Search Documents

By K. Verghese, R. W. Rousseau, R. P. Gardner

A radioactive tracer method and a size-discretized, mass balance model are formulated and demonstrated in a feasibility experiment for the determination of crystal growth rates in MSMPR crystallizers. The system studied is aqueous KN03 with K-42 as the radioactive tracer. The results indicate that the method should prove to be very valuable for this application, particularly when systems exhibiting size-dependent growth rates are of interest. An indicated refinement to the tracer method is the simultaneous use of an additional tracer in the liquid to determine the amount of radioactivity from the liquid that is adsorbed on the samples of filtered crystals.

Jan 1, 1980

By P. R. Jochens

South Africa depends to a considerable measure on the exploitation of mineral reserves and the processing of these minerals. One of the prime requirements for the mining and metallurgical industry to continue in this vital role is access to sufficient energy in a suitable form. Hence, four important questions are discussed: Does South Africa have sufficient energy for the processing of its minerals and metals! Will the cost of energy allow South Africa's minerals and metals to compete on world markets? Can mining and metallurgical processes become more energy-efficiency Can mining and metallurgical processes be adapted to the various forms of energy that may have to be utilized in the future? It is concluded that about 26 per cent of the extractable reserves of coal would be required in the mining and processing of 50 per cent of South Africa's reserves of gold, platinum-group metals, copper, iron, ferrochromium, and ferromanganese. However, the reducing agents required exceed the extractable reserves but not the total estimates of mineable in situ resources of metallurgical coal and anthracitic coal. Even under the severe constraint that coal could become virtually the sole source of energy, only about three-quarters of the extractable reserves of coal would have been consumed by the year 2025. The reasonably assured resources of uranium metal that can be recovered at less than $80 per kilogram are considerable and, at current conversion efficiencies to electricity, are equivalent to one-fifth of the extractable reserves of coal. The rate of exportation of energy in the form of U30. was about five times that of coal in 1978. It is pointed out that the price of energy has a direct effect on the competitiveness of metals, and, although constituting only a small proportion of the selling price of precious metals, it represents a significant proportion of the selling price of copper and metals recovered from oxide ores. The scope for the conservation of energy appears to be greater in the extraction and conversion of primary energy-carriers to electrical energy than in other mining or metallurgical fields. Provided that alternative sources of energy can be converted to electrical energy, they can be applied to the mining and metallurgical industries. The decision as to which type of energy should be used in specific mining and metallurgical situations is complicated, and is likely to be subjected to closer scrutiny than in the past. The hope is expressed that the tentative conclusions reached will give rise to more-quantitative analyses from those qualified to undertake such an exercise. Inevitably, the questions asked at the outset give rise to more questions, and the more interesting ones are posed in the context of each conclusion.

Jan 1, 1980

By C. B. Foster, S. I. Freedman, E. M. Jamgochian

Coal-oil mixture (COM) combustion technology is regarded by the US Department of Energy (DOE) as near term and Potentially applicable to existing utility and industrial steam generators and for injection into blast furnaces. From work done previously, it has been established that COM can be burned in existing boilers and blast furnaces. Therefore, the issues being addressed by the current DOE program are: (1) determination of best available technology to achieve environmentally acceptable long-term reliable operation and (2) determination of applications for which COM can be utilized economically. Some of the technological options have begun to be determined by projects already under way. However, many projects are still in the early stages of development.

Jan 1, 1980

By Fukui M

An increase in pig iron output by 50 per cent was aimed at after re-lining No.2 blast furnace of NAKAYAMA STEEL WORKS. This had to be achieved by increasing both the furnace volume (from 673 to 757 m3) and its productivity, Without equipment for high top pressure operation, high productivity was mainly attained by the following three measures; (1) improving the gas flow characteristics by maintaining a high ratio of agglomerated ores, increasing the strength of sinter and coke, and optimizing the charge distribution, (2) decreasing the fuel ratio by low Si operation and the use of hot blast, and (3) oxygen enrichment. In addition, the tapping controls for pig iron and slag were intensified. As a result of the above measures an excellent hot metal output of 2.7 tonne/m3/day was attained in April 1979 (monthly average).

Jan 1, 1980

By M. M. Jones

A procedure for the spectrophotometric determination of uranium has been developed in support of minerals research being conducted by the Bureau of Mines. Uranium is separated from the sample by tributylphosphate extraction from acid solution containing added aluminum nitrate and (ethylene dinitrilo)-tetraacetic acid solutions. The colored uranium-dibenzoy1methane complex is developed in the organic phase by adding an ethanol solution of dibenzoylmethane buffered with triethanolamine. Absorbance is measured at 410 nanometers, and the response is linear up to at least 100 micrograms U30S in the aqueous aliquot taken for analysis. Aliquots containing as little as 8 micrograms U30S may be analyzed with relative errors no greater than ±5 percent. For aliquots containing at least 35 micrograms U308, relative standard deviation at the 95-percent confidence level is about ±2.2 percent. Appropriate procedures are given for analyzing a wide variety of samples.

Jan 1, 1980

By M. A. A. de Klaver

Functional Description Figure 1 is a typical flowsheet for a system for solid fuel addition to filter cake. Solid fuel, coal, coal breeze, or charcoal, is fed from a,stockpile to a surge hopper. The solid fuel is metered into a grinding mill. The fuel is dried and ground in a grinding mill. The on-size particles are removed from the mill by air sweeping. The ground solid fuel is separated from the air stream by a cyclone and stored in a surge hopper. The ground solid fuel is then pneumatically conveyed to a small hopper in the balling area. The fuel is proportioned into the filter cake just prior to mixing. An efficient mixer is very important to have a successful operation. The exact flowsheet would depend on a number of factors including what fuel is used, how the fuel is received, and the cnaracteristics of the fuel as received. Availability of floor space in the plant may also affect the flowsheet. For example, drying air may be supplied from the pellet furnace if the grinding mill can be located near the grate, or the pneumatic conveying system and a surge hopper may be eliminated by placing the grinding mill adjacent .to the mixing area. Also, for a multiple line plant, a ball mill rather than a roller mill may be more suitable.

Jan 1, 1980

By R W. Bellenie, P N. Blakey

The phenomena of post detonation gases in muckpiles is reasonably well known. It causes the 'rumbling' noises occasionally heard after a blast in open pits or quarries and is thought to occur due to initiation of carbon monoxide, hydrogen, etc. by 'hot' spots within the muckpile. The problem usually occurs with highly aluminized products, but can occur with any oxygen deficient product. This phenomenon was never a problem underground due to restriction on access to blast areas, ventilation criteria, etc. until the advent of large diameter blastholes and particularly their use for specialized applications such as drilling for blasting down 'hang-ups' in ore passes.

Jan 1, 1980

By Yoginder P. Chugh

Effects of moisture absorption on the behavior of the Dykersburg shale overlying Harrisburg coal seam in Southern Illinois are presented in this paper. Cylindrical samples of the shale 2.5 cm in diameter and 5.0 cm long were studied for weight gain and swelling strains at 90, 95, and 100 percent relative humidity and under immersed water conditions. After attaining equilibrium conditions, the samples were studied for changes in the strength and deformation behavior. The depth of moisture penetration was measured using the Vickers microhardness measurements. Using the basic mass transfer concepts, effective diffusion coefficients were computed for the shale.

Jan 1, 1980

By H. Sato, R. J. Lipp, I. Iwasaki, K. A. Smith

Selective desliming holds much promise for upgrading low-grade, finely disseminated iron ores that are not readily amenable to conventional flotation. The process is extremely sensitive to the presence of calcium and magnesium ions that are in process water or are released by constituent minerals. The effects of these two alkaline earth ions on quartz were compared through streaming potential measurements, flocculation and cationic flotation tests, abstraction tests and scanning electron microscope studies. Calcium ion, adsorbed as CaOH+, and magnesium ion, attached by heterocoagulation as Mg(OH)2 precipitate, were responsible for the flocculation of quartz suspension and for the depression in cationic flotation of silica in alkaline pulp solutions. Magnesium hydroxide coating could be removed, similarly to adsorbed calcium ion, by complexation with EDTA and polyphosphates.

Jan 1, 1980

By Corale Brierley

The effect of hydrogen peroxide (H202) on growth and respiration of Thiobacillus thiooxidans and Thiobacillus ferrooxidans, organisms involved in acid leaching of copper sulfide minerals and uarnium oxides, was examined. Oxygen uptake and growth by T. thiooxidans were totally inhibited after contact with 0.82 mM H202. Complete inhibition of oxygen uptake by T. ferrooxidans occurred at 8.75 mM H202, and growth was inhibited after 6 hr exposure to 2.06 mM H202. Higher concentration of H202 can be used without detriment to thiobacilli if it is dissipated prior to reaching the oxidation pond or dump surface.

Jan 1, 1980

By D. Buranek, J. G. Wulff, F. W. Gifford

I. INTRODUCTION During the past few years, the state of the art of disposal of solid and liquid waste products from uranium mining and milling operations has experienced some rather interesting and significant changes. Some of these changes have resulted from technological advances in the milling operations and in the engineering aspects of the actual design and construction of the disposal facilities. However, the most significant changes, at least those which have had the greatest impact on the comparative cost and economics of modern disposal systems, have been environmental requirements and regulatory controls, which have become increasingly stringent in recent years. Without delving into the details of the myriad of new laws and regulations which now control the uranium industry, it can be stated with reasonable confidence that one of the principal purposes of more rigid state and federal controls over this industry is the basic desire to promote safer, more reliable and longer term means of effectively controlling and disposing of the potentially objectionable waste products resulting from uranium mining and milling operations. It is difficult to take issue with these basic goals because their need was spawned by past lack of awareness and inattention on the parts of both government and industry to the long term environmental problems and potentially hazardous conditions which can be created by limited planning and ill-conceived or poorly controlled and executed disposal practices. On the other hand, despite the good intentions of those who developed and those who are administering the regulatory controls now in effect, the basic danger exists that overgeneralization of the approach to disposal problems and overrestriction of the potentially acceptable solutions for uranium mine and mill waste disposal could have a significant, adverse economic impact on the mining industry and the ultimate consumers of their products. The regulatory pendulum, which perhaps swung too far toward lack of controls over uranium mill waste disposal in the 1940's, could now well be headed too far in the opposite direction, that is toward over-regulation in the form of restrictions based on technically unrealistic or weakly supportable

Jan 1, 1980

By LeRoy R. Curwick

This Bureau of Mines report presents the results of a study conducted to assess the domestic availability of chromium from superalloy and cast heat- and corrosion-resistant alloy scrap material. Six alloy classes included in this survey were investment cast, hardfacing, and wrought nickel- and cobalt-base alloys, wrought nickel-iron-base alloys, and heat- and corrosion-resistant alloy castings. Data were collected for 1976 on metallic scrap generation, use patterns, and production practices for these alloy producing and using industries. A model was developed that allowed an assessment of the materials flow circuits within the industries that produce these alloys. The types, amounts, sources, secondary products, and ultimate destinations of chromium- containing metallic scrap for the six alloy classes were determined. Regarding the overall recycling efficiency of these alloy producing and using industries, of the 580.9 million pounds of scrap generated from these six alloy classes in 1976, about 72 percent (416.8 million pounds) was remelted by the same alloy-producing industries, about 18 percent (104.9 million pounds) was downgraded into stainless and low-alloy steels, about 3 percent (19.7 million pounds) was exported, and about 7 percent (39.5 million pounds) was lost through landfill or other disposal or service wastage. The lost material is primarily contaminated oxides for which recovery is currently uneconomic. However, the 124.6 million pounds of scrap material downgraded or exported in 197b contained potentially recoverable critical strategic elements. The amount of scrap material lost to the six alloy-producing industries in this manner contained 22.1 million pounds of chromium, 53.4 million pounds of nickel, 5.9 million pounds of cobalt, 35.9 million pounds of iron, and 7.3 million pounds of other alloying elements.

Jan 1, 1980

By P. J. van der Walt, P. J. F. Fourie, L. M. Falcon

Various methods for the beneficiation of minus 0,5 mm coal are examined briefly, and tests are described on a cyclone of 150 mm diameter operating with magnetite as the medium. It was found that, for sharp separations, at least 50 per cent of the magnetite should be finer than 1Oµm. At that size, the ash content of the product was about 7 per cent at yields of 59 to 64 per cent, and the loss of medium was reasonable (about I kg per ton of fines treated).

Jan 1, 1980

By Mr. Peter J. Huck

Recent research has developed procedural control and geophysical test methods that can greatly enhance quality control in rock grouting. Confidence that design objectives will be made In construction requires that grout monitoring efforts be carefully designed and integrated into the overall project. Parameters that should be monitored are identified and documentation/review procedures that permit effective evaluation of the grouting effort are discussed.

Jan 1, 1980

By Donald P. Richards

The use of point load test data by the authors to estimate rock mass cohesion is a very ingenious approach. It must be emphasized that this estimate is indeed only an estimate since the point load strength index employed to predict the uniaxial compressive strength (and subsequently predict the cohesion) is likewise only an estimate.

Jan 1, 1980

By W. N. Marchant

[The citrate process for flue gas desulfurization (FGD) is a product of continuing research by the U.S. Bureau of Mines to meet the goal of minimizing the objectionable effects of minerals industry operations upon the environment. The reduction of SO2, in solution by H2S to produce elemental sulfur by the citrate process is extremely complex and results in solutions that contain at least nine different sulfur species. Process solution analysis is essential to a clear understanding of process chemistry and its safe, efficient operation. The various, chemical species, the approximate ranges of their concentrations in citrate process solutions, and the analytical methods evolved to determine them are hydrogen sulfide (~0M to 0.06M) by specific ion electrode, polysulfides (unknown) by ultraviolet (UV) spectrophotometry, elemental sulfur (~0M to -0.001M dissolved, ~0M to ~0.1M suspended) by W spectrophotometry, thiosulfatc (~0M to ~0.25M) by iodometry or high performance liquid chromatography (HPLC), polythionates (~0M to ~0.01M) by thin layer chrornatogrphy (TLC), dithionite (searched for but~ not detected in process solutions) by polarography or TLC, bisulfite (~0M to 0.2M) by iodometry, sulfate (~0M to 1M) by a Bureau-developed gravimetric procedure, citric acid (-GM to 0.5M) by titration or visible colorimetry, glycolic acid (~0M to 1N) by HPLC, sodium (~1.5M) by flame photo¬metry, and chloride by argentometric titration.]

Jan 1, 1980

By E. G. Joe

Introduction Uranium mining has been actively carried on in Canada for over twenty-five years mainly in Ontario at Elliot Lake in Bancroft, and in Northern Saskatchewan at the operations of Eldorado Nuclear Ltd. During this period, approximately one hundred million tons of mill tailings have been created and lie mainly on the surface close to the mining and milling installations. If all of the present reserves of uranium ores in Canada are mined, a further eight hundred million tons of mine tailings could be created in Ontario, Saskatchewan, the Northwest Territories, Labrador and British Columbia. The present control of effluents from existing tailings is managed by the operating mines under the regulations of both federal and provincial control agencies. It is the long-term effect of these tailings on the environment that has not been clearly defined or measured. Several years ago, the Canada Centre for Mineral and Energy Technology of the Department of Energy, Mines and Resources, embarked upon a program of research directed at the long-term effects of uranium mine tailings. Much of the research to date has been on tailings in the Elliot Lake, Ontario area where some tailings piles have existed for over twenty years. The program consists of two projects, one to address the problem of existing tailings and the other to examine alternatives in the management of current and future tailings. TAILINGS CHARACTERISTICS Uranium tailings are generally the result of sulphuric acid leaching in which the uranium and alkaline minerals such as carbonates and chlorites are leached out. If the ore contains sulphides, these minerals potentially present an additional hazard of acid generation over time and could increase the mobility of heavy metals and some radionuclides such as thorium-230. Except for the extracted uranium, most of the radionuclides from the ore remain in the tailings pile. Uranium ores in Canada span a wide variety of mineralization and associated gangue composition. Uranium minerals include pitchblende, uraninite, uranothorite, brannerite and the phosphate uranium minerals autunite and saleeite. Gangue minerals vary from acid consuming carbonates, and chlorites to acid producing sulphides and inert silicates. With such a wide variety in ore composition, the characteristics of the resultant tailings in Canada are in many cases site specific and the solutions to the long-term effects of these tailings may also be site specific.

Jan 1, 1980

By Firmin K

The Mt. Tom Price orebody of Hamersley Iron Pty. Limited consists of a folded hematite - shale sequence capped by a layer of goethite. Consequently, variations in iron content occur within the orebody, and as the overall grade is below that required to make specification products, selective mining must be carried out. A necessary preliminary to quality control'of products based on selective mining is the production of advance data, on the tonnages and grades of material to be expected in future mining areas. Bench plans showing zones of different grades and types of material anticipated are prepared from structural geological information. The grades of materials on a bench are essentially governed by the positions and attitudes of the shale bands. Quality control is exercised by blending different grades and types of material in primary crusher feed. Iron grade is the prime grade consideration although sometimes the level of phosphorus content must be considered. Pre-production grades Are determined from assay of samples taken from blasthole cuttings.

Jan 1, 1980

By Geo. A. Wells

Abstract The consumption of barytes in certain paints polyurethane foams, seamless, flooring, glass, brake linings, plastisol caskets for food containers and in fluids used for gastrointestinal X-ray examinations rely on tie unique properties of barium sulfate, There are no readily available mineral substitutes. Barytes are also the essential raw material for the manufacture of industrially important barium chemicals. High quality barite ore has become scarce throughout the world. Processing ore into quality end products is both capital and energy intensive. These factors have tended to limit availability and increase prices which have encouraged the use of alternates and restricted market growth.

Jan 1, 1980

By J. Stachulak

This paper deals with theoretical considerations and practical applications of ventilation network calculations, based on mass flow rates and performed by computer simulation in our deepest operating mine - Creighton. The paper also deals with natural ventilation. In the usually accepted air-flow theory, the air is assumed to behave like an incompresssible medium. This introduces considerable error where temperature and pressure changes are great. Therefore, any study of the air flow in deep mines, must take into account compressibility. Basing ventilation calculations on mass flow allows a distinction to be made between air leakage and such quantity changes which occur due to air density changes. The energy which is required to convey one pound of air through a mine can be obtained by adding all head losses hL (ft-lb) of the ventilation paths through which the air flows. However, this total energy will not be correctly expressed in a compressible fluid by summing all pressure losses PL = hL x d (ft-lb/ft3 = lb/ft2) d = density. There is a law of mass conservation, but no law of volume conservation. Natural ventilation is caused by the conversion of heat into mechanical energy and not by the difference in upcast and downcast densities, as often believed. In an existing mine natural ventilation can be determined correctly by plotting a pressure volume diagram and measuring the area ? [ ] vdP = hN, where v = specific volume, or by measuring the sum of all friction losses and work provided by a fan. These procedures are tedious. The natural ventilation head (hN) can be approximated by the equaticn hN =[ ] tdZ. Where T is the average absolute temperature, t air temperature and Z elevation. In Prof. R. Greuer's computer program this determination of hN is automatically done for every mesh of the network.

Jan 1, 1980