Search Documents

By Donald O. Capstick

A mineral resource evaluation of the Coyote-Southeast RARE II area (No. 5033) was performed jointly by the U.S. Bureau of Mines and the U.S. Geological Survey in 1981 for the U.S. Forest Service RARE II program. Bureau of Mines personnel conducted a mineral resource inventory of the study area's mines, prospects, claims, and mineralized outcrops. The study area's boundaries encompass 51,700 acres on the east flank of the Sierra Nevada and are within Inyo National Forest southeast of the city of Bishop in east-central California. Cretaceous granite underlies most of the area; the remainder of the rocks are metasedimentary. At the contact of the two, tactites formed at many places where carbonate rocks were present; replacement processes produced local scheelite (calcium tungstate) occurrences.

Jan 1, 1983

By Bing W. Jong

A bench-scale evaluation of coal and coal waste materials as aggregate materials for use in longwall mine supports was undertaken as part of the Bureau of Mines Health and Safety program on ground control. Performance data were obtained on portland cement concretes (PCC) prepared with coal and coal wastes as aggregate materials. The effects of high-early-strength accelerators on strength and creep and of superplasticizers on strength properties of PCC formulated with coal and coal waste were investigated. Concrete formulated with a high-early-strength accelerator and coal and coal waste has 20 and 40 pet greater compressive strength, respectively, than the control samples without admixture. A concrete formulated with coal waste and the high-early-strength accelerator, using four bags of cement per cubic yard and a water-cement ratio of 1.0, had the lowest creep value of all the coal- and coal-waste-formulated PCC's tested.

Jan 1, 1983

By Reimers. Jan H.

Practically all the world's lead is produced by sintering and blast furnace smelting, or the Imperial Smelting Process which is a variant of the blast furnace process. Increased coke and labour costs and strict lead emission limits have, however, made blast furnace smelting undesirable in most countries. A change-over to other lead smelting processes providing better working conditions and lower emissions is, therefore,. expected to occur once economic conditions improve and the necessary capital expenditures can be justified. The need for new lead smelting processes has long been evident and a number of new processes have been proposed 'and advanced to various stages of development. One of the new processes is already proven on commercial scale, while several others are still being tested on pilot plant scale.

Jan 1, 1983

By J. Frostiak

"This paper describes some energy reduction measures Implemented at the Griffith Mine. Before proceeding, I will give you a brief overview of the operation.The Griffith Mine is an iron ore mining, concentrating and Pelletizing complex located in the red lake area of northwestern Ontario. The operation is owned by Stelco Inc. And is managed By Pickands Mather & Co. of Cleveland, Ohio. Operation of the concentrator commenced in 1968 and it has been producing at a nominal capacity of 1,500 ,000 tons annually.The plant flow sheet is illustrated in this slide. Run of the mine ore is crushed in a single stage 54"" gyratory crusher. Reclaim ore feeders draw from an open stockpile to feed two 32' diameter by 12' long autogenous mills, each driven by 6800 hp. Two s·rages of wet magnetic separation, roughers and cleaners, and primary cyclones complete the primary circuit. Cleaner concentrate is then ground in four 14' diameter by 28' long pebble mills rated at 2000 hp. The secondary grinding circuit is closed by cyclones and fine screens. Secondary cyclone overflow is further upgraded through hydro-separators, finisher magnetic separators and flotation.The magnetic concentrate produced is then thickened, filtered, balled and fired in three vertical shaft furnaces to produce a high quality hematite pellet."

Jan 1, 1983

By Robert H. Lambeth

There are no identified mineral resources in the Italian Peak RARE II areas, and there are no producing or developing mines within or adjacent to the study area. Several prospects are in RARE II area M-4945, Idaho, but none were found in the area I-1945, Montana. The Viola Mine (fig. 1, no. 15) vicinity and the Heart Mountain vicinity along the west and south borders, respectively, are being prospected. There has been no recorded production from mines within the study area, but between $2.5 million and $5.0 million worth of lead, silver, and zinc were produced in the adjacent Birch Creek district - dominantly from the Viola Mine - from 1882 to 1889 (Anderson and Wagner, 1944, p. 14). The Viola and other mines in that district are possibly, on basin-margin, carbonate-hosted, lead-silver-zinc deposits stratabound within the Devonian Jefferson Formation. Previous studies have considered them to be hydrothermal, replacement orebodies. Mineral occurrences in the Heart Mountain area are possibly black-shale hosted uranium-vanadium deposits in the Mississippian-Devonian McGowan Creek Formation or perhaps the underlying Devonian Three Forks Formation. The Jefferson and McGowan Creek Formations underlie many scattered segments of the study area. The deposits and occurrence; are not sufficiently exposed to determine tonnage and grade, but sampling indicated moderate resource potential at two properties just outside the study area, the Viola Mine and the Elkhorn Group (fig. 1, no. 33). Local residents indicated there are several thousand tons of zinc-bearing resource; at the Viola line. A 23-ft (70-m) drill hole intercept near Heart Mountain et the Elkhorn Group adjacent to the stuny area contained 0.15 percent uranium oxide

Jan 1, 1983

By B. R. Schneiders

"Atikokan is 200 km west of Thunder Bay and earned its mining fame from the discovery of the Steep Rock Iron Range in the late 1930s. Gold, however, was discovered in the Atikokan and Mine Centre areas in the late 1800s and eventually led to one of Ontario's first gold camps, and a total production of approximately 52,000 oz of gold and 174,000 oz of silver from 218,000 tons milled.The general geology of the area consists of Early Precambrian rocks of the Wabigoon and Quetico subprovinces, separated by the east-trending Quetico Fault. The Wabigoon Subprovince, to the north, consists of metavolcanics, minor metasediments and granitic batholiths. The Quetico Subprovince consists of metasediments and granitoids. Small ultramafic plutons occur throughout the metasediments.Within a 50-km radius of Atikokan, more than 50 gold occurrences, prospects and past producers have been discovered since the 18oos. The Atikokan Gold Study performed by the Ontario Geological Sur vey (Wilkinson, 1980, 1982) defined three types of gold mineralization in which gold is concentrated in quartz and quartz-carbonate veins:I) Metavolcanic-Hosted, Stratabound Type-associated with altered felsic fragmental units and chemical sedimentary rocks; possible gold mineralization source rocks. The mineralization is due to metamorphogenic (epigenetic) enrichment. Associated with dynamic metamorphism events and/or felsic intrusive events.2) Marmion Lake Batholith Type-occurs within the gneissic core of the batholith associated with north east-trending lineaments, representing faults or shear zones. Mineralized veins are related to several periods of deformation and shearing, suggesting that metamorphogenic veins were produced during dynamic metamorphism.3) Contact Zone Type -occurs in the contact zone rocks between gneissic batholiths and meta volcanic belts. Hydrothermal solutions produced during several deformational periods acted to leach and concentrate gold mineralization. Localized, discontinuous shear zones host the epigenetic (metamorphogenic) veins.Twenty-one properties in the area were mapped and sampled, and researched petrographically and geochemically. Geological data from the Atikokan Economic Geologist Program of the Ontario Geological Survey are used in discussing the types of mineralization, genetic models, and exploration targets and techiques."

Jan 1, 1983

By Jack A. Caldwell

"This paper describes the nature of stage curves and the ways in which they have been used to study the construction sequencing of tailings impoundments. They provide a simple graphical method of representing the main aspects of an impoundment, studying the effects of different impoundment geometries, and predicting and controlling impoundment operations.IntroductionThe designer o f a tailings impoundment must, at all stages of design, examine the relations hip between the volume o r tones of tailings that will be deposited at the impoundment, the height to which the tailings will rise in a given time and that rate at which the various parts of an impoundment will be constructed. The operator, if he is to keep proper control of this impoundment, must be able to examine the effect of different deposit ion rates at the impoundment, and the consequences of placing more or less tailings at different parts of the impoundment. The operator must be able to see at a glance just how much higher an impoundment will be at the end o f the following yea r of deposition, and this he must be able to do in order to formulate his annual construction and operating plans.Stage curves are the best way o f modeling an impoundment. The simple impoundment model represented by the stage curves enables the designer and operator visually to examine the relationships between the various factors, such as impoundment volume, deposition rat e and construction rate, that dictate the essential features o f impoundment design and operation.A design model for a tailings impoundment may be formulated as in Figure 1. This involves the site selection process, the definition o f a geotechnical model, a water balance model and a height-capacity-production model."

Jan 1, 1983

By Frederick V. Lawrence

Broadly speaking, fluxes are substances which promote wetting and spreading or enhance the fluidity and manipulative properties of materials in joining, fusion, and smelting operations. The term most strictly applies to substances used to facilitate soldering and brazing; but in the discussion which follows, the definition will be broadened to include materials used to promote fusion in arc welding and which aid in the smelting of metals. In each of the mentioned applications, the role of flux and its composition differs considerably; consequently in the discussion which follows, fluxes for soldering, brazing, arc welding, and smelting applications will be considered separately. Soldering and Brazing Fluxes Soldering and brazing are metallurgical joining processes in which a joint is formed using a filler metal of composition dissimilar to that of the joined pieces (base metal). The filler metal, solder or braze, is always of lower melting point than the base metal. Consequently with these processes there is no melting of the base metal. The successful creation of the joint depends upon the wetting and spreading of the solder or braze around or throughout the joint. The obstacles to successful soldering and brazing are contaminants and tenacious oxide films on the metal surfaces. In soldering and brazing applications, fluxes act to remove and exclude oxides and other impurities from the joint. There is no fundamental difference between soldering and brazing. The distinction between them is made on the basis of temperature. Join¬ing operations carried out at temperatures above 500° C are termed brazing. The higher temperatures used in brazing enable higher melting point filler metals to be used which generally provide stronger joints. The higher temperatures of brazing processes also require fluxes which are substantially different from those used in soldering and which will remain effective at high temperatures. Consequently the distinction between soldering and brazing can also be made on the basis of the fluxes used. Soldering Fluxes Even thoroughly cleaned and degreased, metal surfaces still possess tenacious oxide films which inhibit the soldering of the joint. The reactions which form these films increase with increasing temperature. The rate of oxide formation and the tenacity of the film varies with each base metal. Aluminum, magnesium, stainless and high alloy steels, aluminum and silicon bronzes when exposed to air form hard, adherent oxide films. These metals require highly active and corrosive fluxes to remove and prevent the reformation of oxide films during soldering. Metals such as copper and silver, on the contrary, form less tenacious films at a lower rate, so that mild fluxes are sufficient. Soldering fluxes must dissolve or remove oxides and promote rapid wetting and spreading of the solder. The flux removes the oxide film by loosening and floating it off into the main body of the flux. The oxide removal is often aided by the alloying of the solder with the base metal, undermining small areas of the oxide and detaching them (Anon., 1959). The flux coagulates and suspends the oxide particles which have been loosened. The flux forms a protective cover preventing the reformation of the oxides, permitting the spreading of the solder and the formation of a metallic bond between the solder and the base metal. Constituents of Soldering Fluxes: Soldering fluxes are commonly grouped into three categories: highly corrosive, intermediate, and noncorrosive. One normally would choose to use the least corrosive flux which will give satisfactory performance.

Jan 1, 1983

The following pages contain valuable information about the products and services offered by our advertisers

Jan 1, 1983

By B. G. Long

Coastal States Energy Company (Coastal), a wholly-owned subsidiary of The Coastal Corporation of Houston, Texas, owns coal mining operations in Utah and Kentucky. One of the Utah operations, Southern Utah Fuel Company (SUFCo), located 30 miles west of Salina, Utah, has been operated by Coastal since 1974. This operation is a single-seam, six-section mine operated from one portal area. It produces 2.2 million tons of coal per year and has a payroll of approximately 300 employees, Coal is mined by continuous miners, hauled by diesel-powered haulers and transported by belt conveyor to outside crushing and screening facilities. Sized coal is hauled by contract truckers 80 miles to a unit-train facility located at Levan, Utah.

Jan 1, 1983

By I. Iwasaki

A low-grade copper-nickel deposit, with an estimated size of 4.6 billion tonnes and with average analyses of 0.6% copper, 0.2% nickel, occurs in northeastern Minnesota. In addition to copper, nickel, cobalt, and precious metals, the Duluth gabbro contains magnetite, ilmenite, olivine, plagioclase and biotite. It is estimated that the flotation tailings that would be produced by a concentrator of optimal size to sustain a smelter would amount to 20 million t per year. The flotation tailings, having already been ground, warrant a closer examination for the recovery and utilization of potential by-products. The residual sulfide minerals and fibrous minerals may also be isolated and treated separately for useful purposes or for disposal in an environmentally acceptable manner. Two flowsheets were developed; one involving preconcentration by low- and high-intensity magnetic separation and another involving preconcentration by gravity concentration. The concentration methods for recovering and purifying individual by-product minerals were investigated. From their chemical, physical and mineralogical characteristics, the potential areas of application and marketabilities of each product fraction were surveyed.

Jan 1, 1983

By G. B. Atkinson

The Bureau of Mines, in cooperation with McDermitt Mine, investigated a method for recovering mercury metal from mercury sulfide flotation concentrate by a hydrometallurgical technique. This preliminary report shows the feasibility of leaching mercury with a cupric chloride solution and electrowinning mercury from the solution. Proposed chemical reactions are shown in equations 1 through 3: 2CuC12 + HgS + 2CuCl + HgC12 + S°; (1) electrolysis HgC12 ?Hg + C12; (2) 2CuC1 + C12 ? 2CuC12. (3) A bench-scale leaching-electrowinning apparatus capable of treating 2.36 kg of sulfide concentrate in 11 days was operated continuously. An acid chloride solution containing, in grams per liter, 70 Ca, 60 Cu, 30 Fe, and 80 Hg was used as both leachant and electrolyte; 99.5 pct of the mercury was solubilized from the sulfide concentrate. Electrolysis of the leaching solution recovered mercury metal at an average current efficiency of 32 pct and an average energy consumption of 1.2 kwhr/lb Hg. Results from a preliminary economic evaluation indicated that a plant producing 31,500 flasks of mercury per year would have a capital cost of $3.7 million and an operating cost of $62 per flask of mercury.

Jan 1, 1983

By Howard M. Wells

Portfolio theory and the Capital Asset Pricing Model (Modigliani and Pogue, 1974) provides an investment decision rationale which takes account of the benefits of diversification in reducing effective risk, but this theory does not consider the financial capability of the firm to survive large losses if they should occur. The LL-curve theory (Wells, 1976) takes the latter consideration into account, but it does not provide for the effects of diversification. This paper pro- poses a general theory to account for both diversification and the financial capacity of the firm to underwrite the investment risks.

Jan 1, 1983

By Roy L. Klein

The production of synthetic fuels from coal has been pioneered by South Africa. South Africa made a decision in 1975, due to the threat of an oil embargo, to proceed with the construction of Sasol Two, then followed by Sasol Three. South Africa has large coal but little indigenous petroleum reserves. The indirect coal liquefaction process used by Sasol since 1955 is the only commercially demonstrated method available for producing transport fuels from coal. The new plants consume 27 million tons per year of coal from a single mine that now produces transport fuels in sufficient quantities for energy independence.

Jan 1, 1983

By G. R. Peterson

To determine the availability of aluminum from world bauxite resources, the Bureau of Mines investigated 139 bauxite deposits worldwide and evaluated the potential production of aluminum based on the demonstrated resources of bauxite ore from 91 mines and deposits in 22 market economy countries. The demonstrated resources of the bauxite mines and deposits included in this study represent an in situ resource of 20.2 billion metric tons of bauxite. Total identified bauxite resources in market economy countries amount to roughly 31.9 billion tons. Of the demonstrated resource, some 18.8 billion tons of bauxite considered minable provide a production potential of 3.6 billion tons of primary aluminum. Given the wide geographic distribution of bauxite deposits, stable supplies of bauxite for aluminum production seem assured well into the next century. However, a tight market situation could develop during the 1990's unless the real price of aluminum increases enough to stimulate massive new investments in production capacity, particularly in refining and smelting. This study indicates that a real price of at least $0.85 per pound (in January 1980 dollars) would be necessary to stimulate the required investments and provide a sufficient rate of return on invested capital.

Jan 1, 1983

By Mike S. Ness, Allan G. Provost

High speed drilling, mucking, and hauling equipment was used in driving approximately 2.16 km(7100 ft) of lower power tunnel in quartz diorite for the Tyee Lake Hydroelectric Project near Wrangell, Alaska. The .91 m(36 in.) guage rail mounted equipment included a Tamrock 2-boom electric/hydraulic drill jumbo, a Haggl and 8HR mucker , and 3 Hagglund 115C shuttle cars. Several other innovative techniques allowed maximum advance rates of up to 17.5 m/day(57ft/day) in the 3 m(10ft) horseshoe section. Average tunnel advance was approximately 11 m(day(35.4 ft/day). The primary difficulties preventing full utilization of the equipment potential were the operators' "learning curve", the need for complete retraining of all personnel in the new methods, and minor sections of faulted ground.

Jan 1, 1983

By Michael A. Redfearn

The use of nitrogen in molybdenite flotation circuits is a relatively new concept utilized by only a few mines around the world. This paper briefly discusses circuit chemistry and the reason for its success. It follows the entire testing process which resulted in a sodium hydro-sulphide dosage reduction from 18.5 to 4.4 lbs/ ton (9250 to 2200 g/t) through to the final installation of an inert gas generator which will produce reagent savings in excess of one million dollars annually. A description of the various types of nitrogen generators commercially available is included.

Jan 1, 1983

By Mehmet Guney

[The Atlantis-II-Deep is a hydrothermal mineralization located along the median valley of the Red Sea at a water depth of about 2200 m. Extensive exploration of the metal-rich brine deep revealed a potentially mineable deposit on economic interest consisting of oxides, silicates and sulphides with considerable concentrations of zinc, copper, cadmium and silver. Geostatistics was applied to assess the most likely in-situ vague of the metal potential for economical exploitation. Semi-variograms were constructed to characterize the structure of the regionalized distribution of the geological parameters. Volume grades and thicknesses were determined by the kriging technique, avoiding systematically biased high or low grades, and then block .tonnages were computed. The estimation variances, distribution of errors and histograms of observed and kriged values in each grid Mock were also produced.]

Jan 1, 1983

By George K. Schenck

INTRODUCTION Recent advances in high-pressure water jet technology can be effectively employed in mining and tunneling. The new equipment is based on available industrial hardware such as pumps, nozzles, and rotary swivels and seals, and is compatible with present mining and tunneling techniques. Principal advantages of water-jet assisted cutting relative to standard cutting are higher production rates, lower dust levels, and reduced fines. When used on rock and coal miners, water jets mean that relatively smaller and cheaper machines can be purchased. If properly applied, the combined effect is lower cost and significantly improved health and safety. While commercial use of high-pressure water blast cutting and extraction of rock (and concrete) already has a firm foothold in Europe, application of this new technique is just beginning in America. This paper begins with current American applications of high-pressure water jets for drills, for slotting and channeling machines, and then discusses the emerging technology for initiating rock failure in conjunction with drag bits on coal plows, continuous miners and boom-type miners (roadheaders). The focus of this paper is use of high-pressure water jets for cutting rock. High-pressure water jet cutting utilizes water above 70 MPa and currently reaches to 300 MPa and above. Some informatfon is included on low pressure "wethead" coal shearers and boom miners with water pressure to about 15 MPa.

Jan 1, 1983

By L. F. Mashburn, T. J. Ferree

A Reichert cone concentrator was installed in an aggregate plant circuit to recover the extremely fine "flour gold" known to exist in the deposit. The gold content of the bank- run gravels averages about 0.1 g/t-about $1.29/t, based upon $12.86/g ($400 per oz) gold. The fineness of the gold averages between 950 and 960. The Reichert cone, in conjunction with a conventional shaking table, recovers in excess of 85% of the gold. A screen analysis of the gold particles shows 44.1 % is - 74pm (-200 mesh) in size. The plant operates with a two-man crew.

Jan 1, 1983