Search Documents

By Marshall D. Himes

The Pima mine, Pima County, Ariz., a 53,500-tpd copper mine, is located 17 miles south of Tucson, Ariz. The mine is in a sequence of Paleozoic and Mesozoic sediments striking east-north-east and dipping southeasterly. These sediments are intruded by a Tertiary quartz monzonite porphyry. The Paleozoic Permian (?) dolomites, limestones, and sandstones have been altered to calc-silicate skarn, marble, and quartzite. The overlying Mesozoic Triassic (?) clastic sediments have undergone some recrystallization and hydrothermal alteration. The clastic metasediments are divided into three distinct lithologic units: lithic arenite, arkose, and interbedded and overlying black argillite. Three types of hydrothermal alteration in the clastic rocks are propylitic alteration (epidote, chlorite, and quartz, with or without sericite), quartz-sericite alteration, and potassic alteration (K-feldspar, quartz, and sericite, with or without chlorite and calcite). The porphyry has undergone potassic alteration. Dominant structures are an east-west postmineral fault in the western part of the pit, and strong low angle faulting and shearing which truncates the ore body at depth. The two joint sets, one parallel to bedding and the other at right angles to bedding are prominent in the mine. Faulting is in two dominant directions, one striking northwest, dipping northeast, and the other striking northeast, dipping northwest. Economic mineralization is prediminantly disseminated pyrite and chalcopyrite, and molybdenite-quartz veinlets. There are less important amounts of magnetite, hematite, sphalerite, galena, tennantite, and bornite. Mineralization is believed to be both structurally and chemically controlled.

Jan 1, 1974

By Jack E. Fraley, Robert E. Simpson

INTRODUCTION Spokane Mining Research Center (BuMines) is researching sealants for underground coal mines to: 1. Reduce sloughing of shale roofs. 2. Reduce sloughing of coal ribs. 3. Seal block stoppings against air losses. 4. Construct stoppings by spraying over jute cloth or metal lath. 5. Render incombustible in-place polyurethane foam. Originally the work was directed towards reducing sloughing of shale roofs. Many underground coal mines have shale directly over the coal which weathers severely after exposure to the mine atmosphere. Lab investigations(l, 2, 3, 4) have shown that many shales separate into layers when immersed in water or stored in a high relative humidity environment. Upon drying or after removal from high humidity, the shales continue to separate. Underground coal mines become wet in the warmer months from condensation of the ventilating air. Conversely, the mines become dry in the cooler months from evaporation. The mines experience severe shale break-up during the summer and much less break-up during the winter. Figs. 1, 2 and 3 show weathered shale roofs. in underground coal mines. Fig. 4 shows fallen shale on the entry floor. Sealing the shale reduces this sloughing problem.

Jan 1, 1974

The panic bars (and associated linkages and electrical circuitry) that are defined in this document are a machine operator-actuated control for the emergency deenergization of the tram motors on self-propelled, electric and diesel face equipment: including haulage equipment such as shuttle cars. There are nine basic types of panic bars (and several variations) that arc recommended in this document, but all of the panic bars are characteristically of the "fire door" type that is frequently encountered on outside exit doors of many public and some commercial buildings. It is also the intent of the following panic bar designs that, when emergency brakes are added to the face equipment machinery for which they arc required, that they be designed and hooked up so that actuation of the panic bar will result in automatic application of the emergency brakes (immediately following the deenergization of the tram motors). The following panic bar design requirements are a restatement of the proposed requirements defined in the Federal Register, requirements cited in "Guidelines for the Design and Installation of Devices for Deenergization of Self-Propelled Electric Face Equipment/Automatic Emergency Brakes" by C. E. Lester and J. D. Greenhalgh of MESA, and Bendix recommendations that were formulated as a result of discussions with personnel al the various machine manufacturers and underground coal mines that we surveyed, discussions with G. L. Judy (our consultant), etc:

Jan 1, 1974

By Curtis D. Edgerton

Miami Oölite limestone is the only significant construction mineral in southeastern Florida. Its source area coincides with that of rapid urban expansion. Two-thirds of the existing resource is already unavailable because of development. Land-use conflicts place future availability of limestone in jeopardy. However, a sufficient limestone resource to meet demand for many years is present if its extraction is not restricted. Adverse environmental effects of quarrying Miami Oölite are not severe; land values often increase following quarrying. Future availability depends upon--(l) achieving uniformity of Federal, State, county, and municipality statutory requirements governing quarry operations; (2) setting aside specific land areas for future quarrying; and (3) cooperative planning to provide for land utilization upon completion of quarrying.

Jan 1, 1974

By J. A. Herbst, D. W. Fuerstenau

An analysis of the kinetics of dolomite grinding in a dry ball mill reveals that the following approximations apply for the parameters of the batch grinding model: (1) the size discretized selection functions are proportional to the specific power input to the mill, and (2) the breakage functions can be taken as invariant. These approximations are shown to provide the basis for accurate predictions of product size distributions obtained for several mill speed, ball load, and particle load combinations within the normal ball mill operating range. The engineering implications of these findings are discussed.

Jan 1, 1974

By Paul K. Edwards

The forces of nature have concentrated sand at various geographical locations that are being mined and processed for a large variety of industrial uses. While most operations serve a number of industries, this paper deals only with the foundry requirements. The forces that have decomposed a source rock, transported this material and redeposited it, have created two general types of sand. These types are classified as the (1) Lake and Bank Sands and (2) Silica Sands. The Lake and Bank sands will contain 92 to 94% Sio2 while silica sands are in excess of 98.5% Si02 and most of the producers wash these sands to up grade their products to 99.5% or better. Included in the Lake and Bank sand would be the river sands that are used primarily for construction purposes. The Foundry Industry is broken down into three types of castings : 1. Grey Iron Foundries The grey iron castings largest market is the automotive industry in Ohio, Northern Kentucky, Indiana, Illinois and Michigan. These castings are poured at temperatures ranging from 2400° to 2700°F. The Silica Sands or the Lake and Bank Sands will satisfy the requirements of the grey iron castings. There are 2 ½ to three million tons per year shipped from the state of Michigan far grey iron castings by the Lake and Bank Sand Producers.

Jan 1, 1974

During the first quarter of 1973 ADL worked closely with PMSRC staff, under an extremely compressed time schedule, on all aspects of the detailed planning, organization and overall coordination and preparation of the lectures and in-mine demonstrations for the Bureau's Technology Transfer Seminar on Mine Communications given in March of 1973 to representatives of the mining industry. Our efforts centered on the detailed organization and preparation of each of the five technical seminar lectures and associated supporting material, and the coordination of tasks assigned to ADL and other seminar participants. Revised and expanded drafts of the seminar papers were prepared from rough draft versions obtained from PMSRC, Collins Radio and ADL staff. Measurements were made to gather key data on the operation and performance of each of the following systems installed in the Bruceton Safety Research Mine; call alert paging, roof bolt paging, section wireless radio, and guided wireless radio systems. These data were analyzed, manufacturer's equipment specifications utilized, and calculations made to provide performance curves and data for each of the above systems. A substantial amount of artwork was conceived and prepared for 35 m slides, system identification posters in the mine, and seminar handouts. This artwork included some forty 8-1/2" x 11" line sketches, graphs, block diagrams, circuit diagrams, coverage maps, and other line drawings; five 30" x 40" block diagram system identification posters suitable for in-mine use; a 20" x 30" detail perspective illustration of a representative coal mine layout; forty viewgraphs; and seventy 35 m slides of the artwork and word charts. Conferences, discussions and review sessions were held with conference participants to help coordinate the various efforts, obtain technical information, and make final plans regarding the lecture presentations, associated visual aids, and the communication system installations to be demonstrated in the Bruceton mine. These meetings included final systems checkouts and dry run presentations and reviews of the lectures and mine demonstrations. This phase of the seminar effort concluded with R. Lagace and R. Spencer of ADL participating in two days of seminar presentations in the lecture hall and in the Bruceton mine.

Jan 1, 1974

By J. A. Eisele

The Bureau of Hines conducted a bench-scale investigation of a concentrated H2S04 reaction for recovering and separating rare-earth elements, barium, and strontium from a bastnasite ore and byproduct. Barium and strontium were dissolved in the concentrated acid and precipitated as a mixed product by water dilution. Separation of strontium from barium was effected by reaction with Na2C03 solution, followed by a dilute acid leach of the SrC03 formed. After removing the barium and strontium from bastnäsite are, the rare-earth elements were roasted to water-soluble sulfates. The rare-earth sulfate solution was subsequently processed by solvent extraction to produce rare-earth oxides low in lead and magnesium.

Jan 1, 1974

By George A. Savanick

Coal mine roof shales fracture preferentially at slickensided surfaces because of weak or nonexistent adhesion between two slickensided rock surfaces. The purpose of this Bureau of Mines research was to characterize chemically the thin film of smooth, glossy material that makes up the slickenside. This material was analyzed by electron spectroscopy and ion scattering spectrometry while in place on the rock surface and by standard methods of quantitative chemical analysis on concentrate removed from the rock. These analyses showed that the chemistry and mineralogy of the slickensides are similar to that of the adjacent shale.

Jan 1, 1974

By Ted C. Mathews

Pre-concentration by sorting is as old as the mining industry. Inevitably waste rock is broken with ore. Separation may take place in the stopes by selective mucking and transport, or selective loading and transport of ore and waste by 12-cu, yd. shovels and 100-ton trucks in large open pit operations. Hand sorting of 1" to 16" pieces, formerly widely practiced at underground chutes and prior to or following first stage crushing, has greatly diminished in the United States with its high per hour labor cost, although still widely practiced in other countries and, surprisingly, in some of the most modern mills where inexpensive labor is available. The economics of pre-concentration by sorting is attractive since elimination of waste at any cost less than the total milling cost will show a profit. The size at which sorting should be under- taken is determined by the size at which liberation is secured to yield a product of ore and waste, and greatly influences cost and the point in the flowsheet where sorting can be undertaken. In some instances mining costs can be reduced where an inexpensive sorting system to eliminate waste is combined with a less selective and less costly mining method. This is particularly true in deep mines where hoisting capacity determines the rate of extraction and sorting is performed underground, with waste utilized for fill. Hand sorting, while efficient, is expensive because of low sorting rates. Peale (1) quotes man hour capacity at 1/3 ton per hour on sizes 3/4" to 3" copper ore, and up to 5 tons per hour on rich iron ore sized from 4" to 16".

Jan 1, 1974

A symposium on the health hazards of respirable dust in the mining and milling of talc was held on May 8, 1973, in Washington, D.C. The results of medical effects on both human and animal subjects were presented. Methods for identification and classification of talc minerals were also presented. Analytical techniques discussed included X-ray diffraction, scanning electron microscope observation, electron probe, and optical microscopy.

Jan 1, 1974

By R. F. Stewart

A nuclear meter based on measurement of prompt capture gamma rays is being developed for monitoring the sulfur content of coal streams. Equipment has been built to measure sulfur rapidly, and methods have been devised to compensate for changes in moisture, ash, and bulk density of coal flowing through a bin. Pilot plant tests of the system with various additives to different coals show a precision and accuracy of 0.02 percent sulfur and 0.04 percent sulfur, respectively. Based on these results, a hardwired meter has been fabricated for testing in a commercial coal preparation plant.

Jan 1, 1974

By R. Feenstra

In the course of time, an increasing number of investigations on jet cutting all kinds of material, such as rocks1, 2, 3, metals4, 5, and wood6 have been reported to serve various applications. This paper deals with one particular application of jets, viz deep-well drilling for hydrocarbon exploration and production. A number of papers have been published on this subject 7, 8, 9, some of which refer to jets purposely containing abrasives, termed 'jetted particle drilling'7. Since such abrasives complicate fluid handling considerably and do not appear to be absolutely necessary for making hole we have restricted ourselves to conventional drilling fluids. A large part of our investigation has been performed with the aid of three laboratory-type drilling machines, which permit tests on both micro-bits (12 in) and full-scale bits (62 - 9 5/8 in). In view of the application of jets in deep wells, care has been taken to simulate hydrostatic pressures as they exist in the field on the hole bottom. These have been found to have a major effect on the bit-penetration rate for various drilling fluids. Following experiments with single nozzles, laboratory bits have been designed, improved further and developed for field use. Field runs on 9 5/8 in bits, using conventional equipment and pumps, served to verify the feasibility of the jet drilling concept. Further efforts are evidently needed to evaluate the jet drilling method. It is encouraging that one of these10, a field test programme, is supported by a number of oil companies jointly. Such a combined effort is of paramount importance to evaluate and develop this new method of drilling to its full potential in a reasonable period of time. This paper aims to contribute to that ultimate goal.

Jan 1, 1974

We have been exploring for minerals in Australia for over 100 years and our methods are constantly improving - but why do we pros- pect? Is the effort justified? Obviously the main motive is economic gain. It is now and always has been but conditions are changing rapidly. Once it was the prospector who could cash the nugget. Then it was the syndicate, the small company, an amalgamation of small companies, the large company, the corporation; the multinational corporation - where do we go from there? Early there was personal satisfaction and excitement in out-door activity which gave scope for individual energy, hope and in some cases reward. There still remains the satisfaction, either individual or corporate that a mineral discovery creates new wealth and makes a contribution to the nation's well being. Parallel with developments has always been the growth of restraints on exploration, frequently out of phase with the current mineral developments - miners' rights, licences, titles, royalties, mining laws and regulations, taxation etc. As the operations have become more complex so the restraints have become more confining until it is now very necessary to question whether the chances of economic gain justify the risk and responsibility of mounting costly mineral exploration leading-to extensive capital development.

Jan 1, 1974

The purpose of this study is to develop designs to facilitate and accelerate auger rotation stoppage (and auger rotation start up so as to promote auger disengagement during auger miner repositioning) and to provide a time delay and warning signal prior to auger start up to permit any miner s near the augers to get away from the augers before they start rotating. In the underground coal mines in the U.S., there are four auger miners that are currently in use. They are the Jeffrey 100L (see Figure 1-1) and 100M (see Figure 1-2), and the Wilcox WCM and the MK20A (see Figure 1-3).

Jan 1, 1974

Statistics show that despite a low lost-time accident rate there is a high fatality rate from falls of ground in pillar extraction work. Investigation of accidents indicates that in many cases the planned ex- traction cycle has been ignored. Better training, supervision, and personnel protection and where possible changed systems are suggested as a means of improving safety and achieving better Results.

Jan 1, 1974

The development of the Moura Coal Preparation Plant is described, commencing with the first'stage of the plant commissioned in 1963. The subsequent expansion stages are traced through to October, 1973. The plant has undergone frequent stages of expansion and modification and this process is continuing. The development programme for 1974 is described as proposed in late 1973. The characteristics of the Moura and Kianga field coal seams with respect to washability are summarised and some comment is made on the blending of these coals prior to washing, to ensure production of export grade coal within specification.

Jan 1, 1974

By D. J. Oswald, J. G. Ziegler

It is of common knowledge that loading within a grinding mill, whether ball, rod, pebble, or autogenous, is directly related to the lubrication back pressure developed between the mill journal and bearing shoe during mill operation. The merits of both forced-feed and gravitational-feed bearing lubrication methods are discussed with particular emphasis directed toward their applicability to continuous grinding mill inventory control. Data obtained from wet grinding mill applications in the cement and mining industries is presented to more clearly define the influence of such variables as feed consistency, slurry viscosity, mill retention, bearing oil temperature, grind fineness, and grinding media wear on the measured journal lubrication back pressure during automatic mill feed control. Finally, various grinding mill control schemes for maintaining constant mill loading and consequently optimizing mill operating efficiency are discussed and evaluated as to their advantages and/or disadvantages.

Jan 1, 1974

By Abbas Ali Daneshy

A study of the mechanics of hydraulic fracturing shows the fracture initiation pressure to be a function of the in-situ principal stresses, the formation and fluid properties, and how the wellbore has been completed. The orientation of the hydraulic fracture is perpendicular to the least in-situ principal stress. The geometry of the induced fracture depends on the treatment fluid properties, the injection rate and volume, fluid leak-off and formation properties.

Jan 1, 1974

By William G. Schultz

Sylvite of Canada, a division of Hudson Bay Mining and Smelting Co., operates a new 8500-tpd potash mine ten miles northeast of Rocanville, Sask. This mine, employing less than 60 men in its underground maintenance, engineering, and production operations probably ranks as one of the most highly mechanized and automated mining operations in the world. Access to the flat lying potash bed is through two 16-ft-diam concrete and steel lined shafts 3300 ft deep. The backbone of the operation is two 258-ton, 1500-hp continuous mining machines capable of mining in excess of 700 tph per machine while employing extensible conveyors for haulage. This production capability is complemented by a completely automated haulage, storage, and hoisting system. Of the other unique features of this operation, the principal ones are that the mine was designed and developed by the people that are currently operating it and from the time the shafts were commissioned, the mine was completely developed, equipped, and brought to full production in less than six months.

Jan 1, 1974