Search Documents

By C. B. Manula, H. Gezik

In planning modem-day mining operations, management needs to pass from the area of subjective decision-making to an area of objective decision-makirlg. Planning procedures currently being practiced by many mine managers depend primarily on common sense and trial-and-error methods which oftentimes never reach optimum solutions. For this reason, an attempt is made to provide an understanding of linear programming to solve production planning problems. More specifically, a linear programming model is proposed to solve the production scheduling problem as it was found to exist in the crushed stone industry. Optimal production scheduling is of prime concern here, since the industry has to cope with seasonal demands for its products. The solution, as determined through the application of the model, provides management not only with an optimal production schedule but also with the following information regarding the improvement of existing facilities: (I) the location of bottlenecks which limit production and profit; (2) the directions in which the company i fixed equipment should be expanded or modified; and (3) the evaluation of unused resources. Future trends in stone production will quite likely parallel those in the construction industry. Continued record expenditures for structures such as dams, highways, and buildings are the reasons for this accelerated growth. Production forecasts for the next decade are predicted to be around one billion tons with an approximate 7% annual increase. The problem of increasing production from 570 million tons in 1966 to 1 billion tons by 1976 offers no small challenge. This situation is further compounded by other problems and economic factors. Population expansion, government regulation, labor agreement, and changes in technology wd cause managers and operators to be confronted by many more complexities than characterize present-day operations. Some of these. problems and economic factors are: (1) In some metropolitan and other urban areas, easily accessible sources of stone are almost depleted. Transportation costs will be a prime concern of the industry. (2) Population growth has forced residential expansion to a point where many quarry operators must conform to urban and suburban regulations. (3) Government regulation in regard to air and water pollution, noise, and reclamation as well as zoning developments necessitate that crushed stone producers keep abreast of changing conditions and requirements. (4) The crushed stone industry operates under pressure of a highly competitive situation. Every company's objective is to retain a favorable marketing position by exercising great attention to production and marketing costs. This is rather difficult, since the crushed stone industry is one segment of modern mining which has to cope with a seasonal demand for its products. Among the problems posed here, the one of exercising great attention to production and marketing costs is of current interest to management. Under seasonal demand conditions, this problem creates further difficulties for managers who need to plan and forecast. STATEMENT OF THE PROBLEM Various methods of Operations Research have been developed to handle a problem whose genesis is explained above. It is very seldom, however, that these quantitative means are used in practice by the mining industry. This paper describes the use of Operations Research methods to solve a production planning problem when demand is seasonal. The seasonal production planning problem is an important one because of the substantial costs associated with changing production, employment, and inventory levels to adjust to seasonal sales patterns. Most companies try to operate within reasonable levels of employment changes and hold inventories within storage capacities. In general, little or no attempts were made to develop minimum cosl schedules or to provide objective means to compare various production policies. When demand varies within a fixed time period, 11:-oduction requirements may be met by following one

Jan 1, 1970

By I. Spector, A. J. Smith

In 1967, BACM Industries Limited started producing walboard at Saskatchewan's first gypsum products plant, located in Saskatoon, using, as a basic raw material, gyp-sum rock supplied from the company's mine near Amaranth, Manitoba. This paper describes the geology of the Amaranth gypsum deposit, the method of mining the rock and the manufacturing facilities used to produce wall-board.

Jan 1, 1970

By M. N. Shetty

LARGE copper whiskers were grown from cuprous iodide by reduction with hydrogen at about 500°C. Carefully selected single-crystal whiskers of [loo], [110], and [Ill] orientations were used and the whisker shapes and cross sections are shown in Fig. 1. Spec-trographic analysis of a typical batch of whiskers showed that the composition was better than 99.9 pct with iron and silicon as the major impurities. The test specimens varied from about 70 to 400 u in diam and they did not show a conspicuous yield drop as observed in very fine whiskers (diam <25 u), tested by Brenner.1 The characteristics of the stress-strain curves were similar to those of bulk single crystals, even though the maximum flow stresses reached in some orientations were comparable to the yield stresses observed in fine whiskers. Mechanical properties of whiskers of different materials and copper whiskers up to about 100 u in diam have been reviewed,&apos; and a mechanism of slip band propagation in fine whiskers has been recently suggested.3 Whiskers in this work were tested in a floor-model Instron testing machine using low strain rates. (Details of the testing procedure, diameter dependence of the yield stress, and the characteristics of the load elongation and stress-strain curves have appeared esewhere.4) Due to the extensive deformation, >50

Jan 1, 1970

By Freeman Bishop

The Interior Department has been in a state of disarray for many months. At first this was attributed to Interior Secretary Walter Hickel&apos;s inability to anticipate how his words would be interpreted by Press-Radio-TV. But then the already disquieted ernployees in the Department became aware that plans were afoot to take bits and pieces of the various antipollution programs from Interior; Health, Education and Welfare: the Atomic Energy Commission and other agencies and lump them together into a new Federal agency. Interior, many predicted, would be a shell of its former robust self. Hardly had this rumor started to add to employee uneasiness before the other big shoe hit the floor. The new rumor had it that the Bureau of Mines was being stripped of most of its research functions and that the Office of Coal Research and allied research groups would be abolished altogether.

Jan 1, 1970

By Roland W. Rammler

In recent years, the crude oil reserves of the world have increased at the same rate as the consumption. A Consideration of the global figures suggests that adequate supplies of petroleum will be available during the next decades. On the other hand, it in a fast of economic and political significance that the reserves in the industrialized countries increase much more slowly than in the developing countries. In Western Europe the reserves have even decreased. At the present time, about 70 % of the petroleum reserves of the world are in the Middle East and in Africa in regions in which political arises are prevalent or impending. For the industrialized countries, the discrepancies between the consumption and reserves in various regions of the world are a strong urge to investigate whether oil can be recovered from other sources. The situation will probably not be changed to a large extent by the discovery of oil in the north of Alaska. The main starting materials for the production of synthetic crude oil are coal, oil shale and tar sand. In North America, where the consumption of petroleum increases more rapidly than the reserves, there are enormous deposits of each of the three materials. This fact is another incentive toward the utilization of these unconventional oil reserves, which provide a reliable basis for a supple of energy for a long time to come.

Jan 1, 1970

By Ashok K. Sinha

During the course of an in~*estigation into the occurrence of ordered AB3 structures, the following new phases have been found —CrRh3 (AuCu3 type), CrCo3 (MgCd3 type), HfCo4 (Ths Mn23 type), and WPt, MoPh type). The composition of the TiPt3-x phase (TiNi, type) is close to Ti23Pl77. The alloy chenzistry of transition rnetal AB3 structures is rezliewed in the light of electron concentration correlations of hex-agonality recently obtained for quasi-binary alloys. The relatizte colurne contraction in the AB3 structures increases with increasing difference in volume of the conzponents. A family of ordered close-packed layered structures is formed by stacking identical layers of composition AB, in various sequences, such that the coordination is twelvefold throughout and there are no A-A contacts. Previous work&apos; on quasi-binary AB3 alloys has led to the conclusion that the stacking sequence of the AB, structures changes with increasing radius ratio RA/RB from a purely cubic, through different mixtures of hexagonal and cubic stacking to a purely hexagonal stacking. However. for binary AB3 alloys, a correlation between the type of the crystal structure and the position of the components in the various volumns of the periodic table has been noted.2-5 It has been noted6 that this correlation appears to hold even though the radius ratio RA/RB may vary over a considerable range with the location of the components in the three long periods. Another study7" of several quasi-binary systems led to the conclusion that an increase in hexagonality of the stacking is associated with increase in the electron concentration e/a. as defined by the average per atom of the total number of electrons outside the inert gas shells. In apparent conflict with this conclusion, it is known that seven binary alloy structures isotypic with TiNi3 which is 50 pct hexagonal occur at a higher electron concentration (e/n = 8.5) than that (e/a = 8.25) for the 100 pct hexagonal MgCd3 type structure present in seven binary AB3 alloys. Table 111. In the present work, an investigation into the occurrence of binary AB3 structures in transition metal alloys was made, and a survey of binary AB3 structures is presented. EXPERIMENTAL The starting materials were pure metals of 99.9 wt pct purity. The alloys were arc-melted under partial pressure of argon and annealed in sealed silica capsules lined with molybdenum foil under argon at- mosphere. The total weight loss upon melting and subsequent annealing was always less than 1 pct and hence the alloys will be referred to by their intended (unanalyzed) compositions. Wherever the constitution permitted. the alloys were given a homogenizing treatment at 1200°C (3 days) prior to annealing. Unless otherwise stated all alloys were annealed at 900°C for 1 week and water-quenched. Sometimes the final annealing treatment was carried out on powders to accelerate the attainment of equilibrium. X-ray powder patterns were taken using a Guinier-de Wolff focusing camera (CuK, radiation) or an asymmetrical focusing camera (Co or CrK, radiation). For lattice parameter determination. internal silicon standards were employed. The intensity calculations were made using a Fortran IV program written by Jeitschko and parthe.9 RESULTS Twenty AB3 and three AB4 alloys were investigated. Table I lists the crystallographic data on some of the intermediate phases encountered in the present work. Table II contains the X-ray data for HfCo, (Th,,Mn,, type). The positional parameter, x. was assumed to be 0.378. the value for Th6Mnn2310 The X-ray pattern of ZrCo, was very similar to that of HfCo, and the previous structure determination of ZrCo, by Kuzma el al." was confirmed. Ordering in the alloy CrCo could be ascertained by the presence of only one weak super lattice line (101). the others being too weak presumably owing to the small difference in the scattering powers of chromium and cobalt. This line was observed in the X-ray pattern of powder from the massive sample annealed at 830°C (7 days) after the powder had been reannealed at 600°C (24 hr). The diffraction pattern of the powder similarly reannealed at 830°C (24 hr) contained only the lines due to a mixture of hcp and fcc Co(Crj solid solutions. Therefore, it appears reasonable to assume that O2 and/or N2 contamination which would be less likely to occur during the 600°C anneal was not responsible for the observed weak reflection. Also. this reflection cannot be identified with any of the strong lines of the neighboring s phase which is present in the Co-Cr system at higher chromium contents. The composition corresponding to the TiNi3 structure observed by Raman et al.12 in the two-phase alloy Ti,zt,, has been established in the present work as being between There was satisfactory agreement for the low-angle lines (up to d = 1.997A) between the observed diffraction pattern of TiCua and that calculated assuming the ZrAu, structure. as recently proposed by Pfeifer-et a1.I3 However. some of the superlattice lines. e.g., at d = 1.937 and 1.919A. predicted by the ZrAu, structure were not actually observed eve? though neighboring lines. at d = 1.947 and 1.986A. of comparable calculated intensity were present. The ZrAu

Jan 1, 1970

By Samuel S. Adams

Economic concentrations of potassium are essentially limited to thick, stratigraphic sections of marine evaporites. These deposits were precipitated through the evaporation of sea water in restricted epicontinental seas or in grabens related to continental margin rift systems. Following deposition the deposits were subjected to diagenesis and varying degrees of metasomatism and structural deformation. The origin and characteristics of potash deposits are easier to study and interpret than those of most ore deposits because the phase chemistry of the salt systems is known and the approximate composition of the ore-forming fluid (sea water) can be inferred with confidence. It is particularly helpful that the temperature and pressure of deposition approximated that of present earth surface conditions and the pertinent mineral assemblages can readily be duplicated in the laboratory. The study of these comparatively simple salt deposits provides examples of the practical advantages of understanding the genesis of an ore deposit. These observations, in turn, illustrate the importance of pursuing research on the more complicated magmatic, hydrothermal, and ground-water systems as a means to the more successful exploration for and exploitation of the deposits they have produced. It is the purpose of this paper, therefore, to discuss certain aspects of salt deposit geology as they contribute to exploration and mining through some understanding of ore formation. References to field examples and chemical relations in the salt systems are brief. All examples are more fully discussed, however, in the references cited.

Jan 1, 1970

By A. T. Yu

Bulk sampling is define&apos; as the ?process of extracting a small fraction of material from a large bulk ...sufficiently representative ...for the intended purpose.? (ref. 1). Today&apos;s pressing need for simple, effective and reliable sampling systems is intensified by the growing demand for quality control as a means to cope with inflation, competition and rapidly increasing consumption of raw materials. Much has been written on bulk sampling (ref. 2 thru 9). It involves a wide range of subjects cutting across the domains of physics, chemistry, geology, mining, materials handling and processing, as well as probability and statistics. Since the problem itself is complex, any in-depth treatment cannot avoid a somewhat lengthy coverage. Of all of the related topics. Arbitrary, haphazard studies, on the other hand, can leave out important details and obscure or confuse the issue.

Jan 1, 1970

By Earl R. Hoskins, James E. Russell

The electrical resistivity of rocks has been studied quite extensively, in particular, the effects of temperature and confining pressure on resistivity. References 1 through 6 at the end of this chapter pertain to electrical resistivity of rock and contain further references on the same topic. The present study is motivated by an interest in determining the in-situ properties of rock as well as the stress state of the rock and how these quantities are changing with time. Most of the previous work on the electrical resistivity of rocks has been directed toward saturated rocks at relatively high confining pressures and temperatures. The present study was oriented towards air-dry surface rock that might occur in mine pillars. The mean stress and temperature under such conditions are comparatively low. It has been demonstrated that the resistivity of rock is highly dependent upon the porosity. In fact, for saturated rocks, a relationship referred to as Archie&apos;s law has been established between porosity and electrical resistivity. In the case of saturated rock, the property that is actually being measured is the resistivity of the solid/fluid system. Since the resistivity of the fluid alone is usually much lower than that of the dry rock, it is understandable that the resistivity of a saturated rock is in general several orders of magnitude lower than the resistivity of a relatively dry rocli. For dry rock, it seems reasonable that the electrical resistivity should increase as microcracks open within the material. Since microcracks open as material is stressed closer and closer to its failure point, it appears that there should be a correlation between electrical resistivity

Jan 1, 1970

By Freeman Bishop

The House Ways and Means Committee recently heard a bitter dispute over whether gasoline with lead is a worse pollutant than gasoline without lead. The lead industry is also squarely in the middle of this dispute for obvious reasons. Lead used in gasoline amounts to 270,000 tpy, or more than 254 of the annual total mined in the U.S. Few industries can face the loss of such a market without wondering how they are to stay in business. The lead industry picked up unexpected support in this dispute, however, when the AFL-CIO stepped up with outright opposition to the President&apos;s proposal to tax lead in gasoline.

Jan 1, 1970

By W. J. Maraman, D. R. Harbur, J. W. Anderson

A device for rapidly quenching liquid metals into thin platelets has been developed at the Los Alamos Scientific Laboratory. This rapid quenching equipment is built around the technique of catching a molten drop of metal between a rapidly closing plate and a stationary plate. The design and operation of this unit are described. The closing speed of the smasher plate at impact is 12.6 ft per sec. The quenching rate for this device is controlled by the interface resistance between the plates and the platelet, and is dependent upon the heat content and density of the material being quenched. The initial quenching rate down to the freezing point of the platelet material is lo5º to 106ºC per sec. After an isothermal delay, which is poportional to the heat of fusion of the platelet material, the final cooling rate down to the temperature of the smaslier plates is l04ºto 105cº per sec. RAPID heating of metals by capacitor discharge and other methods has provided the metallurgist with a useful tool for probing into the kinetics of phase changes and the many nonequilibrium phenomena which occur during rapid temperature changes. Equally interesting studies can also be made on metals and alloys which are rapidly cooled from the liquid state.&apos; Studies in this field have been limited, however, because the rates at which metals could be cooled were many orders of magnitude slower than the rates possible for heating. In recent years many new laboratory methods have been developed to rapidly cool metals from the liquid state to ambient temperature and below.2"4 All of these methods involve spreading a liquid drop of metal into a thin foil in a very short time. The methods developed have varied from ejecting a drop of molten metal at the inside surface of a rotating cylinder or stationary curved plate to catching a falling drop of molten metal between rapidly closing plates. The equipment which has been developed at the Los Alamos Scientific Laboratory for rapidly cooling molten materials uses the latter of these two approaches. The basic design, operation, and initial results of this rapid quenching device are given in this report. APPARATUS The drop smasher, which is now being used to obtain rapidly cooled metal foils, is shown in Fig. 1. Basically the device consists of a smasher plate which is driven by a solenoid into a stationary plate. The solenoid is activated by a drop passing through the photoelectric cell and is powered by discharging an adjustable 350-v capacitor bank with a 66-amp peak current into it. This power supply is designed so that the solenoid is powered for 2 m-sec after plate closure to minimize the rebound effect. There is an adjustable time-delay mechanism between the photoelectric cell and the solenoid. Both smasher plates have changeable inserts so that a variety of materials can be used to smash the molten drop. The shaft of the moving plate is guided in an adjustable housing which has ball-bearing walls. The cabinet shown to the left of the drop smasher in Fig. 1 contains the power supply and receiver for the photoelectric cell, the time delay mechanism, and the capacitor bank. The drop smasher can be placed inside a vacuum chamber, for use with radioactive materials, with the upper plate forming the lid, as shown in Fig. 2. On top of the vacuum lid is an induction coil, powered by an Ajax induction generator, which is used to melt drops from the end of the rod extending through the vacuum seal on top the quartz tube. OPERATION The drop smasher shown in Fig. 2 is operated in the following manner. The smasher plates are separated and the unit is lowered into the vacuum chamber using a pressurized cylinder. The induction coil, quartz tube, and lid with sliding vacuum seal are then assembled on top the vacuum chamber. A rod of the material for rapid quenching studies is connected to the rod extending through the sliding vacuum seal. The vacuum chamber is then evacuated and the desired atmosphere established. The photoelectric cell is turned on, and the capacitor bank is charged and armed. Power is supplied to the induction coil, and the rod of material for rapid quenching studies is lowered into the induction field. A molten drop forms on the end of the rod, drops off, falls through the light beam of the photoelectric cell, and is then caught between the smasher plates. .

Jan 1, 1970

By John V. Beall

It is difficult to understand why they did it. It was a demonstration of total commitment which sent chills of mixed admiration and fear up and down your spine. The scene was the bodega in Section A, 2660 Level on the 12 to 8 shift. The jefe was patiently waiting for the tea leaves to settle in a large metal cup. His attention was distracted by the appearance of a miner who had a problem. The long and short of it was that the miner believed the branch raise he was driving was unsafe and he wanted the jefe to come and see it. After lunch the jefe went around. First cautiously shining his light to peer up the raise from outside the chute, he then scrambled inside and swiftly climbed the cribs to the face. No question, it was hairy; about 4 crib sets were needed to catch up to the face. The unsupported raise was slabbing. It didn&apos;t take the jefe more than a few seconds to ascertain this situation and to slide back down. As he came out of the chute, a small avalanche arrived on his heels and provided a sort of exclamation point to his order; "cerrado!" In other words, shut &apos;er down.

Jan 1, 1970

By J. J. Tietien, R. O. Clough

A technique previously used to prepare alloys of InAs1-xPx and GaAsl-x Px, miry: the gaseous hydrides arsine and phosphine, has been extended to grow single -crystalline GaAs 1-x Sb x by replacing the phos-phine with stibine. Procedures were developed for handling and storing stibine which now make this chemical useful for vapor phase growth. This represents the first time that this series of alloys has been grown from the vapor phase. Layers of P -type GaSb and GaSb-rich alloys have been grown with the carrier concentrations comparable to the lowest ever reported. In addition, a p-type alloy containing 4 pct GaSb exhibited a mobility of 400 sq cm per v-sec which is equivalent to the highest reported for GaAs. RECENTLY, interest has been shown in the preparation and properties of GaAs1-xSbx alloys, since it was predicted1 that for compositions in the range of 0.1 < x < 0.5, they might provide improved Gunn devices. However, preparation of these alloys presents fundamental difficulties. In the case of liquid phase growth, the large concentration difference between the liquidus and solidus in the phase diagram, at any given temperature, introduces constitutional supercooling problems. It is likely that, for this reason, virtually no description of the preparation of GaAs1-xSbx by this technique has been reported. In the case of vapor phase growth, problems are presented by the low vapor pressure of antimony, and the low melting point of GaSb and many of these alloys. In previous attempts1 at the vapor phase growth of these materials, using antimony pentachloride as the source of antimony vapor, alloy compositions were limited to those containing less than about 2 pct GaSb. This was in part due to the difficulty of avoiding condensation of antimony on introducing it to the growth zone. A growth technique has recently been described2 for the preparation of III-V compounds in which the hydrides of arsenic and phosphorous (AsH3 and pH3) are used as the source of the group V element. With this method, GaAs1-xPx and InAs1-xPx have been prepared2&apos;3 across both alloy series with very good electrical properties. Since the use of stibine (SbH3) affords the potential for effective introduction of antimony to the growth apparatus, in analogy with the other group V hydrides, this growth method has been explored for the preparation of GaAs1-xSbx alloys. In addition to GaSb, these alloys have now been prepared with values of x as high as 0.8. In the case of GaSb, undoped p-type layers were grown with carrier concentrations equivalent to the lowest reported in the literature. Thus it has been demonstrated that, with this growth technique, all of the alloys in this series can be prepared. EXPERIMENTAL PROCEDURE A) Growth Technique. The growth apparatus, shown schematically in Fig. 1, and procedure are virtually identical to that described2 for the growth of GaAs1-xPx alloys, with the exception that phosphine is replaced by stibine.* HCl is introduced over the gallium boat to *Purchased from Matheson Co., E. Rutherford,N+J. transport the gallium predominantly via its subchlo-ride to the reaction zone, where it reacts with arsenic and antimony on the substrate surface to form an alloy layer. The fundamental limiting factors to the growth of GaAs1-xSbx alloys from the vapor phase, especially GaSb-rich alloys, are the low melting point of GaSb (712°C) and the low vapor pressure of antimony at this temperature (<l mm). Thus, relatively low antimony pressures must be employed, which, however, imply low growth rates. To provide low antimony pressures, very dilute concentrations of arsine and stibine in a hydrogen carrier gas were used. Typical flow rates (referred to stp) were about 4 cm3 per min of HC1 (0.06 mole pct)+ from 0.1 to 1 cm3 per min of ASH, (0.002 to 0.02 mole pct), and from 1 to 10 cn13 per min of SbH3 (0.02 to 0.2 mole pct), with a total hydrogen carrier gas flow rate of about 6000 cm3 per min. Although no precise data on decomposition. kinetics exist, it is known4 that stibine decomposes extremely rapidly at elevated temperatures. However, the high linear velocities attendent with the high total flow rate (about 2000 cm per sec) delays cracking of the stibine until it reaches the reaction zone and prevents condensation of antimony in the system. To improve the growth rates of the GaSb-rich alloys, growth temperatures just below the alloy solidus are main-

Jan 1, 1970

By Robert A. Rapp, Ronald L. Pastorek

Solid-state electrochemical measurements by three alternative experimental procedures were made with the cell FeO, Fe3O4 |Zro.85Cao.15O1.85 |Cu| Zr0.85CaO.15O1.85 | FeO, Fe304 to establish the solubility and diffusivity of oxygen in solid copper in the temperature range 800" to 1030°C. The solubility of oxygen in solid copper and the diflusivity of oxygen in solid copper Dgu = 1.7 X 10-2 exp(-16,000/RT) Cm2/sec were determined and confirmed in alternative experiments. The enthalpy of solution of oxygen in solid copper equals —10,000 cal per mole; the partial excess entropy of the oxygen atoms in the Cu-O dilute solution is approximately the same as that found for interstitial atoms in other metals. The diffusivity of oxygen in solid copper is consistent with that expected for an interstitial atom. RELIABLE values for the saturation solubility N(s) and diffusivity DO of oxygen in solid copper have not been unambiguously established in the literature. Following three early determinations by others,1"3 Rhines and Mathewson4 reported that the solubility of oxygen in solid copper increased from 0.007 at. pct 0 at 600°C to about 0.015 pct at 1050°C. Phillips and skinner,, using essentiially the same analytical procedure, reported that the solid solubility increases from 0.0018 at. pct 0 at 550°C to about 0.0075 pct at 1050OC. The only previous value for the diffusivity of oxygen in solid copper was reported by Ransley.6 Ransley deoxidized Cu-Cu2O alloys in an atmosphere of carbon monoxide gas to yield a solubility-diffusivity product. He used the solubility data of Rhines and Mathewson to calculate the diffusivity values. Another method for obtaining the solubility-diffusivity product (N(s) DO) is by measuring the widths of internal-oxidation zones in copper alloys as reported by Verfurth and Rapp.7 However, the calculated N(S)Do products depend upon the alloy content of the specimen, so that the internal oxidation of copper alloys does not follow ideal internal oxidation kinetics. As a result, unequivocal values for the N(s) DO product were not obtained by this procedure. A solid-state coulometric titration technique similar to that employed in this work was introduced by C. Wagner8 to study the dependence on silver activity of the Ag/S ratio in silver sulfide in the temperature range of 160" to 300°C. Similar experiments have been carried out by C. Wagner and co-workers9-11 to study the stoichiometry range of silver and copper tellurides, cuprous sulfide, and cuprous selenide. Numerous authors have carried out electrochemical measurements with a solid oxygen-ion-conducting electrolyte to determine the solubility and/or diffusivity of dissolved oxygen in several liquid metals.12-l6 Rickert and Steiner17,18 have used solid-state electrochemical measurements to determine the diffusivity of oxygen in solid silver from 760" to 900°C. Two different cell geometries were used. In the cell of linear geometry Fe, FeO | ZrO2 + (CaO) | Ag + [0 (dissolved)] [1] oxygen diffused from the interior of the silver electrode to the silver/electrolyte interface where the oxygen activity had been lowered from a fixed initial value to practically zero by the application of voltage to the cell. The diffusivity of oxygen in solid silver was determined from the solution of the diffusion equation and the time dependence of the cell current. However, this determination of the diffusion coefficient depended upon a knowledge of the solubility of oxygen in solid silver. A cylindrical geometry was used for the cell Pt, O2(Po2 = 0.21 atm) | ZrO2 + (CaO) | Ag + [0 (dissolved)] [II] which also allowed the diffusivity of oxygen in solid silver to be determined. These values were in agreement with other available data.l9 Recently, Raleigh20,21 used a method involving the measurement of diffusion-limited currents in a cell involving the AgBr solid electrolyte to determine the diffusion coefficient of silver in Ag-Au alloys at 400°C. Diffusivity values on the order of l0-14 sq cm per sec were measured in the alloy composition range 10 to 60 at. pct Ag in a single experiment. From numerous electrical conductivity and galvanic cell measurements,9&apos;22"26 the solid solution Zr0.85 Ca0.15 O1.85 has been established as an electrolyte with predominant oxygen ion conduction over a wide range of intermediate and high oxygen activities. For interrelating the thermodynamics and the kinetics of the dissolution of oxygen in solid copper in this investigation, a galvanic cell was constructed with FeO-Fe3O4 as the reversible reference electrode, the Zr0.85Ca0.15 O1.85 electrolyte, and a pure copper specimen under-saturated in oxygen as the other electrode. THEORETICAL ANALYSIS Three variations of a high-temperature electrochemical technique were used in this study to provide two determinations each of the solubility and diffusivity

Jan 1, 1970

By H. Y. Hunsicker

A graphic method has been devised for three-di-mensional analysis of hot deformation and for correlating the amount and directionality of the deformation with resulting directional properties. Deformation is evaluated in terms of dimensional change ratios referred to three orthogonal axes. Since all combinations of the three ratios can be represented in a triangular coordinate field with logarithmic scales, a two-dimensional chart of extent of deformation and degree of asymetry is possible. The entire gamut of shape changes from upsetting through flat-rolling to rod-rolling is accommodated. The resulting coordinate system is a base upon which can be represented the properties of the wrought products measured in the directions of the axes employed fir evaluating the deformation. When property data are available for many types and amounts of deformation, a three-dimensional figure can be constructed, and the projection of this figure is referred to as a &apos;&apos;3d&apos;&apos; chart. Experience in using such charts to plan fabricating operations for a variety of thick-section forged and rolled products of heat-treated aluminum alloys has verified its practical value for optimizing directionality relationships. MechANICAL anisotropy of thick section products of heat-treatable aluminum alloys is recognized by producers and users of these products, and the extent of the directional differences is apparent in property tabulations included in handbooks, standards, and specifications.&apos; Attention has also been directed to the existence of important directional differences in the resistance of these products to stress-corrosion cracking. Metallurgical structure factors responsible for these directional differences include, among other possibilities, shape and alignment of grains, voids and nonmetallic inclusions (when present), volume fraction and spatial distribution of secondary phase particles and solid-state precipitates, crystal-lographic textures, and Bauschinger effect. The contributions of the individual factors vary with alloy composition, heat-treated temper, type of working process (forging, rolling, extrusion), and the amount and directional nature of the deformation. In general, the cast ingot used as the starting material for producing these wrought products exhibits only a modest degree of directionality. A monotonic and continuous transition from this nearly isotropic state with progressive hot deformation would appear probable, assuming that the working temperature is sufficiently high to cause continuous dynamic recovery. Several years ago a project was undertaken to evaluate the effects of hot deformation and metallurgical structures on the directionality of thick wrought aluminum alloy products, and the method to be described was developed as an analytical tool in this investigation. DIRECTION NOMENCLATURE The nomenclature system adopted by industry for the three mutually perpendicular directions employed in testing aluminum alloy products includes four terms: "longitudinal", "transverse", "long transverse", and "short transverse". These terms are conventionally related to the external geometry of the product but also by implication to the deformation and resulting metallurgical structure. Occasions arise in which through use of unusual fabricating methods, intentional or otherwise, the structure does not have the usual relationship to external geometry or may be very complex because of inhomogeneity of deformation throughout the piece. The longitudinal direction is generally parallel to the primary rolling direction or to the direction of extrusion. In the case of forging, it is parallel to the direction of maximum extension (not maximum "working" or "flow", as frequently stated). The term transverse is applied to any direction perpendicular to the longitudinal direction in a product having symmetry about the longitudinal axis, and generally, although not always, the deformation to produce these forms is nearly symmetrical in the transverse plane. This term then may be applied to a round, square, hexagon, or other polygonal, symmetrical shape produced by extrusion or rolling or by forging, if produced by a simple, symmetrical drawing procedure. The type of microstructure generally associated

Jan 1, 1970

By R. S. Rickard

Chemical processing of ores has gained new im¬petus in recent years. The reasons are many. They range from the need to process ores that are difficult to beneficiate to the avoidance of pollution. Although many think of chemical processing as a hydrometallurgical operation there are other techniques. An example is chlorination. Chlorination, although examined and discarded by many investigators, is again being considered as a means of extracting uranium1, treatment of silver-lead ores2, and the recovery of base metals from pyrite cinder and ores3. Segregation roasting of copper and nickel ores, a process similar to chlorination, is another chemical treatment being revived.

Jan 1, 1970

By D. W. Tuckwiller

Electroplating is a widely utilized but little understood process. The fact that the average person is in contact with dozens of plated items daily without even being aware that they are electroplated is evidence of the success of the process. Although a complete explanation of electrodeposition involves thermodynamics and modern theories of bonding and catalytic reactions, in its simplest form the process conforms to the following description. A metal salt dissolved in water partially dissociates into negatively charged and positively charged ions. In the case of nickel sulfate dissolved in water, for example, a portion of the salt dissociates into positively charged nickel ions and negatively charged sulfate ions. If an electrical potential is applied between two electrodes in this solution, the nickel ions migrate toward the cathode and the sulfate ions toward the anode. The negatively charged cathode has a high concentration of electrons, which combine with the positively charged metal ions to form neutral metal atoms with a stable electron configuration. These insoluble atoms thus form a deposit on the cathode.

Jan 1, 1970

By E. R. Buchanan, R. E. Reed-Hill

A transmission electron microscope study was made of magnesium single crystals deformed in torsion using the basal pole as the forsional axis. While this type of deformation is predicted to result in the formation of hexagonal networks of screw dislocations, these networks were not observed. The basic dislocation arrangement consisted of arrays of nearly parallel and approximately equally spaced dislocations. The average dislocation density was over an order of magnitude higher than that required to account for the torsional deformation. The observed high rate of work hardening in these crystals is consistent with both their high dislocation densities and the arrangement of dislocations in pile-ups. The experimental observations are also in agreement with the assumption that dislocation sources are activated not only at the surface but at interior locations as well. In considering torsional deformation, Amelinckx and Dekeyser1 postulated that when a torque is applied to a crystal oriented with a glide plane normal to the specimen axis, deformation occurs by the following steps: 1) Nucleation of dislocation sources at or near the specimen surface in areas where the shear stress, resolved along a slip Burgers vector, is a maximum; 2) the screw orientations of the dislocations accommodating the twist move inwards towards the specimen center. If two glide directions lie on the glide plane, the geometry shown in Fig. 1 should result; 3) the screw dislocations that pile up in the central part of the specimen cross-slip to form a grid. At the same time, screws of opposite sign and most edges leave the specimen. Tinder,2 using zinc crystals twisted about the basal pole, independently reached essentially the same conclusions. He suggested a mechanism involving nucleation of ?(1120) screw dislocations at the six points of highest resolved shear stress that lie on the cross-section near the surface. Under the applied shear stress these dislocations were assumed to move inward and interact so as to form a hexagonal network of screw dislocations. Today it is often accepted that rotational slip occurs by a mechanism of the above type, but to our understanding this has never been experimentally proved. This paper reports an experimental study of rotational slip, using magnesium single crystals, that indicates that in this metal rotational slip does not conform well to this mechanism. EXPERIMENTAL PROCEDURES Mechanical Testing. Specimens with a (0002) axis were prepared from magnesium crystals of 99.95 pct purity grown by Jillson&apos;s3 modified Bridgman technique. The crystals were acid machined into cylindri-

Jan 1, 1970

By A. G. Darnley

"The Geological Survey of Canada is devoting consider-able effort to finding ways to make airborne radiometric measurements both quantitative and reproducible. Equipment has been designed by Atomic Energy of Canada Ltd. to provide high count rates in order to minimize statistical uncertainty, this being essential to justify applying terrain clearance and Compton scattering corrections to the data. Correction factors have been determined experimentally and can be applied automatically. Considerable ground work has been undertaken in parallel with equip-ment development in order to determine field parameters.Two airborne gamma-ray spectrometers are described. One is based on three 5-by 5-inch Nal(Tl) detector crystals and is used in a helicopter; the other employs twelve 9-by 9-inch detectors and is used from a Skyvan aircraft. The former is being used to investigate the range of radiometric response from specific rock types, and for the correlation of ground and air measurements; the latter has completed initial trials and will be commencing experimental surveys during 1969.Results are given to show the comparative sensitivities of the various detector sizes, and operational requirements for a gamma-ray spectrometer survey are discussed briefly."

Jan 1, 1970

By John V. Beall

One Sunday night last month the phone rang and it was George Schenck from Penn State. How would we like to see a big scrap operation, he wanted to know. A few days later we were on the Connecticut turnpike headed for New Haven to visit a large scrap operation, M. Schiavone and Sons. George had a large clam basket in the back which he explained was for collecting trophies. The car shredder, he said, turns out some fancy metal shapes. In fact, they have gained a certain acceptance as objets d’art among George&apos;s friends and relatives. He thinks there may be a small, but possibly lucrative secondary market for shredded cars in the art world if the idea is imaginatively promoted. On the way to New Haven we received a briefing on the scrap industry. The scrap business grew from humble beginnings. Mostly it was started by a few immigrant Jews who collected junk in hand- or horse-drawn carts. The fortunate one might even have had a truck. Before proceeding further, we hasten to point out that the word "junk" is strictly taboo among scrap people, who prefer to refer to their industry as the "secondary metals industry."

Jan 1, 1970