Search Documents

By Richard C. Fox

"Why geophysics? We will have to drill anyway." Reliance on geophysical methods for detailed target appraisals will increase as direct surface evidence becomes more subtle. This will create a need for more effective and efficient geo- physical programs. Numerous computer-based techniques that deal with a broad range of geophysical problems are described in the literature. The purpose of this chapter is to provide a framework for the systematic application of these techniques to effect an overall optimization of the geophysical appraisal. The concepts described are not technique specific, but should serve as a guide for increasing the effectiveness and efficiency of any geophysical program. Fig. 1 shows a generalized flow chart of the major aspects of the program described. The three main subdivisions of a 'geophysical program are discussed: (1) survey design, (2) data processing, and (3) data interpretation. Detailed flow charts, outlining the goals, the requirements for meeting the goals, and the steps followed within each subdivision are presented at the beginning of each section. The objectives and type problems of each subdivision are defined, followed by a description of applicable computer methods. . References are cited that give a general cross section of computer techniques available in the literature, and examples are given in each subdivision to demonstrate basic concepts and the use. of computers in solving the type problems.

Jan 1, 1979

By Thomas L. Kesler

Lithium raw materials usable with present technology consist of pegmatite ore and shallow evaporite brine. Deposits of these materials occur in many parts of the world. Those advantageously located supply the present lithium industry. Less favorably located deposits will come into production as markets expand and present sources are depleted. In this discussion, materials listed as reserves include fully explored and partly explored deposits. For those closely drilled and assayed, the data provide measurements rather than estimates, and such reserve tonnages are "proved." For deposits partly explored, the data support reserve estimates of "probable" tonnages. Materials lacking exploratory data are classed as resources, and their "possible" tonnages are inferred mostly from indirect evidence and are essentially objectives for exploration. All figures for pegmatite ore apply to total materials in the ground.

Jan 1, 1979

By Rolf Lange

Introduction The Harzwasserwerke, a public body of the Federal State of Lower Saxony, supplies drinking water to an area bordered by Braunschweig, Bremen, the Northern and the Western edges of the Harz-Mountains. From the very beginning in 1928, the Harzwasserwerke have been systematically constructing reservoirs in the western Harz which have the function of collecting and storing the frequently occuring flood waters as well as providing drinking water. The Grane-Reservoir with a capacity of 45 Million cu.m., the last of the big reservoirs, was built in 1968-1970. A system of connecting tunnels effectively enlarges the natural catchment area of this reservoir and the surplus waters of the Oker and Radau valleys - where floods occur particularly during the spring - are being conducted to the reservoir. By building the 4.800 m long "Radau-Tunnel", the waters of the Radau valley will now also be used more efficiently and its surplus waters will pass to the Grane Reservoir via this new tunnel and the Oker-Grane-Tunnel which was finished in 1970. The Project The Radaustollen has been planned and put out to tender by the Harzwasserwerke as a conventional "Freispiegelstollen". The horseshoe profile has a cross-section of 8 m2. Lining was required only in disturbed rock areas; lining of the whole tunnel was not necessary. The gradient of the tunnel is 4 % 0 rising = 25 m over the total length of 4.800 m.

Jan 1, 1979

By R. H. Nafziger

Bureau of Mines research has shown that very low-sulfur pressure vessel steels with improved mechanical properties can be prepared by two melting processes. Four pressure vessel steels having sulfur contents ranging from 0.0008 to 0.0040 wt-pct, were produced by the electric-arc furnace or by the electroslag processes. Calcium carbide was used as a desulfurizer in the electricarc furnace. Fluxes containing at least 40 wt-pct CaO provided sufficient desulfurization during electroslag remelting. Element recoveries were higher for electroslag remelting than for metal melted in the electric-arc furnace. Bar rolled from electroslag-remelted ingots generally possessed higher tensile strengths and ductility than bar rolled from it t melted in the electric-arc furnace. Charpy V-Notch upper shelf energies were also improved as a result of electroslag remelting. The primary failure mode during impact testing was was microvoid coalescence. Sulfide inclusions were minimal, especially in the electroslag-remelted material.

Jan 1, 1979

By William C. McBee

Specialized sulfur concretes were developed by the Federal Bureau of Mines as a result of research for the beneficial utilization of sulfur in construction materials. Materials were developed for use in acid and salt corrosive environments where portland cement concrete has been found to deteriorate. Because the mineral aggregates also come into contact with the corrosive media, concretes were developed utilizing both limestone and quartz aggregates. The sulfur binder used with both aggregates was modified by reaction with 5 pct dicyclopentadiene to improve product durability. Sulfur quartz aggregate concrete was found to have moderately high strength characteristics (6,000 psi compressive) and was extremely resistant to chemical attack by both acid and salt solutions. Sulfur limestone aggregate concrete exhibited very high strength characteristics (9,000 psi compressive) and was extremely resistant to chemical attack of salt solutions. Both types of concretes maintained their strength and integrity after long-term testing in acid and salt solutions and exhibited considerable resistance to damage by the action of freezing and thawing. Potential uses include leach tanks, electrolytic cells, thickeners, bridge decking, industrial flooring, pipe, and tile.

Jan 1, 1979

By C. Haycocks

In spite of the increasingly high capital investment required for longwall mining equipment, there continues to be a steady trend towards this form of mining. This move is caused in large part by improved productivity of longwall mining systems combined with greater percentage of coal recovered over room and pillar mining, reduced manpower requirements, and the inherent safety of the system. Longwall mining is most amenable to the greater depths experienced by many mining operations, particularly in the coalfields of the Eastern United States. Two primary problems in the installation of a longwall panel are determining whether a particular seam is suitable for longwall and, secondly, type and capacity of equipment required for such a mining operation. In addition, recent legislation has forced an evaluation of the surface effects of longwall mining with a view to determining what, if any, surface damage might result from extracting any particular panel. These factors must be determined using large and often complex quantities of geological, structural, mining, and surface data. This makes the problem most attractive to solution using the computer.

Jan 1, 1979

By L. A. Stinnett

An investigation of hazardous surface openings of abandoned and inactive underground mines in the Black Hills area of South Dakota has revealed: (1) tracing legal ownership of mineral claims via county courthouses is confusing, complex, and oftentimes misleading, (2) in general, the selected mine openings in this investigation are to be considered relatively high in risks and hazard potential which poses a threat to the general public, (3) mine closure procedures and designs can generally be categorically implemented depending on the overall situation of the particular mine opening with subsequent unit costs estimates, (4) few preventive state or federal legal measures exist to date concerning mine closures, and (5) liability damages relating to mine opening accidents usually involve expensive and complex common law cases.

Jan 1, 1979

By N. A. Barcza

An investigation was conducted into the reactions between the slag system MnO-CaO-MgO-SiO2(AI2O3) and the alloy system Mn-Fe-Si-(C). Synthetic slags representative of plant melts and a plant alloy were reacted in alumina crucibles at temperatures of 1400°C, 1450°C, 1550°C, and 1600°C. In similar experiments, slags were used that comprised a South African manganese ore with various amounts of lime and several synthetic alloys with various silicon contents and manganese-to-iron ratios. These experiments were conducted in a vertical molybdenum-wound resistance furnace with full temperature control. Slag-to-alloy ratios were also varied during the tests. The rate of reduction of Mn.O3 and the MnO from the slag by the silicon in the alloy was extremely rapid, most of the reaction being completed within five minutes. The strongly exothermic nature of the reaction resulted in considerable generation of heat at the slag-alloy interface, causing convectional stirring of the contents of the crucible and promoting the rate of reaction. Equilibrium was usually attained after fifteen minutes. The major limitation governing the recovery of manganese is the need for the silicon content of the alloy to meet a maximum specification of 2 per cent. Higher concentrations of silicon in the final alloy of between 8 and 12 per cent favour good recoveries of manganese from the slag, but, since such an alloy is not salable, lower recoveries must apparently be tolerated. In alloys of 2 per cent silicon, low activities of the silicon are responsible for poor recoveries of manganese. The activity of MnO in the slag can be increased by moderate additions of CaO and small amounts of MgO, i.e., by an increase in the basicity of the slag.

Jan 1, 1979

By Bruce T. Olenchuk, Wils L. Cooley

Electrical grounding is essential for the safe operation of power systems. A low-impedance path to ground is necessary to prevent the possibility of dangerously high potentials in human work areas. If for any reason this ground connection becomes faulty, a serious hazard may exist. One reason for faulty ground connections is ground bed corrosion. Corrosion of electrical ground rods has plagued the power industry and appeared in coal mine power systems. This paper will investigate ground rod corrosion, its cause, and possible solutions. Included is an evaluation of various ground rods for their ability to resist corrosion under stray current conditions. -The first known study of X-it3 Rod Corrosion is also presented.

Jan 1, 1979

By William H. Hamilton

This report describes the results and conclusions of the development and evaluation of a unique concept for a lightweight air powered drill tool for probe drilling in anthracite mines. A concept model of the lightweight air powered tool was constructed and evaluation testing conducted at the Kocher Coal Company Porter Tunnel Mine. The unique anchoring method proved to be extremely satisfactory and the overall light-weight air powered drill tool concept proved feasible. Based on the results of the concept model testing, two prototype production units were designed and manufactured. These prototype units proved to meet all of their design requirements of lightweight, portability, drilling controllability, structural integrity and miner acceptance. The need for a better bit and drill steel system, however, became evident during the testing program and recommendations are made for further investigation and development of a bit and drill steel system suitable for this application.

Jan 1, 1979

By V. L. Magnus

The text of this chapter was not received in time for printing.

Jan 1, 1979

By J. A. Herbst, J. L. Sepulveda, J. D. Miller

Lead cake, a zinc smelter flue dust residue, consists primarily of lead sulfate. Characteristic properties of lead cake were determined in order to aid the understanding of reaction mechanisms involved in bismuth removal from lead cake by sulfuric acid digestion. Sp gr (specific gravity) measurements, surface area measurements, and photomicrographs revealed that the particles of lead cake are quite porous and seem to consist of an agglomeration of submicron grains (0.4 pm) fused together in a manner similar to cement clinker. Analysis of experimental rate data, which was independent of particle size, indicates that the dissolution reaction involves two distinct, rate limiting steps. The initial stage of reaction appears to be limited mainly by intergranular diffusion of the reactant, hydrogen ion, while the latter stage of reaction appears to be controlled by diffusion of soluble reaction products through the reaction product layer of the individual grains.

Jan 1, 1979

By J. A. Finch

Samples of feed and product from a closed grinding circuit treating a heterogeneous lead-zinc ore were taken. The feed was subjected to laboratory batch grinding in a rod and ball mill with the objective of simulating the closed-circuit size distribution. It was concluded that the batch rod mill can closely simulate this product if only the over-all size is considered, but mineral-by-mineral large differences occur. If, as is suspected, the mineral sizes are the important factor in flotation, the differences could lead to problems in interpreting flotation results. An example of mineral recovery as a function of size is described to illustrate the potential problems.

Jan 1, 1979

By Arthur F. Colombo

The selective - deslime - flotation process developed by the Federal Bureau of Mines as part of its goal of maintaining an adequate supply of minerals to meet national economic and strategic needs is described. The operating parameters for the selective flocculation - cationic flotation of oxidized taconites from the western Mesabi range in Minnesota are discussed. Data from the operation of a 410 kg/hr (900 lb/hr) pilot plant employing reclaimed water are summarized for 2 types of oxidized taconites.

Jan 1, 1979

By Ronald L. Sanders

The prevailing view of the coal mining industry by government officials is: "Tell everyone you're coming - Don't let anyone know you're there - And remove all evidence you have ever been there". Now the irony is that the government inspectors are just enforcing the law. The coal mine operators seem more interested in genuine reclamation than the inspectors.

Jan 1, 1979

By Tyler R. J

Methylene blue dye adsorbs on chalcopyrite concentrates slurried in aqueous solution. Saturation adsorption can be achieved within about 24 hours for dye equilibrium concentrations greater than about 10-5 M. The dsorption coverage is obtained from a measurement of the' colour change of the solution. Comparison with BET measurement of the concentrate surface area shows that 2.4 ± 0.1 µmol of methylene blue are adsorbed per square metre of surface accessible to the dye cation. The procedure described can be used as a single-point measurement and values for the surface area can be otained to within about 10 per cent with inexpensive instrumentation.

Jan 1, 1979

By Goran Mathisson

In several investigations the correlation has been studied between the fuel consumption and the reducibility of the charged material in the zone of indirect reduction in the blast furnace (1, 2, 3, 4, 5). It has been found that increased reducibility allows greater gas utilization which accordingly lowers the fuel consumption. In direct reduction units this relation has not yet been fully established partly owing to the lack of accurate test methods and experience with different materials as regards reducibility. However, since the production rate in a direct reduction unit is closely related to the time required to reach high degrees of reduction, the reducibility must be regarded as one of the most important properties of the material.

Jan 1, 1979

By K. V. S. Sastry

INTRODUCTION Flotation is by far the most important unit operation of mineral processing. Most of the common base metals are produced from flotation concentrates of metal sulfides. Flotation is proving to be a valuable process for producing non-metallic minerals such as ceramic oxides, silicates, clays and phosphate fertilizers. All these fltation separations are carried out on materials which are predominantly in the 10 to 100 micronssize range. The present practice of flotation circuits for the production of large tonnages of metallic and non-metallic mineral concentrates is fairly well understood, developed, and standardized. Two kinds of problems are encountered (1, 2) with fine particles smaller than 10 microns. First is the interference of the fine particles with the flotation of the coarser particles and the second is the poor flotation behavior of fine particles. In general, these problems are handled either by eliminating, minimizing, or ignoring the fines in the flotation circuit feed. In recent years, however, a considerable number of experimental and theoretical studies have been carried out to understand the flotation behavior of fine particulates. This literature is summarized in four review papers (2-5). Application of the conventional flotation techniques for the separation of mineral fines is known to be uneconomical, and to present several scientific and technological problems (1-5). The objective of this presentation is to examine the flotation behavior of fine particles in terms of their physical-chemical properties and to review the potential techniques of fine particle flotation. Specific reference to the problem areas and research needs will also be included in the discussion.

Jan 1, 1979

By Stanley M. Miller

Analysis of discontinuous rock masses for engineering design purposes requires information about fracture characteristics. For such studies, fractures or other elements of the rock fabric (bedding, foliation, etc.) should be considered in a statistical manner because they generally have high frequencies of occurrence and are discontinuous over the design area. A practical design procedure includes defining structural domains as those areas which contain fractures with similar orientation patterns. Within a structural domain, the statistical distributions of fracture set characteristics (spacing, fracture density, dip, dip direction, etc.) may be computed from mapped data and then used to quantitatively describe the rock fabric. These distributions can then be randomly sampled (using Monte Carlo techniques) to simulate the rock fabric and to help define potential failure surfaces along fractures. 1 The prediction of failure geometries is an essential part of stability analyses used in designing rock slopes or underground openings. In current probabilistic design procedures, Monte Carlo techniques that rely upon the iterative generation and analysis of deterministic instability models do not incorporate spatial aspects of the random variation in fracture set characteristics, 1,2 but consider the characteristics to be spatially independent.

Jan 1, 1979

By M. Adnan Goksel

A blast furnace test of approximately 5,000 tons of PelleTech Corporation (PTC) cold bond pellets was successfully run at Kaiser Steel Corporation (Kaiser) Steel Manufacturing Division at Fontana, California. The pellets were produced from mill scale, BOF dust and blast furnace flue dust. A 15 day base period, during which time the metallic burden was 2/3 heat indurated pellets and 1/3 sinter, preceeded the test. During the test period the metallic bur- den was 10% cold bond pellets, 56.7% heat indurated pellets and 33.3% sinter. A 15 day post test base period followed during which the PTC pellets were replaced by conventional pellets. The pellets were produced in the 3.C Semi-works Facility located on Kaiser property. The facility incorporates the Michigan Technological University Hydro-Thermal Agglomerating Process.

Jan 1, 1979