Search Documents

By Milne J. Schmid

A program has been conducted to determine the feasibility of providing a borehole liner for Kelly Bar drilled boreholes in Southern Florida. The concept was to drill the borehole with the Kelly Bar and with it still in the borehole insert a tube which would remain in the unstable ground after withdrawl of the bar. The tube then will provide an unobstructed borehole for the charging of explosives upon completion of the drilling the shot pattern.

Jan 1, 1977

By Roland Hunt

This paper deals with the practical problems as sociated with blasting a heated pillar remnant. This pillar remnant was the final stage in the blasting of a multi-stag e pillar blast. Production from the previous stages had produced burning sulphide ore, resulting in high rock temperatures in the final unblasted stage. This is an account of how, under difficult conditions, the pillar remnant was blasted.

Jan 1, 1977

By G. J. Hundman

Control of respirable dust produced by auger type continuous mining machines is normally attempted by water sprays from fixed nozzles mounted on the frame of the machine. In tests conducted under this contract, a 'wet auger' system was used, where the spray nozzles were mounted on the rotating auger itself. The tests were conducted at the Hunter mine of Smith and Stover Coal Company using a Jeffrey 1.00L auger miner. Operating the mining machine in the wet auger mode, it was found to produce 47 pct less respirable dust than when the fixed conventional sprays were used. On section dust levels were reduced too 3.5 mg/m3 which is equivalent to approximately 2.0 mg/m3 for a full shift portal to portal sample. The major difficulty that had to be overcome was the development of a simple reliable water transfer mechanism to get the water into the rotating augers. This was successfully achieved by the development of a water-through-the-shaft water system. This system can be retrofitted to existing machines and is available in kit form.

Jan 1, 1977

By L. H. Smith, D. S. Taylor

"AbstractSherritt has been applying hydraulic drives to concentrator equipment since 1967. The initial application was made on a bank of 5- by 5-in. slurry pumps. This has now been extended to all slurry pumps requiring less than 40 hp and several conveyors which require variable-speed or low-speed/high-torque characteristics. The pump motors are directly connected through a flexible coupling, whereas the conveyor systems are directly mounted onto the head-pulley shaft extension.The different applications and design concepts will be described, with outlines of the operating and maintenance advantages and disadvantages and costs. The paper also outlines future possible applications, together with the limiting conditions, of such systems.IntroductionSHERRITT GORDON MINES LIMITED has been operating a mining division in Northern Manitoba for almost 50 years. The original mining operation was at Sherridon, Manitoba and was a copper-zinc producer. This mine was exhausted in 1948 and the mining plant was moved north to its present location at Lynn Lake, Manitoba. The Lynn Lake Mine is a nickel-copper producer. Since 1960, two new mines have been discovered and brought into production in the general vicinity of Lynn Lake. The first of these was the Fox Mine, a copper-zinc property operating at 3,000 tons per day from an underground operation. This mine started production in May 1970."

Jan 1, 1977

By Wilfrid Comeau

Since 1967 Hydro Quebec has undertaken the control of blasting and its effects at its power development sites. Blasts have been monitored using a commercially available three component seismograph. Initially, vibration records were used to establish the relationships between vibration level (resultant of three components), explosive weight and distance for various blasting operations.

Jan 1, 1977

By R. L. Wiegel

Consideration has been given to the merging of a size reduction model and a mineral liberation model to permit prediction of mineral composition as a function of size. The results of this integration of size reduction and mineral liberation models are discussed from both theoretical and practical viewpoints using batch grinding data for a magnetic iron formation sample as a demonstration vehicle.

Jan 1, 1977

By Laszlo Valentyik, John T. Patton

A conventional heavy-media separation process utilizes a mixture of finely ground solids like magnetite, ferrosilicon, or shale and water. The always-present clay in the medium acts as a stabilizing agent since the coarse heavy-media solids would quickly sink if they were mixed only in water. As the pseudoplastic nature of polymer solutions has excellent suspending properties, laboratory investigations were conducted at the Institute of Mineral Research on whether polymers could be used as suspending agents for finely ground heavy media. The preliminary results (published previously) of the laboratory research studies have shown that sufficient stabilities of heavy media can be obtained at a relatively low polymer concentration. This paper is a continuation of the previous work and it presents some of the results of recent studies where the rheological properties of the heavy-media suspensions were studied in a newly developed settling tube and the already familiar concentric-cylinder-type consistometer. In the investigations bentonites as a stabilizing agent also were included so that comparative results would be available to the plant engineer to assist him in the choice of the most suitable material for stabilizing various heavy media.

Jan 1, 1977

By Carl R. Peterson

The Rapidex continuous drill and blast tunneling concept utilizes a unique spiral blasting pattern that permits efficient performance with relatively small single shots, while at the same time directing major blast fragments at right angles to the tunnel axis. The concept's self-shielding geometry permits the design of a lightly shielded machine that can stay at the tunnel face firing frequent small blasts to provide rapid, virtually continuous advance. This paper describes Phase III of the development program (supported under Bureau of Mines contract H0252047) in which the "front end" of the machine?drilling loading, and shooting components, together with the shield--was fabricated and field tested underground at the White Pine Copper mine, Michigan. One of the major accomplishments of the Phase III effort was to develop a fully remote controlled loading and initiation system in which explosive slurry is pushed, through a hose into the blasthole by a small water-driven piston carrying the blasting cap. The cap is ignited via an induction coil just prior to entry into the borehole, after which a delay permits complete -withdrawal and shielding of the loading hose. The ultimate objective of the present Bureau-sponsored program is to evaluate the feasibility of mechanizing hard rock mining operations, such as development to a point where drilling, loading, shooting, and mucking can proceed simultaneously and result in increased productivity.

Jan 1, 1977

In this issue, the Bureau of Mines announces the availability of the latest of its Mineral Perspectives series: ?MP-4, mineral Industry of Western Europe." This publication describes the mineral industries of 19 Western European countries. For readers unfamiliar with this new series, reproduced below and on the two succeeding pages, is the section dealing with the mineral industries of France. Information regarding acquisition of this publication is found inside the back cover of this issue. FRANCE France is a moderately important producer of minerals, including iron ore, coal, potash, fluorspar, and uranium. In addition, France is a significant processor of imported minerals, chiefly for its own consumption. In general, it has exportable surpluses only of a little iron ore (low-grade ore exported to Luxembourg) and some nonmetallics.

Jan 1, 1977

By F. Lawson, N. A. Sareyed-Dim

A rotating disk of iron precipitant in a high temperature batch reactor has been used to study the kinetics of precipitation of nickel from low concentration aqueous solutions. Under inert atmosphere conditions, for temperatures up to 150°C, the rate of nickel deposition at pH25°C of 5 to 6 is controlled both by the rate at which nickel ions reach the surface and the rate of chemical reaction at the surface. However, the presence of oxygen in the atmosphere above the reacting system increases the nickel deposition rate dramatically. It is suggested that under the experimental conditions used, hydrogen atoms are adsorbed on both the iron and nickel, thus reducing the number of sites available for the cementation reaction. Oxygen acts as a depolarizer for hydrogen.

Jan 1, 1977

By E. C. Winegartner, A. A. Ubbens

The company attempting to sell coal to large utility plants is faced with a confusing array of quality parameters and specifications which are often poorly understood by both the utility company and coal supplier. While these specifications are placed on the coal by the utility company, many of them originate with the boiler manufacturer who must guarantee that his product will perform satisfactorily on the design coal. A proper understanding of these parameters by both the coal supplier and utility company can lead to a better understanding of their mutual problem. This paper brings together most of the parameters in common use today and attempts to show what the parameters mean to the boiler designer, particularly in the area of boiler slagging and fouling.

Jan 1, 1977

By John D. Shaw

1. Introduction 2. The Hydraulic Mine _ (i ) Development (i i ) Extraction ( i i i ) Transport 3. The Water Circuit 4. Manpower and Results 5. Modifications 6. Conclusions 1. Introduction The Kaiser Resources Ltd. hydraulic coal mine is located in south eastern British Columbia, Canada, at the western end of the Crowsnest Pass, next to the Town of Sparwood. The seam presently being mined is the number 10, known locally as the Balmer seam, which is a high quality coking coal, 50 feet in thickness and of an average inclination of 35 degrees. The mine was designed in the late sixties as a small scale trial unit, and was to use a single monitor unit, working 3 shifts per day on a 5 day per week basis. Experience has proved the method to be so successful as to warrant the expansion of the ancilliary facilities to cater for the increased production. The annual raw coal production from this single monitor unit has risen from 108,988 short tons in 1970 to 942,334 short tons in 1975, with a total mine labour force of about 160 men including the surface de-watering plant, mine supervision and mine administration.

Jan 1, 1977

By Constance F. Acton

Based on laboratory structure analyses, a pilot plant investigation was undertaken to evaluate a Michigan conglomerate native copper ore. Comminution or sized feed was accomplished using wet, closed circuit autogenous grinding with and without crushing of the recirculating load. Coarse metallics were concentrated in two stages of jigging with fine metallic copper being recovered in a three-stage xanthate flotation circuit. With a feed averaging 2.09 % Cu, copper recovery ranged from 86-93 % Cu with an average grade of 55.5 % Ca. An evaluation of the processing flowsheet is made in terms of pertinent independent, dependent, and external variables and design factors. Rate equations are developed to describe the grinding and flotation circuits separately as well as the entire circuit as a whole. Performance equations for the overall operation and for the unit operation of autogenous grinding alone are developed in terms of suitable capacity, efficiency and energy consumption terms. Thus, the effects of feed rate, recirculating load and flowsheet design can be rationally evaluated. Energy consumption for various conditions in the pilot plant is compared to the laboratory value. Additionally, size and scale up factors are discussed. Recommendations are made for further studies to be undertaken to further quantify the ore characteristics and the nature of the autogenous grinding operation. However, the feasibilty of beneficiation of this type of native copper ore by means of an autogenous grinding/jigging/flotation circuit is clearly established.

Jan 1, 1977

By Joseph Cervik

This Bureau of Mines report deals with water infusion of coalbeds, which can control methane emission at face areas during developmental mining and which may sometimes suppress dust. Studies show that water infused into the coalbed flows through the fracture system and displaces the methane in the fractures and prevents migration from the solid coal. Displaced gas migrates away from the face area that has been water infused and enters the return ventilation airways. A gradual decrease in methane emission is observed from the start of infusion until the infused zone is mined through. Depending on the permeability of the coalbed, infusion pressures ranged from 300 to 2,200 lb/in2. Face emissions in the Upper Kittanning coalbed were reduced by 89 pet; reductions of 38 to 79 pet were measured in the Pittsburgh coalbed depending on the relationship between the face cleat direction and mining direction. Respirable dust levels were reduced by about 75 pct on a longwall section in the Pocahontas No.3 coalbed and by about 50 pct on a development section in the Upper Kittanning coalbed, but no statistically reliable reduction was found in the respirable dust levels in the Pittsburgh coalbed.

Jan 1, 1977

By Van Barnefield J G

This paper is based on an evaluation project engaged upon jointly by Mount Isa Mines Limited nnd" IBM Austra]ia Limited. Mount Isa Mines Limited produces most of its copper from large underground open stopes within massive orebodies. Variations in the position and shapes of these stopes can result in improved metal recovery. An interactive graphics system has been developed to assist the mine design engineer optimise his design. The system can assist the engineer throughout the orebody visualis- ation, initial design and optimisation phases of his design. At any stage the engineer may call upon the display of gridded mesh data, digitized ore outlines or existing stopes or development (drives, cross-cuts). This information may be viewed in plan or any vertical section or in three dimensions with rotation. Tonnage and grade calculations may be quickly performed for initial stope outlines or for modifications to them during the optimisation phase. The system design is highly modular. An array of functions for the manipulation of coordinate and line information may be linked with the development or stope design functions in whichever way the designer desires.

Jan 1, 1977

By Donald H. Matthews

I wish to preface my remarks with the warning that I, in no way profess to be an authority on the U. S. Department of Transportation, Hazardous Materials Regulations, 49CFR Parts 100-199, nor attempt to advise any one on the regulations or how they should conduct their business in relation to the regulations. I merely wish to convey my interpretations of the regulations and some of the procedures adopted by my company to comply with these regulations, with the hope that this information may help others to better understand the regulations and help them formulate their own procedures for compliance. I will cover nine problem areas and furnish sources of information for anyone concerned with explosives transportation.

Jan 1, 1977

By William C. Brice

Minnesota is involved in planning controversies related to taconite and potential copper-nickel mining. Mine facility planning includes the Reserve dining on-land tailings disposal issue and the potential for a new copper-nickel mining district. Both provide a unique opportunity for innovative planning in the attempt to be responsive to public and private interests. Concerns that emanate as a result of mineral resource activities include environmental protection, land use competition, land exchanges, highway and utility extensions, and legal constraints on public or private lands. The purpose of this newly-developed planning approach is to anticipate such issues and provide a rational information base for dealing with them. The result will be a framework plan for guiding public planning, and an impact assessment for reviewing the implications of industrial project proposals. The approach uses a computer-stored resource inventory of natural and cultural information. Geographic data is mapped and entered into a computer storage and retrieval system. This enables systematic analysis of mineral resources along with environmental and land use considerations. Computer mapping describes the relationship of each activity and allows identification of potential conflicts; it also shows geographical extent in the form of statistical compilations. Resource data is being collected and compiled using a standard metric grid (Universal Transverse Mercator). Individual cells are 100 m. squares and represent areas of about 2.5 acres. The study area contains about 145,000 cells. Data inventories are being compiled in 25 natural and cultural resource categories. Geologic variables include Bedrock Geology, Taconite Reserves and Potential Resources, Depth to the Duluth Complex Contact and two soil inventories. Topographic and hydrologic variables include elevation, slope, slope orientation, surface hydrology, and watersheds. There are also 6 biological data variables and 7 land use inventories.

Jan 1, 1977

By Donald L. Freed

Design, development, factory test, and in-mine evaluation plans are presented for an Automated Extraction System (AES) that has been designed to fill needs which are present in the Mining Industry. The philosophy of design and proposed operation of the machine, as well as the relationships between these factors, and final machine configuration are reviewed. The AES is designed to overcome production problems resulting from the regulation of roof control, clean-up, ventilation, dust suppression, and operator protection required by the Federal Coal Mine Health and Safety Act of 1969. The design permits more continuous operation and greatly improves operator safety. The machine is a full-face drum-type continuous miner which includes self-advancing, continuous temporary roof support. Onboard self-advancing face ventilation, dust suppression, and air scrubbing equipment are also included in the design. A further improvement over existing equipment is the incorporation of an automatic programmed cutting cycle control system. All mining functions including movements of the roof support system are handled by this automatic system.

Jan 1, 1977

By Donald B. Larson, Milton Finger

The use of explosives in deep rock mining carries conventional blasting technology into a relatively new and unexplored realm. Although bill ions of pounds of explosives are used fairly routinely in mining, quarrying, and construction, almost all of these uses are surface blasting. Most of the in sib processes that are proposed for recovery of mineral or energy resources require the creation of high permeability to provide well defined flow paths in the resource bed. At present there is very little information on the fracturing produced by explosives deep in the earth, and the technology for using explosives in deep rock mining is just evolving. A qualitative understanding of the applicable mechanisms in deep rock fracture leads to some key parameters in the selection of explosives for deep rock mining. The selection and characterization process involves a careful analysis of the field environment and the establishment of tests to determine candidate explosives response to planned and accidental stimuli. The details of this selection and characterization process are given for a few candidate explosives. The use of explosives in deep rock mining must be considered as one of the possible tools for recovery of yet untrapped energy and mineral resources. A basic understanding of explosive deep rock fracture will allow optimum selection of explosive processes or other more appropriate methods for recovery of energy or minerals from a particular resource area. The results of some experimental studies are discussed.

Jan 1, 1977

By Folie M

Energy models are evaluated according to their contribution to policy decisions. The view taken is that if any model is to provide policy insights, it should be based on economic theory. The difference in modelling methodology between economists and technol- ogists is discussed. The technique of energy analysis is criticised. The basic structure of some of the large economic models is presented and their policy usefulness is Discussed.

Jan 1, 1977