Search Documents

By D. M. Thayer

Dry magnetic separation of feebly magnetic minerals and wet magnetic separators suitable for highly magnetic minerals have been commercially utilized for a number of years. The beneficiation of magnetic taconite ores by conventional, low intensity magnetic separators in combination with flotation is well established technology (1). However, over the past decade much effort has been expended in developing techniques for the upgrading of feebly magnetic oxidized iron ores (2,5). Such research and development have been stimulated by the limitations of the above-mentioned techniques in application to ores containing fine material; for example, ores requiring fine grinding for liberation or slime-forming ores such as the oxidized taconites or semi-taconites. Wet separation has allowed the reduction of the minim particle size that can be effectively treated from that allowable for high intensity dry magnetic separation. Consequently, the development of high intensity wet magnetic separation methods has received much attention in the search for an effective method to treat the weakly magnetic minerals. Recently Lawver and Hopstock (5) have provided an excellent review of the state of know- ledge of this technology. In addition, a valuable compendium of available laboratory and commercial devices is included. Nonetheless, the feasibility of the use of high intensity magnetic separation in a particular application is largly empirical in nature and requires experimentation to chazacterize the response of a particular ore. The purpose of this paper is to assess the incorporation of high intensity magnetic separation for the beneficiation of a non- sliming specular Michigan hematite. Particular attention is focused on the existence of a lower limit of particle size that can be treated effectively and is inherent in the use of these techniques. Additionally, a rationalization of various models presented in the literature is attempted.

Jan 1, 1979

By L. W. Hamel

"Two 35 foot diameter enviro clear thickeners were tested in series as CCD units from June until October, 1978. Up to shutdown in July, we ran with automatic bed level control via the level probes and underflow pinch valves. Despite extensive efforts, we were unable to eliminate the surges created between the units by the opening and closing of the pinch valves. Early in July, the best rake speed and gap setting were determined. After shutdown, the enviro clears were run by manually controlling the pinch valves. These efforts were successful.A few mechanical problems were encountered while operating the thickeners. New units should incorporate more support for the drive coupling and a rubber feed seal. A few modifications of the instrumentation control scheme will be required before the units can be fully automated. A less sophisticated automatic flocculant addition system will accomplish the desired results. Control of the underflow withdrawal via the pinch valve should be investigated further. Our best results were obtained by keeping the feed volume to the No. 1 enviro clear constant. Surges were controlled by opening or closing both underflow valves proportionately.Capacity of the enviro clears is dependent of many variables. The ore treated during the test program was much finer than that reported on in R & D Project Report 76-02. Conditions were never steady enough to determine best flocculant dosage or addition point(s). The lowest soluble losses were obtained at very high wash rates. The underflow densities drop but the soluble losses also drop. Regression equations were developed in order to assess the effect of the various parameters. Within the range studied, these equations will predict the performance of enviro clear thickeners as CCD units on Elliot Lake ores. Our results show that the enviro clear thickeners are a viable alternative to the conventional CCD thickener."

Jan 1, 1979

"Status of the Mineral Industries" provides a written and graphic view of the Nation's mineral position and its mineral industries. The report, issued annually by the Bureau of Mines, U.S. Department of the Interior, describes recent activities in mineral production, consumption, imports, exports, and uses of significant minerals and mineral raw materials. Charts profile trends for the past 28 years in supplies and uses of iron, steel, major nonferrous metals, primary nonmetallic construction raw materials, fertilizers, and plastics. Also included are current and historical financial data on the mineral industries, such as debt-equity ratios, asset-to-liability ratios, and plant and equipment expenditures.

Jan 1, 1979

By H. O. McDonald

The Bureau of Mines reviewed the chemical vapor deposition (CVD) literature of the group IVB, VB, and VIR elements. This review was utilized in the Bureau's research to provide erosion-, abrasion-, and corrosion-resistant coatings for valve components used in coal gasification units. This report attempts to bring together the many CVD references that have been published since 1966. Each of the group IVB, VB, and VLB metal coatings were reviewed, and some of their preparation methods, uses, and properties are given. A total of 160 references were found for the nine elements. Isotope separation, stronger steels, solar absorbers, alloys, superconductors, optical fibers, and coatings to increase the life of materials are some of the new uses for CVD.

Jan 1, 1979

By Raymond H. Young, Paul Sennett

INTRODUCTION Kaolin clay, consisting largely of the mineral kaolinite, is widely used as a white pigment. In the United States, for instance, pigment kaolin production was nearly 6,000,000 tons in 1976 (1). Production for this year should be significantly above this level. Current prices for kaolinite 'pigments range from about $20.00/ ton to$260.00/tony,depending on the amount of processing needed to make the final product. Although much of this pigment kaolinite is used as an inert filler where product specifications are not very rigid, a large quantity of kaolinite is converted to products where very restrictive specifications exist. These specifications set severe limits on such properties as viscosity in a water suspension, particle size distribution, color, and brightness. This discussion will concentrate on methods available to improve the color and brightness of pigment kaolin and will review the advantages and problems associated with these various methods. The term "brightness" refers to the reflectance of the pigment to blue light (2). Since even the brightest commercial kaolins have a somewhat yellowish color, the blue reflectance (or brightness) is a reasonably good measure of their nearness to a perfectly white material. I KAOLINITE STRUCTURE AND SOURCES The mineral kaolinite is an aluminum silicate and can be represented by the formula (OH) 8Si4A14010. The formula is frequently written

Jan 1, 1979

By W C. Burkle

A rather common observation over the last several decades at least has been that rock or ore properties influence blasting results more than does the explosive type that has been used in the blast. It we accept that premise than it is held here that the material to be blasted should receive even closer attention as to its properties. Several years ago, Dr. Richard Ash published papers that pointed out the rock properties that mostly influence blasting. These principles are given attention in this paper. We have gone somewhat further - or lets say expanded this subject in regard to the role of rock structure in open pit blasting. Though open pit work is given some prominence, we believe that much can be observed and applied to underground mining.

Jan 1, 1979

By James H. Cobbs

Blind boring of shafts is becoming an increasingly important part of shaft sinking. Blind-bored shafts have reached diameters of 25 It in Europe and 16-1/2 ft in the United States. Much of the technology developed for blind boring has evolved from the technology of drilling wells for oil and gas production. Blind boring offers economic advantage in a number of situations where conventional shaft sinking either is extremely difficult or very expensive by virtue of large-capacity aquifers which must be penetrated, unstable ground or where very rapid sinking is required. In sedimentary rocks, blind boring is cost competitive with conventional sinking, in diameters of about 12 ft or less. Blind boring is not competitive with raise boring where conditions are favourable for raise boring. Blind boring does, however, offer greater flexibility than raise boring and can be performed in situations where raise boring is inefficient or impossible. Combination machinery has been developed to perform both blind boring and raise boring, so that the machine can be used effectively in situations where only the near-surface portions of the shaft are unfavourable for raise boring. Development work is being supported by the United States Bureau of Mines for blind boring equipment capable of boring shafts up to 30 feet in diameter.

Jan 1, 1979

By Kenneth K. Humphreys

INTRODUCTION What is automation? Why automate? Webster's New Collegiate Dictionary defines automation as "the automatically controlled operation of an apparatus, process, or system by mechanical or electronic devices that take the place of human organs of observation, effort, and decision." This definition gives an implied answer to the second question, "Why automate?" Automation, automatic control devices, and process control equipment receive their justification in supplementing or replacing manpower, which results in decreased operating costs. In the past, processes were operated with the minimum amount of instruments needed merely to guide operators. Processes were manually con- trolled by the operator on the basis of simple temperature, pressure, flow, and level indications on a panel. Today the tendency is to design a new plant to operate in a fully automatic manner according to a preset pro- gram utilizing a minimum of manpower. In addition to this direct cost reduction in manual labor, increased equipment capacity results from uniformity of flow and uniform control of process variables. This control eliminates or minimizes surges and permits equipment to be operated at or near its ultimate capacity and, for a given material throughput, permits the use of smaller process equipment. Automatic control, therefore, be it in the field of coal processing or in any industrial field, is simply a problem of economics. Control equipment is justified in terms of its contribution toward increasing productivity, increasing profit margins, or producing a new and salable product at a profit. Instruments and control devices can be divided into two general groups: (1) units which measure and (2) units which both measure and control a process variable.

Jan 1, 1979

By Charles E. Joachim

Current Army tunnel destruction criteria (1) are based on limited nuclear-explosive (NE) and high-explosive (HE) test data. The PILE DRIVER (2) and HARDHAT (3) events investigated tunnel and support system response where yields were relatively large and tunnel diameter small compared to typical underground openings and localized stress fields of low yield weapons. Some limited tunnel destruction information was obtained from underground events of the PLUMBBOB and HARDTACK II Series (4). These events used access drifts which were designed to be self closing at the weapon point. The limited NE data are augmented by HE results from the Underground Explosion Test (UET) Program, a series of model and prototype-scale experiments in granite and sandstone (5). Weapon standoff distances (charge c.g. to tunnel wall) were at or near the maximum for major damage. Limited tunnel destruction was produced by a series of hasty and deliberate tests (6) on abandoned railroad tunnels in basalt. Additional HE data were obtained from model tests at the Waterways Experiment Station (WES) (7) using 2.1 MJ (2 lb) TNT charges and tunnel diameters varying from 3 to 17 cm (1.2 to 6.6 in). Recent laboratory scale HE experiments (8) conducted at the WES under the ESSEX program investigated the effects of tunnel diameter, standoff distance, charge confinement, material strength and to a limited extent, tunnel spacing and liner strength variations on tunnel damage. This paper summarizes the analysis conducted to develop predictions for the effects of low-yield nuclear weapons against tunnels and underground openings in rock.

Jan 1, 1979

By John C. Edwards

The Bureau of Mines has developed a time-dependent mathematical model of radiative heating of bulkheads in mines. The model includes both reradiation from the duct (cylindrical) walls and direct radiation from the fire zone. Thermal loss into the wall of the duct and into the bulkhead is included. Both brick and wood bulkheads are considered. It is found that the heating rate of the system scales as the duct length-to-diameter ratio and the flame temperature. In particular, the time required for the irradiated surface of the bulkhead to reach a specified temperature decreases with increasing flame temperature for a fixed length-to-diameter ratio and increases with increasing length-to-diameter ratio for a specified flame temperature. It is also deter-mined that the time, T, for the bulkhead surface temperature to reach a specific value, Tb, for a fixed length-to-diameter ratio less than 4 and for a flame temperature of 1,200 K is approximately linearly dependent on Tb for 500 K < Tb < 700 K, and is nearly exponentially dependent on the length-to-diameter ratio for Tb = 600 and 700 K.

Jan 1, 1979

By Arthur E. Lord, W. Martin McCabe, Robert M. Koerner

Following the driving of each new section of tunnel, a prompt decision is required regarding the type and extent of primary support to control convergence and prevent ground failure. Sometime thereafter, the effectiveness of the in-place support must be evaluated over the entire length of excavation. It is therefore extremely desirable to have available a lightweight, portable, easy to install and interpret, cost effective monitoring system to assist with these ground control functions. Such a system can be assembled based on the acoustic emission (or microseismic) technique. This monitoring technique uses a piezoelectric transducer to detect subaudible noises associated with deformation of and/or crack propagation in the soil or rock being monitored. After detection, the signals are then amplified, filtered and electronically counted to provide a quantified assessment of the stability of the structure. In the simplest sense, the absence of emission, or counts, signifies no deformation and thus stability. Conversely, the occurrance of counts signifies instability to varying degrees. The higher the count rate, the greater the instability and the need for immediate or additional support. Described in this paper is an overview of the acoustic emission (microseismic) method, details of its use in a laboratory study measuring convergence and stand-up time in soil, and the behavior of rock samples under similar stress conditions. Field use of the method is recommended for ground control monitoring in tunnels, and some suggestions regarding monitoring procedure are presented.

Jan 1, 1979

By John T. Crawford

Various open pit limit-analysis techniques have been utilized for many years to design pit limit surfaces. In the last 15 years there have been many advances in developing sophisticated computer methods to aid this process. The extensive capability of the digital computer has led to effective utilization of multiple alternative approaches to problem solving. Computerized open pit limit analysis methods can be applied to a broad scope of long range and intermediate range mine planning and design needs. This paper provides an overview of some of the more important of these applications. While not covered in detail, they are meant to indicate the flexibility and adaptability of open pit limit analysis methods and to stimulate thought.

Jan 1, 1979

By M. B. Myers

The subject matter of this paper will be discussed under three main headings. 1.-Fire-Resistant Fluids: (a) the need for such materials, based on historical events; (b) a definition of fire -resistant fluids; (c) general description, characteristics, operational parameters, advantages and disadvantages of oil-in-water emulsions (HFB), water-polymer fluids (HFC) and anhydrous or synthetic fluids (HFD). 2.-A review of equipment associated with the use of fire-resistant hydraulic fluids; (a) performance testing of hydraulic equipment, i.e. gear pumps, vane pumps, axial and radial piston pumps, hydraulic motors, etc., pressure, speed, filtration limitations, etc., and effects on valves, elastomers, paints, etc.; (b) hydraulic system design features and selection of suitable units; (c) types of mining applications currently employing fire-resistant fluids. 3.-Test methods used to evaluate fire-resistant fluids: (a) fire testing methods, i.e. wick tests, spray ignition testing, hot manifold tests, factory mutual tests, all to establish fire-resistancy parameters and acceptance; (b) new developments in fire-resistancy evaluation; (c) the examination of other performance tests, e.g., effects of evaporation, sliding wear, life of rolling element bearings, etc.

Jan 1, 1979

The concept of "profit" is implicit in the definition of an ore reserve. It is suggested that the flexible concept "economic" is more appropriate. This allows different economic considerations to be taken to account when determining what is ore at the feasibility study stage; during actual mining production; before mine closure; and from the viewpoint of the national economy. Economic factors which are highly variable, and largely beyond a mining enterprise&apos;s control, affect the economic exploitation of a mineral resource. Major economic factors include: metal prices; operating costs; the cost of original and replacement capital equipment; the cost of capital; taxation and royalties; inflation; exchange rates and the state of the world economy. The paper suggests why a careful quantification of the average value, trend, and variation from the trend of major economic factors should be made and how this will lead to a better definition of ore reserves. The paper also discusses the necessity of reappraising economic factors during the life of a mine in order to maximise the economic surplus and to minimise the wastage of natural, economic and human resources employed in mining.

Jan 1, 1979

By D. M. Doyle

A study of the various components contributing to energy costs and their relationships to generally trended operating data, such as tonnage, operating costs, etc., over progressively shorter time periods provides information for an energy audit. A study of annual data gives some insight into the importance of various energy components. As the time frame of the study progresses through monthly, daily and, finally, into quarter hourly data, the variations become more evident and, most important, strategies develop to minimize energy costs. The results of an audit conducted during the summer of 1978 at Wesfrob Mines Limited are reported to illustrate this important phase, prerequisite to a meaningful energy cost avoidance program. The balance of the paper deals with the energy conservation program at Falconbridge Nickel Mines Limited&apos;s Sudbury operations, the metering and control equipment, the commitment, the new energy accounting practices and, lastly, the policies. Examples of successful energy conservation endeavours include automatic peak electrical load control, waste heat recovery from mine air and compressor cooling water, energy reductions resulting from lower building temperatures and curtailment of idling loads. The use of pulse meters to measure the flow of gas, steam, compressed air and electrical energy, with their signals interfaced to process computers, allows monthly, daily and, if necessary, immediate reporting of energy and energy per unit of production information The program so reported at Falconbridge&apos;s Sudbury Operations is credited with an annual cost avoidance of .9 million dollars in a 14.0-million-dollar annual energy account

Jan 1, 1979

By Donald C. Myntti

INTRODUCTION A major segment in a successful heavy equipment maintenance and repair program is the provision of well-laid out and well-equipped shop and service facilities The facilities described here will be those required for a large, high tonnage hard rock open pit mine utilizing rotary drills, shovels, haulage trucks, support equipment, and service trucks. The term support equipment covers the equipment required to support the drill, shovel, and truck operations, these are crawler tractors, road graders, front-end loaders, water trucks, rollers, rubber-tired tractors, etc. Service trucks are the automotive type consisting of rubber-tired over-the- road equipment. The primary structures generally involved in the total maintenance effort are as follows. (1) the main shop with an attached warehouse (the structure could also house the tire and lube shops plus the equipment cleaning stalls), (2) a service station with bulk petroleum product storage tanks, (3) a heating plant, (4) a security station (lf this is a corporate requirement), (5) operating department and employee assembly buildings, and (6) an electrical substation. Under certain conditions, many of these facilities with the exception of the substation could be combined In one or several structures. This arrangement could have a great advantage especially in areas where the heating of the structures is extremely critical.

Jan 1, 1979

By Allan T. Fisk, Carl R. Peterson, Robert G. Lundquist

A long recognized goal in high speed tunneling and mining has been the development of a continuous drill and blast excavation capability. Both the advance rate and the economy of drill and blast tunneling can be significantly improved if the conventional cyclic process can be carried out continuously. Obviously, any continuous drill and blast tunneling machine must be an "all function" device, performing drilling, explosive loading, initiation, mucking, ventilation, roof support (if necessary), and perhaps other functions, essentially simultaneously, while remaining at the face throughout. Furthermore, such a machine must do all these things under remote control. THE SPIRAL BLAST PATTERN Several continuous drill and blast tunneling concepts have been proposed. Of these the Rapidex spiral blast pattern, taking advantage of a partially self-shielding geometry, seems to require the least shielding and hence offers the maximum access for mucking, although from the outset it was clear that remote mucking would present a major design challenge. The Rapidex continuous spiral blast concept uses an unusual blasting pattern that, under the geological conditions tested, has proven to be an effective and efficient means of fragmentation. The concept has a self-shielding characteristic which permits a lightly shielded machine to remain at the face during blasting. The pattern produces a spirally proceeding tunnel face, much like one turn of an auger. The leading portion of the spiral surface is connected to the trailing portion by an axially extending plane surface or bench. The ideal geometry is illustrated in Figure 1 for a horseshoe tunnel section.

Jan 1, 1979

By D. A. Viljoen

An account is given of the development of man&apos;s interest in the recovery and working of minerals from Palaeolithic times to the present. This is followed by a discussion of future production trends for the more important minerals, and of likely technological developments in the recovery of various minerals. The crucial importance of energy minerals is stressed, as are several other factors of significance to a flourishing minerals industry: manpower, education, financial climate, Industrial health and safety, and preservation of the environment.

Jan 1, 1979

Orebodies of the Renison Bell - Mt. Bischoff tinfield in Tasmania are stratabound, conformable lenses of massive cassiterite-bearing pyrrhotite, with underlying discordant, fault-fracture-controlled and more siliceous ore. The deposits occur in eugeosynclinal, trough-deposited sedimentary and mafic volcanic rocks which are stratigraphically equivalent to diff erentiated volcanic rocks that contain volcanogenic massive base metal sulphide deposits in a parallel arc to the east. Textures of the massive pyrrhotite ore suggest that it has undergone metamorphic recrystallization. Although the massive ore contains both monoclinic and hexagonal pyrrhotite, a study of a few samples from one orebody suggests that their distribution is stratigraphically controlled, with the monoclinic variety abundant only at the base. The distribution pattern of rare-earth elements in massive ore is similar to that of volcanogenic massive base metal sulphides in New Brunswick, and suggests that mixing of sea water with exhalative hydrothermal brines occurred during ore deposition. Tin is a common accessory element in many volcanogenic massive base metal sulphide deposits providing strong evidence that it, too, is transported and deposited by volcanic affiliated hydrothermal brines. Sedimentary rocks containing the massive orebodies are fine grained, thinly laminated, compositionally banded and of mixed chemical sedimentary-tuffaceous origin. They include finely recrystallized chert, carbonate-rich and pyritic varieties; and soft sediment deformation structures in these rocks suggest that dense sulphides deformed underlying, less dense chert prior to lithification. Close to ore the chert becomes massive and coarsely recrystallized, as does the carbonate, which is here strongly enriched in Fe and Mn. Apatite is present in pyritic, cherty and carbonate-rich beds and in the ore itself, in all of which it shows a similar pattern of rare-earth element distribution, suggesting that it is of marine sedimentary origin. These deposits have traditionally been considered as epigenetic replacements of favourable carbonate horizons by hydro thermal flu ids derived from later Devonian porphyritic intrusions. Some of these intrusions have associated tinbearing greisens. The above relationships suggest, alternatively, that, like massive base metal sulphides, the tin deposits were of original syn-sedimentary origin. Circulating hydrothermal brines generated during early Cambrian eugeosynclinal subsidence and tectonism rose through steep fault-fractures, there giving rise to the discordant orebodies, and were discharged on the sea floor, where the massive pyrrhotite lenses were precipitated with the associated cherts and carbonates. In some places, Devonian intrusions remobilized the earlier deposits, forming greisens and newepigenetic veins. Finally , the geologic selling of these deposits, in trough deposited sedimentary and mafic volcanic rocks, suggests another favourable environment for massive sulphide exploration which is quite different from the domal felsic volcanic environment so heavily favoured currently in North America

Jan 1, 1979

By Michael D. Sopko

This paper describes the project implementation from financing, through the engineering and construction phases, mine and process plant commissioning as well as operating experience realized to-date. The single line flowsheet used to process the lateritic nickel ore to a 75 percent nickel matte is presented with emphasis on the main pyrometallurgical operations. These include a rotary dryer, a unique reduction kiln, a 45 000 kVA electric furnace and two Pierce-Smith type converters. Associated infrastructure facilities and services necessary to sustain the 11 300 tonnes (12 500 short tons) per year nickel production rate are also described.

Jan 1, 1979