Search Documents

Development of automatic fire protection systems for large, mobile mine haulage equipment was initiated under Department of Interior's Bureau of Mines-FMC Corp. contract H0122053, "Improved Sensors and Fire Control Systems for Mining Equipment June 1972 to May 1973." After successfully designing and mock-up testing an effective economical automatic fire protection system, and after having demonstrated that the system could extinguish controlled fires on 100-ton capacity haulage trucks, USBM-FMC contract 110232059 was issued in June, 1973, to conduct further development and validation testing. This report documents technical progress and activity under the latter contract. Figure 1 shows areas of the two haulage trucks that were protected by the automatic fire protection systems tested during this program. Figures 2 and 3 are composites showing hardware and schematic diagrams of the systems tested.

Jan 1, 1974

By Madan M. Singh

The use of fluid jets for industrial purposes has received considerable attention in recent years. The convening of The First International Symposium on Jet Cutting Technology1 in April 1972 devoted solely to this subject probably heralds the coming of age of this new science. It is interesting to note the emphasis in the conference towards the cutting of rocks, minerals, and soils, indicating the attention being devoted to excavation and mining. The use of water streams for mining of minerals is not new. It is well over a century since its first application.2 But its use in coal mining has been somewhat restricted over the years. In the past 30 years the U.S.S.R. has successfully used water for coal extraction, and these techniques have been examined in 15 countries in recent years. In the United States research on various aspects of the method has been conducted for over 15 years,3 but success stories from the Soviet Union,4 JapanS and Canada6 in the last 5 years has spurred greater enthusiasm. IIT Research Institute has done pioneering work in the 7-12 13-15 area of water jetting for rock and coal breakage. It has just completed an experimental study involving mining of coal with a 50,000-psi and 100,000-psi jet in a stripping operation14 under the sponsorhip of the U. S. Bureau of Mines (Contract No. HOll1789). As a complementary program the Bureau initiated a project to design a water-jet coal-mining machine (Contract No. H0133119). IITRI was a successful bidder on this competitive procurement.

Jan 1, 1974

By John D. Spencer

Research on the development of new and improved methods for the discovery and production of oil and gas and production of fluid fuels from coal continued to be the major thrust of the Bureau of Mines energy research program during 1973. Crude oil recovery from tar sands and oil shale also retained a high priority in this work. Complementing this program were numerous studies aimed at accomplishing the objective of increased energy output with greater safety and minimum harm to the natural environment. This report summarizes research objectives and results and itemizes formal publications of the Bureau of Mines on energy and related subjects.

Jan 1, 1974

By Yi-Shen Li

This report has been prepared by Lockheed Missiles & Space Company, Inc. (LMSC), under United States Bureau of Mines Contract No. H0220040 dated 21 June 1972 for the design, development, fabrication, and certification of the One-Hour Self-Rescue Breathing Apparatus (PBA). The PBA is a self-contained, oxygen-generating, CO2-removing closed-loop breathing apparatus that provides a minimum of 1 hour of breathable atmosphere during escape from a mine with a contaminated or oxygen-deficient atmosphere. This Cost-Plus-Fixed-Fee (CPFF) contract has been successfully completed in a three-phase program. The Phase I tasks included the design, development, and fabrication of prototype units developed at LMSC in accordance with the requirement of the Code of Federal Regulations (CFR) Title 30, Chapter 1, Subchapter B, Part 11 (Appendix A), and was submitted to the National Institute for Occupational Safety and Health (NIOSH) for joint NIOSH and Bureau of Mines certification testing.

Jan 1, 1974

By M. D. Aldridge

The results of a four-year research effort aimed at developing a practical and effective electronic system for monitoring safety conditions throughout a coal mine by displaying, at a central location, remotely measured parameters are described. This document reports on the design details of the sensor packages and the data processing program used in an experimental monitoring system. The results of special ventilation monitoring experiments and several sub-system considerations are also described.

Jan 1, 1974

By Anatol Wojtowicz

This research program was conducted to determine if respirable coal dust emanating from a continuous mining machine can be suppressed more effectively by a high expansion foam than by the water sprays conventionally used. A high expansion foam system was developed and tested on a continuous mining machine under actual operating conditions. The utility of the system was demonstrated. Test results tend to show that foam application is more effective than water sprays in suppressing respirable coal dust. However, because of the extreme variability of the test conditions, scatter in the sampling data, and other factors, not enough data was obtained to form a firm conclusion that foam is more efficient than a water spray in suppressing respirable coal dust. Sufficient statistical data was obtained, however, to indicate that foam is more efficient than water in suppressing total float coal dust.

Jan 1, 1974

By E. E. Buban

A self-contained breathing apparatus has been developed to provide complete respiratory protection for a miner in an irrespirable atmosphere. The apparatus has the desired features of comfort, reliability, maintainability, and quick-donning capability. The apparatus is packaged in a moistureproof envelope and is protected in a shock absorbing, fiberglass resin carrying case. The apparatus is a small, lightweight, one-time-use device that can be readily worn on a miner's belt, requires no maintenance and is designed to have a shelf life of five years and a carrying life of three years. It is deployed to the use position in a period of 15 to 30 seconds. Man tests conducted in-house and at the National Institute of Occupational Safety and Health (NIOSH) testing laboratories established that this unit meets all performance requirements listed in the Code of Federal Regulations, Title 30, Part 11, Subchapter B, Subpart H (CFR 30, Part 11) for respiratory protective devices. The unit, which has received joint approval (TC-13F-37) on a prototype basis from the Mining Enforcement and Safety Administration (MESA) and NIOSH has: (1) Ten-minute service life under escape conditions. (2) Thirty-minute service life when the wearer is at rest. (3) Peak-to-peak breathing resistance of less than our inches water column height. (4) Inspired gas temperature of less than 135°F. (5) Breathing gas contents greater than 19.5 volume per cent of oxygen and less than 2.5 per cent carbon dioxin. (6) A weight (complete in carrying case) of 2.75 lbs. (7) A carrying case size of 6-1/2"x 5-1/8"x 3-1/8".

Jan 1, 1974

By L. D. Hartzog

A pilot plant investigation of a semi-autogenous mill - ball mill circuit is described. The plant was operated with minus eight-inch diabase as feed material to the semi-autogenous mill. The semi-autogenous mill recycle screen underflow was put to a ball mill in closed circuit with a cyclone. An operating Work Index of 13.3 to 14.9 was obtained with the pilot ball mill. This Index is substantially in agreement with the scalped feed laboratory Work Index for 15.3 for recycle screen underflow. The Bond Index of the diabase was 15.8. Thus, one may use the scalped feed laboratory Work Index to size semi-autogenous grinding plant ball mills.

Jan 1, 1974

By C. Daniel Kealy

Dissolved and suspended solids are present in the free water of tailings ponds. This Bureau of Mines study was designed to identify the influences of the slime zone in preventing these solids from reaching the environment outside the tailings pond. The finite-element method was used to determine the rate of discharge of subsurface water from the Van Stone tailings pond in northern Washington. The slime zone was sampled and tested for the first time, and results were interpreted and incorporated into the mathematical model. Computer results were verified by installing and monitoring piezometers in the field and by a simulated (16- by 1/2- by 3 foot) laboratory model. Output from the numerical model defined critical seepage zones and revealed that proper pond design and maintenance can reduce pond seepage losses to a minimum. Minimization of seepage requires maintaining the pond water level over the slime zone. Sufficient physical, chemical, and limnological data were collected and analyzed to conclude that the only realistic reflection of synergistic effects is obtained by study of the indigenous biota in combination with quantitative chemical and physical data. Proper planning and management of the milling and waste disposal operations are the key to minimal pollution.

Jan 1, 1974

By W. E. Foreman

A mathematical model was developed to assess the costs for reclamation of surface mining using the shovel overcasting operation, the front end loader operation, and a backfilling operation. A literature review was made of the present laws in Kentucky, Pennsylvania, Virginia, and West Virginia pertaining to surface mining and of the various parameters that influence the input data for a mathematical model. It was determined that the working mathematical model would have to be applied on an area to area basis, preferably on a permit by permit basis in the area where surface mining was being done. To this end, a flexible model was developed with input data obtained from the area of study. The results of the study show that the cost per ton of coal for reclamation can be estimated for various reclamation levels. Validation of the model was done for selected permits from Virginia. It was determined that the permits could easily be used for input data to the model.

Jan 1, 1974

The Federal Coal Mine Health and Safety Act of 1969 limits to 2 milligrams per cubic meter (for dust containing a maximum of 5% quartz) the average respirable dust concentration to which individual miners may be exposed. Section 205 of the Act directs that an appropriate exposure formula for dusts with quartz content in excess of 5% be established. This formula, entered in F. R. Document 70-12351 filed September 16, 1970, is 10 milligrams per cubic meter divided by % quartz. Thus, the total respirable dust exposure permitted limits the quartz to a maximum of 100 micrograms. For example, if % quartz is 5%, 10 mg/5 = 2 milligrams, and (.05) (2 mg) = 100 micrograms. Similarly, if % quartz is 10%, 10/10 = 1, and (.10) (1 mg) = 100 micrograms, etc. If the % quartz is less than 5%, the 2 mg/M3 limit prevails.

Jan 1, 1974

Two different techniques were used to make measurements of the absolute value of electromagnetic noise in an operating coal mine, Robena No.4, located near Waynesburg, Pennsylvania. One technique measures noise over the entire electromagnetic spectrum of interest for brief time periods. With present instrumentation, the spectrum can be covered from 40 Hz to 400 kHz. It is recorded using broad-band analog magnetic tape, and the noise data are later transformed to give spectral plots. The other technique records noise envelopes at several discrete frequencies for a sufficient amount of tine to provide amplitude probability distributions. The specific measured results are given in a number of spectral plots and amplitude probability distribution plots. The general results are that at frequencies below 10 kHz, power line noise within the mine is severe. Impulsive noise is severe near arcing trolleys, and at lower frequencies near any transmission line. Carrier trolley phone signals and harmonics are strong throughout the mine whenever the trolley phone is in operation. Additional information beyond that included in this report may be obtained from the authors, who are with the Electromagnetics Division of the National Bureau of Standards.

Jan 1, 1974

By Jose M. S. Ramos

This paper describes the slope stabilization procedure at Cauê Mine, Companhia Vale do Rio Doce - CVRD, Itabira, State of Minas Gerais, Brazil. Cauê Mine, is a large open pit, to produce about 41 million tons of iron ore during 1974, and an intensive program of investiga Lion was carried out to provide the basic data for stabilizing its slopes, The ultimate rock slope in the W area will be about 400 m high with dipping angles decreasing gradually from top to bottom of the pit. The investigations started in 1969 and since then many geologists and engineers, from both CVRD and Geotécnica S/A., assisted by international consultants, have given their contribution to the achievement of solutions. It is hoped that this paper may contribute to the slope stability of other mines in tropical climate.

Jan 1, 1974

An outline of the circumstances giving rise to the current Commonwealth-States con- flict in relation to offshore mineral explor- ation and production is set out, together with an analysis of the Seas and Submerged Lands Act 1973. The bases of the claims by the Commonwealth and the States in this regard are discussed with relation to the territorial sea and the continental shelf.

Jan 1, 1974

By Robert D. Coale

This paper will describe the copper concentrate slurry pipeline and pumping system between the concentrator and the port at Bougainville Copper Ltd. The operations of Bougainville Copper Ltd. are located on the island of Bougainville in the South Pacific. Geographically, it is the northernmost island of the Solomon Group but, politically, it is part of Papua New Guinea. Papua New Guinea is a United Nations Trust territory administered by Australia, having recently been given self-government, with independence scheduled for December 1974. (Fig. 1). The island is approximately 130 miles long by 30 miles wide, with the Crown Prince mountain range forming a spine along its length. The mountains in place are over 8,000 feet high with the mine located on the western flank at an elevation of 2,200 feet. Exploration on Bougainville for copper by Conzinc Riotinto of Australia (CRA) began in 1963 and by 1968, through geophysical, geochemical and diamond drilling methods, an orebody containing nearly one billion tons of ore grading approximately 0.48% Cu. and sane gold had been outlined. Bougainville Copper Ltd., the company operating the mine, is 53.6% wined by CRA, 20% mined by the government of Papua New Guinea with the public Folding the remainder of the shares. The first copper concentrate was produced in early 1972, with production for the first full year, 1973 being:

Jan 1, 1974

By P. T. Brooks

A process for extracting 69 percent of the vanadium from weathered Nevada dolomitic shale containing about 1 percent V205 was developed on a laboratory scale by the Bureau of Mines. The process essentially is comprised of salt roasting, leaching with dilute sulfuric acid, solvent extraction, and precipitation of vanadium as ammonium metavanadate. Carbonaceous unweathered shale was less amenable to treatment. A preliminary cost estimate for mining and processing 1,500 tons per day of weathered shale indicated a production cost of about 1 dollar per lb of V205. Considering recent sales at nearly $1. 75 per lb of contained V205, larger scale testing to obtain more definitive process design and evaluation data may be warranted.

Jan 1, 1974

By D. D. Porter, H. G. Carlevato

Blasting to prepare orebodies for in situ leaching usually involves extraordinary conditions which sometimes require special and innovative techniques. To date several unusually large blasts have been made for leaching with results that are very encouraging. Among the factors considered when designing these large blasts are orebody shape and depth, rock properties, vibration and damage potential, loading logistics, and safety. All of these factors, and others, are discussed with an effort made to put each of them into its proper perspective.

Jan 1, 1974

By O. E. Wheeler

The term "finite element analysis" is heard and seen in print a great deal these days; a few words on what precisely it is are in order. In the broadest sense, finite element analysis is an application of an idea developed by a nineteenth century mathematician named Rayleigh. His basic idea was to decompose any problem in mathematical physics into a large number of simpler problems, solve the simpler problems, and then put those solutions together to form an approximation to the solution of the original problem. The scheme works nicely because of two features: first, much of the difficulty in solving practical problems of mathematical physics stems from irregularities in the boundaries and the simpler problems can be chosen with regular boundaries and second the smaller problems are solved for small physical areas where simple approximations of the solution do not differ much from the true solution. In the narrower sense, in which we are now interested, finite element analysis is a technique of using imaginary simple structural elements to construct analytical models of real structures. A direct parallel with the Rayleigh approach exists since the "finite elements" have simple boundaries and are restricted to simple behavior within a single element. Although the correspondence between Rayleigh's ideas and finite element analysis is now widely recognized, the computational tool, as it has developed over the last thirty years, comes not from the discipline of physics but rather from that of structural engineering. It is interesting that it came not from the traditional research community, the universities, but instead from working

Jan 1, 1974

By G. L. Hundley

An anhydrous chlorination process has been developed by the Bureau of Mines for the production of copper, ferric oxide, and sulfur from chalcopyrite. The first part of the process is a chlorination step in which elemental sulfur and a mixture of iron-copper chlorides are produced. This paper describes the second step of the process in which the copper and iron chlorides are reacted with oxygen to selectively convert the iron chloride to ferric oxide and chlorine leaving the copper in the chloride form. The chlorides are pulverized and dropped countercurrent to a flow of oxygen in a vertical 20-cm-diam. reactor at 800° C. By leaching with brine, the copper chloride may be separated from the insoluble iron oxide and reduced to copper powder by electrowinning. It has been demonstrated that 70 to 80 pct of the iron can be converted to oxide in a single-stage operation with a chlorine content in the offgas of 80 pct. After removal of the oxygen, this chlorine could be recycled to the chlorination step. A two-stage operation will convert 98 to 99 pct of the iron in the mixture to insoluble oxides. The offgas from the second stage contains 70 pct chlorine.

Jan 1, 1974

By James A. Doolittle

In the underground type of mining operation, the finer portion of the waste material commonly is pumped as a hydraulic slurry to a tailings disposal pond. (1)* The tailings slurry is deposited via a pipe manifold system located around the perimeter of the pond. This method of deposition produces zoning because the coarser material tends to settle out immediately while the finer particles tend to remain in suspension and are deposited progressively nearer the center of the pond. The manifold system must be raised periodically as the pond fills with the tailings material. Over a period of time, this procedure will produce a zoned embankment known as a tailings dam. A typical pond and dam are shown in Figure 1. In plan view, the dimensions of tailings dams can be on the order of miles, with the height of the dam reaching 100 to 200 feet. Due to such factors as inadequate compaction, inherently low strength of the tailings material, and the possibility of high phreatic surface, many dams at some point become unstable, i.e., the factor of safety against a slope failure approaches 1.0. Remedial measures are required to improve the safety factor in order to prevent massive failure of the dam. In most cases, stability can be improved by effectively flattening the slope of the dam as shown in Figure 2, but this is not possible in every case. Occasionally, a tailings dam is constructed adjacent to a natural or legal boundary so that it is not possible to construct a conventional berm or to reduce the slope angle with earth moving equipment. Even a terracing process would require removal of the material and this may not be practical. In such a situation, an alternate scheme to improve stability must be found.

Jan 1, 1974