Search Documents

By Kelly E. G

New Zealand suffers the disadvantage of widely scattered ore bodies, none of which is large enough to economically support its own smelter. This leads to the concept of a centrally located smelter which must be flexible enough to cope with var

Jan 1, 1980

By James H. Russell

The Bureau of Mines, U.S. Department of the Interior, in cooperation with the Department of Energy, has attempted to increase the activity of nickel catalysts for converting synthesis gas, derived from coal, to a substitute natural gas. This report describes the effects of low-level additions of B, Ca, Ce, Co, Mn, Mo, Pd, Re, Ti, Y, Zn, and Zr on the methanation activity of Raney nickel. The methanation rate at 320° C and the resistance to poisoning by 2 ppm H2S were used to compare catalysts. The effects of the additions were small, and the experimental variances were large, necessitating the use of statistical methods to identify significant effects. Co, Ti, Y, and Zn improved the resistance to H2S poisoning, but only Co improved the methanation rate In some individual catalysts containing Ca, Mo, or Mn, both the methanation rate and resistance to H2S poisoning were improved.

Jan 1, 1980

By Tyler Blake

This report describes a study designed to evaluate a pro-posed modification in the cap lamp battery cord intented to reduce the incidence of snagging and catching of the cord. A three phase evaluation was performed comparing a prototype with the standard, currently available cord. First, a ?pull test? equipment was run. The second evaluation was a body conformity study. The third evaluation involved subjects performing common tasks in a low seam coal mine simulator. The results of these evaluations clearly demonstrated significant safety advantages of incorporating coiled cord into the design of the cap cord. The coil cord presented less of a snagging hazard, allowed the wearer more time to respond to a snag, and transmitted lower levels of force to the helmet when snagged. The research team recommended that cap lamp cords be commercially developed which incorporate coiled cord at the battery and helmet.

Jan 1, 1980

By R. Hogg

INTRODUCTION The principal applications of the flocculation process in the coal industry lie in the area of waste water treatment. Consequently, the concern is more with the behavior of the associated minerals, clays for example, than with the coal itself. At the same time, however, the presence of even small amounts of fine coal can significantly influence the performance of the flocculation operation. Coal preparation waste water treatment is a substantial problem involving over 200 billion gallons of water annually. There can be no doubt that these quantities will continue to increase as coal production increases and environmental considerations dictate the increased use of closed circuit systems and tighter control of effluent quality. Furthermore, we can expect to find a continued increase in the amount of fines generated in the coal mining and processing operations. Modern mining techniques tend to yield a finer raw coal with a higher ash content. The greater emphasis on fine coal cleaning for improved sulfur and ash removal and increased coal recovery will also lead to greater demands being placed upon the wastewater treatment system. The costs of "blackwater" treatment have been shown to vary widely from plant to plant (1). Part of this variation can be attributed to differences in the coal being mined and the plant flowsheet but there are no doubt significant contributions from the improper design and operation of treatment facilities.

Jan 1, 1980

By M. J. Pearse

The processing of fine particles inevitably produces slimes. These present a dewatering problem, for which gravity thickening provides a partial or preliminary solution. The paper shows the effects of practical factors in carrying out laboratory sizing tests for thickeners. Several methods of determining thickener unit area have been compared for a lightly coagulated phosphate slurry and a highly flocculated kaolin slurry. Practical techniques of mixing and flocculant addition have significant effects on batch settling data. Pulp temperature and cylinder dimensions are very important. Errors in sizing thickeners for highly flocculated slurries by the standard methods are discussed. Such methods are suitable for less compressible slurries, however. Rules of thumb for flocculant selection are given.

Jan 1, 1980

By J. D. Austin, D. G. Kringe

Rates of return realized on investments in the gold mines of the newer goldfields outside the Witwatersrand were calculated and analysed over various time intervals and on various bases. It is shown that these rates of return are strongly correlated with changes in the gold price and cannot be equated with the returns that are expected when investments are made, and that the changes in gold price also affect the rates of return on the Johannesburg Stock Exchange as a whole. These correlations are used, together with a limited application of the Capital Asset Pricing Model, to suggest the expected levels of threshold returns in real terms for new mining projects, for projects on existing mines, and for share valuations.

Jan 1, 1980

By B. Pitchumani, D. Venkateswarlu

INTRODUCTION The characteristics of feed and product of any size reduction operation are normally expressed as mean size, the size corresponding to 80 percent undersize or the percentage below a specified size or specific surface area. But the feed has a distribution of sizes and quite often it becomes essential to obtain a product of desired distribution. In such cases, size distribution of feed is related to product by matrix methods. The technique of matrix representation of crushing operation was proposed by Broadbent and Calcott (1 to 4). They divided the complete crushing mechanism of coal into breakage, selection and classifying functions for a closed-circuit system to establish relations between the feed and product distribution. Ellis, Ray and Venables (6) suggested an empirical method of determining the breakage matrix by combining the characteristic functions and proposed the following hypotheses: 1. The breakage of individual size fractions passing through the mill at a given rate is the same whether passed separately or as part of a mixed feed. 2. The breakage of a mixed feed may be estimated from the products of individual size fractions passed through the mill separately at a rate at which they would be crushed as part of the mixed feed. This method is stated to be applicable when there is no interaction between the individual sizes.

Jan 1, 1980

By P. Sen, H. B. Barani, P. Sen Gupta

A critical review of the various separation efficiencies reported in literature has been made. Most of the relationships used for evaluating the performance relate to screening, classification, or concentration operations and are applicable to single-stage, two-component systems only. In the present work, a much simpler approach has been used for assessing the separation process irrespective of the type of operation and this has been extended further to obtain an expression for a multicomponent feed and multiproduct (from a multistage operation) system.

Jan 1, 1980

By Steven J. Page

Responding to the increasing concern for dust control in metal and nonmetal mining, the Bureau of Mines investigated typical dust reduction efficiencies of wet bar cutter machines as they are presently being used in salt mines. Wet bar techniques have previously been used in coal mines, achieving dust reduction efficiencies ranging from 11 to 60 pct. Two different wet bar techniques, namely, the front spray and the water trickle, have been studied as they are currently being used in two salt mines. Preliminary results show that the dust reduction efficiencies have a large variation (0 to 66 pct), as is the case for wet bars used in coal. However, whereas wet bars in coal required 3 to 4 gpm water consumption, wet bars in salt obtained similar efficiencies with only 0.1 to 0.4 gpm. The most reliable data obtained during this study show that the front spray system consistently performs at efficiencies between 41 and 66 pct, with an average of 54 pct. The results indicate that, although wet bar cutter techniques in salt mines are a relatively simple and inexpensive means of dust control with a minimum of water consumption, further investigation should be performed to fully evaluate and optimize wet bar cutter dust reduction efficiencies.

Jan 1, 1980

By G. M. Ritcey, K. E. Haque, S. H. Lucas

"Laboratory-scale hydrochloric acid leach tests were conducted on an Elliot Lake uranium ore. Hydrochloric acid leaches without an oxidant or with molecular oxygen (i.e., air or pure oxygen gas) as an oxidant favoured uranium and radium extractions. Conditions for maximum uranium, thorium and radium extractions with hydrochloric acid in the presence of sodium chlorate were determined. The highest extractions of uranium (96%), thorium (81%) and radium (91%) were obtained using a mixture of 44.0 kg HCI and 2.5 kg NaCIOJ per tonne of ore at 75°C with 18 hours ' retention.Flowsheets for two-stage leaching are proposed. The residues obtained from the second-stage leach contain uranium (0.002%), thorium (0.006%) and radium (15 to 20 pCi/g). Tailings of this nature are considered suitable for mine backfill, and, if pyrite is removed, suitable for surfacedisposal.IntroductionThe nuclear energy industry forecasts an increasing demand for uranium. This increasing demand requires not only largescale mining and processing of conventional and complex uranium ores, but also leads to the consideration of new and nonconventional sources of uranium, e.g., black shales, phosphate rocks, granite, sea water and fossil-fuel ash.Sulphuric acid leaching is the most widely used process to extract uranium from the ore(l). The leach liquor is separated from the solids (tailings), purified, concentrated in various intermediate stages, and finally a semi-purified product, yellow cake (80-85070 U30 8) , is precipitated. The tailings, which constitute nearly 98% of the total bulk of most ores, are usually discarded in surface disposal areas.The Elliot Lake region of Ontario is one of the major uranium producing areas in Canada. The principal uranium minerals are brannerite and uraninite, present as microscopic grains in the matrix of quartz-pebble conglomerates. The average grade is between 0.10 and 0.15% UPs. Up to 6.5% pyrite is also present in the conglomerates. Because pyrite is less reactive toward sulphuric acid leaching, almost all the pyrite goes into the tailings and eventually into' the disposal sites."

Jan 1, 1980

By Ahmed M, Leung L

A program of microseismic noise monitor ing for gas outbursts, in conjunction with other mining engineering measurements and observations, is being undertaken at Leichhardt colliery in Queensland. Headings are developed at present by shotfiring. The equipment being used in this study includes piezoelectric accelerometer assemblies to detect microseismic noise which is then transmitted to a surface base station by cable. Data are recorded on an analogue magnetic tape recorder and are also analysed on-line using a commercially-available acoustic emission pulse analyser. It is proposed to re-interpret recorded data using various modes of analysis and to interface a desktop computer to the existing system to permit continuous monitoring on the mine site. No outbursts have been recorded or analysed and only a limited number of develop- ment shots, and the resultant microseismic activity, have been recorded to date.

Jan 1, 1980

By L. A. Roe

Calcium carbonate and talc fillers both find use in a multitude of Industries. Each filler has many commendable properties, and often compete for the same market. Quality controls for various grades are exacting and complicated. A detailed comparison of the physical and chemical properties of these two fillers is tabulated and the mining and processing of the ores is described.

Jan 1, 1980

By David B. McWhorter, John D. Nelson

INTRODUCTION The quantity of seepage that will be released from a tailings impoundment depends not only on the characteristics of the seepage control system, but also on the properties of the foundation soil or rock beneath the impoundment and the nature of the groundwater in the area. The interaction between various elements of the seepage control system and the influence the various characteristics of the site and impoundment have on seepage are the subject of this paper. The results of analyses are presented herein to indicate the nature and magnitude of the effect that the various factors will have on seep¬age losses. Analyses were conducted for a uranium mill tailings impoundment located in an area characteristic of many found in the western United States or Canada. A typical seepage control system consists of placement of either a clay or synthetic liner beneath the impoundment. In some cases an underdrain system may be placed on top of the liner to collect drainage from the tailings. The parameters that were varied in the analyses included those pertaining to the liner, underdrains and foundation strata. In general, it is shown that the seepage losses will vary in a complex manner depending on the interaction of the elements of the site and the seepage control system. As may be expected, the liner and underdrain systems have the most pronounced effect on controlling seepage. This paper deals with the quantity of seepage released from an impoundment However, the impact that seepage losses from an impoundment will have on the surrounding environment will depend on the rate at which contaminants will enter the groundwater and the nature of the groundwater flow itself. Consequently, when considering these results with regard to environmental impact they must be interpreted along with considerations of geochemical factors. MECHANICS OF SEEPAGE The mechanics of seepage and methods of analysis that were used will be discussed briefly herein. For a more detailed discussion the reader is referred elsewhere (McWhorter and Nelson, 1978, 1979, 1980). A general column through the impoundment was considered to be as shown in Fig. 1.

Jan 1, 1980

By M. J. Davie, D. S. Ross

"The successful design of a new mine water pumping system is in part dependent upon the accuracy with which the operating conditions can be forecast. This paper outlines the data which should be obtained on water quantity and quality. Methods of modifying the quality are also discussed. Some pumping systems for disposal of sludge are described, citing operating examples. The various types of mine dewatering pumps are described in terms of design characteristics as they affect operating efficiency and installation and maintenance costs. Piping system parameters are outlined. Finally, a hypothetical case study of pumping from a depth of 3,000 ft is assessed, with particular reference to capital costs.IntroductionMany mine operators would agree that the pumping system usually receives a low engineering priority during the design stage, and as a consequence causes some of the most frustrating problems during production. For a ""dry"" mine (up to 200 gpm), design of the pumping system may indeed be simple, but outside of the potash industry such mines are not common. For ""wet"" mines, the pumping system is important because it significantly affects the initial capital and on-going energy costs of the mine and, in the area of sludge disposal, the working conditions and production costs. Indeed, a failure in the pumping system usually has serious, and sometimes disastrous, consequences.The intent of this paper is to outline the factors which should be considered in the design of a pumping system and to describe the types of pumps used in mine dewatering and relate them to practical operating systems."

Jan 1, 1980

By J. C. Farge, G. G. Jacox

"The effect of composition and process variables on the properties of Marmet and modified Ni-Hard slugs will be discussed. The effect of shape on the over-all performance of grinding media and its relationship to the end product has been investigated and these results will be reviewed. The cost effectiveness of slugs versus balls has been well documented under various operating conditions and this will be presented in detail. IntroductionThe selection of grinding media is based on the cost-to-wear ratio combined with the consideration that it must stand repeated impacts without breaking. The specific consumption of grinding balls and slugs depend s primarily on their microstructure, which, in turn, is controlled by chemical composition and by the processing condition s to which they are subjected during manufacture.The first part of the paper deals with the optimization of alloy content to produce cast iron slugs with microstructures consisting essentially of marten site and carbide and with hardnesses of 650 B.H.N. and higher. The second part deals with the use of cast iron slugs to replace forged steel balls in milling operations. Tests indicate that the shape of the media has little if any effect on results and that the hardness and microstructure of grinding media will determine its relative performance. Where price is equal under similar milling conditions, the cost effectiveness of cast iron slugs is superior to that of forged steel balls.In order to understand the role of alloying elements in cast irons, it is judicious to consider the microstructural changes which occur during solidification and subsequent cooling, particularly from above the eutectoid temperature. Solidification starts with the formation and growth of dendrites of austenite. As temperature decreases, an eutectic nucleates and grows between the primary austenite dendrites. Immediately after solidification, the structure consists of proeutectic austenite and of the eutectic of primary carbides and austenite. On cooling to room temperature, austenite can be retained or transformed to pearlite, bainite, martensite or mixtures thereof. It is necessary to prevent decomposition of austenite into pearlite by adjusting the alloy content. For best abrasion resistance, the microstructure at room temperature should consist essentially of martensite and carbide. These types of irons are known as ""martensitic irons "". Depending on the carbon content of the austenite and cooling rate, "" as-cast"" martensitic irons will contain different proportions of martensite and retained austenite. The more carbon in solution in the austenite, the lower is the temperature at which the martensitic transfoemation takes place. By the time room temperature is reached ., the transformation is seldom complete, and the end product is generally a mixture of martensite and retained austenite."

Jan 1, 1980

By John Oskam

In 1873 Barton tines Corporation mining Garnets for Abrasives. From providing bulk Garnet Concentrate the technology has advanced to the sizing and classification of micron sized particles utilizing a Barton process. Processing of Garnet involves extensive quality control at all steps, first to insure product purity and secondly to insure the correct size range. Barton Mines produces about 30 different sizes of Garnet products to lead the world in the manufacture of technical abrasive Garnet. This paper will examine the present technology of Garnet Abrasive Manufacture and the specification to which the sizes are produced as well as some of the markets served.

Jan 1, 1980

By Charles H. Grant

Blast design methods generally deal with end points or limits of design such as spacing, burden, stemming depth, etc. Even cratering design deals with limits defined as a function of energy decay to a limit. Although this crater method provides a better method than trial and error judgment it does not take into consideration the distribution of energy throughout the material to be blasted. This paper deals with a method of examining this distribution with the aid of a computer and how changes in blast design affect this distribution. First I would like to explain the equation used to develop the energy summations throughout the blast. As shown in Figure I a series of drill holes are drilled to various depths starting by placing the explosive charge on the surface and then at various depths until a sufficient depth of hole is reached to exceed the ability of the explosive energy effect to reach the surface of the ground. All volumes of explosive are the same, all holes contain the same explosive and the drill hole diameter is the same.

Jan 1, 1980

By Fred C. Drury

The introduction and growth of modern chemical explosives based upon prilled ammonium nitrate has been the most significant development in the explosives industry during the 20th century. These modern chemical explosives have been of incalculable value to our society. Their use has permitted a reduction of blasting costs, improved safety, and the development of new resource sources which would not have been accessible without this new technology.

Jan 1, 1980

By A. B. Szwilski

"The various elements of longwall mine design are reviewed, particularly as they apply to condition s in the coalfields of the Plains region of Alberta. The following recommendations are made: (1) optimum panel lengths of 1000 to 2000 metres; (2) face lengths of 100 to 150 metres; (3) the use of retreat methods; (4) the restriction of floor undulations to less than 15 degrees. IntroductionThis article considers the elements of longwall mine design and is part of a short study that has been made of the feasibility of longwall mining in the Plains region, Alberta, Canada. The Plains region, with about 20 million tonnes, accounts for more than 80% of the coal resources of Alberta. The coalbearing strata in the Plains region cover an area of about 95,000 square miles. The geological formations dip very gently toward the southwest and, from a mining point of view, may be considered horizontal. The depth of the coal seams varies from several metres to over 650 metres. However, it is not anticipated that underground mining will be extended beyond the depth range of 25 to 250 metre s.The coal seams in the Plains region have been subject to many small mining operations in the past. The majority of these small mines were limited to a depth of about 50 metres, working mainly by room-and-pillar methods, although hand-filled longwall mining was often used.The development of new underground mining operations in the Plains region will have to be on a 'start-from-scratch' basis, especially regarding the installation of equipment. Longwall mining is more mechanized than any other method of mining and requires careful attention for the selection of new and expensive equipment. There have been many proven longwall advance and retreat systems in Europe and North America; mining conditions in the Plains region are more similar to those in the United States. Therefore, it will be essential for new mining pro jects in the Plains region to commence with proven system s and equipment; in time, perhaps an experimentation process could be attempted as experience is gained.Generally, the coal face is the key factor in mine productivity, which depends a great deal on equipment reliability, training and experience of the operators. The original design of coal faces must be flexible enough to cater for potential improvements so that running time can be increased."

Jan 1, 1980

By R. L. Sandefur

Professor Kim's excellent review article1 on ultimate pit planning contains a statement of the apparently widely held but incorrect belief that "kriging provides information on the confidence limits around the estimate which no other extension technique is capable of supplying." If a geostatistical approach is valid, there are several good reasons for using kriging but uniquely provided confidence limits is not among them. If kriging is possible, then confidence limits can be calculated for any other linear estimate. Kriging is the procedure which finds the weighing coefficients which minimize the estimation variance [ ] is the variance of blocks like the one being estimated. wi is the covariance of the estimated block and the i-th sample. oij is the covariance of the i-th sample and the j-th sample. Ai is the weighing coefficient for the i-th sample. N is the number of samples. The formula for estimation variance can also be used to calculate confidence limits on blocks estimated by any linear combination of sample grades including: 1) Polygons a. Hole nearest block centroid is assigned weight 1. All other holes are assigned weight 0. b. Polygonal area weighing. The samples are assigned weights directly proportional to their polygonal areas of influence within the block. The weights sum to 1. 2) Inverse distance weighing. The samples are assigned weights directly proportional to the reciprocal of their distance to some power from the block centriod. The weights sum to 1. Often only holes nearer than a certain distance and/or the nearest hole in each octant is considered. If there is an antisotropy to the ore body, an elliptical transformation often gives more accurate results. The most popular inverse distance weighing function is inverse squared distances (IDS). 3) Simple average. All samples within a certain distance are assigned the same weights which sum to 1. As an example of the applicability of the above formula to any linear estimate an internal verification on copper grade of 665 blast holes on the 1040 bench at Utah's Island Copper mine is presented. Internal verification is simple and applicable to non-linear estimates as well. Any sample (drill hole, bulk, trench, or chip) is dropped out, the value of the dropped sample estimated and compared with the actual value. If this is done for all samples, a measure of confidence limits is obtained. Internal verification is used in Cominco's MEPS system4 and in the BLUEPACK system.5 Comparison of block values against estimates697 is not dissimilar to internal verification. Results of the internal verification are presented below:

Jan 1, 1980