Search Documents

By R. F. Holub, E. Franco, T. B. Borak, K. J. Schiager

INTRODUCTION According to a recent analysis by Schiager et al.(1981), inhalation of radon daughters continues to contribute the largest risk from exposure to radioactive materials in underground uranium mines. The American National Standards Institute (1973) has published a concensus standard for radiation protection in uranium mines. According to this standard, a monitoring system for radon daughters must be capable of measuring the annual accumulated exposure in working level months within an uncertainty interval of 50% at the 95% confidence level. To satisfy this criterion, uranium mining companies in the USA have adopted a procedure consisting of single or periodic measurements of the air concentration of radon daughters. All of the measurement methods sample a known volume of air through a filter. After a specified delay interval, the filter is analyzed for radioactivity. The exposure rate from total airborne potential alpha energy in units of working level (WL) is estimated from the measured activity on the filter. For control purposes, this measurement establishes whether or not a work area is safe for occupancy by miners. For routine dosimetry, the concentration estimated from the grab sample is assigned to the appropriate work area. It is then assumed that the concentration of radon progeny is equal to the average of the two measurements at the beginning and end of the specified interval. Meanwhile, the work locations and exposure times of each miner are recorded on the daily time card and verified by the shift supervisor. Most cards provide space for 15-minute time intervals. The exposure in working-level hours (WL-hr) for each shift is obtained by summing the time spent in a given location multiplied by the exposure rate (WL) assigned to that location.The exposure of an individual miner to radon progeny is summarized on a weekly basis and commonly reviewed each month. These values are then accumulated in units of working level- months (WLM) during the calendar year. EVALUATION TECHNIQUE AND RESULTS The evaluation of grab sampling methods for monitoring exposure to radon progeny is presented in two sections. The first section examines each method individually according to accuracy, precision, and uncertainties attributed to human errors. The second section includes an analysis of procedures which are common to all measurement methods. The ultimate goal is to determine whether a specific measurement method, or grab sampling in general, can fulfill the criterion that the annual accumulated exposure of each miner be known to within ± 50% at the 95% confidence level. In addition it is essential that the above criterion be satisfied at an acceptable cost to the mining company. The results of each testing procedure are presented in terms of the contribution of the relative uncertainty in the estimates of cumulative WLM. Each of these are then combined to form a figure of merit for the complete monitoring system. The method of combining statistical uncertainties and interpretation of the results is subject to some debate. However, since all of the tested parameters enter into the final computation of WLM multiplicatively, we have used the commonly accepted procedure of combining the squares of the relative uncertainties. We have also assumed that each of the uncertainties is derived from independent random variables and the covariance of any two variables is zero. A description of each grab sampling measuring method is given in Table 1. Also included is the equation used to compute WL from the measured quantities. Accuracy (U A) Our definition of accuracy is based on the uncertainty inherent in any method which attempts to estimate potential alpha energy without unambiguously determining the concentration of the three unknown radioisotopes, RaA, RaB and RaC. (For simplicity, the RaC and RaC' nuclides are referred to in combination as RaC.) The inherent uncertainty strongly depends on the mixture of these three components at the time of measurement.

Jan 1, 1981

By J. L. Hendrix, R. B. Dix

A study was made of the United States Bureau of Mines chlorine-oxygen leaching process for complex sulfide concentrates. The investigation sought to determine the kinetic order and mechanisms involved in the reactions between galena and sphalerite with chlorine. The influence of copper on the extraction rates was also studied. It has been shown that the rates of reaction of chlorine in aqueous solutions with sphalerite and galena are both zero order at 373 K with rate limiting step being the chemical reaction. Addition of cupric chloride increased the extractions of both lead and zinc.

Jan 1, 1981

By Dennis S. Kostick

Soda ash is produced in over 39 countries by the Solvay ammonia-soda process or by mining natural sodium carbonate deposits. The total production of soda ash in 1980 is estimated at slightly over 29 million metric tons. Synthetic production accounted for over 75% of this amount with the balance of production originating from natural sources (either trona or sodium carbonate-rich brines) found primarily in the United States, Mexico, Kenya, and Chad.

Jan 1, 1981

By Don B. Shupe, John K. Berry

The handling and disposal of mine water is a much larger problem than is apparent at first glance. Many more tons of water are removed from underground coal mines in the United States each year than tons of coal. In the old anthracite region of Pennsylvania the average was around 32.7 t (36 st) of water for each ton of coal produced, while bituminous mines average about 4.5 or 5.4 t (5 or 6 st). Water encountered in the mines may come from several different sources. In mines with light cover and without a firm solid roof, rain may seep directly into the workings. This is also true of deeper mines where pillar falls have broken the roof to the surface. The top under creek beds is generally faulty and broken and water comes through the roof at this point. Deeper mines are frequently overlain by water-bearing strata and pillar breaks and faulty top can admit water, while places running to the dip often accumulate water which comes up through the bottom. In all cases, except where passing under a year-round stream, the amount of water made is usually pretty closely connected with the weather-more water during the rainy season, less in the dry, although the deeper a nine is, the longer it is before changes in rainfall are felt. Another source of water, not connected with seasonal changes, is old water, accumulated over a period of time in abandoned workings of the mine, or from flooded adjacent mines. Here the water filters through the coal, the parting, or comes up through cracks in the bottom. Similarly, core holes, drilled to prospect the property, can be a source of unexpected water and modern safety requirements for dust-allaying water at the working faces can turn a pleasant working area into a soggy mess over the weekend if the system is not properly maintained and operated. Why water must be disposed of is obvious. If allowed to accumulate, sooner or later the mine will fill up, or at least it will become "roofed" in low places, blocking ventilation and traffic. It must be controlled long before it reaches this stage. Water standing in the working faces is

Jan 1, 1981

By M. Karmis

For several centuries surface subsidence has been recognized as an inevitable consequence of most underground mining. In fact, British court records of disputes and litigations related to property damage due to mining subsidence can be traced to the early fifteenth century (Shadbolt, 1978). The first systematic investigations of the mechanisms involved in mining subsidence can be credited to Belgian Mining Engineers. The re- search effort was initiated after the widespread movements and the resulting structural damages suffered by the City of Liege in the 1920's. The publication of Gonot's 1871 treatise "Loie de la NomZ" (normal theory) was one of the most not- able achievements of the Belgian school of that era (Gonot, 1871). During the past 100 years the phenomenon of mining subsidence has been the subject of intensive research, particularly in Europe where long- wall is the most common method of underground coal mining. Many theories have been advanced to explain the mechanism of ground movement as it develops from the excavation, through the superincumbent strata, to the surface. Such theories include the original concepts of beams, arches, domes and the contemporary mathematical modeling principles of strata movement assuming two extreme concepts-- a continuous elastic medium and a stochastic medium for the superincumbent strata. An excellent review of the development of these theories ?-s given by Shadbolt (Shadbolt, 1978). In conjunction with the theories of mass strata movement in the vicinity of mine workings, the subject of surface subsidence predictions has also been the subject of extensive research. The development of reliable and rational techniques of subsidence prediction is imperative, if this phenomenon is to be recognized and controlled within acceptable environmental levels. Empirical as well as mathematical methods have been proposed to fulfill this objective and a comprehensive analysis of these methods has been presented in the literature (Bramer, 1973; Shad- bolt, 1978; Virginia Polytechnic Institute and State University, 1980). As a result of this intensive research effort, it is now accepted in many )coal fields-- mainly in Europe-- that the state of art in subsidence prediction and control has approached a level where mining induced surface displacements can be predicted to a suggested accuracy of less than + 20 percent. Furthermore, such movements can be translated into anticipated structural failures using established damage criteria, thus enabling appropriate precautionary measures to be implemented. In this country, subsidence is rapidly gaining emphasis as an important environmental problem of underground coal mining. Damage resulting from this phenomenon ranges from land settlement to severe structural damage and has been witnessed in rural (Illinois, Colorado, West Virginia, Virginia, Pennsylvania) as well as in urban areas (Pennsylvania, West Virginia, Illinois, Wyoming). Yet, the art of subsidence prediction and hence control in this country, for both longwall and room-and-pillar coal mining, is far from approaching the maturity reached by the Europeans. In this paper, field measurments and computer modeling techniques have been used to develop some basic relationships of longwall subsidence and its related parameters. Because the objective of this study was to develop regional subsidence trends, all processed information pertains to the Appalachian coal region.

Jan 1, 1981

By M. Kanefsky

Two channel polarity coincidence and polarity difference statistics are analyzed. The signal, common to both channels, consists of sinusoidal bursts where the exact frequency of the signal is nearly known, but other parameters such as amplitude, phase, and pulse starting time are unknown. The noise inputs are dependent, narrow band, Markov processes. It is shown that the performance depends not only on the signal uncertainties, but on the precise shape of the cross-correlation functions between the noise in-puts. By using two polairty difference statistics in addition to the polarity coincidence statistic, it is shown that the decrease in performance, as well as the cost of hard limiting due to correlated inputs, can be made small.

Jan 1, 1981

By W. H. Lang, C. H. Cox, H. Snell

The treatment of unaltered western phosphate ores by both wet and dry methods is discussed. The objective of the beneficiation is to produce salable Phosphate rock ( 31% P205), with an economic recovery of P205.

Jan 1, 1981

By I. R. Ward

"The need for energy conservation has been of increasing concern since the early 1970's, when the cost of petroleum based energy began to escalate rapidly and security of supply became uncertain. The cost of energy from alternative sources has also increased due to development costs and environmental restrictions.These developments have had a serious impact on the mining industry, which is energy intensive. The impact is magnified as lower grade ores are treated, and more energy is consumed per unit of product. In many cases increased operating cost is not compensated by the rise in product selling price.The magnitude of energy consumption in the mining industry is indicated by recent studies conducted in the U.S.A. and Canada. Based on 1970 figures, it was reported that the production of 1 ton of copper in the U.S.A. required 111. 8 x 106 BTU of energy, of which 60. 7 x 106 BTU (54.3%) was consumed in mining and processing (l)The survey of Canadian mills, conducted by CANMET and reported to the CMP meeting of 1978 (2), showed the following milling energy consumption figures (approximate averages):"

Jan 1, 1981

By Robert S. Mayo

My subject today is "Drilling-and-Blasting of Small Rock Tunnels". I am sure that there will be some people, primarily college students but perhaps Consulting Engineers, who will say: "Drilling-and-Blasting? I thought that went out with the invention of the Tunnel Boring Machine". A few years ago I talked to Dick Robbins and he told me that they did not try to sell a "Robbin's Mole" unless the tunnel was two miles long. For easy calculations I use 10,000-ft. (3km) A Mole today costs about $2 million which works out to $200 per lineal foot. This is "front money". You cannot place the order unless you are the uncontested low-bidder and then you must wait at least six months for delivery. Of course you can use that time to square up your portals, ready to turn-the-eye, or maybe you have shafts to sink to reach the tunnel grade. But this is "dead-time" and it is a heck of a feeling to have a job and cannot get started on it until you get the Mole. I do not have the American figures on lengths of tunnels but there was an article a few years ago in a British magazine: NEW CIVIL ENGINEER, on this subject. This stated that 75% of the jobs in Britain which were bid were for small tunnels, 10-ft x 10-ft (3m x 3m) or smaller, and that they were less than 5,000-ft (1.5km) in length. This does not mean that 75% of the footage in Britain was less than 10-ft in diameter. It means that 75% of the jobs being bid were less than a mile in length. From my experience in the U.S. I believe that we have substantially the same ratio: so many of the jobs with which I was associated were short, 1,000-ft, 2,000-ft and sometimes 3,000-ft and the bores

Jan 1, 1981

By E. J. Peterson

Oil shale retorting induces mineral and chemical reactions to occur on the macroscopic and microscopic levels in the kerogen-bearing marlstone. The nature and extent of the reactions is dependent upon process variables such as maximum temperature, time at temperature, atmosphere, and raw shale composition. This report describes the investigation of the mineral, chemical, and trace element release properties of spent shales retrieved from an experimental in situ retort at Occidental Oil Shale, Inc. 's Logan Wash site in Garfield County, Colorado. Correlation between mineralogy of the spent materials and the mobility of major, minor, and trace elements are indicated, and relationships with important process parameters are discussed. The progress .of carbonate decomposition reactions and silicat ion reactions is indicative of the processing conditions experienced by the shale materials and influences the mobility of major, minor, and trace elements when the solids are contacted by water. Shale minerals that are exposed to the extreme conditions reached in underground retorting form high temperature product phases including akermanite-gehlenite and diopside-augite solid solutions, kalsilite, monticellite, and forsterite. The persistence of relatively thermally stable phases, such as quartz, orthoclase, and albite provide insight into the extremes of processing conditions experienced by the spent shales. Leachate compositions suggest that several trace elements, including vanadium, boron, fluoride, and arsenic are not rendered immobile by the formation of the high-temperature silicate produce phase akermanite-gehlenite.

Jan 1, 1981

By Stephen Utter

One function of mining is to supply oil shale of the required grade and characteristics to surface retorts. The mining methods must he safe, efficient, and environmentally acceptable. Although the Bureau of Mines no longer conducts research on methods of mining fossil fuels, including oil shale, its many years of activity in that field resulted in a significant body of findings. This article summarizes some of these findings, with respect to oil shale mining. The large areal extent of Green River formation oil shales and the diversity of geologic, hydrologic, topographic, and other conditions, preclude the use of any one single mining and waste management technique. Instead, in most instances, methods and equipment will be chosen to meet site-specific conditions. Such methods include conventional surface mining (open-pit and strip), underground mining (room-and-pillar, sublevel stoping, caving) and in situ extraction (true in situ from surface drill holes and modified in situ from underground retorts containing rubblized oil shale). Combination or hybrid systems may prove suitable. Both surface and underground backfilling of spent shale waste may be practiced. Tremendous amounts of oil shale must be mined, processed, and the waste shale properly disposed of in order to meet projected industry production goals. For example, about 1.4 tons of oil shale averaging 117 L of shale oil per ton are required to produce one bbl of oil. A plant with a daily production of 8 dam' (50 000 bbl) of oil would thus require some 68 kt of raw shale daily. This is more than the average daily production from any underground mining operation.

Jan 1, 1981

By B. W. Jong

As part of the Bureau of Mines program to develop substitutes for critical and strategic materials for metallurgical applications, the Tuscaloosa Research Center has evaluated the effect of additives and starting materials on the sintering and strength properties of sialon (silicon-aluminum-oxynitride) compositions fabricated by conventional pressing and sintering techniques. Sintering and MOR (modulus of rupture) data were developed for sialon compositions produced from three components, Si3N4, A1203, and AIN. When doped with Y203 to aid in sintering, the highest MOR values were obtained with compositions containing between 20 and 30 mole-pet (A1203 + AIN). The effect of the crystalline phase of the Si3N4 and Al203 used in the three-component system on MOR also was investigated. Alpha-Si3N4 and ?-A1203 were found to be the best starting materials. A sialon composed of 67.4 mole-pct a-Si3N4 plus 32.6 mole-pct (?-AI203 + AIN), doped with 5 wt pct Y203, had MOR values at 25°, 1,200°, and 1,400° C of 40,300, 40,300, and 31,100 psi, respectively. Samples of this composition doped with Gd203, MgO, Zr02, and ZrSi04 also were evaluated. The ZrSi04-doped sialon had higher MOR values than Gd203-, MgO-, and Zr02-doped materials but lower MOR values than the Y203-doped sialon. The MOR values of ZrSi04-doped sialons were 25,000 and 25,900 psi, respectively, at 25° and 1,400° C.

Jan 1, 1981

By Keith A. Yarborough

INTRODUCTION The National Park Service (NPS) conducted a research program from mid-1975 to early 1978 to measure alpha radiation levels in natural caves which it administers. Subsequently, a long-term management program was developed which has conducted routine monitoring of radiation levels and has computed employee exposure accumulations in certain NPS caves. The overall program: research and management; was undertaken to evaluate the possible health hazard to cave visitors, interpreters, researchers, maintenance personnel, concessions employees and other workers and to protect their health. The results of this work have been reported extensively elsewhere (see References 1 through 3, 5, 6, 9 through 13, and 14 through 26). This paper deals with the relation of radon gas and daughter produced radiation levels to the cave air flows which mobilize them. These flows are a function of interior cave and exterior ambient air temperatures and pressures and of the cave's geophysical configuration. The low-level, ionizing radiation is produced by minute concentrations of radon and thoron gases which emanate from within caves. Because of confinement, the radiation levels are often appreciably higher than in surface atmospheres. Subsequent radioactive disintegration of the gases into their ionized "daughter" products, which are particulates, permits distribution of the alpha radiation throughout a cave system. The extent and character of this distribution depends upon the particular cave and the air flows which it produces. Thus, the alpha radiation serves as a "tracer" to describe the flows. The flow analysis is divided into two parts: 1) A qualitative description with respect to the two basic geophysical cave types over both long-term (annual) and short-term (diurnal to weekly) periods. 2) A quantitative description of the unsteady, uniform and non-uniform, one-dimensional, incompressible motions for both influent and effluent air flow situations in both basic geophysical cave types. A part of the qualitative description presents "Special Measurement" data: Tsivoglou [vs.] Kusnetz working levels, Tsivoglou individual daughter levels and free ion concentrations, radon gas concentrations, and equilibrium ratios. A great deal of important work has been carried out by Mr. Bobby C. Carson, Cave Radiation Technician at Mammoth Cave National Park, Kentucky. He reports these findings later in this conference (Ref. 6). Some of his results have been used here to establish the cave air flow analysis. Other National Park Service personnel have made measurements at others of the caves for which data are reported here. All of this work and cooperation has been vital to the success of this research program. It is very much appreciated. THEORETICAL FLOW DESCRIPTION Previously reported research (See Ref's. 20, 21, 23 and 25) has established the qualitative relationship between the alpha radiation in caves and their natural air flows. The radiation serves as a representation of these air flows. Changes in radiation with time represent changes in the main forces which produce the air flows. The quantitative data have substantiated that [all caves in which the primary cause of air flow is due to temperature produced gravity (density) gradients and also having minimal man-made disturbances, experience seasonal variations in airborne alpha radiation. The radiation levels increase in summer but decrease in winter], based upon seasonal air movements through each cave system which occur naturally. Two general types of physical cave configurations which control the air flows have been identified as: 1. Those which go up into a hillside or mountainside: Type I ("Upside-down" = USD). 2. Those which go down into the earth; Type II ("Right-side-up" = RSU). These act to control the air flows seasonally. The summer increase in Type I caves is due to increased air flows, whereas in Type II caves it results from stagnation or reduced air flows. This seeming paradox is explained by the physics of the air flow regime in each cave type and has been detailed elsewhere [Ref's. (20), (22) through (25)]. It[ i] true, in general, that air flow decreases airborne radiation in the [immediate vicinity] in which it occurs. Any paradox results from subsequent distribution throughout the case as to [ how] the air moves through a cave [system] with respect to time and space. Exceptions to the cave air flow "rule" are: 1. Caves in which pressure gradients and pressure fluctuations [predominate] in producing the air flows. 2. Caves in which man-made effects and management practices are superimposed on the natural air flow regime. Man-made disturbances which can alter the natural cave air flows are tunnels, elevator shafts, bore holes, sealed and closed portals, etc. If these are not properly sealed, the natural air flows which they change will totally alter the distribution and seasonal variations of the alpha radiation levels. These exceptions may act separately or in combination.

Jan 1, 1981

By Thomas J. Witzig

This Bureau of Mines report is a background study of the International Tin Agreement. Attempts at stabilizing the tin market prior to the agreement are detailed, as well as the conditions and negotiations that set up the agreement. Details of the five consecutive 5-year agreements beginning in 1956 are presented, with emphasis on membership and the agreements' primary tools: the buffer stock and export controls, Attention is focused throughout on the United States activities during the period, especially with regard to its strategic stockpile, and its involvement with the agreement culminating in its membership, for the first time, in the fifth agreement beginning in 1976. Considerations leading to the U.S. decision to join are detailed, and U.S. activities in the negotiations for the sixth agreement are presented. The status and outlook for the agreement are discussed, and evaluations of the effectiveness of the agreement and its components are reviewed.

Jan 1, 1981

By Won C. Park

Experiments showed changes in the mineral content of dolomitic oil shale at temperatures and exposure times which bracket conditions encountered during in situ retorting. Laboratory results correlate with cores from a spent in situ retort at Occidental's Logan Wash test site at Garfield County, Colorado. Dolomite, CaMg(CO3)2, decomposes rapidly to form periclase, MgO, calcite, CaCO3, and CO . Both calcite and periclase are intermediate products that can be stabilized by CO atmosphere at lower temperatures, while steam accelerates the formation 2 of silicates. The decarbonation of calcite appears to involve a direct reaction with both quartz and periclase in forming these silicates. Decarbonation preceeds the formation of akermanite, Ca2 MgSi 207, and diopside, CaMgSi 206, within several hours of heating and is followed by the nucleation of forsterite Mg2SiO4, and monticellite, CaMgSiO4. Under in situ retorting conditions, akermanite and diposide are the major minerals above 800°C. Equilibrium is not attained within 200-300 hours. In situ retorting temperatures above 800°C for extended periods of time should reduce potential ground water leaching by the formation of silicate minerals. These silicates are less soluble than free lime, magnesium or alkali oxides. There is a corresponding decrease in the natural pH of these silicates from approximately 12 down to 7.5 to 9:

Jan 1, 1981

By LeoJ. Miller

Exploration for an ore deposit commences with an outline of the regional ore controlling environment and is followed by the application of tools to focus the target area. One of the most essential focusing is the mapping of the mineral assemblages within the area of the ore. Key elements of mineralizing fluids, either epigenetic or syngenetic, enter into mineral assemblages that extend far beyond ore deposits. Portions of these assemblages may consist of new matrix minerals or alteration of previously existing minerals. Today, ore deposits are divided into genetic classes and each class is d8fined by a specific geological environment. Ore deposits within a given class are associated with a mineralogy, that is characteristic of the ore deposit class. So faithful is the mineral assemblage surrounding, or within an ore deposit, that recognition of the assemblage may be sufficient to define the class. Porphyry copper deposits have long been noted for their halos of alter-ation minerals. The outermost ring of chlorite, epidote and calcite extend thousands of feet away from the main ore zone. The mineral associated with porphyry copper deposits have been well documented by our distinguished speaker Paul Kerr, at Santa Rita (1), and Silver Bell' (2), and by excellent papers from S. C. Creasey, 1959 (3), Sales, 1948 (4), T. S. Lovering, 1949 (5), our Co-Chairman John Guilbert, 1970 (6), and many others. Several recent porphyry copper mines have been discovered in recent years by utilizing the mineral assemblage model described by Lowell and Guilbert, 1970 (6). Dave Lowell applied his own model of mineral halos for the discovery of Kalamazoo at San Manuel (7), Arizona, and Casa Grande West, Arizona. The purpose of this paper is to outline the application of mineralogy for discoveries of deposits other than porphyry copper mines and in particular, to ore discoveries in which mineralogy has played a key roll.

Jan 1, 1981

By Y. Kurokawa, R. Kurosawa, I. Iwata, I. Fukuoka, N. Sugita

INTRODUCTION The Ningyo-toge Mine is located in the western part of Honshu, about 800 km from Tokyo. Since the discovery of uranium ore deposit at Ningyo-toge in 1955, different kinds of mining and milling tests have been carried out. A new pilot plant of milling and UF6 conversion is also being under construction. Operations are scheduled to start by the end of this year. In 1979, the uranium enrichment pilot plant was constructed at Ningyo-toge and test operations have started. Thus, the Ningyo-toge area is assigned to undertake the Research and Development of the upstream of the nuclear fuel cycle in Japan. PNC has been strengthening its security measures more than ever. This paper will focus on the disposal of wasted material, especially on the disposal of heap leaching residue, in Japan. URANIUM ORE DEPOSITS The uranium of the Ningyo-toge Mine is characterized genetically by epigenetic sedimentary type deposits. They occur in the host rock of Neogene tertiary fluviatile conglomerates and sandstones which unconformably overlies the Mesozoic-Palaeogene granitic basement covered with lucustrine deposits and volcanic ejecta. More than 12 deposits have been found over the area of approximately 160 km2, and distribution of the deposits are strongly controlled by the so-called channel structure, probably remnants of paleo-streams on the denudation surface of the underlying grantic basement. Each ore body has different shape and dimension respectively, but about 2-3 meters thickness with the average grade of 0.05-0.2% U308 is common feature of the ore bodies. The ore is soft and loose, and it is composed of common rock forming minerals of allogenic origin and their altered products. The chemical composition of the ore depends on the constituents of the country rocks or the pebbles. A primary mineral, ningyoite and secondary mineral, autunite are major ore minerals, although three primary tetravalent minerals and thirteen secondary hexavalent minerals have also been detected. MINING EXPERIMENT Since 1959, various types of underground mining tests have been carried out at Ningyo-toge Mine. The room and pillar method was safe and simple, although the uranium ore recovery was below 70%. After experiment of the retreating long-wall method and slicing mining method, it was found that the modified long wall method was the most appropriate for the underground mining of the Ningyo-toge uranium deposits. This method was completed successfully to increase efficiency up to 2 or 3 times, as compared to conventional methods. MILLING EXPERIMENT In 1964, a small test mill was constructed at Ningyo-toge, and a milling experiment using the Ningyo-toge uranium ore was started. Re-modelling of equipments and improvement of the process lead to the establishment of the technique of the so-called wet process, and produce UF4 directly from the ore. The flow diagram is shown in Fig. 1.

Jan 1, 1981

The planning, design and construction of a service tunnel, under a major arterial road between two hospitals are described. The multiple uses of the tunnel combine to provide a favourable cost-benefit ratio for the tunnel as part of a rationalisation of services between hospitals. The driven tunnel provides economic, program and approval advantages over that of a cut and cover construction. The cross sectional shape of the tunnel was determined during feasibility studies by the degree of weathering of the Silurian mud- stones, the shallow cover and the proposed excavation equipment as well as the functional requirements. The site investigations covering geotechnical, building, noise and level surveys provided input to the design documentation and construction phases. Monitoring of settlement levels and primary support stresses during early construction stages confirmed the adequacy of the proposed tunnelling methods and support to be used adjacent to the major building foundations. The 140 metre long tunnel was success- fully completed in April 1980 at a cost of $650,000.

Jan 1, 1981

By J. G. Strasser

"There has been considerable output over the last three decades from the social sciences concerning man and his working environment. In the mining industry at large, however, authoritarian, hierarchical control systems remain the norm, and it can be argued that something less than optimum effectiveness in terms of both productivity and worker satisfaction has resulted.Recently (/975), Campbell Chibougamau Mines Ltd. devised a most interesting organization and incentive system that links the underground production of a standard ton of mined output at controlled grade to an incentive payment scheme. A parallel scheme in the mill complex is based on maximizing recovery of copper and gold from available feed. A key part of both minsystems is the formation of groups who have considerable autonomy, particularly when compared to the still prevalent traditional mining industry relationships between the worker and supervisory levels.This paper traces the development of Campbell Chibougamau's system . Attention is drawn to qualitative and quantitative measures of the success of the method through the commentary of those miners involved in the scheme, and by reference to the favourable records on productivity, absenteeism, safety, turnover and grievance activity.IntroductionPyramidal or hierarchical management control systems, coupled to piece-work incentive schemes, predominate throughout Canada's underground mining industry. Although specific details of such systems vary from site to site, they , are generally understood and accepted as fact by the majority of the work force.Normally, a front-line supervisor (shift boss) directs a number of workmen and assigns them to tasks and working locations commensurate with their abilities, knowledge, training and skills. This front -line supervisor may direct or supervise from as few as 12 to as many as 75 or more workmen. He issues orders according to his assigned production objectives and ensures that these directions are fulfilled in accordance with standard mine practice . Several shift bosses are usually directed by a mine foreman or mine captain. The mine captains report to a general foreman or directly to the mine superintendent or his assistant, depending on the size and scope of the operation."

Jan 1, 1981

By Daniel H. Isreal

Because the federal government owns and controls nearly 80% of the most valuable oil shale reserves in the West, it is inevitable that federal leasing and siting will play a prominent role in development of an oil shale industry during the 1980s. Also, because of recent enactment of the Synthetic Fuels Corp. authorizing up to $88 billion in loan and price guarantees-federal financing will provide the critical incentive to permit private investment in a still infant industry.

Jan 1, 1981