Search Documents

In North-West Nelson the Riwaka Complex, a linear basic intrusive complex, is exposed for approximately 45 km. Some 500 km south, across the Alpine Fault, a linear zone of similar but less well known basic intrusives that may be correlatives of the Riwaka Complex is exposed discontinuously for about 80 km. The Complex was emplaced at several centres along a major tensional fracture zone that developed in upper Carboniferous to Lower Permian time. This fracture zone probably formed in response to the development of a west dipping subduction zone that gave rise to the Permian volcanic arcs in east Nelson and western Southland. The Riwaka Complex contains three rock suites. The Fractionation Suite, characterized by cyclic mineral layering and small scale cumulus banding is the largest and is divided into the Ultramafic, Hornblende and Plagioclase Series, each of which is subdivided into several units. The Cumulus Gabbros represent a restricted but important suite of unusual composition, while the third suite is the late phase Diorite Suite. Except in the lower units of the Ultramafic Series sulfide mineralisation is widespread. Pyrrhotite is the dominant sulfide with lesser chalcopyrite pentlandite and pyrite. Four significant zones of sulfide accumulation are recognised and discussed in some detail. Evidence suggests that the primary magma from which the Riwaka Complex was derived was sulfur deficient. It is concluded that the sulfur content of the Riwaka Complex was derived from assimilation of sulfur rich wall rocks during intrusive processes.

Jan 1, 1980

By Dermot Macaragh Ross-Brown, Brian Stimpson

Borehole information is often the only source of information on rock conditions at depth during the stage of feasibility studies of a project, and from this data the rock mechanics engineer would like to make some quantitative estimates of rock mass cohesive strength. While judgement and experience will usually play a paramount role at this stage, simple tools for estimating rock mass cohesive strength would be an asset. In this paper, an approximate technique is suggested for assessing the cohesive strength of a randomly jointed rock mass from borehole data on fracture intensity and intact rock strength.

Jan 1, 1980

By Lyle W. Talbotr

The DeLamar Silver Mine is a Joint Venture between Earth Resources Company, the Canadian Superior Mining Company and the Superior Oil Company. The property is a consolidation of several old operations in the district. The more widely known are the DeLamar and Sommercamp Mines. The location is 20 miles northeast of Jordan Valley, Oregon and 55 miles southwest of Boise, Idaho. The mine is on the south slope of DeLamar Mountain in the Owyhee Mountains of southwest Idaho Initial interest started in 1969 with serious exploration beginning in 1970. The feasibility study was completed in 1974, and in 1975 Mountain States Engineers were retained to design and build the plant. Processing of ore began in March of 1977 with the first bullion poured in April of that year. The plant is currently processing some 2200 TPD of ore with a grade of four ounces of silver and 0.03 oz. of gold per ton of ore. Cyanide consumption is 2.5 lb/ton, zinc consumption of 0.3 lb/ton and flocculent consumption of 0.5 lb/ton. A flowsheet is shown as Figure I. The grinding circuit is of two stage design. The primary mill is an 18 ft. dia. by 9 ft. long semi-autogenous unit. The secondary mill is a 9 1/2 ft. dia. by 15 ft. long overflow ball mill. The mill discharges are combined and sent to 15 in. cyclones for classification. Cyclone overflow reports to leaching with the underflows reporting to the ball mill. The cyclone feed pump is an 8X6 metal case pump. The primary mill has 1000 installed horsepower and rotates at 68% of critical speed. The ball mill has 700 installed horsepower and rotates at 72% of critical speed. Because the primary mill is horsepower limited the ball charge is varied to maintain the desired throughput. The mill power is held at 980-990 HP by modifying the feed rate. Four inch forged steel balls are added any time the ore feed fails to reach 100 tons per hour for four hours. During periods of extremely hard ore, the ball charge has been as high as 14 v/o and at other times the mill has operated fully autogenous for weeks.

Jan 1, 1980

The process of hydraulic transport through pipelines, worldwide well known for the transport of fine-grain solids is also being used to a greater extent in mining for the handling of primarily coarse-grain solid û water mixtures for the removal of, for instance û coal and waste mixtures after coal winning using hydraulic monitors, tailings for backfilling underground and washer tailings and flotation waste to the dump. A large-scale test unit was taken into service at the Bergbauforschung GmbH (Mining Research Company) in Essen-Kray, GFR, to further improve this technology. The unit was planned and built by Krupp Industrie- und Stahlbau of Duisburg in cooperation with Bergbauforschung GmbH. The paper deals in detail with the demands made on this test unit and the technical results obtained on it and with the planned experimental research work.

Jan 1, 1980

[This Bureau of Mines report presents results of a survey of underground mining equipment and of two demonstration programs showing the feasibility If quieting; a load-haul-dump (LHD) machine and a personnel vehicle. Typical noise levels are presented for the major machine types used in underground mines, along with estimates of the noise overexposure of miners who operate or work near these machines. General principles of noise control are explained, and the application of these principles is illustrated in the description of modifications made to the LHD machine and the personnel vehicle. The noise control package installed On the persona of vehicle lowered its noise level by 14 dBA after 4 months of operation, and inspection of the LHD machine after 2 1/2 years of operation with the modifications showed its noise level 7 dBA lower than that of the unmodified machine. Noise dosimeter measurements indicated that both machines were in compliance with Federal noise regulations for a typical shift.]

Jan 1, 1980

By J. Roger Loebenstein

Demand for arsenic trioxide exceeded supply in 1978 and 1979, and the major domestic and foreign producers allocated available supplies to customers. Major demand has been from the cotton-growing and wood-preserving industries. Ample supplies of arsenic metal produced in the United States and Sweden were available in 1978 and 1979. Major demand for metal was from the automobile battery industry in Japan, Europe, and the United States. Legislation and Government Programs.-The Occupational Safety and Health Administration (OSHA), promulgated the final standard on the occupational exposure to inorganic arsenic, effective August 1, 1978.2 The need for the standard was a result of OSHA's conclusion that inorganic arsenic is a human carcinogen. The purpose of the standard was to minimize the incidence of lung cancer among workers exposed to inorganic arsenic. The maximum exposure to arsenic was lowered from the previous ceiling of 500 micrograms per cubic meter of air to 10 micrograms per cubic meter over an 8-hour time period. OSHA had originally recommended a ceiling limit of 4 micrograms per cubic meter in January 1975. Provisions of the new standard require exposed employees to wear respirators and undergo continuous medical monitoring. Other provisions establish regulated areas limited to authorized employees and require the construction of special lunch-room and worker hygiene facilities and the posting of signs and labels warning of the presence of arsenic. The new arsenic standard will have a significant economic impact on copper, zinc, gold, and lead smelters as well as consumers of arsenic trioxide. A number of copper companies have joined together to contest the standard in court. However, measures to comply with the standard have been initiated by ASARCO Incorporated at its Tacoma, Wash. plant.

Jan 1, 1980

By Peter Riba

Up until ten years ago the industry had arrived at a relatively conventional, and consistent design of coke ovens. Through the years the designers and builders were not being heavily taxed to come up with revolutionary new designs. However, the stimulus for design change was ever present. These stimuli for change are quite important and they are the driving force which produce improvements. The most obvious stimulus to change a design is commercial. To "build a better mouse trap and the world will beat a path to your door" is the well used cliche which best befits this philosophy. As in all businesses, coke oven designs require that all of the considerations, which affect the cost or the desirability of the design, be optimized. One way to increase the desirability of the particular design, 1s to make the design in- expensive to operate. Or, put another way, to increase production for the same operating cost

Jan 1, 1980

The major copper orebody at Mount Isa is being extracted at a rate of four million tonnes per year. The method used requires an equivalent rate of back filling with (mainly) cemented fill. There were three major incentives for developing this mining system. The first was the prospect of high ultimate recovery of the orebody. The target is 100% recovery. Also the proposed stoping layout appeared to offer significant advantages in development and production costs. Finally, extensive subsidence above the northern end of the orebody could have disturbed permanent surface installations and jeopardised a possible future open cut. The full implications of this ambitious strategy were not apparent in the early years. Now, after twelve years of production the benefits are being realised and they can be weighed against the costs. Probably the most interesting result which comes from this analysis is the significance of cutoff grades and dilution factors in balancing mining and filling rates.

Jan 1, 1980

By Malcolm J. McPherson

The highest recorded loss of life due to the collapse of mine workings occurred at the Coalbrook North Colliery in South Africa on 21st January, 1960. A total of 437 persons died when bord and pillar workings collapsed over an area exceeding one square mile The whole mass of strata from the 470 ft (143 m) deep seam to the surface being affected. Although the Coalbrook disaster was unique in its scale the problem of pillar failure, particularly in old workings, is by no means uncommon nor confined to recent history. Indeed, the collapse of large pillared areas was a regular feature of mining in the north of England in the early part of the nineteenth century. When a section of underground workings collapses, the air under the descending roof is compressed very rapidly. The pressurised air is dissipated subsequently at a rate governed by the leakage paths available. If the collapsing area is small, such as the case of a local fall of roof, then there will be little danger of an air blast. If, however, an extensive area collapses suddenly then the rapid compression of air will give rise to a pressure shock wave that will be transmitted through the remaining workings as an air blast. If worked out areas are connected to current workings via unstopped airways an air blast caused by pillar failure in the old workings will be extremely hazardous to personne1 and may cause extensive damage to equipment, perhaps even reaching to surface plant. At Coalbrook, the air blast blew out a wall in the surface fan house. Areas that are considered liable to sudden collapse may be isolated from current workings by the construction of stoppings. However, such stoppings must be capable of withstanding the 'hammerblow' effect of peak air pressures developed during the collapse. The work described in this paper was undertaken in order to determine the maximum air pressures that stoppings must withstand during a major pillar failure. The result has been a method of establishing peak air pressures that is quick and simple to use. Readers who are concerned primarily with the practical application of the method are advised to turn directly to the last main section of the paper.

Jan 1, 1980

By Edward A. Nowatzki

The purpose of this paper is to present an example of the application of a theoretically derived mathematical model for track-soil interaction to the evaluation of the mobility of large-scale mining equipment used in open pit operations. The model described by Karafiath and Nowatzki (1978) and presented in detail by Karafiath (1978) was used to predict the performance characteristics of four different bucket wheel excavators (BWEs) on rwo types of copper mill tailings at various moisture conditions. The BWEs considered In the analyses are two-and three-tracked continuous excavators. Most have boom-mounted rotating buckets and swinging side- or rear-discharge conveyors. The analyses were performed at the request of Dames and Moore for the Kennecott Corporation's proposed remining of selected tailings deposits at the McGill, Nevada, concentrator. The objectives of the analyses were to determine whether BWEs would have sufficient mobility In the tailings deposit to achieve satisfactory production rates, and TO compare the predicted performance of the various BWEs evaluated. Good qualitative agreement was obtained between the results of the theoretical analyses performed for the McGil1 operation and the actual performance of BWEs in two South African gold mine tailings impoundments.

Jan 1, 1980

By B. K. Parekh, W. M. Goldberger

A novel process is proposed for continuous removal of ash and unreacted solids which become suspended in the oils obtained during coal liquefaction. The proposed method uses water in direct contact with the oil under conditions which cause the suspended residue solids to transfer from the oil to the water phase. Separation of the phases yields a product oil essentially free of suspended solids. The water is cooled, clarified or filtered by conventional low-cost systems, and recirculated. The paper describes experimental work leading to development of the novel concept and includes the result of batch experiments that establish the feasibility of the process.

Jan 1, 1980

By Stephen W. Lambert

One of the primary interests of the United States Department of Energy's Mine Planning Division is to fully develop avenues of technical research which potentially offer positive effects on coal mine productivity. One such area of research involves the removal of methane gas from unmined portions of coalbeds through vertical wells drilled from surface locations. As coalbed methane content is reduced, less gas is available for flow into the mine, and consequently ventilation requirements are decreased and/or coal extraction rates increase. Another attractive aspect of the vertical borehole drainage method is that it presents an opportunity to recover and utilize significant quantities of methane gas, which would otherwise be wasted to the atmosphere. The viability of removing gas from the Mary Lee coalbed using stimulated vertical boreholes was first suggested by Elder and Deul as a result of a United States Bureau of Mines' drilling project conducted from 1971 to 1974 (4). Other United States Bureau of Mines' studies forecasted that degasification would eventually be necessary in the Mary Lee coalbed because most new or expanding mine development would take place at depths exceeding 1 000 feet (305 meters), where the methane problem would be severe (3) (13). In 1975 a large-scaled drilling program was designed in order to supply industry's anticipated need for a degasification technology in the Warrior coal basin, Alabama. The results of this government/industry sponsored effort were to be specifically applicable to the Mary Lee coalbed, the most extensive and economically important deep minable coal present in the area. Major technical objectives of this program are twofold: (1) to measure the effects of various well completion designs, particularly hydraulic stimulation, on mining and (2) to determine the effects of well spacing on gas drainage rates. A cooperative agreement was established with United States Steel Corporation in late 1975 and field work began shortly thereafter in the proximity of a newly developing mine near Oak Grove, Alabama. Government responsibility for this program was transferred from the United States Bureau of Mines to the United States Department of Energy in October 1977. To date, as a result of this program, twenty-one wells have been completed into the Mary Lee coalbed at the Oak Grove site. Seventeen of these wells were drilled on an experimental grid pattern located two miles from the active mine. These grid wells are primarily being used to generate data necessary to determine the effects of well spacing on gas drainage rates and will also provide a large amount of information regarding the long-term effects of degasification on mining. The four remaining wells (designated Ton through TW4) were placed near the mine so that the full effects of completion could be studied within the short time required for underground interception. Results gathered from the first two test wells (TW1 and TW2) have been reported in detail (10) and indicated that several improvements were necessary to increase gas drainage rates. Hydraulic stimulation was one of the most important aspects of well design that required improvement. Nitrogen-charged foam stimulation treatment was used at TW3 and TW4 instead of the gelled-fluid type stimulation used at the first two near-mine test wells.

Jan 1, 1980

By Seth C. Schaefer

[As part of the Bureau of Mines effort to provide thermodynamic data for advancement of mineral resources technology, the standard Gibbs energies of formation (?G°f) of MnS (manganese sulfide) and Fe0.9 S (pyrrhotite) were investigated with a high-temperature galvanic cell employing stabilized Zr02 (zirconia) as the electrolyte. Potential measurements were obtained for the cell Pt, MnS, MnO, S02 (g, 1 atm)//Zr02//02(g, 0.0114 atm), Pt with the overall cell reaction MnS (s) + 1.5 02 (g, 0.0114 atm) = MnO (s) + S02 (g) . (1) These results give the standard Gibbs energy of formation of MnS for the reaction Mn (s) + 0.552 (g) = MnS (s) (2) ?G°f = -66.487 + 15.19 x 10-3T±0.207 kcal/mole (896.4 - 1,208.1 K) (3) where temperature (T) is expressed in kelvins. Similar measurements were obtained for the cell Pt, FeO .9S, Fe304 , S02 (g, 1 atm) //Zr02//02 (g, 0.0114 atm) , Pt with the overall cell reaction 10/3 FeO .9 S (s) + 16/3 02 (g, 0.0114 atm) = Fe.,04 (s) +10/3 S02 (g). (4) These results yield the standard Gibbs energy of formation for the reaction 0.9 Fe (s) + 0.5 S2 (g) = Fe0.9 S (s) (5) ?G°f = -35.229 + 12.67 x 1073T+-0.104 kcal/mole (839.5 - 1,086.6 K). (6) A third-law analysis of MnS data yields a standard enthalpy of formation (AH°f) for the reaction Mn (s) + S (rh) = MnS (s) (7) ?H°f298 = -51.16±0.21 kcal/mole (8) A similar third-law analysis for Fe0.9S data yields a ?29°f298 for the reaction 0.9 Fe(s) + S(rh) = FeO .9S(s) (9) ?HO\°f298 = -24.01±_0.15 kcal/mole. (10) ]

Jan 1, 1980

By Regis F. Kopac

With the growing dependence on coal as an energy source, finding a means to prevent or reduce the freezing of coal during winter shipment has become increasingly important. Several chemical companies focused on this problem and applied chemical technology to develop suitable solutions. As a result, a number of freeze conditioning agents have been introduced in the past few years, several of which have been highly effective in controlling frozen coal. The efficacy of these chemicals has been well established, however many users have found that only a well defined program will produce acceptable results at a reasonable cost. Positive program results yielding recognizable benefits have caused many power generating and coking plants to consider freeze conditioning agents. A freeze conditioning agent (or FCA) has been defined as a multi-component organic liquid designed to be sprayed on coal particles at bulk shipping points to assure that receiving locations will be able to unload, store and use the treated coal with minimum delay or inconvenience. The chemicals are generally applied at rates of 1 to 2 pints (0.473 to 0.946 liters) per ton and normally function by changing the crystalline structure of water left on the coal during processing. The bond strength of the ice that may subsequently form is markedly reduced. Instead of freezing into solid, unmanageable masses, the coal can be easily unloaded by rotary dumping or the opening of hopper car doors.

Jan 1, 1980

Arsenic.--Inorganic arsenic has been added to the Environmental Protection Agency's list of hazardous air pollutants because of a high probability it can cause cancer. EPA estimates that inorganic arsenic emissions into ambient air total more than 6,000 tons per year, with about 65;L of this coming from the operations of copper, lead, and zinc smelters. Asbestos Detection.--In June 14, the President signed S. 1658 providing $172.5 million to detect and remove asbestos hazards in schools. Asbestos Use Must be Reported.--All firms using asbestos in the manufacture of some 30 categories of products must describe in detail how they use the mineral to the Consumer Product Safety Commission, for all manufactures since January 1, 1977.

Jan 1, 1980

By D E. Gadd

Since October 1972, New Zealand Steel Mining Ltd has loaded around ten million tonnes of ironsand concentrate from single-point mooring buoys located off-shore at Taharoa on the west coast of the North Island of New Zealand. Before the first off-shore loading system was installed a considerable research effort was applied to proving the slurry loading technique. Subsequently the system has been expanded and a new buoy, pipelines and pumping system were installed in early 1978. Since then 110 000 DWT class ore carriers have been loaded at rates of around 2600 tonnes per hour through twin submarine pipelines. This paper reviews the operation of the ship loading system and attempts to answer the question: 'If the Taharoa operation were to be planned in 1980, would the same research spending be necessary or have published research results since, made such practical tests unnecessary?'

Jan 1, 1980

By Coronel PT

Like companies in other sectors of industry, mining companies are experiencing significant problems with low labour productivity, high labour turnover, and accidents. Increasingly, companies are recognising that good training is a vital factor in dealing with these problems. One such company is Aberfoyle Tin Limited. Early in 1979 the company engaged P.A. Consulting Services Pty. Ltd. (P.A.) to upgrade and formalize its miner training procedures. P.A. developed a programme using their Process Analysis Method of Training (P.A.M.T.) and trained a company trainer in its use. As a result of its application and the establishment of a formal training school, the rate of production of trained miners has been greatly increased. Despite some problems caused by lack of resources at the mine, the trainees graduating under the new scheme have been shown to be of comparable standard to those produced by the previously used "on the job" training method.

Jan 1, 1980

By F. A. Baczek

The Electroslurry TM electrowinning concept has been incorporated into a process flowsheet for recovering copper from smelter flue dusts. The process has averaged 96% recovery of the copper as high-grade electrowon while at the same time removing a majority of the impurities that degrade drawn copper as a result of recycling flue dust and liberator cathodes: The dust is processed through several stages consisting of leaching, copper precipitation, Electroslurry TM electrowinning and waste liquor treatment. The process may be integrated into a smelter operation and become an effective and feasible means of maintaining good product purity.

Jan 1, 1980

By Arthur F. Colombo

The selective flocculation, desliming and flotation process developed by the U.S. Department of the Interior, Bureau of Mines, as part of its goal of maintaining an adequate supply of minerals to meet national economic and strategic needs is described. The application of the selective flocculation and cationic flotation process to three oxidized taconites from the western Mesabi Range in Minnesota is discussed. Data from the operation of a 408-kilogram-per-hour (900 lb/hr) pilot plant employing reclaimed water are summarized for the three types of oxidized taconites.

Jan 1, 1980

By Eduard Hamm

The main reasons for the development of higher heat levels in German coal mines are the increasing depth of working with the con- sequent higher rock temperatures, increased use of electrical equipment, and increasing coal output due to concentration and mechanisation of workings. In place of the normal decentralised underground cooling plants, schemes and pilot plants have been developed to produce the required cooling capacities in central air cooling units, which then supply the cold air to the underground working points where needed.

Jan 1, 1980