rising water. Dense materials fell through the rising water and were collected as a sink product at the bottom of the column; medium-density materials were removed as an intermediate product in a water flow through a discharge port located between the overflow and sink; and light materials were immediately carried out in the overflowing water at the top of the column as a float product. Nearly 99 pct of the mixed metals were recovered from the nonmagnetic rejects as a 70-pct-metal concentrate. Other operating conditions yielded a 93.7-pct-pure-metal product resulting in a 93.1-pct metal recovery. Float rejects are combustibles, light plastics, foam rubber, and minimal amounts of coated and uncoated copper wire. The middling discharge contained mainly medium-density rubber, plastics, glass, rock, coated and uncoated copper wire, and frequently some thin-sheet stainless steel and wrought aluminum. Maximum metal recovery in the operating program was achieved using a water velocity of 52 fpm (650 gpm). Maximum purity was obtained with a velocity of 88 fpm (1,100 gpm). .Water was recycled through a 12,000-gal baffled clarifying tank. Entrainment water losses with the float and middling rejects averaged 50 gpt of reject feed. Records maintained by the shredder operator show a 34-pct increase in nonmagnetic metals recovery during a 1-yr operation of the water elutriator as compared to recoveries from a previously used air classification system.

Jan 1, 1983

By Wallace W. Roepke

Research on coal cutting at the Bureau of Mines Twin Cities Research Center (TCRC) has evolved from a purely mechanical approach, specifically to reduce dust or frictional methane ignitions, into an understanding of the complexity of the cutting system relationships. Achieving an understanding of these relationships requires a wide variety of testing techniques and equipment. Laboratory facilities and the associated equipment exist for shallow to deep cutting in both coal and coal-inclusive rock with any desired bit type. Research efforts with this equipment are providing insight for significant advances to help solve the problems of pneumoconiosis and frictional ignition. This effort will ultimately affect both respirable dust and methane ignitions at the face through better bit design and will increase the salable percent of run-of-mine (ROM) coal processed. It will also affect the design of rotary-drum cutting continuous mining machines (CMM) and longwall machines. This report describes the main features of the coal cutting research facilities at TCRC.

Jan 1, 1983

By R. C. Hartviksen

"The Drumbo Mine is a new gypsum mine located at exit No. 32 of Highway 401 between Woodstock and Kitchener, Ontario. The flat-lying 6-foot (1.8-metre) bed of gypsum is near the base of the Silurian Salina Formation, about 380 feet (116 metres) below surface. The mine is owned and operated by Westroc Industries Limited. A shaft, 12.5 feet (3.81 metres) in diameter, was drilled and then lined with a liner-sinking technique new to this continent. The shaft was completed in the fall of 1977. Gypsum production was started in December 1978, employing a conventional room - and - pillar method of mining.Historical BackgroundA brief mention of gypsum in the Drumbo area is included in a survey of the Ontario gypsum industry by Guillet. This occurrence was discovered in 1958 when National Gypsum conducted some widespread diamond drilling. Western Gypsum Products Limited acquired leases in 1960 and concentrated a drilling program in Blenheim Township near the village of Drumbo; 79 holes were drilled in an area of 1900 acres (770 hectares). Mining rights were then acquired for 170 0acres (690 hectares). A test shaft, 44 inches (1.1 metres) in diameter, was drilled to obtain a 50-ton (45-tonne) bulk sample. This opening will be used as an emergency escape way and for ventilation.Westroc Industries Limited, a wholly owned subsidiary of BPB Industries, has its head office at Mississauga, Ontario and operates gypsum board plants at Mississauga, Vancouver, Calgary, Winnipeg and Montreal. Other gypsum mines are at Windermere, B.C. and Amaranth, Manitoba."

Jan 1, 1983

By R. D. Young, E. A. Harre

Nitrogen exists in two broad categories commonly designated as elemental nitrogen and fixed nitrogen. Elemental nitrogen is found in nature as a diatomic molecule and constitutes about 78%, by volume, of the earth's atmosphere. Fixed nitrogen is a common term used for nitrogen that is chemically bound to other elements. Although elemental nitrogen is very abundant, nonleguminous plants cannot utilize nitrogen unless it is in the chemically combined form. The content of this chapter is confined to fixed nitrogen since the uses and properties of elemental nitrogen and the fixed nitrogen compounds are different. Certain bacteria associated with legumes are able to fix atmospheric nitrogen, but not to the extent required by succeeding nonleguminous crops. The need to use fertilizers containing fixed nitrogen compounds to grow food crops has been recognized for hundreds of years, and from antiquity farmers have used organic wastes such as animal manures, vegetable wastes, sewage sludge, fish scraps, etc., containing these compounds for fertilizers. These organic materials have a low nitrogen content, however, and cannot support large-scale food production. Known commercial-size deposits of natural nitrates containing much higher nitrogen content exist only in Chile, and the possibility of the discovery of other significant deposits is remote. The Chilean deposits were the major source of nitrogenous fertilizers until the Haber-Bosch process for the production of synthetic ammonia was developed. In the Haber-Bosch process, nitrogen reacts with hydrogen at high temperatures and pressures and in the presence of a catalyst to form ammonia. Modern plants use air, water, and natural gas or other hydrogen sources to produce the ammonia that is now the key building block of the fixed nitrogen industry. Several major problems that developed in the 1970s continue with the nitrogen industry into the 1980s. These are (1) the continuing sharp escalation in the cost of feedstocks for ammonia production as well as all energy sources, and (2) the very steep increase in the investment cost of production facilities. More than 75% of the fixed nitrogen produced domestically is consumed as fertilizers. The types of materials used as fertilizers have changed significantly during the past years. There has been a trend from the use of low-analysis fertilizers to types which contain high percentages of plant nutrients. The average plant nutrient content (N + P2O5 + K2O) of fertilizers used in the United States has increased from 18% in 1930 to 32% in 1960 and today approaches an average of 44%. In the case of nitrogen fertilizers, the low analysis natural nitrates (16% N) gave way to ammonium sulfate (20% N) after about 1920. After World War II, ammonium nitrate (33.5% N) previously used in munitions, became established as the leading nitrogen fertilizer. Urea use as a fertilizer (46% N) began in the 1960s, and in the past 10 years has become the world's leading solid nitrogen fertilizer. Nitrogen Materials Anhydrous Ammonia-Anhydrous ammonia is a colorless gas at ambient temperatures and pressures and has a sharp pungent odor. Anhydrous ammonia is stored and transported as a liquid in high-pressure cylinders and tanks at ambient temperature, and in low-pressure tanks, barges, and ships at -28°F. Anhydrous ammonia is applied directly at 4 to 7-in. depths in the soil as a high-pressure liquid by special applicators, after which it expands to a gas that dissolves in the soil moisture or is absorbed on soil colloids. In other systems ammonia is metered into irrigation water and is thereby introduced into the soil.

Jan 1, 1983

This paper reviews factors involved in the feasibility stage of underground mine project development. Emphasis is placed on the need to first select the best method of extraction and make the most accurate assessment of the expected output even with the uncertainties which may exist in structural interpretation, ground stress, geotechnical factors, and industrial conditions. The subsequent engineering planning should be undertaken from the point of view of the face requirements and is subject to constraints imposed by the method of work and nature of the deposit and, in the case of access, to surface constraints and services.

Jan 1, 1983

By Lu Yang

In the last two decades, acid iron ore pellets have established their predominant position as the iron-bearing burden material for blast furnace ironmaking in North America. It is a general practice that pelletization plants are asked to produce pellets of certain chemical composition and in a narrow range of sizes. A minimum amount of fines created during handling and transportation is desirable. Such a requirement is often expressed indirectly by the minimum compression load causing a pellet to break. The behavior of pellets inside a blast furnace, of course, is very important for a smooth and efficient operation. Before its melting in the lower part of a blast furnace during this period of several hours the behavior of pellets depends on their properties after induration as well as conditions inside each furnace. Among properties of indurated pellets, the ability to maintain their physical integrity in the burden and to be reducible are most important. To maintain the integrity of pellets (i.e., minimal low temperature breakdown, swelling and softening) so that there will be adequate overall permeability for certain wind rate and local permeability for gas/solid contact for reduction. A higher reducibility will moderate the adverse effects of swelling and softening and contribute to a smooth operation and efficient use of heat and reductants in a blast furnace. An article devoted to the relationships between the quality of iron ore pellets and blast furnace practice has been published elsewhere(1); therefore, no further discussion is needed here. The mechanism of strengthening of iron ore pellets during firing has been the subject of investigation of many authors(2). There is no doubt that the bridging of the growing hematite grains, particularly starting with magnetite concentrates, is very significant in the production of strong pellets. Recently, there are many reports from blast furnace operators that they have noticed the adverse effect of LTB in their plants. It is obvious that the strength derived from bridged hematite grains may disappear when hematite is converted to magnetite with thorough breakdown of grain structures. It is suggested that some other strengthening mechanism may be required in order to improve the LTB index of acid pellets. The influence of porosity on both compression strength and reducibility follows regular patterns. It has been suggested(1) that the amount of liquid slag in pellets during firing determines to a large extent the porosity, hence, indirectly, strength and reducibility.

Jan 1, 1983

By Scott G. Britton

This chapter is concerned with the construction of the dynamic component of belt haulage systems. The dynamic system includes the belt line and tailpiece extension and retraction movements in a production system where mine management is continually placing the belt in the most effective operating position. Correct installation of the belt and tailpiece during an extension is very important for many performance reasons. Two of the most important reasons are to eliminate spillage and safely operate the belt line. This chapter is divided into three major discussions. The first discussion looks at analyzing the parameters of effective belt line construction. This includes a review of the parameters and management tools needed for proper scheduling of a move-up. The second major discussion topic centers on efficient procedures for a belt line extension. Topics such as site preparation, tailpiece breakdown and setup, stringing the belt line and structure, plus operating and maintenance tasks needed after the belt line is installed and running, are covered. The third discussion presents a list of conveyor and conveyor component manufacturers who provide services and products to the coal mining industry. Again, any discussion on underground haulage systems must generalize much of the site specific design approaches to be practical. This text will mention, where applicable, some of the alternatives available to construction engineers in designing belt line systems.

Jan 1, 1983

By W. G. Prast

Investments in fuel minerals and non-fuel minerals by petroleum companies are not a new phenomena. During the past 25 years, oil firms have entered mining via the acquisition route as well as by the direct development of grassroots mines. In the early 1980s, the "merger mania" in the natural resource industries came to a head. Oil company takeovers of mining firms, as well as other mergers between oil producers, captured headlines repeatedly, and speculation ran wild as to who would next acquire whom. Table 1 summarizes leading mining company mergers in the past two decades. There are some special features to the latest round of minerals investments undertaken by oil companies. First, direct takeovers of mining companies have become the preferred means of entry into minerals, with entry from scratch being relegated to the sidelines. This was not always the case. While there are instances of oil firms buying coal and copper companies dating back to the 1950s and 1960s, most of the early minerals work by petroleum firms was from internally generated projects. When the oil companies first became involved in uranium, for example, the uranium mining industry was in its infancy. There was not much market structure to buy, and it was relatively easy for everyone to get into uranium on the ground floor.

Jan 1, 1983

By W. C. Meyer

In an effort to conserve and extend oil resources, the use of powdered coal-in-oil mixtures (COM) as an alternate fuel in oil-fired boilers is receiving increasing attention. For the approach to be successful, some degree of stability of the suspension against settling is needed. The variety of means available to achieve stability of this nonaqueous slurry is reviewed along with some of the physical and chemical concepts which underlie each method.

Jan 1, 1983

By W. W. Svendsen, J. F. Hoffmeister, W. C. Larson, R. E. Cozad

The paper presents the background, history, and current development of the retractable core bit for the wireline drilling system. Design criteria, concept development, and system design of the retractable bit system are discussed, including laboratory test results.

Jan 1, 1983

By Eric Ohl

Due to the world's ever increasing minerals and energy demands, process plants have to cope economically with ever growing throughput rates. This trend has accelerated the development of high capacity vibrating screens. Screens with screening areas of 30 to 50 square meter (322 to 540 square feet) and width of 5.5 meter (18') are technically possible and are being used presently with great success. This paper will concern itself with the general aspects of large screen design, by using modern technology and the latest findings with regards to fatigue strengths relative to the laws of vibration. It also will investigate the technical and economical limits of such designs.

Jan 1, 1983

By Roy L. Zuber

Identification and analysis of mining hazards involves the correlation of accident, injury and illness information from all segments of the mining industry. It would not be feasible to process the volume of data involved without substantial reliance upon a computerized information system similar to that maintained by the Health and Safety Analysis Center. Numerous statistical programs are applied to the computerized accident-injury-illness data base to identify those mining tasks and associated activities which are responsible for most of the injuries and occupational illnesses. These programs are used to flag those mining tasks or conditions at specific mines or segments of the mining industry where either a significant increase in the injury/illness trend has been reported or where the number of injuries/illnesses related to specific mining tasks or conditions are high. Upon identification of those mining hazards which warrant further analysis, a computerized search of the coded accident data is performed to correlate the predominant categories by cause of injury or illness, source of injury, nature of injury, type of accident, etc. From this correlation, those factors most common to the conditions responsible for the hazard may be identified. Based upon analyses of this form, recommendations are made regarding the appropriate engineering, training, and/or operational improvements necessary to alleviate the hazard. In addition to mining hazard analysis, the computerized data base also has application in the area of optimum resource allocation. Computer programs have been developed to assist management in allocating resources based upon organizational requirements and historical accident - injury trends.

Jan 1, 1983

My speech this morning is not a technical one, rather I will aim to tell you about the New Zealand Aluminium Smelters Limited and how I see it fitting into the Western World aluminium scene.

Jan 1, 1983

By Gilbert Sauriol

The mining complex, which the Mines Gaspé division of Noranda Mines Limited has operated in Murdochville since 1954, includes open pit and underground mines, two mills, one leaching plant and a smelter. The under- ground mining uses predominantly a large scale room and pillar method, rooms 15 m wide, 30 m high and 300 m long being common. Ore production is effected by 4.5 m3 front-end loaders and 32-tonne trucks powered respectively by 225 and 325 kW diesels. Daily dust and gas readings show that air quality can be maintained at an acceptable level with much less ventilation than that normally specified. This paper emphasizes the point that air requirements should be based on Air Quality Standards, thus allowing an operation to benefit from favourable conditions or from improvements such as exhaust treatment, fuel alteration, etc.

Jan 1, 1983

By Angelus S. C. Owili-Eger

The investigation into the hydrologic and hydrogeochemical influence of longwall coal mining in the Appalachian coal basin was under- taken in response to the need to technically address problems of damaged or impaired well yields, and quality deterioration. Prior to this study, issues regarding reduced aquifer yields and degraded water quality had to be handled in a very qualitative manner. Such an approach would, in the long run, claim a heavy toll on the mining industry. The primary objective of this undertaking, therefore, was to provide sufficient and reliable information base for the determination of the local and possibly the regional effects of longwall mining on well yields, and the hydraulic and hydrogeochemical parameters of the immediate surface and subsurface water systems. Specifically, the program was designed to supply definitive data to answer the following series of questions: 1. Does longwall mining affect the quantity and quality of water in local wells above and adjacent to longwall panels and barrier pillars? 2. If the water quality is affected as soon as mining takes place, does it heal? or if it is not affected immediately, does it change over a longer period of time? 3. How do the aquifer water transmitting characteristics respond to induced physical ad hydrologic variations? 4. What is the extent of the various changes in quantity and quality of the water resources? 5. Should and can standard hydrologic evaluation techniques be used to determine the hydraulic properties of highly fractured zones located within a larger and less permeable aquifer?

Jan 1, 1983

By Hasan Sevim

This paper summarizes recent developments in modeling of underground coal slurry haulage networks for determination of optimum design and operating parameters. The model presented here is based on a stochastic dynamic programming formulation, applicable in any typical room-and-pillar and/or longwall mining configuration commonly practiced in the United States. The formulation and the structure of the model is general enough to handle design problems involving more than one face and mining method. Given the stochastic operating characteristics and a system layout, the model can be used to determine the equipment configuration and operating regimes that minimize the overall unit cost of coal haulage.

Jan 1, 1983

By Weller KR

Computer programs are described which help the metallurgist to process sample data from a plant survey; to carry out simple mass balance calculations; to present the results of circuit and equipment performance in convenient form; and to simulate the circuit response to changing operating conditions. The uses and limitations of these programs are explained by following through a case study of the sulphide flotation circuit at Cleveland Tin Ltd. The circuit was sampled, the data analysed, and some process inefficiencies established. Simulation calculations were then made to provide information on which to base decisions regarding possible circuit changes aimed at improving performance.

Jan 1, 1983

By James L. Evers

The development of hydraulic mining in the United States has had an uneven record of progress. The shifting of coal extraction from one government agency to another has not provided an environment for a focused national research program. This paper presents an update on hydraulic mining research in the United States. A comparison is made between the development of the technology in this country and the state of the art in other parts of the world.

Jan 1, 1983