Search Documents

By Tim F. Dyson

Feasibility of employing automated processing and detection techniques in the mine disaster communications problem is demonstrated. Efficient processing methods are developed. These methods have been demonstrated both in a laboratory and in a field environment. Evalua¬tion of existing computer capacity is given along with recommendations for expansion.

Jan 1, 1981

By Thomson I. R R, Friday R. G, Palmer W. T

The paper introduces the problems encountered in designing open stopes and briefly examines the factors that determine the final stope dimensions achieved after mining is completed. A case study is presented where monitoring of a stope was considered necessary due to the expected formation of a highly stressed crown pillar above the stope. The influence, on the mining approach adopted, of a yielding crown pillar is discussed. Monitoring and numerical modelling were used to develop an understanding of the behaviour of the particular stope as mining progressed. A comparison between the measured displacements and the numerical predictions at an interim stage of mining was carried out to assist in choosing the final sequences involved in completing the stope.

Jan 1, 1981

By Earl L. Phillips

The Bureau of Mines conducted laboratory tests on samples of pozzolanic-cement concrete to develop a low-strength backfill. Results show that support costs can be lowered by replacing a portion of the portland cement in mine backfill with pozzolan (fly ash) and lime. Unconfined compression tests on various ratios of fly ash to cement in 84 samples produced compressive-strength curves that can be used to estimate the best backfill mix for any mine.

Jan 1, 1981

By A. H. Underwood, M. –Ls. Trépanier

INTRODUCTION The King and Beaver mines of Asbestos Corporation Limited (ACL) were joined in 1957 to form the King-Beaver mine. In 1964, ACL purchased the Johnson's Asbestos Company. The combined underground workings are a part of the King- Beaver mine. Asbestos ore is mined at the rate of 4080 metric tons per day (mtpd) to provide 15% of the company's daily requirement in the Thetford Mines area. Figure 1 shows the location of Thetford Mines. Two shafts service the underground. No. 3 shaft, 457 m deep, is used for personnel and material transportation, downcast ventilation, and ore hoisting. No. 4 shaft, 820 m to the south, is 389 m deep. It is used for material transportation and upcast ventilation. Figure 2 shows the relative locations of the shafts and the underground workings. The ore is mined by block caving. HISTORY The orebody outcropped at surface and was first mined as an open pit. Underground mining commenced when open pit mining became impractical. Shrinkage stoping, used initially, was unsatisfactory in the highly fractured ore. Sublevel stoping improved ore recovery and safety, but did not overcome the adverse effects of the un- stable rock. Observations of the rock failures indicated that block caving would be satisfactory. This was confirmed by careful investigation and testing. A method of block caving similar to that used at the Miami Copper Company was adopted. The first block commenced production in June 1933. BLOCK CAVING General A large block of ore is undercut above pre- pared drawpoints. The ore above the undercut caves by its own weight. Caving progresses up- ward as the caved ore is drawn. A large proportion of the rock breaks up in the caving action so that it will pass through the drawpoints. Oversize blocks are broken by drilling and blasting or mudcapping. Figure 3 shows the progressive stages of block caving. In the central part of the ore zone, the vertical dimension of a block is determined by the 132 metres between production levels. When isolated ore pockets are developed, the vertical dimensions of a block depend on the extension of the ore zone above the undercut. The minimum horizontal dimension of an under- cut determines the cavability of the overlying block. When necessary, caving is assisted by drilling long horizontal holes into the block above the undercut and blasting them. This procedure speeds up or restarts caving. It will not ensure complete caving of blocks having undercuts less than 30 m wide. Orebodies suitable for block caving are highly fractured and wide enough to cave freely without excessive dilution. Undercutting must

Jan 1, 1981

By Velu Annamalai

In-situ uranium solution mining involves the injection of a lixiviant (leach solution) through appropriately placed wells into the underground ore zone. Upon contacting the uranium minerals, this solution will dissolve the uranium. The uranium containing solution is then pumped out of the wells into a processing plant where the uranium values are removed, typically in ion exchange columns, and the stripped liquor is recycled back into the field. The lixiviants may be acidic or basic. Where the ore zone mineralization contains appreciable carbonate, as in the South Texas fields, acid consumption would be excessive and the typical solution is ammonium carbonate bicarbonate at about 5-10 g/l and a pH of 7-9. Because the usual uranium minerals, uraninite or coffinite, contain uranium in the insoluble tetravalent state, it is necessary to add an oxidant to increase the valence to the hexavalent state where the uranium is soluble. Oxygen dissolved in the lixiviant has been shown to be quite effective for this purpose. It is also much more economical than other oxidants. Of concern is the possibility that (1) its solubility may or may not provide concentration levels adequate to give an economically attractive uranium level in the extracted liquor, and (2) the addition of oxygen in excess of the saturation level so as to increase the uranium grade in the lixiviant may cause gas blockage of the typical fine-pored ore formations.

Jan 1, 1981

By Alan M. Muir Wood, Gerhard Sauer

There axe two essential features of administrative practices in tunnelling in order to provide proper encouragement to innovative and economic tunnelling: first, that there should be a continuity in the decision making at all stages so that the full implications of decisions in early stages of planning and design are understood; second, that there should be appropriate provision for variation so that the greatest possible benefit can be derived from modifying the working scheme in relation to the characteristics of the ground and from study of its behaviour during execution of the work. Examples are given from the Authors[?] experience as to the benefits to be derived from the application of such principles.

Jan 1, 1981

By Larry Sevenker

On the basis of favorable salt characteristics, primarily compressive strength and impermeability, solution-mined cavities can provide structurally stable isolation chambers for waste. Solution mining techniques are established for storage of hydrocarbons. The proposition of waste isolation in engineered salt cavities is similar to this practice relative to characterization, certification and safeguards. What materials are isolated and how operations are conducted are principle differences. Compatibility of wastes with other wastes must be considered, but hazards can be precluded by avoiding certain mixtures. Waste material characteristics and cavity considerations are discussed.

Jan 1, 1981

By Barry H. G. Brady

A state of stable equilibrium is required in a mine structure to ensure that small increases in the mined void are accompanied by only small displacements of the rock mass. Methods of determining the stability of equilibrium in a rock mass currently require a geometrically regular stoping layout, and introduce a number of simplifying assumptions. The method reported in this paper models the mine near-field using Finite Elements, and the far-field using Boundary Elements. The stability of equilibrium in the modelled structure can be assessed directly from the value of selected principal minors of the global stiffness matrix.

Jan 1, 1981

By K. K. Kohli, S. S. Peng, R. E. Thill

Introduction Since the adoption of the Surface Mining Reclamation and Control Act of 1977, which mandates that surface subsidence be an intergral part of the underground coal mine design, there has been a sudden rise of demand on guidelines for minimizing surface subsidence and its associated structural damages. Unfortunately there is no sufficient amount of systematic subsidence data to fill such a gap, although considerable research has been devoted to the subsidence induced damages of surface structures in the past. However, it was said that many surface subsidence surveys have been performed and monitored by coal companies during the past twenty years, and that it will be a great source of information for subsidence engineering design if they can be collected and assembled together. An effort was therefore initiated in the Department of Mining Engineering, West Virginia University, under contract with the U. S. Bureau of Mines in December 1978 to contact each individual coal company in the Northern Appalachian Coal Field for any surface subsidence survey data. After 10 months' survey, the data collected include: 17 longwall panels and 2 room and pillar sections. The data in each panel and section cover the complete set of subsidence survey raw data, underground mine layout maps, surface topo maps, geological loggings showing the stratigraphic sequences and thickness of the overburden, and if available, locations and types of surface structures. On-site visits were followed to study the surface terraines and structures. Interviews were conducted with the owners of the surface structures in most cases about, if any, the history and characteristics of damages. Most subsidence surveys started with the first panel and ended with the second or sometimes, but rarely, the third panel. The first panel may be located in a virgin area but frequently it was adjacent to (on the tailentry side) a mined-out room and pillar section. It must be noted that all of the subsidence data is restricted only to the amount of vertical subsidence and that the horizontal displacement measurement was completely ignored. Primarily due to the fact that vertical subsidence is the most striking feature in a subsidence trough, which is mistakenly considered to be the only critical contributor to surface structural damages, and that a horizontal displacement survey is much more complicated and time-consuming.

Jan 1, 1981

By Henry Chajet

Good morning, it is truly an honor to have been invited to speak before you today Before I begin my update on MSHA's activities, I?d Like t o quickly say a few words about the American mining congress and its mission in Washington, AMC is a national trade association representing most of the producers of the nation's metals, nonmetals and coal, we also represent the manufacturers of mining equipment and supplies and the financial and consulting institutions which service the mining industry. It is the diversity of our representation which gives us our greatest strength in our petitioning efforts, the administration and the members of congress know that an AMC position is the result of the careful consideration of a vastly diverse group of mining concerns. Our president, Al Overton, perhaps has the best description of AMC when he speaks of us as "the mining industry's eyes and ears and its collective voice in Washington."

Jan 1, 1981

By Kenneth P. Katen

Though the use of continuous mining machines consolidated the operations of cutting, drilling, blasting, and loading in one machine that would theoretically provide uninterrupted production, it was soon realized that the face haulage and roof support operations remained as major impediments to continuous production. The ability to provide not only continuous cutting and loading, but also continuous haulage and roof support (see Fig. I), was the basis for the introduction of mechanized longwall systems in this country from Europe in 1951. The early systems employed friction props for roof support, but were to become obsolete shortly after introduction of the first hydraulically powered, self-advancing supports in 1960. Since then, use of the longwall technique has grown to the point where it is currently providing more than 5% of the annual output of underground coal mines in the United States. The shortwall system had its origin in Australia, but was first introduced into this country in 1962 following the development of powered roof supports. It, too, provides for continuous cutting, loading, and roof support (see Fig. 2), but has not experienced the widespread popularity of longwall due to its inherent inability to easily provide for continuous haulage. While there are in the neighborhood of 100 longwall systems currently in operation in this country, there are only a handful of short- wall operations providing production of slightly more than 907 184.7 t/a (1,000,000 stpy) Both of these systems provide uninterrupted roof support for face operations by means of hydraulically powered steel roof supports. In each case, the coal removal consists of open-end cuts made from the narrow end of a large rectangular pillar (panel) which has been blocked out by continuous miners developing entries around its perimeter. However, this is the extent of the similarities between the two systems. It is hoped [ ] that the information presented in this chapter will enable the reader to better understand the two mechanical systems and the mining concepts involved in their employment.

Jan 1, 1981

By T. S. Mohibatsela, R. V. Ramani, C. V. Manula

The Mineral Engineering Department of The Pennsylvania State University has developed a suite of computer models for anthracite open pit mining (Fig. 1)1 Individual sub-systems have been developed to (a) interpolate geologic field data to obtain coal tonnages, waste volumes, and strip ratios; (b) simulate equipment performance on selected pit profiles to generate data required to choose coal and waste removal equipment; and (c) evaluate selected cost factors to determine either a rate of return for a specified selling price or vice-versa. This paper describes the application of two of these subsystems, namely, the Reserves Model (GEOL) and the Open Pit Materials Handling Simulator (OPMHS), and how these may be applied for the selection of equipment for a prime anthracite mining site.2

Jan 1, 1981

Reduce the number of accidents caused by slips and falls from large mining equipment. Approach A powered lift was developed that provides operators with a safer way of getting on and off large machines. How It Works The powered step is designed to lift personnel and materials to working levels on large machines. It eliminates hazardous blind steps and makes it unnecessary to climb on irregular surfaces made slippery by mud, ice, snow, and accumulations of grease. The step is powered by a self-contained electric/hydraulic unit which is connected to a vehicle's auxiliary power supply. When in the "down" position, the step rests about 15 inches above ground level. When the power unit is activated with an electrical switch located on the step, a Single cylinder attached between two lifting arms smoothly lifts the step. In conjunction with the lifting motion, a linkage and bearing arrangement on the mounting end of the lift arms causes the step to rotate towards the machine, so that the step moves in an arc from ground to platform level. When the machine Is operating, the step is automatically locked in the "up" position, protecting it against any damaging contact with obstructions. The step is lowered by activating a pressure release solenoid. An in-line orifice controls downward speed and prevents free fall. On most machines, additional control switches are conveniently located at ground level and in the operator's cab. Visual alarms and machine interlocks are provided where necessary to prevent machine operation when the step is In the "down" position. The powered step can be easily adapted to any type or model of large machinery.

Jan 1, 1981

By Thomas P. Dowling

With the increased usage of AN/FO type blasting agents and the introduction and development of non cap sensitive slurries, water gels and other types of blasting agents, proper initiation and boostering of these insensitive materials has become a most important aspect of every blasting operation.

Jan 1, 1981

By M. Measures, W. A. Napier, C. Pomroy, J. M. Jardine

INTRODUCTION In most uranium mines the concentration of uranium in the ore is low enough that inhalation of dust does not present a radiological problem. Conversely in the mills there is a potential inhalation hazard from inhaled uranium in concentrated form, namely "yellowcake" and other compounds intermediate between the ore and the final product of the mill. It was generally assumed that the solubility of yellowcake placed it in the category of Class D materials. This plus the fact that the uranium is non-enriched led health physicists to assume that the potential health hazards were a result of the uranium's chemical properties rather than its radiological properties. Bioassay programs have thus been limited to routine urine sampling at a weekly or monthly frequency. In most cases when a high reading was obtained, subsequent sampling within one or two days showed a rapid return to low levels, therefore tending to confirm the class D nature of the material. Two developments over the last few years have however suggested that modifications to this simple bioassay program may be necessary and practical. Firstly, a number of studies on the solubility of uranium mill products, from ore to yellow cake, in simulated lung fluid (Eidson A.F., Mewhinney J.A., 1980) have shown that some of the material is not class D, but class W or even Y. This raised the possibility that, while the urine levels rapidly decreased, indicating rapid excretion of the class D component, the W and Y components remained in the lung. Thus an unsuspected lung burden could have been accumulated. The second development, the ready availability of [in vivo] counting facilities with which to make direct measurements of uranium lung burdens, offered a means of confirming the hypothesis of unsuspected lung burdens. A study was therefore initiated to correlate lung burdens with urinary excretion. METHOD A total of 79 subjects from 3 uranium mills participated in the study. They were brought to the Ottawa laboratories of the Radiation Protection Bureau in groups of 4 or 6, over a period of several months. In Ottawa, [in vivo] thorax measurements were performed, and a urine sample collected. Each subject also brought with him a urine sample that had been collected the previous day. All samples were split, for analysis by both R.P.B. and the mill laboratory. [Concentrations of Uranium Dust] Results obtained by mills A, B and C for concentrations of uranium in air at various locations are given in table 1. Samples taken at mill B were obtained using continuous sampling with a midget impinger over a six hour period. Samples taken at mills A and C were 5-minute gravimetric samples. [Subject Selection] The subjects were selected to represent a wide range of work history in terms of both length of employment and type and location of job, as shown in table 2.

Jan 1, 1981

By Dennis H. Laubscher

INTRODUCTION The selection of mass mining methods is the situation facing not only planners of new operations, but also those involved with cur- rent operations, including the eventual change from open-pit to underground. Increasing ground control problems on many mines, plus a better understanding of dilution and ore loss problems have meant a review of current mining methods and support techniques. Experiments are only successful if conducted in the right mining environment and on the right scale. Mining personnel have been known for their conservatism and will tend to persevere with an established method rather than change; often, hidden costs will obscure the correct economic assessment. An established mining sequence is not necessarily correct in the long term. However, recommendations to change are usually met with opposition because of inconvenience, temporary production problems and the desire for a trouble-free guarantee. In any planning exercise, care must be taken that time and money are not wasted in trying to achieve the unattainable. During the decision-making period, production personnel must be involved, and, if possible, they should visit similar omrations to that proposed. Co-operative production personnel will help ensure success. Descriptions of mining methods are available in technical papers and books, and it is not intended to discuss this aspect, but, rather, the various factors which must be recognised before arriving at a final selection. In another paper presented at this Conference (Heslop and Laubscher, 1981) factors affecting ore recovery and dilution are discussed in greater detail for various cave mining methods. PRELIMINARY CONSIDERATIONS Comprehensive Geological Data. Geological information is available during the exploration stage, but, often, core from exploration drilling is not analysed with the selection of a mining method in mind. Drilling costs are high, therefore the maximum benefits must be derived from this operation. Holes which have not intersected ore may provide data on possible shaft sites, and 35 mm colour slides of core, sound logging and geomechanics classification, will provide a record which can be used with confidence at a later date. Intersections of the various rock types should be kept for future study; for example, is weathering likely to be a problem, bearing in mind that this can be accelerated in the warm, humid atmosphere of an underground mine. The accumulation of data required to select a mining method starts with initial geological work in the target area, whether this be surface mapping or a diamond drill hole. Publications. As technical papers, reports and books are used in the selection of mining methods, an appeal is made to authors to describe the geological environment so that readers can relate to their own conditions. Not enough emphasis is given to the problems experienced and the techniques employed to overcome them. Follow-up papers are seldom written and we should be prepared to discuss our failures. Diagrams are often misleading, as the ideal and not actual situations are depicted. The caved ore/waste interface is not a straight line, and whereas this may not be significant in a diagram of a 200-117 draw height, it certainly is in sub-level caving with draw zones only 1 - 2 m width but up to 20 m high. SUMMARY OF FACTORS AFFECTING THE SELECTION OF UNDERGROUND MASS MINING METHODS (a) Regional rock stresses and mining geometry. (b) The geomechanics rock mass classification of the orebody and surrounding rock mass. (c) Ratio of the surface area of the ore/unpay interface to the contained ore which determines ore losses and dilution. (d) The cavability and fragmentation data of the ore and hangingwall. (e) The mineral distribution in the orebody and its dilution zone.

Jan 1, 1981

By Manuel Diaz del Rio

At the present time there are over 5,000 Kms of railway tunnels in existence throughout the world. In many cases these tunnels were built over a century ago using techniques obsolete today. Supervision and maintenance of these tunnels is essential to the economy of each country involved. For this purpose an electro-optical measuring system has been designed incorporating highly complex soft and hardware (15 mW laser, high resolution TV camera and processing computer), mounted on a vehicle. Its job is to scan, record and compare sectional gauge values (profiles) and strains inside tunnels both momentarily in situ and on permanent record, as an aid to the supervision work. From the state of the strains observed, in conjunction with an infrared spectrum of the tunnel lining and soil involved, the mechanical stresses in the tunnel can be deduced by applying the boundary elements method.

Jan 1, 1981

By V. Voller

A relatively simple model of grinding which incorporates both the Bond grindability equations and the population balance equations has been extended to form a comprehensive simulation package that can describe most kinds of conventional grinding circuits. The package has two programs, with the first consisting of an input program which helps the user to specify the prescribed circuit, while the second program performs the actual simulation. The package serves two main purposes - i) as a check on mill design, with the output providing not only predictions for the product passing size but also of the full product size distribution, and ii) as a means to assess the likely effects on the product size distribution of operating under different sets of conditions.

Jan 1, 1981

By G. Y. Nisbet

The contribution made to the economy of South Africa by the-minerals industry is discussed according to four of its aspects. Firstly, the industry supports both students and lecturers in technical and academic institutions. This support covers virtually the whole range of courses available at the universities and technikons, although most is obviously devoted to the engineering and science faculties. Secondly, the industry makes a direct financial contribution to the State in that it contributes about40 per cent of the State's receipts from direct tax paid on incomes and 30 per cent of the contributions to the total State revenue. It provides employment for 28 per cent of the total active labour force, and contributes 24 per cent directly to the gross domestic product. Thirdly, the industry is responsible for over 65 per cent of the country's foreign earnings in spite of the significant rise in exports from the manufacturing sector. South African minerals are of crucial importance to the word, since the country has the world's largest reserves of seven minerals and features very prominently in many others. Finally, the industry makes an indirect contribution, referred to as the multiplier effect. This is the ripple effect on the economy made by a large injection of momey by which that money acquires an added effective value. A study made of the total production of the mining industry in 1978, for instance, showed this multiplier to havea value of 1,5. Thus, if this effect is included, the industry's contribution to the gross domestic product is 44,S per cent. Similarly, the industry is responsible for the creation of jobs both within itself and in other industries, which could amount to 100000 for the period 1981 to 1935.

Jan 1, 1981

By Kenneth Maser, Douglas W. Ounanian, Joseph S. Boyce

Foster-Miller Associates, Inc. (FMA), under contract to the Department of Transportation (DOT) and the Urban Mass Transit Administration (UMTA), is currently developing an Extruded Tunnel Lining System (ETLS). The ETLS would reduce ground support costs in machine bored tunneling by eliminating the need for temporary support, and by slip-forming the final concrete lining directly behind the Tunnel Boring Machine (TBM). The system can advance at variable rates, from 0.6 to 3.7 m (2 to 12 ft) per hr, by combining three systems: a very high early strength concrete, continuously produced and delivered by a concrete process system; a slipform/bulkhead system for supporting the concrete prior to strength gain and exposure; and a control system for form/bulkhead alignment and concrete process control. Large-scale tests are planned to demonstrate the system in a 3 m (10-ft) diameter steel "tunnel".

Jan 1, 1981