Search Documents

By Luiz Bruno de Oliveira Araujo, Luciano Morais Teixeira, Luiz Gustavo Pedrosa de Melo, Altair Lúcio de Souza

The off-line simulation of the metallurgical process in an industrial line brings several benefits such as: evaluation of the influence of the main parameters that affect the results of the process, comparison between different set ups, greater assertiveness in operational adjustments, process optimization and reduction tests for development of new products. With this objective, a software for offline simulation of the hot strip mill process of Gerdau Ouro Branco was developed based on the logic of calculations implemented in the online model. The software results in important process variables such as mill pass scale, load, torque, and power at each pass, temperature and the hot mean flow stress of the simulated material. During rolling mill process the strip presents different temperatures and time between passes for different points along the length, which directly influences the hot strength of the product and consequently in the calculated variables, thus the calculations executed by the software were divided to three points of the strip, head, body and tail bringing the individual results to each of these positions.

Oct 1, 2019

By Ronaldo Esteves Ribeiro, Jefferson Felipe Faria Clemente, Carlos Victor Francisco dos Santos, José Herbert Dolabela da Silveira

n recent years, the market for thick plates has been highly competitive, in this scenario the plates quality is a critical success factor. In this process, the quality of the cut in thick plates is one of the important requirements for the customers, by the visual aspect as well as the technical aspect of the plate application. In the shear line, the cutting is done by shearing to trim tips, subdivide plates, trim side edges, remove samples, eliminate defects, etc. The cut is obtained by the penetration of the upper knife in the plate, causing plastic deformation in a certain region and hardening. If the clearance between the knives is adequate, the cracks will be close to the centre of the plate thickness and will result in a good cut quality. This work will present the theory of cutting of thick plates, the types of shearing, the quality of the edge in the cut, the types and the main characteristics of the knives.

Oct 1, 2019

By Karl K. Bagger, Felipe Bertelli

The competitive scenario of steel industry requires studies and developments to improve manufacturing processes focusing on increasing productivity and reducing costs. The practice of coating rolls for cold rolling with the chrome aims to increase the rolling campaign, reducing their wear by increasing the surface hardness, which guarantees a greater homogeneity in the surface of the rolled products. The present paper presents a study on the effect of the chromium coat on a forged steel rolls on the wettability of a SkinPass solution. The hardness of the coated layer and the contact angle were measured for two concentrations of solution on two types of surfaces, comparing the coated and uncoated surfaces. The results show that there is an influence of the coating on the wettability of the fluid when comparison are made with chrome coated and uncoated materials, being verified through tests in Goniometer. The productivity of the coated rolls showed higher productivity than the uncoated ones.

Oct 1, 2019

By Delvaux Carlos de Miranda Sobrinho, Hegler Zurick Arantes Assunção, Marco Venicio Mendonça de Souza, Luciano Toledo Ribeiro

This paper aims to present the development of a 600mm U-Pile that was done in Gerdau’s Ouro Branco Heavy Section Mill in order to feed the local market with a product.The focus of this study is to show the developmental process the Mill went through until it was prepared for hot trials. All roll pass and guide designs were developed by our own team. Analytical tools like Finite Element Analysis and reduced scale lead trials will be shown and how these tools impacted on the development timeframe and accuracy of the final results on steel.

Oct 1, 2019

By Bruno Alves Resende, Antonio Adel dos Santos

Temperature, microstructure and dimensions are the main material parameters to be controlled during hot rolling of steel. Although thermal mathematical models have long been developed and applied for hot strip rolling, each Hot Strip Mill (HSM) must have its own model adapted to its facilities. Thus, a mathematical model for temperature evolution during rough rolling has been developed for the Usiminas HSM at Ipatinga Plant. The model achieved a high level of accuracy, which was assessed by comparing measured values of temperature at the hot strip mill entry with the calculated ones, the difference ranging from 9°C to 17°C. Application examples have shown that the slab can be occasionally stopped before start of rolling for as long as a couple of minutes without compromising its further processing. On the other hand, if the transfer bar stops after rough rolling even for short time, further processing in the HSM can be hindered, due to excessive temperature drop. In case of such abnormal line stop, the model can be used as a tool for decision-making to either continuing the planned rolling schedule or to changing the route, thus improving the overall rolling process.

Oct 1, 2019

By Mirko Jurkovic, Thomas Hueper, Jens Kempken

The high competition scenario pushes the steel producers business. Zero defect requirements from customers force the operators for additional efforts in process control and quality management. PQA® has been developed as an advanced process and quality management assurance solution. It is focusing on the analysis of process data, equipment information, inline quality measurement devices and trend analysis. The paper describes the structure of the advanced process and quality management assurance solution PQA®; it gives insights on the expert know-how, process and quality evaluation and points out the benefits like cost reduction, improvement yield and customer satisfaction increase.

Oct 1, 2019

By Antonio Augusto Gorni, Kenji Camey, José Herbert Dolabela da Silveira

Recently several studies have been developed on the use of microalloyed steels with low Mn content (below 1%) in the controlled rolling of heavy plates for the manufacture of pipes. However, this novel concept of alloy has peculiarities in its thermomechanical processing. Lower Mn contents should lead to the acceleration of NbCN precipitation kinetics during rolling, leading to a reduction in the soluble Nb content in austenite that delays its recrystallization by drag effect. This fact, plus the heavy and fast passes applied under virtually isothermal conditions in a heavy plate rolling mill with high power, increases the risk of partial recrystallization during the finishing stage of the controlled rolling, since strain hardening of austenite becomes significant and the interaction between precipitation and recrystallization is increasingly delayed. The objective of this study was to analyze the evolution of mean flow stress during the finishing stage of controlled rolling in these low Mn, high Nb microalloyed steels, in order to better understand the metallurgical mechanisms acting during this process and identify conditions that allow full compliance with the requirements of this product class.

Oct 1, 2019

By Juliano Braz Possatti, José Fagundes Júnior

This project involved a teamwork including process control, maintenance and operation specialists, R&D and CTO experts to identify and actuate on each opportunity to increase charging temperature, furnace efficiency, decrease discharging temperature when possible, decrease FM and RM cycle time (mainly speed increase and interpass time decrease), tracking zones optimization, safe use of equipment power limits, safety interlocks revision and tune models for Mill Pacing Control and Slab Design.As result of these efforts, ArcelorMittal Tubarão HSM today occupies a prominent position among the best HSM of similar layout and produced mix of the group and worldwide. This paper will show the path which was followed by the AMT HSM team to achieve more than a 20% productivity increase resulting in a hot coils production per year more than 700 million tons higher.

Oct 1, 2019

By Manfred Hackl, Sergey Bragin, Alois Seilinger

The demand for hot rolled strip is growing in multiple ways. To remain competitive, new and existing mills must meet arisen challenges in the best possible way. The production of hot strip is a key element of steel production. Since close to half of all steel produced is hot-rolled to strip, mills require maximum throughput and availability combined with geometrical precision and the ability to create optimum material properties. Today there is a clear trend in developing new steel grades with high-strength and improved formability, like 3rd generation AHSS (Advanced High Strength Steels), as well as a trend to produce thinner and wider gauges. This trend challenges hot strip mills because it requires new technologies which provide more flexibility in metallurgical treatment during the rolling process. In order to meet and promote these trends Primetals Technologies is currently working on different concepts and solutions. One example is the development of a new mill stand technology Flex-HI HOT which allows to adapt the last finishing mill stands by efficiently switching from 4-high to a 6-high mode with small work roll diameter based on production needs. Another solution is to apply a permanent 6-high rolling stand at the end of the finishing train. A smaller work roll diameter allows to achieve higher specific thickness reductions and deformation rates resulting in significant thinner hot-strip gauges with valuable metallurgical benefits. The developed solution concepts with technological and metallurgical benefits will be presented in this paper.

Oct 1, 2019

By D. A. Aranda-Regino, C. Gómez-de-la-Garza, J. Ramírez-Cuellar, L. A. Leduc-Lezama

The Pickling Line Tandem Cold Mill (PLTCM) at Ternium’s Pesqueria plant with a 5 stands, 6 high configuration started in 2013. At the time of the start up the work roll specification and grinding practices were stablished following a low risk policy to be able to sustain any start-up associated accident. Once a stable operation has been achieved both these policies are being modified to improve productivity and reduce costs. The specified hardness of the rolls has been increased and efforts are being made to optimize the grinding according to the rolling campaign length and materials. The fatigue damage in work rolls, after rolling and its removal by grinding was followed by hardness measurements made at the end of the rolling campaign and after grinding. Softening of the rolls after rolling was found mainly in final stands to be related to the averaged stress experienced during the campaign, the original roll hardness was recovered after grinding. Hardness evolution was also followed after each grinding step finding that the total amount of grinding could be reduced. The grinding practice was modified accordingly for the first stands and the yield of work rolls in them has improved.

Oct 1, 2019

By Daniel Wild, Tobias Scheffer, Marvin Laugwitz, Martin Jochum

Leveling is a standard process in the rolling mill to eliminate flatness deviations. The process layout is based on models and the leveling result depends on the accuracy of the material parameters in these models. Even small deviations from the correct assumptions can have a major effect on the final flatness. Thus, after leveling the products may look optically flat, but subsequent to a final cutting process springback occurs due to residual stresses. The objective of this work is to analyze the influence of material parameters and gravity on the flatness after leveling. To evaluate the sensitivity of the process, an FE parameter study is exerted that reveals the influence of fluctuations in material properties in the case that the leveling setup is fixed. Gravity is neglected to not conceal flatness deviations. Examples of this study are rerun in a further step under consideration of gravity to also analyze its influence on the resulting flatness and residual stresses. Finally, to analyze the consequence of the residual stresses, all information of the plate from the previous step are transferred while gravity is suppressed to prompt springback. This study revealed that slight deviations of the material properties can lead to uneven plates in simulations where gravity is not considered. If gravity is taken into account, the unevenness is concealed and the plate seems flat. A springback simulation of the same plate shows that strong residual stresses are still present and would lead to unevenness if e.g. the plate were cut.

Oct 1, 2019

By Yong Tian, Tian Zhang, Zhao-Dong Wang

To meet the requirements of high-performance steel plates, while reducing manufacturing costs and saving energy, the advanced cooling system for plate mill (ADCOS-PM) with functions of accelerated cooling (ACC), ultra-fast cooling (UFC), and direct quenching (DQ) was researched and developed by the State Key Laboratory of Rolling and Automation (RAL). Since 2003, several sets of ADCOS-PM device were developed and implemented in industrial practice. To fully utilize the ADCOS-PM technology, the combination of various strengthening mechanisms was promoted by NG-TMCP technology and low-cost, high performance plates were produced such as pipeline steels, and high-strength construction machinery steel.

Oct 1, 2019

By HaiWen Luo, Bin Hu

A ultra-high strength medium Mn steel with good ductility was designed and manufactured via the combination of warm rolling and V alloying, which produced not only the extensive precipitation of fine VC particles in both ferrite and austenite but also the bimodal size distribution of retained austenite (RA) grains. A substantial increase of yield strength up to 650 MPa was achieved due to the addition of V without deteriorating ductility. The coarse RA grains firstly transformed to martensite during yielding at the much higher stress threshold, followed by a significant work hardening due to dislocations multiplication, twinning-induced-plasticity (TWIP) and transformation-induced-plasticity (TRIP) in the ultrafine RA grains. The best combination of strength and ductility included 1.5 GPa ultimate tensile strength and 28% total elongation. This was achieved due to the sustainable TRIP and TWIP effects in the later straining stage resulting from the ultrafine austenite grains, the latter were reversely transformed from the recrystallized ferrite grains.

Oct 1, 2019

By Michel Rodrigo Luiz, Glaucio Augusto Polini, Leonardo de Souza Melo, Giovani Rodrigues, Giardini F. Lazzarin

ArcelorMittal's pickling and cold rolling line has been demanded to increase production since the installation of equipment in 2015. In addition to improving productivity related to these new equipment, several additional jobs were planned and executed on equipment already installed has been carried out in order to improve the efficiency of the line. The present work exposes what was done in the scale breaker (tension leveler) to improve the availability results of the section and consequently of the line.

Oct 1, 2019

By João Batista Ribeiro Martins, Érica Simões Rodrigues, Ramiro da Conceição do Nascimento Júnior, Marcos Tadeu D’Azeredo Orlando

In order to guarantee the quality of the sinter and process control some measurements are made such as RDI and FeO (Fe2+). However, the behavior of sinter during reduction in the blast furnace is not always understood, when it is analyzed only metallurgical, physical and chemical quality. Therefore, it is necessary to find alternative techniques to understand more this behavior. In this work four experimental trials were performed to obtain sinter samples with different FeO (Fe2+) contents. Optical microscopy was performed to identify and quantify the phases in sinter and to evaluate the magnetic behavior of each one, the Magnetic Susceptibility technique was used. The results obtained between Optical Microscopy, Magnetic Susceptibility and quality parameters were compared and then was identified that Magnetic Susceptibility may be an alternative to help the understanding of sinter behavior in Blast Furnace.

Oct 1, 2019

By Alain Denis, Marcelo Curtes Martins, Jeferson Rocio de Oliveira

In this work we present a study of optimization of a new inhibitor for turbulence pickling line. The efficiency of inhibition was measured and the weight of loss was evaluated in four different materials to optimize the dosage of the inhibitor. In seven months we had 8.7% of reduction in pickling losses.

Oct 1, 2019

By Michel Rodrigo Luiz, Glaucio Augusto Polini, Giardini F. Lazzarin

ArcelorMittal's pickling and cold rolling line has been demanded to increase production since the installation of equipments in 2015. In addition to the improvement in productivity related to these new equipment, one of them the automatic surface inspection system (SIAS), work has also been developed in other equipment seeking improvement of production indicators. The present article exposes the actions and gains that were achieved with actions on two equipments in the same section as the Side Trimmer. The first one deals with the optimization of time gains with sequencing adjustments without financial contribution, using only internal labor seeking reduction of unproductive times by adjustments of the side trimmer in the cold strip mill. The second item discussed demonstrates the actions and the gains generated due to the availability of new resources (installation of SIAS equipment), the optimization of these resources seeking a focus on the reduction of ruptures in the tandem cold mill, configuring the same in the aid of the identification of critical defects and also in the automatic speed reduction action of the tandem cold mill in defects considered serious. In both cases the intention was to improve production, seeking to improve the results of the section and the line.

Oct 1, 2019

By M. A. Mekicha, M. B. de Rooij, C. Pelletier, D. T. A. Matthews

One of the main factors that reduce strip cleanliness are iron fines, which are formed due to the abrasive interactions of the roll surface and the strip in the roll bite during cold rolling. They can cause a problem in fouling of the cold rolling mill as well as downstream processes. It has been repeatedly observed that chrome plating the work roll improves strip cleanliness. In the present work, scratch tests and reciprocating sliding tests were carried out under lubricated conditions to explore the influence of chrome plating on iron fines formation. Scratch tests were conducted to study the influence of chrome plating on iron fines formation at single asperity scale due to its intrinsic property. Reciprocating sliding tests were performed to study the influence of chrome plating a rough surface on iron fines formation, taking into account the initial roughness. The scratches made using chrome plated pins showed lower friction, generated less iron fines and exhibited lower material transfer. Reciprocating sliding tests done using the uncoated pins showed galling at different sliding distances depending on the roughness of the pin. On the contrary, reciprocating sliding tests with the chrome plated pins exhibited no galling irrespective of the roughness.

Oct 1, 2019

By Simon Chiartano

A global reflection on the design of blast furnace main runner was investigated in this paper. TRB Company used its skills and expertise to understand what the best option for this sensitive component is, including some innovative tools: intelligent block design for safety lining, thermal & thermomechanical numerical simulation, immersive measurement by thermocouples, IR thermal camera, 3D laser scanner.

Oct 1, 2019

By Amauri Garcia, Noé Cheung, André dos Santos Barros, Clarissa Barros da Cruz, Thiago Soares Lima, Rafael Kakitani

Materiais de interface térmica (Thermal Interface Materials - TIMs) são responsáveis pela troca térmica entre a fonte geradora de calor do processador integrado e o dissipador de calor. Devido ao seu baixo ponto de fusão, boa fluidez e cumprimento com as exigências de regulamentação (Restriction of Hazardous Substances - RoHS), ligas à base de bismuto têm sido investigadas para aplicação como TIMs de alta performance. Neste contexto, a análise das propriedades dessas ligas em função de parâmetros microestruturais torna-se, portanto, de elevado interesse científico e tecnológico para o setor eletrônico. Assim, este trabalho tem como objetivo desenvolver correlações entre propriedades de resistência à tração e a microestrutura da liga Bi-0,28%Ni solidificada sob um intervalo de taxas de resfriamento usualmente obtido em processos industriais. Por meio de microscopias óptica e eletrônica de varredura foi observada uma morfologia tipicamente eutética lamelar, composta por lamelas ricas em bismuto com o intermetálico Bi3Ni nos contornos. Os espaçamentos lamelares (λL) foram, então, correlacionados com os parâmetros térmicos de solidificação, sendo propostas leis experimentais de crescimento microestrutural. Ao fim, observou-se que, para λL < 101 μm, equações do tipo Hall-Petch caracterizam a variação do limite de resistência à tração e do limite de escoamento.

Oct 1, 2019