Search Documents

By John O. Farmer

The wire-line tubing perforator is a mechanically operated tool that is run on an ordinary steel measuring line into the tubing of a well, under pressure, to drive into the wall of the tubing, and securely lock in place, a tapered, cylindrical insert containing an orifice. Use of the perforator obviates the necessity of pulling and rerunning the tubing to install jet collars or flow valves, reduces the cost, and simplifies the task, of placing an oil well on gas-lift operation. More important, however, is the use of the tool with a removable check valve and stop, to provide a means of washing drilling mud from the annulus between the tubing and casing, and to complete the well for gas lift operation without exposing the producing formation to the mud column and without moving the tubing string. This paper discusses the origin, development, and mechanics of the wire-line perforator, the various purposes for which the tool was designed, and the method of selecting orifice sizes for any depth, and gives the results obtained thus far in practical application. Origin and Development Several years ago, a tool that could be lowered on an ordinary steel measuring line into the tubing of a well under pressure was designed and constructed for the purpose of punching a hole in the tubing walls above a shale bridge that had completely plugged the tubing of a well in the Long Lake field, East Texas. The well was in a low, swampy area, which excessive rainfall had caused to be in- accessible by car or truck for about four months. The only equipment at the well site consisted of an ordinary steel wire line that had been carried there to measure the depth of the bridge. Since a pulling unit could not be moved to the well site, and as the pressure on the casing was 2100 lb. per sq. in., it became apparent that the only way out of the predicament was to make a perforating tool that could be lowered into the tubing on a measuring line and operated under Pressure. Thus, the first wire-line tubing perforator was designed and built as an expedient, and was not used extensively until it had been redesigned to meet more frequent and increasingly urgent needs. Until recently, it was necessary to pull the tubing to install jet collars or flow the when a well was to be placed On gas lift. Because most companies either maintained or had access to pulling units and crews for this work, little or no thought had been given to eliminating or even simplifying this task. When the manpower and steel shortage became so acute, however, many operators suddenly found themselves without facilities to equip their wells for gas lifting. The wireline tubing perforator already had been tried and proved successful, therefore operators immediately requested its use to punch gas-jet holes in the tubing, to eliminate the pulling and running of tubing strings. The first deficiency revealed by more general use of the perforator lay in the inability to regulate the size of the hole punched through the tubing. The size could not be controlled to any degree of

Jan 1, 1946

By George R. Elliott

Methods are presented for measuring and comparing "degree" of water drive, and for observing the control that rate of withdrawal exerts over decline of reservoir pressure. Degree of water drive is studied from pressure-production curves of 10 reservoirs; the method used to present these comparatively is to convert cumulative oil production from barrels to percentage of ultimate. Degree of water drive is also represented by a "water-encroachment factor," representing barrels of water influx per pound-month per acre-foot of oil reservoir. Pressure-production curves for the water-drive reservoirs after a period of declining pressure show a diminishing angle of slope, in some cases to the point where pressure ceases to decline or where it even increases; the shapes of these curves are in marked contrast to the dissolved-gas type of curve, which shows a general trend toward zero pressure at ultimate oil recovery. Yearly rate of oil production in percentage of ultimate oil recovery is correlated with pressure decline. The correct rate of production of oil with its associated gas and water sustains pressure in reservoirs having a high water-encroachment factor. For reservoirs having a low water-encroachment factor, it is necessary to inject the produced water and even inject large volumes of water from an outside source. The discussion of the actual reservoirs is preceded by a general review and is followed by a substantial bibliography. It is now generally accepted that water drive is capable of yielding 60 to 80 per cent of the original oil in place in most reservoirs, as compared with 20 to 40 per cent for dissolved-gas drive. There is no need to question the importance of controlling a reservoir in order to take advantage of such an efficient mechanism. What is a water-drive reservoir? Oil reservoirs usually combine two or more of the four basic mechanisms: dissolved-gas drive, gas-cap drive, water drive, gravity drainage. A water-drive reservoir is one in which water advances to take the place of the oil and gas produced. When the oil withdrawal rate is sufficiently low, the water will tend to maintain pressure. The maximum effectiveness is attained when the water follows the oil withdrawal so closely that little or no decline in pressure occurs. Oil in its underground reservoir is associated with water. This water is significant in the production of the oil according to the source of supply and the permeability of the surrounding formation. As oil is produced and the pressure is lowered, water can move in to replace the oil. With adequate supply and sufficient permeability, actual movement takes place on an extensive scale. The first movement of water takes place by expansion of the water and its associated fluids. While this expansion is of little importance in some fields, in others it is sufficient to supply all of the energy required for the production of oil. When a pressure differential has been established

Jan 1, 1946

By M. A. Westbrook, J. F. Redmond

A method is presented for obtaining porosities of consolidated formations from the drill returns. The method provides a means of determining the bulk volume of a large number of particles, such as drill cuttings, by employing a capillary diaphragm for removal of surplus surface liquid from saturated cuttings having pores of capillary size, which reduces tile amount of error present in former attempts to determine the porosity of drill cuttings. The method makes it possible to obtain a considerable amount of supplementary data on consolidated formations. Introduction Porosity is a direct measure Of the volume of the voids in a formation. It may be used for estimating the permeability of a formation provided that a correlation of these two properties has been obtained from the analysis of cores from the particular formation, and it forms a desirable aid in interpreting electric logs.1 These useful applications have emphasized the importance of developing a method for determining the porosity of the formations penetrated by a well by some means other than coring, for even in exploration wells it is neither economical nor practical to core all formations. Also, in wells where at the outset the coring program appears comprehensive, it is frequently found that, after certain layers are drilled. more complete information is required for evaluation. Porosity values, if obtainable, would be of great assistance in such cases. In soft formations it is usually possible to obtain porosities after drilling with cores taken by side-wall coring devices. In hard consolidated formations, that coring procedure is not alway practicable and other methods for determining porosities must be resorted to. A first choice is the examination of drill cuttings. if an analytical procedure is available that is both accurate and reasonably rapid. Such a procedure has been devised and is applicable to sand and limestone cuttings having pores of capillary size. Although imp,ovements can yet be made, it is believed that the new technique is sufficiently well developed to warrant description, Preparation of Sample The well samples containing the cuttings representative of the particular intervals are first washed through a No' 6 gauge screen. The cuttings remaining on the Screen are large enough to use lor the porosity measurements' From the sized sample, the cuttings to be examined are separated from the shale and Other extraneous particles. It is recommended that 10 to 15 c.c. of the selected cuttings be used for measurements, although only 4 to 5 c c. were used to make the comparative tests described later in this article. These cuttings are extracted and dried by the same methods used for preparing core samples for porosity and other measurements. The separation, which is at present being carried out by hand, is the most tedious

Jan 1, 1946

By A. C. Bulnes

This paper applies the methods of statistical analysis to the interpretation of core analysis data of dolomitic limestone from the San Andres formation at Wasson and the Clearfork formation at Fullerton. Probability relationships are shown to connect the porosity and the permeability and the porosity and the fluid saturation. For example, the porosity-permeability relationship expresses the probability that a sample of porosity,f, will or will not be permeable. The over-all porosity frequency distribution of the reservoir together with the frequency curves of permeability (one for each class interval of porosity) provide a precise basis for computing the weighted average productive porosity of the reservoir for any assigned value of the minimum productive permeability. The probability that the permeability of a core specimen from Fullerton will exceed a given value appears to be dependent on the percentage porosity of the specimen, its void structure type (i.e., porosity in the qualitative sense), and the given value of the permeability. If continuous profiles of void structure type and porosity are available together with the appropriate porosity-probability of permability plots, the nes pay thickness may be estimated. The Invasion Index of a well is defined in terms of the porosity and permeability data. This index is suggested as a basis for comparing wells as regards their suitability as fluid-injection wells. Three problems of importance in the exploitation of limestone reservoirs may be stated as follows: 1. The determination of the productive porosity of the reservoir. The productive porosity is defined as f = fPVP/V [II in which Vp, is the volume of the reservoir that is sufficiently permeable to oil to give up an appreciable fraction of its original oil in place during the economic life of the reservoir; fp, is the arithmetic mean porosity of the permeable volume v*, and V is the total volume of the reservoir. 2. The determination of the number of feet of oil-bearing porous rock that will produce at a commercial rate into the well bore; i.e., the net pay thickness. 3. The choice of fluid-injection wells in a secondary recovery program. The ultimate recovery of the reservoir is proportiona1 to the productive porosity. The productive capacity of the well is proportional to the net pay thickness. The principal purpose of this paper is to show that the methods of statistical analysis when applied to core analysis data of dolomitic limestones offer a useful approach to the solution of these three problems, as well as others of importance in reservoir engineering. The use of these methods was suggested by the work of Jan Law.1

Jan 1, 1946

By Warren J. Jackson, John L. P. Campbell

Automatic recording of the radioactivity of the earth's formations provides a log of relative intensities that, if properly interpreted, can be applied to oil-field engineering. Production, engineering, and geological departments regard the radioactivity log as a forward step in the securing of more conclusive information for successful well completions. Explanations of the technique, together with some of the problems to which radioactivity logging have been applied, are presented in this paper. Introduction Those responsible for the completion of new oil and gas wells, or with planning workover operations on old wells, have followed closely the development of radioactivity well logging because they are interested in reducing the number of unknowns that usually are present in such work. Many operators have made use of the log, or are acquainted with at least one of the applications, but it is unlikely that any one operator is familiar with all of the many applications that are possible. The purpose of this paper is to present a representative example of each of the many applications, wherever the information has been released by an operator, and to illustrate by hypothetical examples other applications, releases for which have not been given. In this way, it is hoped that a better understanding of the scope of this new engineering tool may be obtained. Although the literature contains many references that describe in detail the theory, development, and application of radioactivity well logging, a brief discussion of the technique may be helpful to those who are investigating the subject for the first time. All rocks contain radioactive material in varying concentrations. In general, shales contain relatively more radioactive material than sandstones or limestones. These radioactive materials disintegrate with time into other materials of lower atomic weight, and in that process of disintegration the rocks are emitting many rays, the most penetrating of which is the gamma ray. The intensity of emission of the gamma ray is proportional to the quantities of radioactive materials present. A higher rate of emission would be observed, therefore, opposite a shale than opposite a sandstone or limestone. Since measurable intensities of gamma rays are capable of penetrating as many as five concentric strings of casing, and as the gamma-ray intensity is relative to the formations, the measurements of variations in gamma-ray intensities offer a means of identifying cased-off formations in their proper stratigraphic sequence. The Gamma-ray Curve The measurement of gamma-ray intensities is accomplished by means of an ioniza-tion chamber that consists of a heavy cylinder, about 3 ft. long, that contains two insulated electrodes and is filled with an inert gas under high pressure. Under normal conditions no current will flow through the gas when an electrical potential is set up between the electrodes, but when

Jan 1, 1946

By B. Otto Pixler

Mud-analysis logging provides identification of the fluid content of formations drilled by the rotary method and permits the accurate correlation of oil and gas shows with the depth. Mud-analysis logging eliminates much coring and has an especially important application in drilling programs when coring is particularly hazardous or the electric log is difficult to interpret correctly. An appreciation of the factors that influence the results of the mud analysis, such as rate of penetration, mud properties, coring, and characteristics of reservoir rock as related to the "flushing effect," permits a better understanding of the mud-analysis log. Recent studies of the relationship of the two gas readings obtained by the gas-detector instrument have proved significant. The difference between the total combustible gas reading and the higher molecular weight gas reading indicates the presence of methane. With few exceptions, zones not showing an increase of methane probably can be condemned. Mud-analysis logging furnishes valuable information, which generally cannot be obtained by other methods. Introduction Logging by mud analysis of wells drilled with rotary tools is a direct method of locating oil-and-gas-bearing formations. The use of this method of logging has increased each year until now more than 20 field units are being used in 13 oil-producing states and in some foreign countries. Several papers1-9 have been published in the petroleum trade journals describing in detail the equipment and the application of mud-analysis logging. This paper will discuss briefly the method and review its application and some of the late developments. Method As the drilling of a well progresses, the drilling bit dislodges and disintegrates a cylindrical section of the formation. If oil or gas is contained in the pore spaces of the cylinder, some of the contents of these porous spaces will be entrained in the drilling fluid. In wall logging by mud analysis, the mud is continuously examined for oil and gas on its return to the surface, and the results are correlated back to the actual depth of the hole at the time the mud was clearing the eyes of the bit. The test for gas is made by diverting a portion of the circulating mud from the flow line to a separator or gas trap, where the mud is thoroughly mixed with air and a portion of the gas entrained in the mud is removed. A stream of air is drawn coun-tercurrent to the flow of mud in the gas trap, thus materially assisting the separation of the gas from the mud. The air-gas mixture is then drawn into a "hot-wire" gas-detector instrument where the percentage of the combustible gas is determined. The presence of oil in the formation drilled is detected by a physical examination of the drilling mud under ultraviolet light. A sample of the mud is treated to reduce the surface tension and gel strength, after which it is placed in a viewing box. This box is so constructed that all external light is excluded and so that the sample may be subjected selectively to either ultra-

Jan 1, 1946

By Sherman L. Pease

An inexpensive and relatively rapid method that can be used by field crews is described. Fluid movement is determined by releasing a tracer (dye) in the well at a predetermined level and, after an interval of time, sampling the well fluid at another level. The testing equipment consists of a combined crusher and sampler unit that is run into the well on a wire line. The rate of movement can be calculated from time-volume relationships. Description of Method It is often desirable to determine whether there is occurring any transfer of fluid from point to point in a shut-in well, and, if so, to measure the rate of movement. When it is desired to examine a large number of wells for possible "thief" sands, the time and expense will be considerable unless the method used is inexpensive and rapid. After experimentation with several possible solutions to the problem, the Production Department of the Shell Oil Co., Inc., developed the apparatus described herein, which has proved satisfactory. Routine operations with it can be carried out by field production crews with a minimum of technical supervision and with negligible investment in equipment. The method is based upon releasing a suitable tracer in the well fluid at a known level, and recovering a sample of well fluid at another level after a measured interval of time. Repetition of this process with different time intervals between release and sampling gives the necessary data. For purposes of illustration, the setup for measuring migration of fluid in an upward direction is described in the following paragraphs. The arrangement of equipment is shown diagrammatically on Fig. I. The elements of the combination unit are the tailpiece, the crushing device, the spacer and the sampling device. The lengths of the tailpiece and spacer are varied to place the crushing and sampling devices in the desired positions in relation to the sands being tested. The crushing device breaks the glass bottle containing the tracer when the tailpiece strikes the bottom of the well and the tension on the sand line is slackened. Because of the open construction of the crushing device, the tracer is quickly and completely disseminated in the well fluid. The sampling device is a suction bailer, which obtains a sample of the fluid surrounding the perforated nipple just before the unit is picked up off bottom. The sample is retained in the barrel by the ball valve for examination at the surface. Normally, on the first run into a well, the sample is obtained near the releasing point of the tracer, and thereafter samples are taken near the base of the upper sand if migration is indicated by the dilution or absence of the tracer in the initial sample. The length of the time interval between the releasing of the tracer and the sampling of the well fluid is varied for successive runs, attempting first to establish the rate within limits and then to define it more accurately by additional runs if necessary.

Jan 1, 1946

By Walter Miller

BY the beginning of 1945 the output of petroleum products for war had reached a volume and a rate of growth which practically assured all requirements so long as war continued. The programs for making gasoline, lubricating oils of required quality, toluene for T.N.T., and chemicals for manufacture of synthetic rubber, as well as numerous other lesser petroleum products, were all well in hand, and unless catastrophic developments occurred there was no doubt of the ability of the industry to meet all demands. The end of the fighting found the refining industry working at top capacity on war commodities, but also in position to convert quickly into peacetime civilian production. 100-octane Aviation Gasoline Production of the vital 100-octane aviation gasoline, starting with approximately 44,000- bbl. daily capacity at our entry into the war, reached a top of 525,000 bbl. a day in the United States by the end of hostilities. With 75,- bbl. from other Allied sources, the grand total was 600,000 bbl., or 25,000,000 gal. each 24 hr. available to the armed forces had fighting continued. At times it was a close race between requirements and production, but never were any important military operations involving the use of high-octane aviation gasoline held up or delayed for lack of sufficient output of such material. The undivided effort of the entire refining industry in full cooperation with the Government made this record possible. Little diminution in output followed the German surrender on May 7. Plans called for a correspondingly greater activity for the Japanese war and possibly for well into 1946. But when the Japanese sued for peace on Aug. 10 most contracts were quickly canceled. Substantial stocks, reputed to be somewhere between 20,000,000 to 30,000,000 bbl., built up largely between V-E and V-J day pending organization of the larger Japanese war program envisaged after Germany gave up, were in the Government's hands in this country, in addition to working stocks in the war areas. Toluene and Lubricating Oil Requirements for toluene for T.N.T. increased rapidly as bombing speeded UP with increasing control of the air by the Allies in Europe and Asia. Production in excess of T.N.T. requirements which had been going into 1000-Octane aviation fuel blending during 1943 and 1944 was again drawn into explosive manufacture early in 1945. In anticipation of the war continuing into 1946, two new plants were ordered constructed, the decision being announced in April, plans calling for one of them to get into production about the end of 1945, the other in the first quarter of 1946. Both of these projects were later canceled as victory made it evident that the additional supplies would not be needed. Production was

Jan 1, 1946

Jan 1, 1946

By R. D. Heidenreich, R. E. McNulty, C. H. Gerould

Jan 1, 1946

By Helmut Thielsch

MeTallographic specimens whose surfaces are to be investigated are too thick to allow either light or electrons to pass through them for microexamination by transmission. This difficulty is overcome with optical microscopes by illuminating the surface through the objective lens. For electron microscopes best results are obtained by preparing thin replicas of the surface of the specimen, placing them in the microscope and passing the electron beam through them. Since electron microscopes represent a rather recent invention, they have found little application as compared with optical microscopes. This is true because, aside from the cost of new equipment and development of new techniques, some of the older replica methods necessitated the destruction of the surface from which a thin transparent replica was obtained. In other processes in which the surface is preserved, either too tedious a procedure is required, unsuited to "mass-production" requirements of industrial laboratories, or replicas of insufficient contrast and sharpness are produced. In general, investigations with the electron microscope involve five steps: (I) polishing the surface of the metal specimen, (2) proper etching of the surface, (3) preparing the suitable replica from the surface, (4) examination and phorography in electron microscope and (5) interpretation. Preparation of Metal Surfaces Usual metallographic polishing is generclly satisfactory. It is important though that the final polish be applied very carefully, since otherwise evidence of a small amount of deformation might show up even on relatively deeply etched surfaces. A high-power microscope should be used to determine the suitability of the polish and etch. This, of course, is not different from optical examinations, but in these, if a deep etch is used, the problem is less serious. It is frequently difficult to detect with optical microscopes poor polishing aside fiom superficial scratches before etching. Figs. I and 2 show micrographs of "well" and "poorly" polished nickel etched by immersing the sample for 20 min. in a solution containing 8 grams cupric sulphate in 40 C.C. of concentrated HCl and 40 C.C. of Hz0 (Marble's reagent). The sample shown in Fig. I was polished in its final stages for 5 min. on a carborundum wheel followed by ro min. on a rouge wheel, whereas the sample shown in Fig. 2 was polished only I min. on the rouge wheel. Generally, this procedure does not guarantee that the surface of the specimen will be either undistorted or deformed. It was applied here merely to show the effects Of good and poor polishing. To the experienced investigator, plastic deformation is

Jan 1, 1946

By Helmut Thielsch

During the last three decades a great many arguments have been presented on the subject of "mosaicJ' or "blockJJ structures of metals. Apparently because of insufficient evidence, the "block-structure" theories have never been widely understood among the physical metallurgists in this country, and most investigators among the few that have tried to demonstrate the existence of such an inner strutture Of crystals or grains have failed to recognize also the existence of a lamellar structure. Moreover, little thought has been given to justify the existence of such "lamellar" or "mosaic-block" structures on a theoretical basis. Since properties such as Plasticity; ferro-magnetism, hardness, diffusion, and others may be explained by structural faults in the lattice network of the crystals: the great importance of a more detailed knowledge of the structure within crystals or grains becomes now evident. Because Of the vast extent of the field Of submicroscopic structures, it shall be the purpose Of this paper only to review the more important of the results obtained by other investigators, especially in Germany, where a great deal of attention has been given to mosaic structure during the last three years. The origin of this mosaic patternt and effects of cold reduction and recrystallization will be shown in further studies later on. Imperfections in Crystals The many terms used in the literature to denote structural types of crystals are often not clearly defined. To clear up some of the confusion, the meaning of the more important terms will be given here. ideal, or perfect without any structural imperfections are called "ideal crystals,,or ''Perfect'' crystals,n meaning a Homogeneous interior structure of atoms, ions or molecules, as the case may be. In other words, at every point in the interior of the crystal exactly the same orientation of the crystallographic axes of the coordinate system would exist. The Surface of such a body, if etched with an appropriate etching reagent, would reflect light with perfect uniformity. Crystals of this type are almost nonexistent. Real Crystals.—L'Real crystals"' may contain various types of structural defects, which can be classified into: (I) lineage structure, (2) mosaic-block structure, (3) lamellar structure. The inhomogeneities many,in these groups mean that the orientation of the crystallographic aies will not be the same at every point within the interior of a crystal (or grain of a poly crystalline body). 'Perjecl Real Crystals.—The term "perfect real crystals " is generally used to describe crystals with minute structural or thermo-dynamical inhomogeneities. The former

Jan 1, 1946

By William Marsh Baldwin

TWO of the most useful and important equations available to the metallurgist for the study of plastic deformation of metals are the Huber-von Mises-Henckyl-~ and the St. Venant7-10 equations. Huber-von Mises-Hengky Equation The Huber-von Mises-Hencky equation answers the question: When does plastic flow occur in metal that is subjected to a multi-axial stress? It occurs, according to this equation, when the three principal stresses,t UI, u2, and u3 satisfy the equation: (<ri - <r2)2 + (<r2 - <rsY + (ff! - <r3)* = 2Ki [i] Here K is the yield strength of the material as determined in an ordinary tensile test. If the quantities ul, 52, andas are assigned to the coordinates of a Cartesian three-dimensional system, this expression describes a cylinder whose axis of symmetry is inclined at equal angles to the three coordinate axes4s6 (Fig. I). The radius of this cylinder is .\/%K. For the purpose of simplicity, it is sometimes advantageous to ascribe the values al/K = sl, az/K = s2, UD/K = SJ to the three coordinate axes instead of the principal stress alone. In this case, Eq. I becomes (*i - s*)1 + (s2 - S3)2 + (si - SiY = 2 [2] and the radius of the cylinder becomes \/%. In the latter method of representation, a point lying inside the cylinder indicates that the metal will react elasti-cally, whereas a point lying on the cylindrical surface indicates that the metal will behave plastically. Some of the geometric features of this cylinder are worthy of study. Let us inquire first as to what interpretation may be placed upon what we will choose to call the "circles of latitude" of the cylinder (L in Fig. I) and the "meridians" of the cylinder (M in Fig. I). Circles of Latitude Circles of latitude are formed by allowing a plane, passing perpendicular to the cylinder axis, to intersect with the cylinder. Any point, P, on this circle is presumed to have the coordinates sl, SZ, and s3. The coordinates of the point resulting from the intersection of the plane and the cylinder axis will be a, a, and a (since the cylinder axis is equally inclined to the three coordinate axes). L?t US now pass a line through the point on the circle and the point on the axis.

Jan 1, 1946

By Holbrook G. Botset

It is possible by means of the electrolytic model to simulate water-flooding or gas recycling systems involving input and output wells, and also the encroachment of a natural water drive. The results are obtained pic-torially, and by simple measurements and calculations the percentage of recovery is obtained qualitatively as a function of the total input. Introduction The increased demand for petroleum products, together with the decline in discovery rate and the higher cost of recovery as deeper formations are brought into production, has stimulated interest in methods for studying and predicting efficiencies of various production programs. Among methods Of recovery that have become of increased significance recently are gas recycling in condensate fields and secondary recovery by water-flooding. The electrolytic model is a useful device for studying such methods in the laboratory, at least in a qualitative way. The original experiments with electrolytic models and the development of their application to the study of secondary reCoverY problems were published in 1933. 1,2,3 Subsequently other investigators continued the development and modification of the bait method, with resultant improvements and extension of its applications.4-7 The method and equipment to be described here are thought to represent still further improvement in the results obtainable, with increased validity in their application to field problems. Sand OF Principles of Operation The underlying theory of the operation of the model is given in references I, 2 and 3. However, a brief statement of principles involved is given herewith. The applicability of the model is based on the fact that Ohm&apos;s law and d&apos;Arcy&apos;s law are exactly analogous; whence, electrical flow through a conducting medium may be used to simulate homogeneous fluid flow through a permeable medium. If two electrodes are placed in a conducting (ionized) solution and connected to the positive and negative terminals of a source of direct current, the positive ions of the solution will move toward the negative terminal, Since the velocity of an ion in an electrolytic medium is proportional to the electrical gradient, just as the velocity of a fluid particle in a porous medium is proportional to the pressure gradient, the motion of the ions in the potential field will be the same as the motion of fluid particles in a porous medium if the positive and negative terminals (input and output wells) and boundary conditions are made equivalent in shape and distribution. In order for the analogy to hold exactly, the sand must be assumed to have uniform porosity and permeability and the input

Jan 1, 1946

By T. H. Dunn, P. L. Menaul

This paper discusses the results of an investigation made to develop a method of combatting corrosion of subsurface oil-well equipment caused by brines containing hydrogen sulphide. Carbon monoxide, aldehydes, and certain cyanide compounds were found by laboratory tests to effectively inhibit corrosion of steel by sulphide brines. Experiments were made for one year in eight wells in West Texas fields using formaldehyde as an inhibitor. It was found that the inhibitor treatment successfully prevented the severe corrosion previously experienced in these wells, and effected important net savings in operating costs. Introduction Corrosion of oil-field equipment has long been a problem in areas producing sour crudes. These areas include the major fields of Arkansas, Western Kansas, West Texas and New Mexico. Corrosion in these fields is caused primarily by the chemical action of hydrogen sulphide in the presence of water and by electric currents entering the wells through flow lines. Hydrogen sulphide is noncorrosive to iron or steel in the absence of water but under the usual conditions prevailing in oil wells where more or less water is present, hydrogen sulphide is very corrosive. This type of corrosion occurs over the pH range below 9, which includes all natural oil-field brines. If air is present in addition to hydrogen sulphide and water, corrosion proceeds at an extremely rapid rate. It was reported several years ago that a string of oil-well tubing was literally dissolved within 50 days where an air lift was used on a well producing considerable water and hydrogen sulphide. Air is generally absent in wells producing sour crude. After hydrogen sulphide corrosion starts, it proceeds with increasing severity and its correction becomes progressively more difficult. This characteristic of sulphide corrosion has been attributed to the formation of galvanic couples between the iron and steel equipment on one hand and the products of corrosion on the other.&apos; Severe corrosion of subsurface oil-well equipment leads to a multitude of troubles. In addition to destruction of costly equipment, producing sands often are damaged by flooding with water leaking through corroded casing; bad mechanical conditions may develop in a well due to obstructions caused by corroded equipment lost in the hole, or partly collapsed casing; pumping operations are interfered with, and severe emulsification problems may result from the homogenizing action of corroded balls and seats.% A typical case of severe corrosion caused by hydrogen sulphide was reported in Howard County, Texas, where it was necessary to pull tubing once a week to repair leaks after the tubing had been in use for only one year. On one well in this area a string of tubing was pulled 11 times in 8 months; 11 joints of tubing being replaced because of leaks. In Ector

Jan 1, 1946

By Willis R. Battles, William F. Cerini, P. H. Jones

A test for determining the plugging characteristics of an oil-well injection water has been developed. It consists in measuring changes of the filter rate of a water at constant pressure with cumulative throughput when passing the water through a medium grade sintered glass disk. Application of the test method was made to the water used in the Union Oil Company&apos;s experimental water flood of the Chapman zone in the Richfield field, Orange County, Callfornia. This water developed increasing plugging tendencies upon aging, even though the finished water from the plant filter exhibited few such characteristics. The plugging material was found to consist of calcium carbonate, ferric hydroxide, and organic substances that were presumed to be bacterial. Various method of stabilizing this water to prevent the formation of plugging material were attempted. Lowering the pH to approximately 6.4 by injecting carbon dioxide provided a moderately satisfactory means for stabilization but a better method of stabilizing this water was found to be first aging and then filtering. Introduction An experimental water-flood project was started on the Chapman zone of the Richfield field in March 1944 and has been described in a previous paper.&apos; It consists of a single injection well drilled between old producing wells. A water-treating plant using primary alum flocculation, sedimentation and chlorination followed by secondary flocculation, sedimentation and fltration is employed to process the water before in@ion. In all of the water-treating operations, the system is open to the air, and no attempt is made to prevent the loss of carbon dioxide or absorption of oxygen by the water. The clear water is stored in a covered concrete basin and pumped through a Transite line to the suction of a high-pressure pump at the injection well&apos; The high-pressure tubing in the well to the injection zone is cement lined. The untreated injection water is a mixture produced with the oil from the Chapman and Kraemer zones and is supplied from the disposal system. Because the injection well was relatively deep (injection zone about 3400 ft.) and would be expensive to replace, it was believed imperative to supply a nonplug-ging injection water and to develop laboratory procedures for evaluating the treated injection water with respect to its formation plugging properties. This report describes the development and application of the test procedure based on the assumption that the plugging properties could be determined by measuring the progressive decrease in flow rate of the water through a porous medium. If the quality of the injection water was good enough so that the plugging action on the porous medium was of small magnitude, it was reasoned that the tendency to impair flow in the formation would not be serious.

Jan 1, 1946

By David J. Mack

A survey and critical appraisal of published information about Young&apos;s modulus was originally made by the writer because of a complete lack of information about this very important quantity in works on. mechanics, physical metallurgy, physics, and other sciences. It was felt that a comprehensive summary of such information about Young&apos;s modulus might be of general interest and may suggest new problems or lines of attack on other problems that involve E. Hence this paper has been prepared even though it is only a review, with no new ideas or experimental data. The references are only those used in assembling the paper. No attempt was made to compile a complete bibliography on the subject of Young&apos;s modulus. CalculatioX oP YouNg&apos;s Modulus from Theoretical or Empirical CoNsidera-tions Many attempts have been made to compute E from theoretical considerations. The earliest calculations were probably those of Tomlenson (1883) and Souther-land (1891), but Fess&apos;enden4&apos;,~ made extensive calculations a few years later and arrived at the relationship: £ = 78.TOw(i)* where V is the atomic volume. In 1923, Peczalski, working from the same standpoint but with more information available on atomic structure, arrived at an identical relationship, which he expressed as: where B is a constant of value about 8 . 107, p is density and mis atomic weight; the atomic volume, of course, being ml p. Portevind4 immediately pointcd out that while the equations of Fessenden and Peczalski were true of the common metals, they gave low values for the refractory metals with high moduli (Fig. I). He showed (Fig. 2) that much better concordance was obtained by means of an empirical equation of the form: F- KT" where K is a constant; T the absolute melting point; V, atomic volume, and a and b constants of value approximately I and 2 respectively. This constant K in the Portevin equation is not necessarily the same for all elements, as shown by Thompson. Other equations for E based upon theoretical considerations have been derived by Honda and Yamada49 and Lasareff.50 The most recent calculations of elastic moduli based upon quantum mechanics are probably those of Fuchs He extended the method of Wigner and Seitz for calculating the lattice energy and compressibility of monovalent metals and computed the elastic constants of lithium, 18

Jan 1, 1946

By A. W. Ross, William Marsh Baldwin, T. S. Howald

The related subjects of preferred orientation, directionality in physical properties, and earing tendencies of wrought metal strip have attracted the attention of metallurgists to such an extent that in the past 20 years hundreds of researches have been published on this one general problem. The anisotropy of tensile strength and elongation have been exhaustively studied in their relationship to the occurrence of ears in cups drawn from strip&apos;-~O.~g and, to a lesser extent: yield strength7."-l7 and stress-strain curves&apos;5 have been investigated. Despite the tremendous fund of knowledge thus accrued, no simple quantitative correlation of directionality and earing tendencies has yet been found. In a sense, this is not surprising. The formation of ears in a drawn cup clearly is a special phase of the general study of metal flow; in particular (as will be brought out in the course of this paper), ears are due to anistropy in the rates of deformation of the metal in the radial, circumferential, and "thickness" directions of the original blank. It would be difficult to effect a correlation between caring tendency and a property that may be completely independent of the flow of metal, or at best related to metal flow in an exceedingly complex fashion. Yet, it is this correlation that has been attempted; tensile strength and elongation are attributes of metal rupture. a phenomenon that has quite admirably been shown to be distinct from the phenomenon of metal flow,21 while yield strength and stress-strain

Jan 1, 1946

By William A. Johnson

The mathematical analysis of diffusion curves in solid metals is carried out ordinarily by analogy with the flow of heat in a continuous medium and no account is taken of the fact that the materials involved are composed of discrete particles that move discrete distances at irregular intervals. It is possible to treat the problem on the basis of simple assumed atomic mechanisms, in which case, because of the small scale of the elementary process compared to the gross effects observed experimentally, the two procedures lead to the same expression for the variation of concentration with distance. Thus, for engineering purposes, the usual methods are quite satisfactory. If, on the other hand, our purpose is to go beyond the mere collection of data, however desirable this may be, it is necessary to recognize and understand the factors that are of fundamental importance. One factor that has not hitherto been considered when dealing with solid metals is the difference in atomic weights of the isotopes of a single metal. While all the atoms of a given element are alike chemically, their weights may vary by a small but significant amount, and atoms of different weights may have different diffusion rates. With gases this variation in isotopic weight produces a change in the rate of diffusion by a factor inversely proportional to the square root of mass. While, except for the lightest gases, this is not a large effect, it is, for example, sufficient to permit a considerable concentration of one isotope at the expense of others. If metals exhibit a similar phenomenon, some modification of the analysis of the diffusion process will be required, since the different isotopes of a given metal will have different probabilities of moving and the heat-flow analogy will contain a fundamental error. This situation cannot be rectified by using a diffusion coefficient based on the average probability of moving, and it can be shown that even when the diffusion coefficient is independent of composition, the diffusion curve will not agree with the simple theory except in the rare cases where only one isotope exists; e.g., gold. If, however, the mass effect in the solid state were no larger than in the gaseous, the errors arising therefrom in the analysis of ordinary diffusion curves would be quite negligible. Nevertheless, our desire to obtain all possible information concerning the details of the diffusion process, and the possibility of diffusion in the solid state as a means for separating isotopes are cogent reasons for undertaking an experimental study to determine whether isotopes of different masses diffuse at different rates. Experimental Procedure If isotopes of different masses diffuse at different rates, the ratio of the concentration of one relative to another will vary with the distance from the diffusion inter-

Jan 1, 1946

By G. E. McElroy

Though air jets occupy only a minor role in the ventilation of mines and other enclosures, their importance in this respect is greater than is commonly recognized and may be considerably increased as our conception of their modes of operation becomes clearer. The object of this paper is to discuss some of the ways in which air jets are involved in mine ventilation and some possible applications to the ventilation of mines and other enclosed spaces. The mention of air jets ordinarily suggests the use of some form of an air injector, such as the Venturi blower occasionally used for auxiliary ventilation in mines, or the Saccardo (injector) system used to a limited extent for ventilating railroad tunnels. Actually, the term covers such common phenomena as the discharge of air from fan pipes and coal-mine line brattices, and even from smoke stacks and fans. A knowledge of the general mode of air entrainment by jets also helps to explain certain phenomena—some mine-gas explosions, for instance—that otherwise would remain obscure. Jet action has been involved in three recent series of Bureau of Mines experi-ments in which the author has participated: experiments on fan-pipe discharge, On the dilution of gases discharged from a stack and On the ventilation of a ship&apos;s hold. Available data on the discharge of jets into large openings and on the design and performance of air injectors have been analyzed in considerable detail and supplementary experiments are planned for after the war. The results of the fan-pipe experiments have been combined with the analyses of data on jet discharge into large spaces, and have been published.&apos; The results of the stack-gas dilution tests, which refer to a jet discharged into a crosswind, have also been published2 and a paper on the design and performance of injectors has been prepared for publication.3 These technical experiments and analyses form the background and the documented evidence for the following nontechnical discussion of the use of air jets in mine ventilation. Jet Characteristics The jets commonly encountered are those in which the air is in turbulent— as opposed to laminar, or streamline-— motion. The characteristics under discussion apply only to such turbulent jets and have their basis in theories of the mixing of turbulent air currents. Such jets have basic characteristics that are present, though variable in form, regardless of whether the jet expands freely in space, whether the expansion is limited by adjacent walls, or whether the jet propels air through a flow circuit. They expand at definite angles and entrain the surrounding air, even though the entrained air must be obtained by recirculation of their own air streams. As the quantity of air in motion in the mixed stream increases, the average velocity of the stream decreases.

Jan 1, 1946