Search Documents

By John S. Egbert

Many of you are familiar with the Washington Metro Project. However, inasmuch as some may not be, and others may want to refresh their memories regarding certain facets of the project, I will cite a few summary details about the rail transit system we are constructing. That summary will also give each of us a common point for departure as I develop the principal thoughts that I want to leave with you. The Washington Metropolitan Area Transit Authority (WMATA) is an interstate agency established by Compact between the District of Columbia, Maryland and Virginia and approved by the United States Congress. Currently, the Authority has approval to build and operate a 101-mile (162.5 km) regional rapid rail transit system as shown on Appendix A. Of that total, 38 miles (61.2 km) will be in D. C., 32 miles (51.5 km) in Maryland and 30 miles (48.3 km) in Virginia. (Mileage figures, because of rounding error, do not add to 101 miles.) Referring again to the 101-mile total, 48 miles (77.2 km) will be underground, 42 miles (67.6 km) on the surface and 10 miles (16.1 km) on aerial structures. Of the 48 miles (77.2 km) that are underground, 15 miles (24.1 km) are rock tunnel, 14 miles (22.5 km) are earth tunnel, 0.5 miles (0.8 km) 9.s sunken tube and 19 miles (30.6 inn) are cut-and-cover construction. The system will include 86 stations, with 51 of them underground. Referring again to the full 86 stations, 43 will be in D. C., 23 in Maryland and 20 in Virginia. We currently have 37 miles (59.5 km) of line and 41 stations in operations as shown on Appendix B. Also shown on Appendix B is another 16 mile (25.7 km) increment and 13 stations which have been substantially completed, but are not yet in service. Additionally,

Jan 1, 1981

By L. Barry Phelps

Coal mine drainage, which occurs predominantly as acid mine drainage in the East, is a serious contaminant of surface and groundwater systems (Appalachian Regional Commission, 1969). Treatment of this pollutant can be very costly and is often difficult to achieve (Appalachian Regional Commission, 1969). A major source of coal mine drainage in surface waters is polluted ground- water discharge, therefore treatment of surface water does little to combat groundwater contamination. Prevention of the formation of coal mine drainage and restricting its entrance into the groundwater protects both surface and groundwater systems. The formation of acid mine drainage may be inhibited by preventing contact between toxic spoil, air, and water (Grim and Hill, 1974). This may be accomplished by surrounding toxic spoil with a relatively impermeable barrier, thus restricting groundwater and oxygen flow through the toxic zone. Toxic spoil packages constructed in this manner would minimize the entrance of acid mine drainage into the groundwater system, allowing dilution by uncontaminated water to occur. If successful, concentrations of coal mine drainage would be reduced below toxic levels.

Jan 1, 1981

By A. N. Brown

This title of is not that originally chosen for the Colloquium, which was 'A high gold price'. Such a title would have been unfortunate because it would have related the Colloquium only to the high gold price of the past two years, which reached the dizzy peak of 850 dollars per ounce in January 1980. The chosen title is, of course, the right one because it places the whole problem in the right perspective. It relates to a situation that has occurred many times before. Over the course of the past century, the gold price has periodically been inhibited from rising, so that it has undergone a succession of stepwise increments. With each increase, the relationship of the working cost to the gold price alters, and gives rise to a jump in ore reserves. Award for CMI fuelling technique Consolidated Metallurgical Industries Limited - the Lydenburg-based ferrochromium producer in the J.C.I. group - was one of the five recipients of the 1981 National Productivity Institute annual award.

Jan 1, 1981

By Richard H. Singleton

Native asphalt was produced in 1980 by six companies in four States. Leading States were Texas and Utah. Output decreased 22% in 1980 to 1.25 million tons while value decreased 2% to $25.0 million. Bituminous limestone was produced by Whites Uvalde Mines and by Uvalde Rock Asphalt Co. in Uvalde County, Tex.; by Southern Stone Co. in Colbert, Ala.; and by Barton County Rock Asphalt Co. in Barton County, Mo. The product was used mainly in street and road repair. Gilsonite was produced by American Gilsonite Co. in Uinta County, Utah, and by Ziegler Chemical and Mineral Corp. in Weber County, Utah. This material was used for purposes other than road repair.

Jan 1, 1981

By D. N. Trerice

The Electric Power Research Institute (EPRI) is sponsoring the construction and operation of a coal cleaning test facility at Homer City, Pennsylvania. The facility represents a major investment by the electric utility industry to advance the state of the art of conventional coal cleaning technology. The facility is unique in design and can process large quantities of coal in conventional flowsheet configurations, simulate full size plant conditions, and perform open and closed loop performance testing on conventional and advanced coal cleaning equipment. Computer operation will also be demonstrated. The facility objectives, initial complement, and operating plane are discussed as they relate to other coal cleaning projects at EPRI.

Jan 1, 1981

By R. E. Blair

The economics of the producer-consumer interface - the route from mine to market - impact much more severely on specialty industrial minerals, extender/fillers that have to be sold, than on commodity industrial minerals that are basically supplied. Working capital costs for inventories and accounts receivable, fixed capital costs for storage/ warehousing/distribution, and sales and marketing costs all make the extender/filler producer much more of a marketer than a miner. The future survival of an extender/filler producer will primarily depend on the skill he has in the economics of the interface.

Jan 1, 1981

By Franklin J. Kay

Introduction The methods used in surface, mining vary throughout the world, depending on many variables such as: the types of over- burden materials, the depth of the overburden, the thickness of the seam, and other operational choices, both financial and functional. However, the stripping machines are typically draglines, stripping shovels, excavators, scrapers, loaders, and bulldozers. In all cases the economic feasibility of mining thin seams depends on the market needs, the market location, the equipment used, the mine management, the quality of the coal, and the labor market. Slight negative combinations of these parameters have closed many mines while positive combinations allow others to exist. The limited mobility or slow movement of large stripping shovels, draglines, and bucket wheel excavators make them more economically fitted to areas where large quantities of overburden are to be moved. This is necessary to keep the transfer and setup time between pits a negligibly small percent of the total operational time. Equipment such as the scrapers, loaders, backhoes, trucks, and bulldozers that are either very mobile or can be trailered is more versatile and can be used in the smaller area mines.* Mobile equipment is also more practical in areas with shallow overburden because of the constant movement required while removing overburden. In thin coal seams the equipment is usually paired such that the operational equipment can be listed as: (1) dragline-loader, (2) shovel-truck- loader, (3) scraper-loader. (4) loader-truck-loader, or (5) loader-loader. In these operations the overburden is removed with the first machine(s) of the pairing and the loader or loaders are used for coal production. Recent articles in Coal Age (Chironis, 1978) and Mining Engineering (Wiebmer, 1978) have discussed varying philosophies in mining similar seams of coal. One operator uses draglines for competitive mining while the other uses scrapers for the same purpose. Both cite strong cases sup- porting their choice of equipment as good sound economic decisions and their success supports their choices. The drag-line operation is adding new larger draglines to decrease the cost of mining, rather than to increase coal production. The scraper operation has also gone to more and larger scrapers for basically the same reasons. These operations and all

Jan 1, 1981

By Nguyen V. V

The development of structural defects in the overburden material immediately behind a production blast was studied using surface and subsurface techniques. A significant increase in vertical and horizontal fracture intensity was recorded. The extent of fracturing into the highwall appeared to be dependent on the structural and petrologic characteristics of the various lithological units and the relative position of the explosive charges. A shallow zone of disruption to a depth of 10 m and extending to around 30 m from the newly formed highwall crest was recorded. Horizontal fractures in lower units of the overburden sequence were recorded at distances up to 50 m from the new highwall Face.

Jan 1, 1981

By William L. Husk

Stockpiles have always been a necessary part of coal mining except, perhaps, when a person was mining only for the needs of his family from a seam on his home place or coal mined for the use of a small hamlet and carried to each man's house as it was mined. Then it may have been stockpiled at each man's place for several days or on the village common. Mining with this limited production required waste stockpiling. Stockpiling of the products of coal mining, both coal and waste material, has always been a necessity. Very little coal has ever been moved directly or immediately from the working face to the point of consumption and burned. It has always been expedient to stockpile the coal some- where and store the waste.

Jan 1, 1981

In recent years stricter requirements imposed variously by the Companies Acts, auditors and the Stock Exchanges have resulted in annual financial statements of mining companies becoming more detailed, informative and useful. Standards of reporting on ore reserves have not kept pace with the improvements in financial information disclosure, despite the fact that ore reserves are usually the most important asset of a mining company. The ore reserve reporting practices of fifteen leading Australian mining companies are analysed against important specific criteria. In terms of detailed and meaningful disclosure, there is scope for major improve- ments in annual ore reserve reporting Practices.

Jan 1, 1981

By Martin Hertzberg

The concept of limit burning velocities is being used to formulate a quantitative theory of flammability limits. Competing and complicating processes dissipate power from a combustion wave and quench propagation at some characteristically low limit velocity. Two earlier reports dealt with process (a), natural convection (RI 8127); and with process (b), conductive-convective wall losses (RI 8469). This report considers process (c), radiative losses, and process (d), selective diffusional demixing. The limit burning velocity for radiative losses is [(SU)c ~ e cp] It is normally not a significant process for premixed gas flames; however, for laminar flame propagation in a gravity-free environment, it is the only loss process present. Accordingly, limit velocities at zero gravity should be much lower than on earth, and premixed gases should be flammable over wider composition ranges. For highly emissive dusts, soot, or ash-forming flames, radiative losses are significant even under normal gravity conditions. Selective diffusional demixing is a complication that manifests itself in the form of cellular flame structures and wide gaps in composition between upward and downward propagation limits. It induces a burning velocity shift (?Su)d, causing the flame to behave as though it were richer or leaner than its initial composition, depending on whether the fuel or the oxidizer mole¬cule has the higher diffusivity. A simple pertubation analysis shows that the process generates stable cellular flames whenever [dsu] > 0, where ci is the concentration of the reactant with the higher diffusivity. The same analysis indicates that at the opposite stoichiometry, where [dcu] < 0, laminar structures are stabilized. A simple formula for the diameter of cellular flames is derived, which predicts that dcell should vary inversely with the product of the diffusivity difference Di -DJ, and the burning velocity slope [dc ]. Those predictions are in good agreement with the available data. Buoyancy forces for upward propagation induce flame front curvature, and hence buoyancy and selective diffusion are mutually supportive in upward propagation. Thus large gaps in composition between upward and downward limits are present in those composition domains where cellular flames are stable.

Jan 1, 1981

By Robin J. Hickson

The Ortiz Mine is operated by Gold Fields Mining Corporation, a subsidiary of Consolidated Gold Fields Ltd., one of the world&apos;s major gold producers. The Ortiz Mine is Gold Fields only heap leaching facility as well as being their first operating mine in the U.S.A. The hydrometallurgical processes utilized for recovery of gold and silver at Ortiz are discussed along with the several practical changes in operation adopted since start-up. Included are heap leaching by cyanidation, concentration of values on activated carbon, desorption, and the final electrowinning steps prior to shipment. Construction costs and pertinent technical data are shown.

Jan 1, 1981

By D. A. Stanley

The Bureau of Mines conducted laboratory-scale experiments to determine whether or not surface waters with a high organic content could be purified sufficiently to be used to replace the natural high-quality deep well water currently being used in the silica flotation step of phosphate rock beneficiation. Waters abundant in organic matter were collected from two central Florida streams, flocculated with a cationic polyethylenimine polymer, and processed in a sand filter. This treatment removed most of the organic materials from the water. Untreated surface water, treated surface water, and distilled water were used to compare the flotation response of the acid insolubles in an amine flotation circuit. Surface water treated with PEI-1000 was shown to be as effective as distilled water for the acid-insoluble-flotation step. Flocculation and filtration can therefore produce water suitable for amine flotation of quartz, which would permit substitution of surface water for deep well water.

Jan 1, 1981

By R. Klimpel

Recent work has shown that the measurement of flotation kinetics in the laboratory is useful in providing guidelines on how operating sulfide flotation plant performance can be improved. This work outlines the influence of various factors on flotation kinetics such as collector/frother type and concentration, particle size, and frother blending.

Jan 1, 1981

By A. Erickson

The effectiveness of a loader-mounted fan on diesel vehicles combined with natural convection for ventilation of a dead heading (the patented Janelid system) was investigated experimentally. The results were obtained using CO2 as a tracer gas in a 1/4 scale model heading. Buoyant forces were scaled to establish similarity with full scale. For a loader moving in a typical load-haul-dump cycle, the loader-mounted fan reduced the tracer gas concentration by 26 percent compared with a reduction of 32 percent for a jet fan of four times the flow capacity.

Jan 1, 1981

By John F. Brass

INTRODUCTION The Jim Walter Corporation is a Florida based organization with diverse interests. They have operations in many states and overseas, but the heart of the company is in the southeast. The major part of the corporation&apos;s business is home building and everything that is related to it. In 1969, the Jim Walter Corporation gained an interest in coal mining through the acquisition of the U. S. Pipe & Foundry Company which had two slope mines to supply its requirement of metallurgical coal. In the early 1970&apos;s it was decided to enlarge the coal mining activities and work was started on the Blue Creek project. This involved sinking four new deep mines (originally there were to have been five but it was later decided that the property could be satisfactorily worked by four mines). They are all located in west central Alabama between Tuscaloosa and Birmingham. They have a combined projected output of 7314 million tons of very high grade metallurgical coal per year to be reached by the mid 1980&apos;s. These new mines are all to work the Blue Creek seam which is a very gassy seam and in the area to be mined is found at between 45m (1500 ft.) and 731m (2400 ft.) below the surface. Longwall is the only practicable method of mining to produce the planned outputs in the conditions prevailing and each mine is planned to have three longwalls as the primary production system. Continuous miners will be used just to do the development work for the longwalls. No. 3 Mine is the most advanced of the mines and started the first longwall early in 1979. The second unit started in the middle of 1980 and the third is scheduled for mid 1981. The first longwall at No. 4 Mine is expected to commence production early in 1982. This paper attempts to relate some of the problems that have been encountered and the lessons that have been learned.

Jan 1, 1981

By Wolfram Schnabel

Recently Lurgi has succesfully commissioned Peru&apos;s first direct reduction rotary kiln at SIDERPERU?s Chimbote works. The order included comprehensive engineering services and supply of special equipment to modify three existing cement kilns according to the SL/RN process. The kilns were cut to 62m length and installed with a slope of 2.5%. A new heating system, including shell burners, was supplied and inlet and outlet ends of the kilns completely renewed. Figure 1 shows the kilns after modification.

Jan 1, 1981

By J. D. Miller, P. J. McDonough, H. Q. Portillo

Previous investigations have demonstrated the catalytic effect of silver additions in the ferric sulfate leaching of chalcopyrite [ ] The enhanced rate of leaching was found to be due to the formation of an intermediate Ag S film which forms on the Cures2 surface by an exchange reaction Under these conditions, unlike the uncatalysed ferric sulfate leach, the elemental sulfur forms a nonprotective reaction product on the Ag S crystallites As a result, the rate appears to become limited by an intermediate electrochemical reaction in {he Ag2S film rather than by transport through the elemental sulfur reaction product [ ] The reaction rate was found to have a complex dependence on the Ag+, Fe++ and Fe+3 concentrations, but independent of the Cu concentration Electrochemical measurements with a Ag,S-coated chalcopyrite electrode provide further information regarding the nature of the reaction mechanism The kinetics of the rate limiting, intermediate electrochemical reaction are analyzed in terms of the Butler-Volmer equation

Jan 1, 1981

By David E. Morse

Burundi, a small central African republic located between Tanzania and Zaire, remained essentially a nation of small family farms in 1978-79 with approximately 95% of the population engaged in subsistance agriculture. Coffee and tea continued as the nation&apos;s major export commodities. Mineral exports, small tonnages of cassiterite, wolframite and bastnasite, accounted for an estimated 3% of total exports in 1978 and 2% in 1979, or $2 million2 in both years. Burundi&apos;s major mineral imports in 1978-79 were cement, iron and steel, and refined petroleum products. Abnormal weather conditions, a drop in world coffee prices in 1978, and the conflict in neighboring Tanzania and Uganda in late 1978 and early 1979 combined to re-strict economic growth in Burundi during 1978-79. The gross domestic product (GDP) posted a gain of 6.7% in real terms for 1978 and an estimated 2.5% for 1979 which was significantly less than the 13.7% recorded in 1977, a time of high world coffee prices. The manufacturing and construction sectors were hard hit in 1979 by the conflict between Burundi&apos;s eastern neighbors because of transport disruptions which made building materials and manufacturing inputs almost unobtainable.

Jan 1, 1981

By W. J. Aitken

The pneumatic conveying of relatively large abrasive materials by dilute-phase conveying techniques has been applied in the underground mining industry for many years especially for backfilling mines and the hoisting of ore, coal, or rock out of the mines. The technique was extensively used in Europe, especially Germany and Britain for backfilling coal mines with rejects from the coal cleaning plants which not only helped to reduce environmental problems on the surface, but offered support to the overlaying strata in the deep underground mines, Similar techniques are being employed in the U.S.A. especially in uranium mines for the disposal of tailings, the main purpose being to extract a larger percentage of the ore from the pillars especially under weak roof conditions. Other than for the backfilling of abandoned mine entries, pneumatic conveying has not been applied in the mining industry in surface applications. In this paper, some consideration is given to three applications for open pit mining which may prove beneficial, namely hoisting coal up the high wall, sealing off auger holes, and stabilizing the high wall when being undercut by a longwall system.

Jan 1, 1981