Search Documents

By R. Larry Grayson, Douglas F. Scott

Data on health-related illnesses and disease in the mining industry are scarce, and information on rates and costs is not readily available. Substantial amounts of research are being directed to addressing these issues, including work at the National Institute for Occupational Safety and Health’s (NIOSH) mining health and safety laboratories in Spokane and Pitts-burgh. This paper briefly discusses the current status of some miner health-related issues, including those involving coal dust, silica dust, diesel particulate matter, asbestos, noise, lead, welding fumes, and skin disorders, as well as research and other activities aimed at protecting miners from occupational illnesses and disease.

By T. A. Larssen

The efficiency in production of manganese ferroalloys is dependent on the gaseous reduction of the higher manganese oxides in the ores used as raw materials. The materials, descending in the furnace, will meet the furnace gas that contains significant amounts of CO(g) and reduce in subsequent steps, the last step being reduction of Mn3O4 to MnO. This step may to varying extent occur at temperatures exceeding 800 °C, i.e. in the active region of the Boudouard reaction. The gas reduction of Assmang and Comilog manganese ores were investigated in CO-CO2-atmosphere at temperatures up to 1000 °C. It was seen that decreasing ore size correlates to a lower reduction temperature and increasing reduction rate. Similar effect was observed with increasing CO-content in the gas atmosphere. Further, it was found that Comilog ore obtained a complete prereduction at 600 °C, whereas reduction of Assmang ore was not complete at 800 °C for the majority of the experiments.

By I. O. Otunniyi

The natural hydrophobic response flotation method for beneficiation of printed circuit board comminution fines (PCB CF) still requires many studies to further basic understanding of the process and the flotation traits that the PCB CF presents. Varying particle size distribution (PSD) and water recovery under the scheme show that higher mass pull, obtained at the finer PSD, gave lower water recovery but higher value loss. The reverse also holds: the least mass pull at the coarsest PSD used, -106 + 75 µm, gave the highest water recovery per unit mass pull with the highest reverse recovery. This is unlike what obtains in primary resources processing, where higher water recovery is often with increased fines entrainment. The reverse recovery loss here is, therefore, more due to entrapment with the heavy mass pull characteristic of the method than to the entrainment of value with water. Other peculiarities of the system observed are discussed, with the goal of improving the performance of the process, and broadening the general knowledge of flotation systems.

By Launa G. Mallett, Kathleen M. Kowalski, Michael J. Brnich

The characteristics of leaders under the duress of an emergency are important in the development of emergency planning, training, and in the management of an actual emergency. Knowledge of human behavior is an important component in the formation of emergency strategies. The U.S. Bureau of Mines analyzed the leadership behavior in three underground mine fire escapes. The subjects described their escapes during open-ended interviews. Data were coded according to: (1) evidence of leadership behavior, (2) evidence of lack of leadership behavior, and (3) characteristics of the individual in each group who led the subjects out of the mines. This paper discusses the profile of six individual leadership characteristics which emerged from the data.

By J. P. M. Hojem, C. Dimitriou, N. C. Joughin

This paper describes the design and construction of the first experimental underground rockcutting machine from measurements of cutting forces determined in tests on small rock specimens in the workshop. The deficiencies of this design, revealed by stoping with almost identical rockcutting machines, are described. An account is given of the design and construction of further experimental machines incorporating substantial improvements which made them technically feasible for use in production.

By A. T. Iannacchione

Underground limestone mines typically use the room-and-pillar method of mining in the generally flat-lying limestone formations. In some cases the dip may exceed 5° which can result in unique roof instability problems. Stability may be further exacerbated by the presence of horizontal tectonic stresses. Field studies and numerical model analyses are combined to assess the affect of the dip in various stress conditions. The results showed that where the horizontal tectonic stresses are sufficient to cause intact rock failure, increasing dip results in increased failure potential. The effect of the dip is greater when the maximum horizontal stress is parallel to the dip. Two case studies are presented and evaluated against the findings of stress analysis results. The study showed that the empirical rules of orienting headings parallel to the maximum stress are generally applicable to dipping excavations, except when mining in the up-dip direction. The importance of accurately determining the orientation of the maximum horizontal stress is emphasized because the window of favorable orientations relative to the stress is small.

By C. C. Mattax, J. E. Bobek, M. O. Denekas

ABSTRACT investigations in recent years have shown that rock wettability can exert a profound influence on the displacement of oil by water from oil producing reservoirs. Core analyses frequently show oil recoveries from preferentially water-wet rock to be significantly greater than those from preferentially oil-wet rock. Thus, an accurate prediction of water-drive or waterflood oil recovery is dependent on the evaluation of reservoir rock wettability. Laboratory and field studies have been undertaken to examine and develop methods which may be used to measure rock wettahililiy, to investigate factors which may alter the wettability of reservoir rock, and to determine the wettability of specific reservoirs. It has been found that measurement of the rate and volume of spontaneous imbibition of the wet-ting phase by a rock is a reliable and reproducible test for semi-quantitarive determination of preferential rock wettability. Laboratory tests have shown that the wettability of reservoir rock may depend on both the crude oil composition and the rock type. Field and laboratory tests have indicated that coring flulids and core handling techniques can cause significant changes in the wettability of rock surfaces. However, a few fluids, brine in particular, appear not to affect core wettability and may be used when coring to determine reservoir wettability. Core handling and packing procedures have been developed which preserve core wettability during storage and laboratory testing. The wetfability characteristics of six reservoirs have been evaluated by wettabilify tests performed in the field on fresh cores cut with brine or special water-base muds. The tests indicated that all six reservoirs are water wet; however, the de-gree differed from one reservoir to another. INTRODUCTION Although surface properties of reservoir rock and interfacial characteristics of rock, crude oil, and water systems have been discussed for many years, the full significance of these properties to the production of oil is still in the process of evaluation. It is known, however, that one surface characteristic—preferential wettability of the reservoir rock—-is of paramount importance when the reservoir is being produced by water-flood or water-drive mechanisms. The importance of rock wettability has been pointed out by several authors'.',%* who have found that pref- erentially water-wet cores flood more efficiently than oil-wet cores; that is, more oil is recovered from water-wet cores in the early flooding stages than from oil-wet cores. Other authors'," indicate that waterflood oil recovery from cores of intermediate wettability may be greater than that from either strongly water-wet or strongly oil-wet cores. These recent investigations emphasize that the true wettability of a reservoir must be known before the performance of waterflood or water-drive reservoirs can be accurately evaluated. When reservoir wettability is to be determined by core analysis, precautions must be taken to maintain the original wettability which can be altered readily during coring5 nd testing.' In the coring operation the core may be partially or completely penetrated by the drilling fluid which, if it contains surface active materials, may drastically change the wettability of the core. Also, improper core handling during stcrage and testing may change its wettability because of evaporation of fluids or exposure to oxygen or surface active contaminants. One purpose of this paper is to discuss methods for obtaining, preserving, and testing cores without altering their original wettability. In addition, the results of wettability tests on fresh and preserved cores from six reservoirs are presented where special precautions were taken to obtain samples without altering their wettability during the coring operation.

By P. M. Blair, D. W. Peaceman

The shape and position of the gas-oil transition zone during downdip displacement of oil by gas has been calculated using flow equations which include the effects of gravity, relative permeability, capillary pressure and compressibility of the fluids. The calculations treat the problem in two space dimensions, and results are compared with data from a laboratory model tilted at 30° and 60° from the horizontal on displacements near and above the maximum rate at which gravity segregation prevents channeling of the gas along the top of the stratum. The good agreement between calculated and experimental results demonstrates the validity of the tecbnique as well as that of the flow equations. INTRODUCTION Knowledge of the fluid distribution and movement in an oil reservoir is important in producing operations and estimation of reserves. The history of the oil industry has included steady progress in improving the accuracy of calculations which provide the required knowledge. The earliest method of calculating reservoir performance consisted of material-balance equations based on the assumption that all properties were uniform throughout a reservoir.l For many reservoirs such a simple formulation is still the most useful. However, when large pressure and saturation gradients exist in a reservoir, the assumption of uniform values throughout may lead to significant error. To reduce these errors, Buckley and Leverett2 introduced a displacement eqation which considers pressure and saturation gradients. Methods available at that time permitted solutions to the Buckley-Leverett equation in one space dimension; these solutions have been very useful in solving many problems related to the production of oil. However, the one-dimensional methods are not adequate for systems in which saturations vary in directions other than the direction of flow. An example of such a system is the case of gas displacing oil down a dipping stratum in which the gas-oil contact becomes significantly tilted. Of course, the Buckley-Leverett displacement method cannot predict the tilt of the gas-oil contact. Recent improvements3,4 of the one-dimensional Buckley-Leverett method achieve some success in predicting the tilt of the gas-oil contact at sufficiently low flow rates. However, at rates high enough that the viscous pressye gradient nearly equals or exceeds the gravity gradient, even these improved one-dimen,sional methods incorrectly predict the shape and velocity of the contact. Further progress in estimating such fluid movements in a reservoir appears to require consideration of the problem in more than one space dimension. The recent two-dimensional method of Douglas, Peaceman and Rachford5 appears adaptable to calculate changes with time of the saturation distribution in a vertical cross-section of a reservoir. The movement of saturation contours should represent the moving fluid contacts and include the effects of crossflow due to gravity, as well as variations in the rock and fluid properties. The nonlinear nature of the equations used in the method has prevented proof of the validity of the solutions. Douglas, Peaceman and Rachford made some comparisons with experiment but did not include cases in which gravity was important nor cases involving displacement by the nonwetting phase.For these reasons, a test of the two-dimensional method for a case in which these factors are included would be very desirable. The test selected was a comparison of calculated results with those from a carefully controlled laboratory experiment on a model with measured physical properties. The model selected was one in which gas displaced oil down a tilted, rectangular sand pack. The model can be thought of as representing a vertical cross-section taken parallel to the dip of a reservoir. The displacement thus simulates gas displacing oil downdip that might result from gas-cap expansion or gas injection. This report outlines the calculation method used

By Zongliang Zhang

Electrowinning is a significant step in metal extraction processes. Because the nature of electrowinning is to reduce metal from its oxidized state, substantial energy consumption accompanies it. Electrowinning processes of different metals have much in common—the deposition of the metal on the cathode and the counter-reaction on the anode. An advanced model was developed that can be applied to a variety of metal electrowinning processes. A model for specific metals can be readily obtained by modifying parameters such as potential, kinetics, and side reactions in the model. The model incorporates mass transfer, gas-liquid flow, electrochemistry, and deposition, making it a comprehensive electrowinning model. The model is applied to copper, nickel, and zinc and verified with the experimental results. In addition, the parameter settings and results of different metals were compared, showing that this model has great versatility and accuracy, thereby making it an efficient and effective research tool.

By Michael Day, Paul Kos, Scott Brinton

A hydrogeologic characterization and impact analysis was performed for a proposed quarry at the Hitch Rack Ranch located in the Little Turkey Creek watershed southwest of Colorado Springs, Colorado. Continuous multiple channel tubing, nested piezometers, stream flow measurements, and mapping of known seeps were used to define the three-dimensional potentiometric distribution and areas of groundwater recharge and discharge. Water balance considerations, mass balance calculations, and potentiometric response to earth tides and barometric fluctuations confirmed that the granite fracture system in the ridge area of the proposed quarry has an extremely low bulk hydraulic conductivity resulting in minimal groundwater discharge to sustain the baseflow of Little Turkey Creek. The Little Turkey Creek valley forms the major conduit for groundwater flow exiting from the upper part of watershed underlain by granite. This conclusion has significant implications with respect to mine planning to minimize projected impacts to the hydrologic system and preserve this recharge component to downgradient Denver Basin sedimentary deposits.

By H. W. R. Wardlaw

This paper shows how the cost of the drilling operation per 100-ft drilled can be related directly to bit weight, rotary speed and hydraulic horsepower variations. This enables optimum drilling conditions to be determined in a rapid and concise manner. The paper also shows how data for such calculations cun be obtained quickly and accurately by the "drill-off" method suggested by Lubinski. Examples are given to illustrate the principles and methods used. INTRODUCTION The problem of drilling oil wells at lowest cost and hazard needs little introduction, since it has been with us virtually from the earliest days of our industry. With better understanding of the effect of the various factors of bit weight, rotary speed and hydraulic jet action, however, the problem has recently taken on a more scientific aspect, and engineers or groups of engineers have been assigned to study many of the facets of this problem not immediately apparent to the general observer. Moreover, the availability of better equipment and materials has enabled certain practices to be adopted which were hitherto impractical or uneconomic. This has paved the way for further efforts to reduce footage costs, and so on. The improvements to be made in drilling technology and cost reduction are by no means exhausted, and we still frequently hear of new records being set and new materials and equipment becoming available. Some of the analytical methods used by the author to assist in promoting faster and more economic methods of drilling, particularly in Venezuela, form the basis for this descriptive study. STATEMENT OF THEORY AND DEFINITIONS In a highly competitive industry, it is no longer permissible to regard penetration rate as the sole criterion for drilling efficiency. Every new technique, however spectacular, must nowadays be viewed in the cold light of whether it will eventually lead to lower cost per foot drilled. In the exposition which follows, therefore, actual drilling rates will play only a secondary role, and attention will be focused on the more important aspect of cost per foot drilled. Changes in drilling factors such as weight and rotary speed will be studied in the light of how they directly affect the cost of operations. The advantage of this method is twofold—(1) cost increments are indicated directly; and (2) the relationships are, surprisingly enough, simpler than those relating to drilling rates. To achieve these advantages, it is necessary to introduce a new unit of measurement which, although unfamiliar, is readily understood. The unit in question will be referred to as the "actual drilling cost factor" and will be designated by the symbol h. The unit is defined as the number of rotating hours taken to penetrate 100 ft of formation. The unit can be obtained immediately from the actual drilling rate (r) in feet per hour; thus, This latter transformation is so easily effected that it may be convenient to use h as an international symbol for drilling cost, and to delay conversion to dollars, bolivars, pounds, etc, per foot until actually required (e.g., for fiscal reasons, etc.). In actual operations, h was found to vary in a relatively simple manner with increases in bit weight. The variation in h with rotary speed was found to be somewhat more complex. However, this also could be enormously simplified by introducing a further factor known as L or relative bit life. The factor L is also defined very simply by dividing 1,000 by the rotary speed (N) in revolutions per minute.

By Niels Verbaan

NioCorp is developing the niobium/scandium/titanium Elk Creek carbonatite deposit. The probable reserve announced by the company in 2017 indicated significant niobium (0.79% Nb2O5), titanium (2.81% TiO2), and scandium (71 g/t), and is composed predominantly of calcite, dolomite, and ankerite. Niobium is mostly (80%) contained in pyrochlore with the balance in various Fe-Nb-Ti oxides, which also host most of the titanium. Scandium is primarily deported in dolomite, with lesser quantities in pyrochlore and biotite. The process flowsheet recovers separate niobium, titanium, and scandium products. Scandium is extracted from whole ore hydrochloric acid leach solutions using solvent extraction and is further refined through a re-leach and precipitation process. Scandium leach residues are treated in a sulphuric acid sulphation process to recover separate niobium and titanium precipitates as well as to solubilize the remaining scandium. Both hydrochloric acid and sulphuric acid reagents are recycled within the flowsheet. This paper will discuss key bench and pilot test results of the niobium extraction and recovery circuits and will present a conceptual flowsheet developed by the project team for NioCorp at SGS Minerals.

By M. Kaitz

A continuing discussion in both the petroleum engineering and economic literature is directed to the difficulties encountered in the use of discounted cash flow rate of return (DCF) as a measure of investment worth. Although useful in most Instances, DCF has been criticized because it is time-consuming in its trial-and-error solution, theoretically invalid, not adaptable to cash flow streams yielding multiple return solutions and not entirely reliable in selecting between mutually exclusive investments. The theoretical invalidity of DCF stems from the reinvestment assumption implicit in the calculation that earnings are reinvested at the DCF rate. The emerging consensus of the economic literature is that the net present value or the present worth of the net cash flow stream (discounting at the average opportunity or cost of capital rate) is more correct and reliable. Other criteria proposed have been ratios of net present value divided by initial investment or by present value of all investments in a project. All of these criteria are simple to determine and explicitly assume a reinvestment rate for [he income generated by a project. This paper develops and discusses a theoretically valid profitability criterion which is simple to compute and retains the appeal of a percent return on investment. It is called "percentage gain on investment" or PGI. It measures the gain an investment is expected to realize over like capital invested in the average opportunity and explicitly considers reinvestment potential. Why add another Concept to the large array of investment criteria now available, any one of which, or perhaps a combination of several, appears to embrace the form's (or individuals) objectives? The answer is that not one of the existing criteria provides both a readily comprehensible and theoretically valid measure of risk coverage that has general application. The proposed PGI does fulfill these requirements. INTRODUCTION An ancient expression warns that "one must yield to the times" — there are better ways of doing things. A review of the petroleum engineering and economic literature on one topic alone, measurement of investment worth, certainly is witness to this truth. In use for a number of years, the DCF has recently received attention, directed mainly to its theoretical invalidity. Several alternatives to DCF have been proposed to provide a valid, simply determined criterion to describe investment worth and to overcome the criticisms previously mentioned. This paper introduces another method called percentage gain on investment (PGI) and is proposed as but one of several yardsticks that should be used in making investment decisions. MEASURES OF INVESTMENT WORTH This paper will consider only those criteria which give weight to the time pattern of future earnings. These criteria are usually compared with an average opportunity rate or cost of capital of the firm to judge the relative worth of the investment. For purposes of demonstration, a 9 percent average opportunity rate will be used throughout this paper. Implicit in the DCF calculation is the assumption that earnings are reinvested at the DCF rate. Some argue, though, that there is no reinvestment assumption,' that the DCF rate is simply that maximum rate of interest one can pay on the investment over the life of the project and break even. The determination of DCF is accomplished by discounting the net cash flow stream at that rate (DCF) which will yield zero. The question is: why should reinvestment potential be explicitly considered in calculating return on investment or other criteria measuring economic worth? Perhaps the answer lies in consistent or equal treatment of future cash flow. It appears entirely illogical to give different present worth value to $1 received, say, 10 years from now, which is the circumstance resulting in comparing projects with different DCF returns. In fact, $1 received in 10 years has the same value regardless of which project generated the income. DCF return thus favors investment projects which are expected to provide early income as compared to those providing long-term income. Not surprisingly, the controversy on reinvestment assumption is an old one. Hoskold' discussed this same problem in 1877. He considered the future income from mineral properties as an annuity or a series of fixed future payments. (As will be demonstrated, his equation can be modified for variable income.) Prior to Hoskold, the value or what one could pay for the mine, was determined with the use of standard, single-interest tables. Here is what Hoskold said with regard to these tables. "This table, and others of its kind, to be found in most works on annuities, is constructed correctly according to

By Sunil Vytla, Akash Adhikari, Purushotham Tukkaraja

Blasting operations produces gases and fumes that may be toxic or non-toxic in nature. A detonation of commercial explosives such as ANFO, emulsion, and dynamite would ideally produce only nontoxic products such as steam (H2O), carbon dioxide (CO2) and nitrogen (N2). However, in the real world, the detonation of explosives produces toxic products such as nitrogen dioxide (NO2), nitric oxide (NO) and carbon monoxide (CO). The focus of this study is the blast fumes entrapped in the muckpile. Fume clearance and workplace re-entry time studies performed in the past have overlooked the toxic gases entrapped in the muckpile. Studies show that as much as 60% to 70% of the fumes or gases produced during blasting underground can remain entrapped in the adjacent rock mass or in the muckpile. The toxic fumes trapped inside the muckpile are slowly released and could be fully uncovered during the mucking process. Exposure to these gases or fumes is hazardous to mine workers. In this study, author have analyzed the nature of fume flow, i.e. accurately predicting where and how the fumes flow after an underground development/tunnel blast. This will help in determining i) precise re-entry times for the workers ii) rate and direction of the fume flow. Computational Fluid Dynamics (CFD), a mathematical simulation technique that predicts fluid dynamics phenomena is used for this purpose. CFD is preferred over physical models because it is inexpensive, once the accuracy is established, a wide range of scenarios can be simulated quickly, and the toxic gas flow patterns through underground openings can be analyzed efficiently. For this study, CFD is performed using SC/Tetra software owned by MSC software company.

By Gerardo Fuentes

The stoichiometry and kinetics of the hydrothermal reaction of enargite in copper sulphate solutions was investigated in the range 140–300 °C, and particle size under 15 and 50 μm. The stoichiometric experiment was performed at 300 °C, using one gram of sample (96% enargite, 4% tennantite) and 100 mL of copper sulphate solution (10 gpl) at 1.2 pH. Enargite reacted completely after 80 min. A solid product was obtained and characterized by XRD. The main product was chalcocite (M) and some traces of djurleite and chalcocite (Q). Tennantite did not react under these conditions. The kinetic experiments were conducted at 140 °C, 190 °C, 250 °C and 300 °C. From fitted data and Arrhenius equation the calculated activation energy (Ea) was 51 kJ/mol. According to the hydrothermal transformations studied, the reactivity of different phases found in the copper concentrates was bornite > chalcopyrite > covellite > sphalerite > pyrite > enargite > tennantite.

The January General Meeting of the Institute was held in Kelvin House, Johannesburg, on 15th January, 1969 at 4.30 p.m. Mr R. C. J. Goode (President) was in the Chair. There were also present eighteen Members, including Messrs F. P. Bath, H. Britten, J. K. E. Douglas, P. Lambooy, V. C. Robinson, W. T. Stobart and P. W. J. van Rensburg (Council Members), Messrs J. C. Hall, P. C. Pirow, Dr D. I. Legge, Messrs E. R. Rudolph, H. R. Reid, Dr N. Stutterheim, Messrs B. F. van der Merwe, L. W. P. van den Bosch, D. T. Watt, M. Youngworth and T. Zadkin. Two Associate Members, Dr P. R. Jochens and Mr D. A. Viljoen. Two Students, Messrs R. P. W. Henrard and D. Ossin. Sixteen Visitors, including Messrs I. Barnes, B. F. Bath, S. Botha, P. A. du Plessis, K. Edwards, Dr F. S. Fulton, Messrs H. Grant, B. Havenga, L. Kok, Dr D. Lasar, R. Sandler, C. W. Wolhuter and J. D. Young. Secretary, Mr D. C. Visser. Total present: Forty. MINUTES The President: "May we confirm the minutes of the meeting held on the 20th November, 1968, as published in the December, 1968, issue of the Journal?" Agreed. MEMBERSHIP The President: "I have much pleasure in announcing that the names of the under-mentioned candidates, having been published in accordance with By-Law 5.2.2, Council has elected them to membership of the Institute in the following grades: Members: Basil James Jackson and James Petrie Archibald. Associate Members: Ronald Creasy, Hugh Angus McCallum and John Barton Cunliff. Graduate: Hermanus Isak Johannes van der Merwe. Affiliate: Edgar Ramsay. Student: Petrus Daniel Wolmarans. MEMBERS TRANSFERRED TO A HIGHER GRADE From Affiliate to Associate Member: Neil Bradfield and Mervyn Bayard Allman. "I welcome the newly elected members to the Institute and congratulate those members who have been transferred to a higher grade." (Applause). GENERAL BUSINESS The President: "Are there any matters to raise under this heading? If not, we will proceed to the next item on the agenda which is the presentation of today's paper."

By P. B. Crawford, W. L. Huskey

A study has been made to determine the effects of random vertical fractures existing in a reservoir matrix on the effective matrix properties and producing characteristics of a well. The study indicated that short vertical fractures may distort the isopotentials by 1 percent in the vicinity of the fracture. A correlation was developed which showed the effect of fracture density on the producing capacity of a well. The correlation indicated that fracture shape had little effect on producing capacity, but that total fracture length was closely correlated with the producing capacity. Effective values of reservoir permeability were found to correlate closely with fracture density when measured parallel to the direction of flow. INTRODUCTION In reviewing the petroleum literature, it is found that in most analytical solutions of hydrocarbon reservoir behavior the assumption is made that the rock is uniform throughout although core analysis and well logging surveys indicate that substantially all reservoirs are heterogeneous and some are fractured. Only in recent years have investigators studied the effects of reservoir hetrogeneity. Russell1 discussed the effect of fractures in reservoirs. The literature indicates that fractures greatly affect the exploitation of man reservoirs. This is described by Elkins and Skov2 and Little-field et al. 3 Several types of reservoir heterogeneity have been studied by unsteady-state methods. In 1959, Landrum et al. 4 showed that transient phenomena in hydrocarbon reservoirs could be studied by thermal models. pickering5 studied the flow of heat in stratified linear reservoirs consisting of plates of different metals separated by sheets of rubber which were suddenly exposed to a low-temperature source at one end. Cotman6 studied both laterally and vertically heterogeneous thermal model reservoirs with special reference to cross flow. Another type of reservoir heterogeneity involves the presence of highly permeable, circular lenses around or near the wellbore which was studied by Miesch7 using a thermal and a steady-state model. Many studies have been made of the effects of induced hydraulic fractures on well performance. 8-10 Work regarding vertical fractures that exist initially in the reservoir was reported by Givens, et al.11 Since there appears to be little published work on the importance and influence on reservoir performance of fractures that exist out in the rock matrix, this study was conducted to determine the effects of vertical fractures on pressure distribution, producing capacity and the effective permeability of the reservoir rock. The analogy between the flow of electrical current through a conducting body and the flow of fluid in a porous medium provides a convenient method of studying various aspects of petroleum reservoirs. For electrical radial steady-state flow,12 For steady-state fluid flow, With the above analogy, it is only necessary to establish the ratio of the values of the electrical units in terms of the corresponding flow units to make the analogy quantitative. The ratios are shown below.

By John N. Murphy

In fiscal 1996, the US Congress directed that the US Bureau of Mines (USBM) be closed. Certain functions were reassigned to other agencies. The remaining employees were separated and the unoccupied sites were decommissioned. As a result, 12 locations were closed and about 1,200 employees were terminated in March 1996. About 600 employees at five locations were reassigned to other federal agencies. This article provides a summary of the continuing functions, the agencies involved and the points of contact for each continuing function. The functions that were discontinued are also identified.

By T. Sterry Hunt

But little was known of the coals of Southeastern Ohio until the present survey of the State under Dr. Newberry began its work. The results of the geological investigations of Prof. E. B. Andrews in this region, and of the chemical investigations of Prof. T. G. Wormley, both of which appear in the reports of the survey for 1869 and 1874, and more recent special reports by the former, together with some data for which I am indebted to the kindness of Dr. Newberry, and my own limited observations, have served me for the preparation of the following notice of the coals lying on the western border of the great Appalachian coal-basin in the region drained by the Hocking River and its tributaries, and belonging to the Lower Coal-Measures. Some uncertainty exists as to the place in the suc- ' cession of the lower coals to be assigned to the seams known and mined in the Hocking Valley. It is the opinion of Prof. Andrews that the inequalities of the original surface were such that we cannot identify in that region the lowest coals known in Northwestern Pennsylvania and the contiguous parts of Ohio, but that we must rather count from above downwards. These conclusions Dr. Newberry is not prepared to accept, and further researches will be necessary before certainty can be attained in this matter. Meanwhile it seems, from a study of its relations to the Pomeroy or Pittsburgh seam, that what is known as the great vein of the Hocking Valley, occupies the horizon of the Upper Freeport coal, E of the Pennsylvania survey, or No. 6 in Dr. Newberry's enumeration, counting from the base. This seam, in the region in question. assumes certain characteristics which, taken in connection with its geographical position, give it a great importance among the coals of the State. The area to be noticed includes the whole or parts of several townships in Perry, Hocking, Vinton, and Athens Counties, lying near the margin of the basin over which the vein in question assumes the character of a dry-burning or splint coal, and has a thickness varying from six to ten and even twelve feet. Its precise limit southward cannot at present be clearly defined, but it has been found as far south as the line of the Marietta and Cincinnati Railroad, with a thickness of six feet, and is mined at various points along the valley of the Hocking River, near Nelsonville, where it attains six or seven feet. To the northward, along the tributaries of this river, Sunday and Monday