Search Documents

By Lloyd A. Morley, Robert Stefanko

A major difficulty encountered during the research was that nation¬al countries (almost world-wide) are in the process of revising their electrical hazard reduction standards. Their principal goal is to align their standards with the International Electrotechnical Commission (IEC) Recommendations Publication Series 79. (31-37) Additionally, CENELEC is requiring all Common Market countries to harmonize their standards. (85) However in the coal mining industry some hazard re¬duction techniques are not being accepted because some systems may not be applicable. Therefore, past literature might not directly relate a country's current feeling about explosion-proof standards. An authority in the United Kingdom (which has been a leader in hazard reduction mainly through work at the Safety in Mines Research Establishment) brought up an additional point. (15) He hopes that since revising British standards BS229 into BS4683, with the intention of corresponding with the IEC 79 series, the recent CENELEC harmoni¬zation process will also follow IEC. (8, 9, 10) The past trend in other major Common Market countries prior to CENELEC's requirement results in the authors' speculation that the standards will be pattern¬ed after the IEC Publications. (5,17,60,84,102) Several letters were sent to the East Block countries but, disa¬ppointingly, replies were dispatched only from the USSR and Poland. Recent Polish standards (1973) were received, and a very close match to the IEC Publications has been noted. (76,77) Because of their economic community, it is extremely logical to assume that the East Block stand¬ards are therefore in concurrence with the IEC. Japanese specifications also appear to be compatible with the IEC Recommendations. (42,43)

Jan 1, 1974

By Lloyd A. Morley, Robert Stefanko

Before going directly to the analysis, it would be good to summar¬ize explosion-proof container approval methods. Both Magison (52) and Short (84) state that in general practice, the systems are certified for: 1. a rugged enclosure able to withstand an internal explosion but not allow explosively hot gases to escape, and 2. maximum surface temperature, with equipment operating inside, that will not ignite the surrounding atmosphere. Also, testing insures that any material in contact with the container surface will not be ignited by a hot spot. Associated with the first practice, the enclosures are inspected for: 1. a safe flange gap width, 2. a pressure increase during ignition, and 3. an hydrostatic pressure withstand level. The hydrostatic pressure level is almost always determined by a meas¬ured ignition-pressure test and is usually applied to prove the mechan¬ical design to some safety factor. Consequently, explosion-proof enclosure testing includes temper¬ature, permissible flame gap, and pressure. Specifications and prev¬ious research also can be similarly separated even though some interre¬lation exists between the flame gap size and internal enclosure pressure during an explosion. The Schedule 2G Sections applicable to these subjects are: 1. 18.2 Definitions; 2. 18.6 Applications;

Jan 1, 1974

By Everett A. Sondreal

Material and energy balances for stockpiled lignite were calculated by computer simulation techniques to determine the occurrence of spontaneous heating. Data on properties of lignite which affect spontaneous heating were required. In some cases, best values from reported data were utilized; in other cases, new data were developed. These include specific studies on the rate and conditions that influence oxidation, heat of oxidation, heat of wetting, specific heat, thermal conductivity, and permeability of stockpiles to air. These data are presented and discussed in detail for possible application to other studies. Results of computer simulations confirm past field experience on the storage of lignite containing as-mined moisture, and predict a greater risk of heat occurrence in stockpiles of dried lignite where experience is lacking. Successful storage was predicted for dried lignite of 20 pct moisture content, if it were cooled after drying and compacted to an interparticle void fraction of 9 pct (bulk density of 67 lb/cu ft) compared to 10 pet void fraction (72 lb/cu ft) for as-mined lignite.

Jan 1, 1974

By Donivan L. Gordon

One of the several problems facing society today is that of disposing of its solid waste. Each year this nation spends approximately 4.5 billion dollars to collect, transport and dispose of some 360 million tons of domestic and industrial solid waste. Although considerable sums of time and money have been spent in researching various techniques for solid waste disposal, it is presently agreed that sanitary landfilling represents the most economic and universally adaptable solution to the problem of solid waste disposal. However, regardless of the factors favoring sanitary landfilling as the waste disposal method of choice, it should be recognized as carrying with it a potential for the degradation of ground- and surfacewater resources. Through an interdisciplinary effort regulations were promulgated during 1971 in the State of Iowa to govern sanitary disposal projects. Consistent with a set of rationales developed to preserve environmental quality, these regulations set forth hydrologic and geologic standards designed to protect Iowa's water resources. Minimum requirements have been outlined in the regulations through which the natural favorability of potential landfill sites may be evaluated. Natural favorability is primarily defined in terms of the hydrologic and geologic relationships between a proposed landfill site and those in the locality of the site. The regulations specify that leakage from a landfill to a subcropping aquifer must be less than 0.04 cu ft/day/sq ft at the base of the landfill. This factor is offered to quantify the maximum allowable leakage for all sites in unconsolidated sequences underlain by subcropping bedrock aquifers, Based on groundwater research in Iowa, the assumption is made that 50 feet of till will be sufficient to inhibit the downward flow of liquids from a landfill into bedrock aquifers. This assumes a difference of no greater than 40 feet in hydrostatic head between the water table in the unconsolidated sequence and that in the bedrock aquifer. Owing to the fact that bedrock aquifers in many areas of the state are mantled by less than 50 feet of till the regulations provide for site modification, through engineering, to meet the specified leakage standard, In such instances the leakage factor is evaluated by means of the generalized Darcy's Law Q = PIA where:

Jan 1, 1974

By J. Astier

The idea of using only one strand for both sintering and cooling of the sinter is not new. In 1952, in the U.S.A. a sintering plant was built at Benson Mine (Star Lake, N.Y.), including : - 68 m2 or 735 sqft (8 wind boxes) for sintering, - 22 m2 or 237 sqft (3 wind boxes) for cooling. In the USSR, a large number of machines have been built allowing for cooling of the sinter on the strand, especially the 4 m (about 13 ft) machines, with : 252 m2 sintering grate area 60 m2 cooling grate area 312 m2 total grate area. However, such ventures did not prove very successful, and the IRSID embarked many years ago on a research program to discover : - what are the problems associated with cooling on a sintering strand ; - what are the possible solutions for industrial plants.

Jan 1, 1974

A form of wet pelletization is described where the bridging of the individual particles is achieved by a second liquid phase that pref- erentially wets the suspended solid particles. The phenomenon can be used to obtain efficient separation of solids from carrier liquids, to form spheres from finely divided solid materials, and to separate selected constituents from a body of mixed solids. Typical examples of each of these applications are presented.

Jan 1, 1974

By William N. Poundstone

Since World War II, when off-track mining became popular, mining machinery has undergone much change. However, the change has been basically to make the machines more powerful, more productive and more reliable. Little change has been made, in this period, in the basic mining system. While steady improvement was made in productivity until the passage of the new Federal Coal Mine Health & Safety Act, I believe that the cost Co benefit ratio of further improvement from this basic approach of improving the existing extractive tool is not as promising as I believe may be obtained from a new approach. Consequently, six years ago Conoco and Consol undertook a comprehensive long-range R&D program to see if improvements of a more basic nature could be made in underground mining. We concluded early in our program that while many things currently limit the rate of production such as the rate at which roof can be supported, time needed to advance ventilation systems, time required to clean up and rock dust, time required to maintain and service equipment as well as time lost due to haulage deficiencies, that the key to improvement was a truly flexible continuous high capacity haulage. With face equipment in use today, mining rates can be increased with such a haulage system where the ability to support the roof exceeds the ability of conventional haulage equipment to remove the coal. More importantly, if we could develop such a system, it would set the stage for development of far more sophisticated methods of mining at the face than exist today, and as new and more dependable mining machines and methods are developed, continuous transportation will enable the gains envisaged in production to be realized.

Jan 1, 1974

The capabilities of the three 61R and one 81R Robbins Raiseborers currently in use at Mount Isa are defined. Their applications in the development of ventilation and hoisting shafts, orepasses, escape routes, fill passes etc. are described and possible future uses of these and newer raiseborers at Mount Isa are examined. Problems associated with the use of raiseborers, together with ways of overcoming them are discussed. The impact of raiseborers on the mining operation is assessed in terms of new approaches to design and development, safety, cost and manpower efficiencies.

Jan 1, 1974

By Ronald D. Hill, Elmore C. Grim

Surface mining drastically alters the ecological characteristics of the area disturbed and in some cases has a decided effect on surrounding areas. Vegetation is removed, topographic features and characteristics are changed, and the original geologic overburden profiles are destroyed. Spoil banks generally are a heterogeneous mixture of rock fragments, rock particles, and soil-sized material derived from the overburden strata. With proper mining techniques, the various strata can be partially or completely segregated. Segregation of over- burden material offers the opportunity to bury the toxic, acid, or salt-pro producing strata under growth supporting material. In some situations, lower strata may have more desirable characteristics than surface material and can be placed near or on the surface. For example, limestone strata appear in some lower overburden profiles that have shale and/or sandstone near the surface. Also, some lower strata have higher nutrient levels that have been leached from the surface. Experience has shown that natural revegetation is a very slow process on strip mined areas. Native vegetation may not be compatible with the environment on the mined areas, for example : 1. Low nutrients in the spoil. 2. Toxic spoils (very acid or highly alkaline ). 3. Surrounding vegetation may be of the climax type and may not have pioneer- or primary-invader-type species present. 4. The seed source may be to far away from the adjacent mined areas. Early attempts to revegetate strip-mined lands with trees also proved to be unsatisfactory as they did not provide the initial ground cover required to stabilize the spoil. Erosion control with trees only may take up to 10 years before the canopies close and an effective cover is established. They are slow to form soil profiles and do not provide effective chemical pollution control until long after planting. A quick growing cover of herbaceous species is necessary to obtain quick stabilization and initial protection against erosion by reducing runoff and rain-drop splash. Vegetative cover will also build up a concentration of organic matter in the soil, which in turn will

Jan 1, 1974

By W. D. Bensema

Two different techniques were used to make measurements of the absolute value of electromagnetic noise in an operating coal mine, Itmann No. 3 Mine, located near Mullens, West Virginia. The electromagnetic environment created by 250-volt-dc and 550-and 950-volt-ac machinery in two longwall panels was measured and is reported. One technique measures noise over the entire electromagnetic spectrum of interest for brief time periods. It is recorded using broadband analog magnetic tape, and the noise data is later transformed to give spectral plots. The other technique records noise amplitudes at several discrete frequencies for a sufficient amount of time to provide amplitude probability distributions. The specific, measured results are given in a number of spectral plots and amplitude probability distribution plots.

Jan 1, 1974

By D. P. Lindroth

The thermal diffusivity above 298 K, up to 400 K and at pressures from ambient down to 10-10 torr was measured for the following six igneous rock types: tholeiitic basalt, obsidian, rhyolite, granodiorite, gabbro, and dunite. The thermal diffusivity data were obtained by the laser flash method. Extreme values range from a low of 5.3X10-3 cmF/sec for rhyolite at 383 K and 2X10-7 torr to a high of 13.4x10-3 crrf/sec for dunite at 298 K and 760 torr. Data are also included on a commercial fused silica, which was used as a standard.

Jan 1, 1974

By Russell R. McLellan

As part of an effort to develop new or improved placer mining technology in the Tertiary gold-bearing channel gravel of northern California, the Bureau of Mines conducted investigations at the old Badger Hill placer mine in Nevada County, Calif., to collect data and information regarding drilling and sampling methods and deposit characteristics. Sampling studies involved the collection and processing of 400 tons of large-and small-volume samples from drill holes, underground workings, surface pits, and blasthole rounds. A total of 355 samples averaging 2,296 pounds per sample provided reasonably accurate data for analysis of the gold distribution. These studies indicated that the bulk of the gold is within 40 feet of bedrock in stacked, lenticular zones of cemented gravel that are largely confined to the relatively narrow, meandering course of the deepest portion of the bedrock channel. Drilling studies involved the testing of truck-mounted rotary, buckett and vibratory drills, none of which proved to be a completely versatile tool for sampling quickly and reliably both consolidated and unconsolidated gravel..

Jan 1, 1974

By N. J. Keys

This paper concerns the development and application of a high throughput multi-stream photometric sorting machine developed for the South African gold mines. It is now believed that this sorter and its progeny may be found suitable for a large proportion of all possible sorting applications. A laser light source and sensitive photomultiplier are employed in a scanning system to detect light reflected from the surfaces of rocks passing through the sorting zone. Electronic circuitry then analyzes the photomultiplier signal, which represents the varying intensity of the reflected light, and produces control signals to actuate the appropriate valves of an array of air blast rejection devices to remove from the feed certain particles selected by the analyzing process. Typical throughput per machine ranges from 50 tons/hour for a-2 ½? + 1 ¼? feed to 200 tons/hour for -6" +2 ¾ " material.

Jan 1, 1974

By Parviz F. Rad

The Bureau of Mines conducted groove cutting experiments in marble, lime-stone, granite, and quartzite with a 7-inch disk cutter under a normal thrust of 7,000 lb. The values of muck weight per unit length, specific energy, cutting coefficient, and groove depth for each of these rocks were determined for groove spacings ranging from 0.1 to 4 inches, and from these results the values of optimum and critical spacing were computed" The results indicate that compressive strength may be used to predict some of the cutting characteristics of the independent grooves. Considering all the cutting characteristics, particularly those for the interacting grooves, Shore hardness, coefficient of rock strength, and torsional velocity correlate with cutting characteristics better than do other physical properties. Some of the field applications of the principles established in this report are identified.

Jan 1, 1974

By Frank A. Peters

With the current renewed interest in advancing the technology for producing alumina from domestic raw materials, revisions of previous cost estimates to provide planning data are urgently needed. Completely new cost estimates on a 1973 basis are included for four alumina-from-clay processes and one alumina-from-anorthosite process. These estimates are based on new or previously calculated material balances, recalculated heat requirements, and new equipment designs. The use of larger and more modern equipment has permitted a significant reduction in labor requirements as well as equipment costs. Chemical prices, labor rates, and utility rates typical of late 1973 are used in these cost estimates. In addition to the revised cost estimates, all 21 previously published alumina evaluations compiled by the Bureau of Mines were updated to show the effect of inflation using an inflation index and late 1973 chemical prices, labor rates, and utility rates.

Jan 1, 1974

By José Luis Lee Moreno

This paper presents a preliminary phase of a study being conducted by the Department of Geochemistry of the Consejo de Recursos Naturales No Renovables in the vicinity of the Pachuca-Real del Monte Mining District. This district is located in central Mexico, about 100 km northeast of Mexico City. It has been in operation for the past 450 years and has produced about 38 million kg of silver and about 190 thousand kg of gold. At the present it is being worked by the state owned mining company of Real del Monte and Pachuca. The rocks of the area consist mainly of Tertiary volcanics, ranging in age from early Oligocene to late Pliocene. Ore bodies are recognized as epithermal, vein type fracture fillings. The main ore minerals are argentite and acanthite normally accompanied by base metal sulphides, Gold is present in small amounts as native gold and in other minerals. Orientation geochemical studies performed on soil and rocks over known veins in the district, showed zinc to be the best indicator. Lead and silver anomalies are restricted to the immediate vicinity of the veins, mercury shows the mineralized structures only when the "C" horizon is sampled, while antimony gave erratic values. The El Chico area is about 10 km north of the Pachuca-Real del Monte district and covers approximately 400 sq km. Geological evidence indicated the possibility of an extension of the Pachuca ore bodies in this area. Results obtained from soil and rock samples from El Chico, showed several anomalous area. Detailed investigations proved these anomalies to be related to faults and fractures which in several cases have been found to be mineralized. Drilling is planned with preliminary results expected by late 1974.

Jan 1, 1974

By Alan H. Goode

Of the 15 million tons of glass discarded in municipal wastes annually, about 2 million tons pass through incinerators and can be recovered by ore processing techniques. Although the primary use for this recovered waste glass would be as cullet in the manufacture of new glass containers, this approach is not always practical because of long shipping distances, high freight costs, and high purity requirements. Alternatives to the use of waste glass as cullet would be either as landfill or in secondary products. Although glass is considered a good landfill material, it is still wasteful of potentially valuable raw materials. Secondary products that can be made from waste glass1 include a variety of industrial and construction items. As part of the Bureau of Mines' program in secondary materials recovery, the Tuscaloosa Metallurgy Research Laboratory has conducted research concerned with the development of ceramic building products from waste glass. Materials employed in this research were obtained from municipal incinerator residues fractionated in the Bureau's continuous residue processing plant, College Park Metallurgy Research center.' The studies reported herein3,4 present research results using waste glass in the formulation and production of clay bricks, not only to produce improved products, but to reduce production costs, conserve natural raw materials, and most important, to reduce manufacturing energy requirements.

Jan 1, 1974

By B. J. Moore

This publication contains routine analyses and related source data for 278 natural gas samples from 14 States. All of the samples were collected during calendar year 1973 as part of a continuous survey of the free world for occurrences of helium in natural gas. This survey has been conducted in the United States by the Bureau of Mines since 1917. In late 1965, the survey was expanded to include foreign gasfields. The analyses published herein were made by mass spectrometer and a special helium analysis apparatus, which are described in Bureau of Mines Bulletins 4862 and 576.3 Fifteen previous publications have presented the results of 10,201 gas analyses prior to 1973. The first three, Bulletins 486,4 576,6 and 617,6 contain analyses and related source data on 5,218 gas samples collected from 1917 through 1960. The other 12 publications,7 which were issued as information circulars, supplement the three bulletins and contain 4,983 analyses of samples collected since 1960. This publication is the 13th publication supplementing the three bulletins.

Jan 1, 1974

By C. Melvin Lepper

The Bureau of Mines has developed an improved earth resistivity field system which employs a novel technique for obtaining null measurements. The instrument is designed to operate reliably in high-noise environments such as those found in the vicinity of operating mines. The system consists of a low-frequency transmitter, a sensitive receiver and an external battery pack, each in its own case to provide protection from the elements. The receiver and transmitter units have self-contained recharge-able batteries to supply power to the circuitry and separate built-in battery chargers that operate on standard 115 Vac power. The system is portable and simple to operate. Measurement accuracy, reliability, and dynamic range are superior to most commercially available equipment even though less time and effort is required to make null readings. Unlike some commercial systems, long integration times are not required to enhance signal-to-noise ratio in areas of high background noise.

Jan 1, 1974

By Robert T. Langland

The Bureau of Mines, at its Denver, Colo., research center, has developed a computer program to solve nonlinear regression problems. The program is written in a general form so that, regardless of the functional relationship assumed, the unknown parameters may be evaluated by the Newton-Raphson method of iteration. Variances and covariances of the parameters are derived, based on the propagation of errors. A creep function is established from shale test data as an example of program utility. Program accuracy is compared to the accuracies of other programs in present day use.

Jan 1, 1974