Search Documents

By J. Campbell

Long freezing range casting alloys are particularly susceptible to a type of porosity which is observed to form in layers parallel to the supposed position of the isotherms in the solidifying casting. Under favorable conditions (which appear to be typified by low-temperature gradients in the casting giving rise to a wide and more or less uniform pasty zone, and which arise from several factors, particularly: a) wide freezing range alloy, b) high thermal conductivity of metal, c) low thermal conductivity of mold, and d) high mold temperature3) layer porosity has been observed in many different casting alloys: copper,' aluminum, magnesium,' steels, and high-temperature alloys.3 Baker4,5 and later cibula6 argue that layer porosity occurs because of thermal contraction, in a manner analogous to hot tearing. In outline, the theory consists of the establishment of a coherent dendrite network by the impinging of dendrite tips. Subsequent shrinkage imposes tensile stresses on the network which tears perpendicularly to the stress, i.e., parallel to the isotherms. If these tears are not filled by the inflow of residual liquid then layers of porosity result. Baker7 attempted to test whether the porosity was the result of thermal contraction by casting test pieces in a mold designed to accentuate hot tearing. However, no significant increase in porosity was observed. This negative result of Baker's critical experiment appears to be substantiated by numerous observations, particularly the experiments by Lagowski and Meier8 on Mg-Zn alloys covering the range of zinc contents up to 30 pct Zn. These clearly reveal that the maxima for the incidence of hot tearing and layer porosity are well-separated, occurring at 1 and 6 pct Zn, respectively. Furthermore, the thermal contraction maximum occurred at 1 pct Zn, indicating that hot tearing is associated with contraction in the solid state, and not with porosity. These observations are further substantiated by the elementary consideration that the thermal contraction of the casting is likely to produce (if anything, since the temperature difference across casting of high thermal conductivity, such as aluminum and copper, is likely to be negligible) a compressive stress on the

Jan 1, 1969

By J. E. Lawver, J. L. Wright, H. R. Kokat

Mesabi semitaconite and oxidized taconite ores that cannot be concentrated by froth flotation can be rendered amenable to flotation through partial concentration in a high-in tensity wet magnetic separator. Since 1964, a method for accomplishing this precon-centration has been under development at the Minnesota Mines Experiment Station, where several hundred tons of ore have been successfully processed. This paper is an analysis of the performance of the separators used at the Station. At present the United States is producing about 85 million tons of iron ore a year, and nearly 55 million tons of this comes from Minnesota. Nearly half of Minnesota's production is in the form of magnetite taconite pellets —the remainder being wash ore and gravity concentrates. As the demands of the blast furnace operators become more stringent - and they are becoming more so yearly — these demands are met by improved iron ore beneficiation technology. Furthermore, there is no doubt that as magnetite taconite, gravity ores, and wash ores are exhausted, new processes will be developed to produce a product comparable to magnetite taconite pellets from Minnesota's vast reserves of oxidized taconite and semitaconite. The magnetite taconite ores are rather easily bene-ficiated by conventional, low-intensity (500- to 1400-gauss) magnetic separators, followed, in some plants, by froth flotation of the magnetic concentrates.

Jan 1, 1969

By M. H. Waxman, L. J. M. Smits

A simple physical model was used to develop an equation that relates the electrical conductivity of a water-saturatedshaly sand to the water conductivity and the cation-exchange capacity per unit pore volume of the rock. This equation fits both the experimental data of Hill and Milburn and data obtained recently on selected shaly sands with a wide range of cation-exchange capacities. This model was extended to cases where both oil and water are present in the shaly sand. This results in an additional expression, relating the resistivity ratio to water saturation, water conductivity and cation-exchange capacity per unit pore volume. The effect of shale content on the resistivity index - water saturation function is demonstrated by several numerical examples. INTRODUCTION A principal aim of well logging is to provide quantitative information concerning porosity and oil saturation of the permeable formations penetrated by the borehole. For clean sands, the relationships between measured physical quantities and porosity or saturation are well known. However, the presence of clay minerals greatly complicates log interpretation, particularly the electrical resistivity and SP logs, and considerably affects evaluation of hydrocarbon-bearing formations. The conductance and electrochemical behavior of shaly sands and their relation to log interpretation have been studied by many workers. wylliel and Lunch2 reviewed this work in some detail. Virtually all laboratory measurements of electrical resistivity and electrochemical potential of shaly sands published to date are the work of Hill and Milburn.3 Their measurements were made on about 300 cores covering a large variety of sedimentary rocks, and a wide range of equilibrating NaCl solution concentrations. Hill and Milburn described their conductivity data by an empirical equation in which the shaly sand conductivity Co was expressed as a function of the solution conductivity C and two parameters b and F01 . The quantity b was shown to be a measure of the effective clay content of the rock, being approximately proportional to the cation-exchange capacity of the rock divided by its pore volume. The latter ratio is designated as 9, in this paper and has the dimensions meq/ml or equiv/liter. Qv is identical with the term representing the concentration of fixed charges in the Meyer-Sieved and Teorel15 theory of permselective membrane behavior. F01 is a formation resistivity factor referred to a hypothetical equilibrating solution resistivity of 0.01 ohm m at 25C,* where clay effects presumably are minimized. F01 was correlated to porosity by an Archie-type equation.6 The Hill-Milburn equation describes their data with a standard deviation of approximately 1 percent and a maximum deviation of + 10 percent. Shaly sands behave as permselective cation-exchange membranes, their electrochemical efficiencies increasing with increasing clay content. The electrochemical potential data of Hill and Milburn were expressed graphically, and demonstrate that the membrane efficiency (or cation transport number) of these sands is a function only of the b value (i.e., Qv) and the respective salt concentrations of the two solutions forming the liquid junction in the sand. The diffusion potentials are not dependent on F01 or any parameter relating to the porosity or pore geometry of the rock. The Hill-Milburn resistivity equation correctly predicts a decreasing sand conductivity Co with decreasing solution conductivity C?. However, at some low value of C,, the calculated Co-C, function goes through a minimum; with further decrease in C?, the predicted sand conductivity increases sharply. As pointed out by Hill and Milburn, an increasing value of Co with decreasing C, is physically meaningless. Since this occurs below the range of practical values of C,, the usefulness of the empirical equation is not affected when

Jan 1, 1969

By Jon C. Jenkins

In order to plan the most efficient mine installation, a company should take advantage of all available information and tools. One of the first factors of a coal reserve that needs to be determined as accurately as possible is the quality of coal the mine will have access to during the life of the installation. With the aid of many types of well logs and computor analysis, we are investigating several methods of log correlation to determine such data as moisture, ash, sulphur, and BTU on an in place basis. It may be possible to determine this data more accurately in this manner than by using diamond drill cores for analysis and thus allow for a more profitable mine installation. The production of an underground mine is based on many factors, two of these being roof control and line water, where present either in the roof or coal seam. Using many of the same logs obtained from reserve and active mine areas, we have attempted to determine roof and floor characteristics such as strength, lithology, and moisture properties. Using data obtained from this program, we will make comments on possible length of bolt to be used, possible mining width, and pillar size as they would pertain to these reserves and active mine areas.

Jan 1, 1969

By K. K. Clark

Excessive injection pressures in water injection wells may create deeply penetrating fractures, or may open up existing reservoir fractures. If these fractures are oriented toward offset producing wells, oil recovery at injected water breakthrough and ultimate recovery will be impaired. A method of calculating fracture lengths from pressure fall-off test data is presented. The method is based on a linear flow model that simulates conditions present during the early-time period after shutting in an injection well. Fracture lengths can be calculated directly if formation permeability is known. A graphical technique is presented that provides fracture lengths based on permeabilities calculated from normal fall-off tests, where those permeabilities are adjusted for flow geometry. Test data from four injection wells and results obtained from applying the method to these wells are discussed. Introduction Rates of water injection into nonstimulated wells in low permeability reservoirs frequently fall below economically desirable levels. Therefore, some form of stimulation such as hydraulic fracturing often is performed on these wells. Usually these fractures penetrate a short distance from the well — short as compared with interwell spacing — and therefore should not create problems of water channeling to offset producing wells. In the past, some operators have been tempted to increase injection pressures continually to maintain a specified injection rate. But pressures cannot be increased indefinitely. Field data indicate that continued injection above fracture opening pressure can cause excessively long fractures to approach between well distances. If these long fractures intersect or closely approach offset producing wells, premature water breakthrough can result. It is difficult to seal effectively these fractures by various workover procedures after premature water breakthrough has occurred. This paper describes testing procedures that are potentially capable of detecting premature water breakthrough before it occurs. Knowledge of fracture lengths and fracture opening pressures can assist field engineers in selecting optimum operating conditions for water injection wells. Fracture lengths should be calculated from pressure fall-off tests on injection wells, and maximum permissible iniection pressures should be determined from step-rate injectivity tests. Equipped with this information, the field engineer is in a better position to recommend for a particular injection well the optimum operating conditions that will lessen the chances of channeling to offset producers. Historically, pressure transient tests have been conducted primarily on producing wells and analysis procedures have been based on radial flow concepts. Several authors have suggested that these same procedures be applied to tests conducted on water injection wells. This application is justified for wells that are not connected to extensive fracture systems. However, if the formation is severely fractured, the interpretation methods must be modified. Several authors have presented the pressure response of various systems that are intended to simulate reservoir conditions. A paper by Russell and Truitt* on vertically fractured svstems is probablv the most useful from the standpoint bf the fieid engineer. Russell and Truitt presented the pressure-vs-time behavior of a well connected to vertical fractures with various fixed lengths. Their permeability adjustment technique is used in this paper to refine methods of calculating fracture length and interwell permeability. Theory and Definitions Three flow-system geometries are considered in analyzing injection well test data. These various geometries are applicable during specific time intervals of transient pressure tests. Schematic drawings of the flow models, and the time intervals over which they are applicable, are shown in Fig. 1 in the chronological order that they are applied to the pressure response of water injection wells in fractured formations. The very early response is simulated by an infinite linear system as shown in Fig. 1A. This representation permits the calculation of matrix surface area exposed to the fracture. The model shown in Fig. 1B is identical with the one studied by Russell and Truitt. They evaluated the transient pressure response of this vertically fractured system by finite difference techniques. The results were presented as tabulations of dimensionless pressure drop functions for a range of fracture lengths. A semilog plot of these data shows that the apparent matrix permeability can be related to the true matrix permeability by a simple exponential function. Their adjustment factor is used in this paper to improve the accuracy of matrix-permeability and fracture-length calculations.

Jan 1, 1969

By J. C. White

This paper, after a brief introduction giving the history and geology of the area, deals with mining operations at the Copper Mountain mine of Gaspe Copper Mines, Limited. It discusses development operations, and then goes into the mining methods employed, covering drilling, grade control, blasting practice, loading and hauling, and the road and service machines used.

Jan 1, 1969

By J. J. Frawley, W. J. Childs

The dynamic nucleation of supercooled bismuth and Bi-Sn alloys has been studied over a frequency range of 15 to 20,000 cps. For low-frequency vibration, a minimum vibrational energy was required for enhancement of nucleation. Above this critical energy, the dynamic supercooling was less than static supercooling showing that vibration promoted nucleation. The amount of dynamic supercooling continued to decrease with increasing vibrational energy until a minimum or threshold value was reached. This minimum value of supercooling for nucleation remained constant joy all further increases in vibrational energy. For higher frequencies, similar results were observed. This behavior has been related to the necessity of cavitation for dynamic nucleation. When a liquid is cooled to a temperature below its equilibrium melting point, the solid phase is more thermodynamically stable. However, for solidification to occur, a two-step process, nucleation and subsequent growth of the solid phase, must occur. When a liquid is supercooled, that is cooled below the equilibrium melting point, the controlling process for solidification to begin is the rate of nucleation. Once nucleation has occurred, the solidification process is controlled by the rate of growth. Nucleation can be induced by two factors: either by a catalyst or by the use of mechanical shock. Numerous investigators1-4 have studied the effect of nucleation catalysis but much less systematic study has been made of nucleation by mechanical shock waves. The influence of vibrations on grain size in castings and ingots has been studied by many authors but no clear understanding of the mechanism or accurate prediction of the effect has been presented.5 It would be intuitively expected that the further the departure from equilibrium (i.e., the greater the supercooling), the easier it would be to induce nucleation. This has been quantitatively demonstrated both by walker6 and later by Stuhr,7 that the greater the degree of supercooling the easier it is to nucleate by a shock wave. Stuhr also attempted to obtain the mechanical energy required for nucleation of bismuth as a function of supercooling. He vibrated a crucible containing supercooled metal at low frequencies and various amplitudes and noted the corresponding dynamic supercooling obtained. The amount of supercooling was inversely proportional to the mechanical energy applied. Limitation of his experiment was the problem of the confinement of the liquid in the crucible without splashing and minimizing other unwanted modes of vibration. Tiller et al.8,9 did similar work on tin and Sn-Pb alloys using an electromagnetic stirring device. Their conclusions were that the magnitude of the magnetic field strength did not affect the amount of undercooling at which nucleation was initiated. While conclusive experimental results have been lacking to explain this effect of mechanical vibration on inducing nucleation, a number of theories have been proposed. Two of these theories are discussed below. 1) The Change in Melting:- Point Locally Due to the Change in Pressure (Clapeyron Equation). According to Vonnegut10 the most plausible explanation for the nucleation of a supercooled melt by cavitation is the effect of changing the melting point by a change in pressure. For materials where the volume decreases on solidification, an increase in pressure raises the melting point; for materials which expand on solidification, the melting point is raised for a decrease in pressure, i.e., rarefaction. Using the Clapeyron equation, the melting point of a metal can be calculated as a function of pressure. If it is assumed that the equation can also be used to calculate the temperature of nucleation of a supercooled melt as a function of pressure (i.e., the temperature of heterogeneous nucleation will increase with pressure at the same rate as the melting point), the amount of supercooling required for nucleation will be constant at all pressures as shown in Fig. 1. It is obvious that an isothermal change which results in an increase in melting point results in an equal increase in supercooling. This increase in supercooling may now be sufficient for nucleation. A pressure of 80,000 atm was calculated, using the Clapeyron equation, as the pressure required to increase the temperature of nucleation of nickel by 200°C. According to Lord Rayleigh,11 this very large pressure could be generated for a very brief period of time by the collapse of a cavity. This pressure wave is radiated in all directions from the collapsed cavity. If the temperature of the melt is slightly below its equilibrium melting temperature at atmospheric pressure, stable growth can follow; that is, once nucleation occurs, growth becomes the main driving force of the solidification process. This proposal has been extended to water which expands on freezing by assuming that nucleation occurs during rarefaction following the pressure pulse. This negative pressure pulse should follow immediately after the positive pressure pulse with its magnitude approaching the critical tensile strength of the liquid. The negative pressure developed during this period would raise the melting point of water and thus promote nucleation. Hunt and jackson12 have suggested this for water. Similarly, it could be postulated that bismuth which also expands on freezing could be nucleated during the negative pressure pulse. 2) Nucleation by a High-pressure Phase. An extension of the Clapeyron equation to systems where density decreased on freezing at atmosphere pressure has been proposed by Hickling.13 The phase diagram for water initially shows the well-known decrease in

Jan 1, 1969

By T. E. Scott, D. H. Sherman, C. V. Owen

Mechanical properties and optical metallographic characteristics of vanadium containing 53 ppm (wt) H were investigated from, 77° to 298°K. A sharp ductile to brittle transition induced by the presence of hydrogen was observed between 238° and 223°K and a mar-tensitically formed hydride appeared at 200°K. While there appears to be a subtle relationship between the hydride formation and the ductile-brittle transition, it was concluded that the hydride per se was not sufficietzt to cause the severe em brittletnent. On the basis of the metallographic experiments and the results of a Petch analysis it is suggested that the mechanism of the embrittlement involves a reduction of the true surface energy, or cohesion, of the uanadiunz. THAT hydrogen can severely embrittle vanadium is well-documented;'-5 however, the mechanism by which hydrogen induces the observed embrittlement has not been established. It is not known whether the embrittlement of vanadium is caused by the formation of vanadium hydride or by a more subtle role of hydrogen. Until very recently6>' the solid solubility of hydrogen in vanadium at temperatures in the,range of the embrittlement was not known to a useful accuracy. In general, a severe embrittlement of the type produced by the presence of hydrogen in vanadium can be caused by changes in either of two properties of a metal. Either the yield stress of the metal is raised to the extent that plastic deformation at the tip of a crack cannot occur or the cohesive properties of the metal are reduced, at least locally, to the point at which cleavage is the natural response to applied loads. Of course a combination of these is possible. It is not known which of these properties of vanadium is influenced most by the addition of hydrogen. The purpose of this investigation was to determine the role of hydrogen in the embrittlement of vanadium. Accordingly, the solubility of hydrogen in vanadium in the temperature range where embrittlement is most severe was determined, the appearance of vanadium hydride was examined in relation to the initial ductile to brittle transition temperature, and an attempt was made to evaluate the effect of hydrogen on the yield stress and cohesive properties of vanadium. MATERIAL AND PROCEDURES Sample Preparation. The vanadium used in this investigation was prepared by the iodide refining process described by Carlson and owen.' Three ingots, 3 in. diam by 6 in. long, were cold-swaged to 0.096 in. diam, cut into short lengths, and then arc-melted under purified argon into one ingot. This process was repeated to insure a uniform composition in the final ingot. Chemical analysis of the metal is given in Table I. On the basis of work of Loria et a/ .' the following sequence of treatments was performed in order to obtain a uniform equiaxed ultimate grain structure: a) cold swage q-in.-diam ingot to 0.230 in. diam; b) anneal 6 hr at 1000°C in vacuum; c) by cold swaging reduce 81 pct in area in three steps: 0.230 to 0.187 in. diam, 0.187 to 0.150 in. diam, 0.150 to 0.096 in. diam. This sequence provided the desired grain structure after subsequent annealing treatments. Because annealing in evacuated quartz capsules resulted in contamination by oxygen, all anneals in this investigation were performed in a 304 stainless-steel chamber under a dynamic vacuum of 10- I Torr with the vanadium wrapped in tantalum foil. Prior to all annealing treatments the wires were electropolished for 1 min at 16°C in an 80 pct methanol-20 pct sul-furic acid electrolyte at 12.5 v. Following the final reduction the 0.096-in.-diam wire was cut into 2-in. lengths. A 1-in. gage section was reduced to 0.090 in. diam by electropolishing as above. Five different grain sizes were obtained by annealing the 2-in. samples at different temperatures for 8 hr to insure uniform grain size and residual hydrogen removal. The annealing temperatures used and the resulting grain sizes are given in Table 11. The final step in sample preparation was to charge half of the specimens of each grain size with hydro-

Jan 1, 1969

By G. Knight

"Results of a program of dust research carried out at the Mines Branch Laboratory, Elliot Lake, indicate that dust-concentration estimates vary greatly, depending on the sampling instrument, the assessment technique and the properties of the dust cloud. The wide range of the ratio between the estimates by any pair of instruments shows that the correlation between the health hazard and dust-concentration estimates by most existing sampling instruments must be questionable. Important studies are being carried out to permit the definition of mine environments in more precise technical terms. The influence of size selection, the physical property measured, composition and sampling period on the assessment of the health hazard are discussed."

Jan 1, 1969

By D. M. Steelman

Digital systems have been employed in industry as an aid in process evaluation and control for about 20 years. The earlier systems were quite simple and did little more than periodically scan a multitude of process variables, perhaps comparing them to alarm limits, and print out the results. As time passed, the needs of industry and the imagination of process engineers became more demanding. Rather than perform only alarm checking and logging, operating guides were generated to help the operator gain optimum performance from the process. Eventually, systems were entrusted with the job of manipulating the set points of the local analog control loops in a (DDAC) digitally directed analog control mode. Today digital systems are used to gather all-the process information, including both analog and digital variables; to make the necessary data manipulations; and to control the process end elements in a (DDC) direct digital control mode. During these years of transition from the very simplest systems to the complex systems of today, the demands upon the system engineer have been every increasing. The process engineer has required, among other things, more computational ability at high speeds, faster input and output rates, greater flexibility, better communication facilities (man-machine interface), (process oriented software), and finally, greater reliability at lower cost.

Jan 1, 1969

By William E. Bruce

The Bureau of Mines performed drill calibration tests on two industrial percussive drills of 2-5/8- and 3-1/2-inch piston diameters to determine operating characteristics for their use in conjunction with penetration rate data in developing drillability equations and furthering the knowledge of percussive drills. The use of a linear velocity transducer for measuring piston velocities and application of its instrumentation are described. Data presented include relationships between maximum piston velocity and feed air pressure other results confirm the theory or data of previous investigators, and some comparisons are made with the performance prediction formulas of other investigators.

Jan 1, 1969

By R. L. Klueh, W. W. Mullins

During the course of a study on the periodic precipitation (Liesegang phenomenon) of water vapor bubbles in solid silver, some interesting observations were made concerning the formation and growth of these bubbles. Under certain conditions it was found that the bubbles which formed in the single crystals led to the formation of large blisters ad cracks, and when poly crystalline specimens were used grain boundary cracking was observed. These two phenomena were examined in some detail, and it was found that an important step in the formation of the blisters and grain boundary cracks was the impingement of neighboring bubbles. DURING the study of Liesegang precipitation in solid silver,' some interesting observations were made concerning the formation and growth of water vapor bubbles. The bubbles were formed by annealing oxygen-saturated silver in hydrogen. Because of the similarity of this phenomenon to the hydrogen embrittlement of tough pitch copper,' it is known in the literature" as the hydrogen embrittlement of silver. In some respects it appears that the hydrogen embrittlement of silver is similar to the processes of hydrogen attack of steel5 and blister formation.' Hydrogen attack results from the high-temperature reaction of hydrogen with dissolved carbon or carbides in the steel to form methane (usually at grain boundaries). Blister formation occurs in steel and other materials as a result of hydrogen produced by corrosion, pickling, and so forth. Because of these similarities, some speculations were made concerning these other processes. EXPERIMENTAL PROCEDURE Water vapor bubbles were formed in 99.999+, 99.99+, and 99.9 pct Ag by annealing in a partial pressure of oxygen (pq) until saturated and then in a partial pressure of hydrogen (pH,). The hydrogen diffuses into the silver and reacts with the dissolved oxygen to form water vapor which precipitates in the form of bubbles. The specimens were then sectioned, silver-plated, mounted in cold-setting plastic, ground and polished through a preliminary polishing, and finally chemically polished.' The bubbles were visible without etching.

Jan 1, 1969

By Robert M. Jimeson

The competitive market potential for solvent refined coal is estimated. Market advantages of solvent refined coal are enumerated. Markets are possible in combustion, railroad locomotion, and carbon electrodes. The combustion characteristics are consistent with expected air pollution restrictions on the emission of sulfur and particulate matter. A market potential of sufficient size exists to support the initiation of solvent refining in the United States. The market analysis should help fuel producers determine the advisability of their undertaking the solvent refining of coal.

Jan 1, 1969

By R. A. Corley, W. R. Wilcox, J. R. Teviotdale

Chemical vapor deposition of hafnium carbide yielded whiskers, needles, dendrites, faceted crystals, and adherent coatings. The gas stream compositiom and the mass transfer conditions determined the habit of the deposit. The deposits were obtained at temperatures ranging from 1100" to 1800°C. HAFNIUM carbide has the highest melting point of any binary compound; therefore, its various potential applications are a subject of vital interest to the aerospace industry. The experiments described herein were performed to investigate the chemical vapor deposition of hafnium carbide with particular interest being placed upon the possible production of high-strength single-crystal whiskers for composite materials. In 1931 Moers 1 used a gaseous mixture of HfC14, Hz, and toluene to vapor deposit crystalline hafnium carbide on a tungsten filament heated to 2400°to 2800°C. More recently Lepie 2 deposited hafnium carbide on graphite using HfC14 and methane in a helium gas carrier. The pyrolytic depositions described here were accomplished in graphite tubes by using various gas mixtures and dopants. The resulting crystal habits included whiskers, needles, needle dendrites, bulbous dendrites, faceted crystals, and smooth, adherent poly-crystalline layers. EXPERIMENTAL The depositions were carried out in an induction-heated graphite tube, 1.2 cm ID, which was contained in a vertical 9-cm-ID quartz tube. (A more detailed account of the experimental procedures and results is given in Ref. 3.) Refractory oxide fiber and tubes and graphite felt were utilized jointly and singly for therma1 insulation. A typical temperature distribution is shown in Fig. 1. The reactant gases were introduced at the top and removed at the bottom of the tube. Table I summarizes the experimental conditions and results. Many deposition habits were obtained. X-ray analyses showed that they possessed the hafnium carbide structure. Almost invariably these formed well above the point of maximum temperature in the graphite tube. The habit depended strongly on the gas composition. In a series of runs (e.g., run A) using HfC14 and toluene in H 2, hafnium carbide coatings, Fig. 2, were reproducibly obtained at the position where the tube wall was 1400°C, and bulbous dendrites, Fig. 3, were

Jan 1, 1969

By H. T. Kennedy, J. E. Little

An empirical equation for the prediction of the viscosity of several pure paraffin hydrocarbons and nitrogen is presented. It involves temperature, pressure and six constants of the material, and it applies reliably to both liquids and gases. The equation is similar in form to van der Waal's equation of state. For the paraffin hydrocarbons methane through r-hexane and nitrogen, an average absolute deviation of 1.9 percent was obtained on 1,006 data points described in the literature by 14 authors. When this equation is extended to complex, liquid hydrocarbon mixtures, a correlation was obtained with an average absolute deviation of 9.9 percent. INTRODUCTION Equations describing the flow of gas and liquid through porous media contain the viscosity coefficient of the fluid. If other pertinent variables remain constant, the volume rate of flow is inversely proportional to this coefficient. In dealing with condensate fluids and volatile oils, however, the compositional effects resulting from changing pressure materially affect the viscosity. The effect of compositional changes also may be significant in certain secondary recovery or pressure maintenance processes, notably miscible displacement or gas injection. Early attempts to describe the performance of reservoirs utilized a volumetric material balance method wherein gas and liquid in the reservoir were identified as produced gas and liquid at the surface. This method of analysis proved adequate for reservoirs at moderate temperature and pressure that contained gas with moderately low amounts of condensable materials. The volumetric material balance procedures for "black oil" reservoirs leave much to be desired when applied to condensate and volatile oil reservoirs because phase behavior and compositional changes are relatively more important in these cases. The alternative is a compositional material balance, which in turn, requires a correlation of properties of the reservoir fluid with composition. This paper supplies this correlation in regard to viscosity, for reservoir crude oils. REVIEW OF LITERATURE The literature contains many empirical equations describing the effects of composition, temperature and pressure on the viscosities of pure liquids and binary liquid mixtures. However, the applicability of a majority of these equations is limited to very low pressures and to a small number of systems. Most of them, when applied to complex hydrocarbon systems, are of little value. The lack of utility of the majority of equations results from the fact that they were developed to show the separate effect of temperature, pressure or composition on viscosity, but not to predict the viscosity as a function of all three variables. And with the few exceptions noted below, they were developed to apply to much simpler systems than hydrocarbon mixtures. Eakin1 developed an equation for the viscosity of pure light hydrocarbons applicable in the gas, liquid and dense fluid regions, and in its most general form is written as µ - µo =A(ebP - e-cpk) The pure component viscosity at atmospheric pressure and temperature T, µo, was calculated using the Sutherland equation: µo = BT3/2/T + S The constants in Eakin's equation permitted the term e-CPk to become quite small at high densities (above 0.215 gm/cc), and the general equation would simplify to

Jan 1, 1969

By Rex B. McLellan, W. A. Oates

FROM a consideration of the application of the Gibbs-Duhem equation to multicomponent systems arken' derived the following equation applying to dilute solutions of a solute, 2, dissolved in a binary solution, 1-3:

Jan 1, 1969

This paper reviews the manpower requirements of the Australian mining industry. It has been necessary to provide general background information in order to support the view that university education in mining and mineral process engineering should be strengthened rapidly in Australia to provide graduates for the industry.

Jan 1, 1969

By M. Bevis, E. O. Fearon, P. C. Rowlands

Fe-Ni and Fe-Ni-C martensite specimens have been deformed in compression at room temperature and the habit planes of operative deformation twins determined by two-surface optical trace analysis. The full orientations of the martensite crystals were determined from divergent X-ray beam diffraction patterns. The experimental results are in excelled agreement with predicted twinning modes. In particular, the habit planes of some deformation twins in bcc martensites are consistent with a "Type XI compound'' twinning mode with Kl, Kz, 71, 77~ elements given by {5, 8, 11) {ioi}, (33) (ill) Tetragonal derivatives of this mode are operative in bct martensites. UnUSUAL deformation twinning modes have been reported by Richman' to occur in Fe-Ni-C martensites with bcc and bct structures. The twin habit planes were determined by single-surface trace analysis (pole locus method) and the remaining twinning elements were determined from the geometry of twin-twin intersections. The indices assigned to the observed habit planes are (3 101, "(089)" and "{0, 1,13)" or "{1,2,7} ", and only in the first case do the twinning elements correspond to a predicted twinning mode. This is mode 1.4 in the paper by Bevis et al. The results presented in Ref. 2 indicate that previously unpublished bcc and bct modes should be operative in preference to the (130) mode and anomalous modes reported by Richman. In view of these results and the uncertainties involved in determining habit planes from single-surface trace analysis and twinning elements from twin-twin intersections5 a two-surface trace analysis of deformation twins in Fe-Ni and Fe-Ni-C martensites has been carried out. EXPERIMENTAL PROCEDURES Two alloys with compositions Fe-23 pct Ni-0.6 pct C and Fe-30.4 pct Ni were prepared from 4N pure materials by induction melting under a vacuum of 10"5 mm Hg. The alloys were homogenized at 1350'~ for 5 days. Both of these alloys are austenitic at room temperature with M, temperature - — 50"C. The aus-tenite grain size of the Fe-Ni-C alloy was approximately 300 to 400 p. The Fe-Ni alloy was remelted in a vertical tube furnace and the melt lowered slowly from the hot zone of the furnace to produce s ingle -crystal austenite specimens. Specimens approximately 10 by 5 by 5 mm were cut from the ingots and quenched to various temperatures below the Ms temperature. The specimens were elec-tropolished in a 10 pct perchloric acetic electrolyte before being deformed in compression at room temperature. Martensite plates which exhibited profuse deformation twinning were selected for analysis and the specimen polished on a second surface such that the two surfaces which contained the martensite plate enclosed an obtuse angle of approximately 145 deg. The specimens were then electropolished to reveal the traces of the deformation twins on both surfaces. The full orientations of the martensite crystals were determined using a divergent X-ray beam technique (Kossel line technique) employing an AEI SEM2 electron probe microanalyzer. Details of this technique which include a detailed description of the Kossel camera attachment to the microanalyzer used in the present experiments have been discussed elsewhere.3 Only additional details relevant to this investigation are discussed here. The specimens were mounted with one surface normal to the incident electron beam as illustrated schematically in Fig. 1. The martensite plates to be analyzed were located using the normal scanning equipment of the microanalyzer. The position of the electron beam and hence the position of the source of divergent X-rays generated within the crystal could be located to within 1 p. Exposure times of approximately 8 to 10 min were required for back-reflection Kossel patterns and it was found that useful diffraction patterns could be obtained consistently from heavily deformed martensite plates. A reference line (carbon contamination mark) produced on the two surfaces of the specimen by scanning the electron beam in a direction having a known relationship with the reference !ine in the X-ray camera enabled the full orientation of the crystals to be determined. Martensite plates with widths as small as 8 p could be oriented using this procedure. The Kossel line patterns were interpreted using the charts developed by Rowlands and ~evis~ as generally

Jan 1, 1969

By Ashok K. Kakar

THE occurrence of superplasticity in Al-Zn alloys is of interest because of its possible industrial exploitation.' The eutectoid composition (78Zn-22A1) has been the most extensively studied;'-= neck resistant flow and high strain rate sensitivity of flow stress (characteristic of superplasticity) are associated with a micron-size grain conferred on the alloy by an homo-genization and quench.5'6 Compositions away from the eutectoid have received comparatively little attention, especially from the viewpoint of relating the structural

Jan 1, 1969

By J. D. Verhoeven

In the past 15 years a considerable amount of experimental and theoretical work has been done concerning the onset of convection in liquids as a result of interm1 density gradients. This work, which has been doue in many different fields, is reviewed here and extended slightly to give a rrlore quantitative understanding to the probletrz of conzection in liquid metal dlffusion experinletzts. In liquid metal systems the capillary reservoir technique is currently used, almost exclusively, to measure diffusion coefficients. In this technique it is necessary that the liquid be stagnant in order to avoid mixing by means of convection currents. Convective mixing may result from: 1) convection produced as a result of the initial immersion of the capillary; 2) convection produced in the region of the capillary mouth as the result of the stirring frequency used to avoid solute buildup in the reservoir near the capillary mouth; 3) convection produced during solidification as a result of the volume change; and 4) convection produced as a result of local density differences within the liquid in the capillary. The first three types of convection have been discussed elsewhere1-a and are only mentioned for completeness here. This work is concerned only with the fourth type of convection. Local density differences will arise within the liquid as a result of either a temperature gradient or a concentration gradient. It is usually, but not always, recognized by those employing the capillary reservoir technique that the top of the capillary should be kept slightly hotter than the bottom and that the light element should be made to migrate downward in order to avoid convection. In the past 15 years a considerable amount of work, both theoretical and experimental, has been done in a number of different fields which bear on this problem. This work is reviewed here and extended slightly in an effort to give a more quantitative understanding of the convective motion produced in vertical capillaries by local density differences. The Stokes-Navier equations for an incompressible fluid of constant viscosity in a gravitational field may be written as: %L + (v?)v = - ?£ + Wv - g£ [1] where F is the velocity, t the time, P the pressure, p the density, v the kinematic viscosity, g the gravitational acceleration, and k a unit vector in the vertical direction. A successful diffusion experiment requires the liquid to be motionless, and under this condition Eq. [I] becomes: where a is the thermal expansion coefficient [a =-(l/po)(dp/d)], a' is a solute expansion coefficient [a' = -(l/po)(dp/d)], and the solute is taken as that component which makes a' a positive number. Combining with Eq. [3] the following restriction is obtained: Since there is no fixed relation between VT and VC in a binary diffusion experiment, Eq. [5] shows that the condition of fluid motionlessness requires both the temperature gradient and the concentration gradient to be vertically directed. Given this condition of a density gradient in the vertical direction only, it is obvious that, as this vertical density gradient increases from negative to positive values, the motionless liquid will eventually become unstable and convective movement will begin. The classical treatment of this type of instability problem was given by aleih' in 1916 for the case of a thin fluid film of infinite horizontal extent; and a very comprehensive text has recently been written on the subject by handrasekhar.' It is found that convective motion does not begin until a dimensionless number involving the density gradient exceeds a certain critical value. This dimensionless number is generally referred to as the Rayleigh number, R, and it is equal to the product of the Prandtl and Grashof numbers. For the sake of clarity a distinction will be made between two types of free convection produced by internal density gradients. In the first case a density gradient is present in the vertical direction only, and, since the convection begins only after a critical gradient is attained, this case will be called threshold convection. In the second case a horizontal density gradient is present and in this case a finite convection velocity is produced by a finite density gradient so that it will be termed thresholdless convection. Some experimentalists have performed diffusion experiments using capillaries which were placed in a horizontal or inclined position in order to avoid convection. These positions do put the small capillary dimension in the vertical direction and, consequently, they would be less prone to threshold convection than the vertical position. However, if the diffusion process produced a density variation, as it usually does, it would not be theoretically possible to avoid thresh-

Jan 1, 1969