Search Documents

By Sangjian Zhang, Zhu Xiao, Lairong Xiao, Rushi Chen, Mei Fang, Zhou Li

The copper-graphite metal matrix composites were fabricated by two different production methods: directly sintering with copper and graphite (Cu-Gr composite), and in-situ sintering with cuprous copper and graphite (Cu2O-Gr composite). During the in-situ reaction sintering, a redox reaction occurs at the interface of the Cu2O particles and Gr particles, resulting in the improved physical and mechanical properties of Cu2O-Gr composites. Compared with Cu-Gr composite, Cu2O-Gr composite has a higher compression strength at any given graphite content due to the improved interface bonding and uniformly distributed fine graphite particles in the matrix. Increasing graphite content decreases the mechanical properties of the copper-graphite composites. The compression strength of Cu2O-Gr composite is 50-100 MPa higher than that of Cu-Gr composite. INTRODUCTION Copper-graphite composites have been widely used in industry due to their low density, relatively high strength and hardness, good thermal and electrical conductivity, arc ablation resistance and self- lubrication ability (Grandin & Wiklund, 2018; Han & Xu, 1999; Huang et al., 2017). Electric sliding contact friction pair in the high-speed railway system and motor brush in electric contact components have a very high demand on electrical conductivity and self-lubrication ability of materials. The electric devices need to bear both mechanical load and high electric current. Copper-graphite composites with good mechanical, electric and self-lubrication properties are the best candidates for application in multifunctional electric sliding contact frication components. The relative sliding speed of friction pair is developing towards 100 m/s or even faster, which can withstand the electric flow of more than 800 A, and it is often accompanied with vibration and impact (Guo & Ding, 2008). Conventional wear-resistant materials can no longer meet the current requirements and this promotes the development of copper- graphite composites with excellent comprehensive properties (Ding, Chen, Zhu, Zhang, & Zhou, 2009; Yasar, Canakci, & Arslan, 2007). There are many ways to fabricate copper-graphite composites, mainly including powder metallurgy method, liquid immersion infiltration method, rapid sintering method and electrodeposition method (Kalin & Poljanec, 2018; Kim, Lee, & Han, 2014; Liu et al., 2018; Wang et al., 2018). Each method has its own advantages and disadvantages, and the powder metallurgy method is the most commonly used one due to its simple process, high economic benefit, and industrial production applicability. The common steps of the powder metallurgy method are as follows (Samal, Parihar, & Chaira, 2013): firstly mixing the copper (copper alloy) powders and graphite with a certain ratio, following by die-forming, and then sintering at the high temperature with or without pressure. The advantage of copper-graphite composites is that the graphite distributed in the copper matrix uniformly and it can form a carbon diaphragm preventing the wear of the composite (Fu & He, 2010). However, the bonding strength of the interface between the copper matrix and the graphite is relative low as the combination between them is mechanical interlocking but not metallurgical bonding (Ma et al., 2008). It is meaningful to develop new fabrication technology of copper-graphite composites with better interface bonding, which could provide guidance for the design of copper-graphite composites with excellent comprehensive properties.

Jan 1, 2019

By I. Ueda, S. Ishikawa, T. Nagata

“O-SR process” in which the S-Furnace of the Mitsubishi process is followed by existing reverberatory furnaces (RFs) and Peirce Smith (PS) converters has been operated since December 2007. The S-Furnace smelts copper concentrates to produce molten matte containing 58-62%Cu which is then settled in the RFs and converted to blister copper in the PS converters. The SO2 gas generated from the S-Furnace and PS converters is converted to sulfuric acid in the acid plants. In addition to the smelting copper concentrates, the O-SR process has advantages in terms of recycling various waste/secondary materials. Automotive Shredder Residue (ASR) has been treated in the RF to reduce fossil-fuel consumption in RFs, and to recover various metals included in ASR as well, since 1993. Electronic circuit boards (E-scrap) has also been processed in order to recover not only copper but also rare resources such as gold, silver and PGMs since 2013. Strategic modifications have enabled expansion of the processing volume of E-scrap. Enhancing recycling of wastes and scraps from urban mines while reducing the consumption of natural resources in the “O-SR” process will be demonstrated and discussed in the present paper. INTRODUCTION Onahama smelter and refinery has been operating as a custom smelter since 1965. Smelting facilities were subsequently expanded to two green-charged RF furnaces and five PS converters in 1973. Since RF is a conventional old-fashioned smelting furnace that necessarily consumes a huge amount of fuel to smelt copper concentrates, saving fuel cost has been an important objective. In early 1980’s the fuel was changed from bunker oil to pulverized coal, while utilizing the combustion heat of waste tires. Furthermore, treatment of combustible waste such as shredder residue (SR) was initiated in order to save fossil fuel for smelting concentrates in the RFs. Since enhancing of the treatment of SR requires a reduction in concentrate smelted in the RFs, most concentrates were dried and injected through tuyeres into the PS.converters. These modifications enabled to reduce the amount of the pulverized coal combustion and to increase SR treatment in the RFs. SR treatment capacity has increased to 12,000mt/month because the SR market has grown after the enforcement of the Vehicles Recycling Law. Such business environment has been attributed to establish the thermal-materials recycling system of SR in which the RFs have changed their role from copper concentrates smelting furnaces to waste materials combustion furnaces.

Jan 1, 2019

By Christopher Jon Preston, Troy Williams, Daniel Roy

There has been significant progress made with narrow vein gold mines in which a second option for crushing has begun to attract attention. To ensure the profitability of a mine that has based its economics on the absence of a crusher station, more than just best blasting practices are required. Using a blasting operation itself as a primary crusher would undoubtedly save enormous capital costs as well as eliminate some of the costs of crushing ore with the result that considerable savings might be realized. The challenge would be to define the conditions necessary to make this type of operation feasible by providing consistent blasting methods that result in a significant paradigm shift with respect to both blasting and current underground crushing methods. A break model has been developed and applied as a technique in designing blasting patterns based on a unit charge blasting geometry and stress reflection from free faces. There are four components to this model and these are 1) unit charge, 2) thermodynamic/energy, 3) stress reflection, and 4) radial break. Some important changes in timing between holes and rows based on rock properties and the percentage of burden moved were also used. On-site testing at a narrow vein gold mine in Quebec Canada, provided measured parameters for the model. No underground crusher was planned - relying only on the fragmentation profile generated by ring blasting. The specification for muck was that the fragmentation profile needed to be 100% < 400 mm (16 in) with no overbreak - with dilution less

Jan 1, 2019

By Avinash Kandalam, Markus Reuter, Jörg Kleeberg, Michael Stelter

The Top Submerged Lance (TSL) technology has obtained significant importance in the pyrometallurgy industry for nearly four decades. One of the advantages of TSL furnace is its high reaction rate, which is caused by splashing and turbulence of the melt. In contradiction, this phenomenon stands as a barrier for conducting experimental investigations to validate the simulation models. The highly turbulent and splashing environment in the TSL furnace is caused due to the immersion of the lance into the slag layer and thus the effect of the flame structure is directly related to the splashing, turbulence, reaction kinetics and life-span of the lance. Moreover, the material properties such as viscosity, density and the surface tension will also influence the flame structure. As a first step to understand the flame structure, attempts are made to generate a stable flame of the lance in an open environment. INTRODUCTION Top Submerged Lance (TSL) technology was invented during the 1970s at Commonwealth Scientific and Industrial Research Organisation (CSIRO), Australia by Floyd and Denholm. This technology was later commercialised and currently, there are about 100 TSL plants around the world commissioned by various licence holders such as AUSMELT (Outotec) and ISASMELT (Xstrata- Glencore Technology). Copper is the most produced non-ferrous metal followed by lead and zinc, see Hunt (2005). Today, a wide range of primary, secondary, and complex recycling materials are used as a feed material in the TSL, Alvear et al. (2010), Kaye et al. (2008). The working principle of TSL technology lies on inserting and submerging a lance from the top of a vertical cylindrical chamber into the slag layer. The lance is considered as the heart of the furnace, where the air and fuel are transported through two concentric tubes and are mixed in a combustion chamber, which is approximately 7 cm from the tip of the lance (considering the pilot-scale TSL furnace at the Institute for Nonferrous Metallurgy and Purest Materials - INEMET). The TSL furnace is very flexible with the type of fuel, feed material and the air input. The fuel can be natural gas/heating oil/fine coal particles and the air could be enriched with oxygen (Figure 1). The general mechanism of the TSL furnace lies on feeding the material from the top of the furnace and the material is pulled into the molten bath due to the high turbulent atmosphere, which results in high reaction rates. The thermocouples installed in the furnace (i.e. in the ceramic linings) allow the operator to know the temperature of the melt. For example, in the case of copper production the tapped material (i.e. matte/metal) can be transported to a settler for further processing or directly used.

Jan 1, 2019

By C. -G. Berg, J. T. Tuominen

Since the beginning of the 20th century, energy efficiency in copper smelting has been improved by a factor of 30 as a result of adopting autogenous smelting processes with more and more efficient waste heat recovery systems, increasing use of oxygen enrichment and countless smaller improvements. Nevertheless, energy in the form of electricity and fuels continues to be the biggest contributor to smelter operating cost. Metallurgists around the world are under constant pressure to find ways to save those precious megajoules wherever they can. One area that is often neglected is the removal of water contained in concentrates. Copper flotation concentrates, as delivered to a smelter, typically contain some 8–12% moisture. This moisture must be removed and the only way to do this is by evaporation, which consumes a lot of energy. Several studies have shown that the most efficient way of removing this moisture is to use a steam- heated indirect dryer—the least efficient way being the feeding of wet concentrate directly into a smelting furnace. Even in the most efficient smelters that employ modern steam drying, the energy needed to remove the moisture from the concentrates constitutes over 15% of the total energy consumption of a smelter – acid plant complex. The major steps that have been taken in the past to lower the energy consumption of moisture removal are the use of drying in general and the adoption of steam drying. The energy efficiency of concentrate drying has been improved by 25% over the last 20 years. The latest giant leap in this area, the Kumera Heat Recovery Dryer, is the result of Kumera’s long-term development in improving the efficiency of concentrate drying. The Heat Recovery Dryer is a novel application of steam drying that uses the waste heat from dryer exhaust gas for drying concentrates, thus, cutting the energy consumption by a further 30%. This paper discusses energy consumption in copper smelting in general and analyzes the energy consumption of concentrate drying in detail. Different dryer types are compared especially from the perspectives of energy consumption and environmental emissions. Applicability of different energy sources for drying is evaluated and discussed. The principle of the Kumera Heat Recovery Dryer is presented along with results from extensive continuous pilot plant tests. Potential applications and the feasibility of Kumera Heat Recovery Drying technology are discussed.

Jan 1, 2019

By G. Bonin, A. Jamal, G. Preciado, S. Gillis

"Accurate, easy to obtain, and reliable methods of measurement are the cornerstone of shaft and tunnel developments - during their sinking, operation and maintenance, or in some cases, remediation. This paper presents a new methodology to capture existing shaft conditions in such a manner that they can be transferred from the field to a digital copy, where they can be stored and used for engineering design purposes in a space not directly affected by the costs associated with schedule and equipment performance. The methodology utilizes basic principles of excavation alignment (plumb lines and survey instruments) while adding modern LiDAR, geolocation and survey control tools that can more completely capture the surrounding environment. The complete cycle of collection, processing, and delivery of pertinent information underground can take under an hour. During sinking, capturing data as a live stream measurement and being able to assess the alignment of the shaft liner can be critical to meeting rigid design tolerances. As sinking progresses, small changes in alignment or liner deviations can be captured and immediately corrected. Likewise, post-construction as-built conditions can be recorded and digitized, which will allow the mine personnel to compare the proper working condition to the actual condition years later. Observed changes can be identified and planned as future shaft repair works. This methodology has been developed and successfully deployed during the on-going sinking works of the two shafts at the Jansen Potash Project in south-central Saskatchewan and is described in greater detail in this paper.INTRODUCTION Light Detection and Ranging (or LiDAR) scans of the BHP Jansen Production and Service shafts during construction identified sections of both shafts where the internal radius of the temporary primary liner was insufficient to accommodate the tolerances of the permanent liner that was to be installed inside the temporary liner. These locations are referred to as “tights”. The “Tights Removal Program” was designed to collect high resolution point clouds of the shaft, using stringent survey control, that could be compared to the design profile to generate a heat map of locations for removal of up to 75 mm of steel-fiber-reinforced, 70 MPa concrete liner. This work was all on critical path, which made it valuable to save time on the schedule. Because concrete removal was a time-intensive task, it was essential to locate and remove only the concrete that would encroach on the planned permanent liner, while attempting to maximize the amount of cutting time. Removal was carried by a road header attached to a Brokk(R) 160, a small multi-attachment demolition machine."

Jan 1, 2019

By Micheal Mayhew

"This presentation will provide information and facts on the drilling and blasting within a frozen shaft using a full face methodology. The Author will briefly discuss the history of the sinking of a frozen shaft in Saskatchewan, the challenges faced, and the solutions delivered. The case study will include a discussion describing the series of events that led to the decision to adopt a full face blasting methodology. The case study will describe key elements such as the drilling pattern, hole size and depth, explosive products and blast vibration monitoring systems. INTRODUCTION During the shaft sinking process at a project in Saskatchewan, it was recommended that a drill & blast benching method be utilized. Following an evaluation of the site, the geological conditions proved amenable to a ground freezing system that would stabilize the rock formations and prevent inflows of water into the shaft (Table 1).The shaft sinking process required that the ground surrounding the proposed shaft be frozen by drilling several near vertical freeze holes radially at a specified distance from the edge of the proposed shaft excavation. This would allow for the circulation of a chilled brine solution down the freeze holes. The circulation is achieved by means of stainless steel pipes encased within each other to provide a delivery and return conduit for the brine (Figure 1). As a result of this periphery freezing, the ground within the shaft excavation is also predominately frozen.The finished internal diameter of the shaft was 5.5 meters with varying overall excavation diameters to facilitate different liner designs used for various rock formations. For the most part, the fully unsupported/unfinished excavated diameter of the shaft varied from 6.9 meters to 8.5 meters depending on the zone excavated. The challenge was that the proposed drill and blast excavation method posed a significant risk due to the potential to damage the freeze wall and pipes during blasting. The decision was made to commence the excavation through mechanical excavation (i.e. chip and cut) methods then change to a drill and blast method utilizing a split benching design. Through this process, the team encountered five main challenges: 1. Sub-horizontal geological structures and slips that affected blasting performance and sometimes resulted in a sloping surface to the top of the bench; 2. Confined working area for the crews and equipment due to a limited work area as a result of utilizing the split (half) bench drill and blast methodology; 3. Mechanical chipping and cutting of the one-meter buffer zone to the final shaft diameter; 4. Crews working on extremely slippery uneven frozen rock and ice surfaces, which affected safety and efficiency; 5. Establishing a blast vibration monitoring system to determine if the drilling and blasting of the full shaft excavation diameter were acceptable."

Jan 1, 2019

By S. Kemball-Cook, D. Heinze, A. Kornberg, M. Harmon

Climate change presents risks to mine infrastructure, operations and long-term obligations to protect environmental conditions. Management strategies and design of infrastructure and containment systems based on past or current climate conditions may be inadequate in the future if changes in climate are not taken into account in planning for mine operations, decommissioning, closure and post-closure. Data-driven assessments using climate model projections of the future can be used to quantify: • Changes in site-specific risks to mine structures, access, containment facilities, operations and staff safety. • Changes in vegetation and water balance/chemistry, and potential for acid mine drainage, erosion and design failure. Climate- and weather-related risks are a serious threat to the mining industry, but risk transfer solutions can alleviate these vulnerabilities. Mining companies can protect themselves through bespoke solutions which provide operators, investors and buyers with protection against weather-related disruptions to operations by hedging to smooth revenues. Using risk transfer structures to mitigate climate risks is a mechanism that is available to all types of mining operations world-wide. In this paper, we describe methods for evaluating site-specific climate change impacts and developing risk transfer solutions to mitigate their effects. EVALUATING MINE RISKS FROM CLIMATE CHANGE The best available tool for understanding potential future changes to the earth’s climate system are global climate models (GCMs) (IPCC, 2014). GCMs are computer simulations of the climate system which include the atmosphere, ocean, land surface, cryosphere and biosphere. Because of the computational demands of running a global model for many decades, the spatial resolutions of the GCM grids are necessarily coarse, typically on the order of 100-300 km. GCM data are therefore suitable for evaluating future physical risks on global or continental scales, but may not be appropriate for evaluating location-specific risks (e.g. Kotamarthi et al., 2016). For site-specific, quantitative physical risk assessment, GCM projection data are “downscaled” or adapted for use at the local level using statistical techniques together with observed data (statistical downscaling) or using high-resolution regional climate models (RCMs) that focus on a single geographic region and have spatial resolutions of 10-50 km (dynamical downscaling). Downscaling bridges the gap between the GCM scale and regional/local scale. Through the downscaling process, new information is added to the GCM output from observations and/or RCMs, resulting in patterns for weather variables that are more consistent with local terrain and weather influences. Downscaled climate change projections for the mine site are selected considering mine location and geography, the availability of local observations, and the performance of the downscaling method and global/regional models used to develop the projection in simulating the variable under study. Where possible, we use projections from an ensemble of global and regional model runs spanning a range of future greenhouse gas (GHG) scenarios.

Jan 1, 2019

By M. Girard, C. Farsangi, N. Singh

"Canadian Royalties Inc. owns and exploits the Nunavik Nickel Project: a copper and nickel deposit in Nunavik, Québec. The nickel and copper concentrates are filtered by plate and frame filter presses, and are transported 100km north to Deception Bay by truck. As the site is situated in the far north, extreme weather can be detrimental to production: roads can close for significant periods of time, resulting in the concentrator using all its storage capacity. During the winter of 2017, this accounted for over 100 hours of unplanned mill downtime. Different solutions to this problem were evaluated and the most economically viable combination of solutions was determined to be the use of concentrate storage containers and upgrading the plate size of the existing nickel filter press. By satisfying new, increased utility requirements, the cycle times would not change, but produce 30% more filter cake. Simulations were developed to determine the number of concentrate containers needed in conjunction with the upgraded press to eliminate unplanned downtime due to road closures and secure production through the winter. This paper summarises these simulations, the commissioning and start-up of the upgraded filter press, container loading procedures, and how this was put together to achieve a record 2018 winter season with a 90 percent reduction in downtime. The payback period of the project was 4 months. A specialised side-tipping trailer emptied the containers during the fall of 2018.INTRODUCTION The Nunavik Nickel Project is a nickel/copper mining project located in Nunavik, Québec. The nickel and copper concentrates are stored in stock tanks after thickening and are then filtered by plate and frame filter presses at the concentrator before being transported 100km to the shipping port at Deception Bay by trucks. The region is prone to periods of extreme weather during the winter, with winds that can reach +100km/hr and blizzards that severely limit visibility. The roads to Deception Bay are often affected by this weather, causing closures that last an average of 18hrs and as long as 72hrs. Additionally, there is a 15% chance that road closures occur within 24hrs of the last event. This has been an issue for the concentrator team since start-up in 2013, causing unplanned mill downtime every winter (Table 1) due to filling concentrate storage capacity during prolonged closures of the roads to Deception Bay."

Jan 1, 2019

By Erik Westman, Brandon Stables, Benjamin Mirabile

"Standing support is often used in conjunction with underground retreat mining. Knowledge of the load-displacement behavior of standing support and loading induced by the mine opening is critical to proper support selection. The NIOSH STOP database contains load-displacement laboratory test data for most commonly used standing supports. Hydraulic load cells currently used to measure in-situ loading of standing supports have exhibited leakage under load, producing irregularities within the dataset. An improved hydraulic load cell eliminates leakage and produces more consistent data.INTRODUCTIONA hydraulic load cell, more commonly known as a flat jack or JackPack, is a device installed to determine the loading characteristics of the roof-to-floor supports. These standing or roof-to-floor supports include, but are not limited to pumpable cribs, cans, wooden cribs (4-point, 9-point, etc.), metal props, wood timbers, concrete donut cribs, and other variations of these standing supports.Flat jack devices have been used previously to determine the loading of such roof to floor supports. The most commonly used load cell for standing supports is based on a design intended for pre-stressing standing supports, not load measurement. Preloading helps to keep the supports, such as timbers props and cribs, in place during the dynamic loading associated with blasting (Barczak and Tadolini, 2004).Flat Jacks are manufactured in various shapes and sizes depending on the application; common shapes are square and round that are 25.4 mm (1.0 inch) thick when collapsed, as shown in Figure 1. These load cells are produced in South Africa and can be formed into several different shapes depending on the application (Barczak, 2003). The sheet metal that makes up the bladder is comprised of 19-gauge or 1.11 mm (0.04 inch) thickness; the top and bottom pieces of sheet metal are resistance-seam welded around the perimeter. There are two different ports installed on one of the bladder skin corners of the flat jacks; these ports allow fluid to fill the unit, and the other port has a relief valve. The fill port is comprised of a check valve. The pressure relief valve is located in the second port; preset to 1,724 kPa (250 psi), the pressure relief valve keeps the load cell from bursting. Bursting of these load cells typically causes a small tear in the metal skin allowing the fluid to leak out without a large catastrophic failure.The effective inflation range of these load cells is between 25.4 mm (1.0 inch) to 254.0 mm (10.0 inches) thick. Different types of fluids can inflate these load cells but the most common and easily accessible fluid for testing applications is water. Water pressure from the mine supply line can inflate these load cells to the desired load. Depending on the pre-stressing requirements, a pneumatic powered pump, hydraulic pump, or hand pump may be required to inflate the load cells."

Jan 1, 2019

By H. G. Stephenson, D. Castendyk

Open pit anthracite mining at the Canmore Creek Mines, Canmore, Alberta, south of Banff National Park, resulted in several pit lakes by the early 1970’s. To enable future mining opportunities in the Rocky Mountains, operators decided to reclaim the site into a non-polluting landscape which would provide a memorable outdoor experience for residents and visitors alike, and would preserve wildlife habitat. Reclamation began with the stabilization and revegetation of spoil piles adjacent to Canmore Creek, and the backfilling and revegetation of Canmore Creek Mines No. 1 and 2 to create “Salamander Pond.” The company dammed the outlet of an open pit at Canmore Creek Mine No. 3 to raise the water level and create Quarry Lake. Reclamation concluded in 1980 when the Town of Canmore took ownership. Quarry Lake is now the centerpiece of 293-acre Quarry Lake Heritage Park, a popular destination for swimming, hiking, and fishing, visited by about 400 people on summer days. The Alberta Environment Conservation Authority described this as “The best mine reclamation in Western Canada.” Quarry Lake is an exceptional example of walk-away, pit lake closure, where the mining company created a valued post-mining asset and was released from future liabilities. INTRODUCTION One of the most important environmental issues associated with contemporary open pit mining is the closure of mine pit lakes, and the perpetual legacy these lakes can potentially generate. Ideally, successful pit lake closure includes the following: (i) the water quality within the pit lake, plus surface water and groundwater discharging from the pit lake, meets pre-mining, or other acceptable water quality conditions of the receiving environment, (ii) the termination of all active treatment processes, (iii) the return of the pit lake to the government for long-term care and maintenance, (iv) the release of the mining company from all future liabilities associated with the pit lake, (v) the return the environmental bond to the mining company, and (vi) the reuse of the pit lake for some post-closure, beneficial purpose. The achievement of these goals is known as “walk away, pit lake closure.” Peer-reviewed, publications of successful walk away, pit lake closure provide mining companies the ability to address public concerns regarding the safety of pit lakes which commonly occur during the permitting, operations, and closure phases of mining. To date, most published work on walk away, pit lake closure work has occurred in the coal mining sector in Germany and Australia (McCullough et al., 2009; Jones and McCullough, 2011; Kumar et al., 2013; Schultz et al., 2013). However, in North America, examples of walk away, pit lake closure are not widely discussed in the literature despite there being excellent examples from the coal mining sector in Alberta, Canada (e.g. Pleasure Island, Black Diamond, East Pit, Sphynx, Robb, Lovette, Siltstone, and Sterling), and from the iron mining sector in Minnesota in the United States (e.g. Portsmouth Lake, see MNDNR, 2018). Although seldom included in discussions of pit lakes from the metal and coal mining sectors, the aggregate and fabricated-stone mining sectors also produce pit lakes, and there are numerous examples throughout North America where these pit lakes have been successfully closed and transformed into post-mining resources. The difficulty of finding these good examples in the literature makes it challenging for companies to respond to public and regulatory questions regarding pit lake closure and reuse. As such, there is a pressing need document the motivations and approaches used in examples of successful, walk away, pit lake closure in North America so that the mining industry at large can learn from these examples and can better address public concerns.

Jan 1, 2019

During a period of six months in FY2018, a series of trials were conducted to compare drilling accuracy using two different methodologies and the subsequent impact this had on ore dilution. Testing was conducted at Cracow underground gold mine in Queensland, Australia. The drill rig’s existing alignment process was compared to a new technology system with the following observations: - Using the existing alignment process only 20% of holes surveyed recorded toe points within the +/-300mm (11.8in) tolerance blast-hole deviation. - The new technology was proven to limit rig alignment error, reducing average blast-hole deviation and increasing the number of holes drilled within tolerance by 160%. The increased accuracy reduced stope dilution by reducing over-break of subgrade ore: - Stopes drilled using the new technology recorded 62.6% less average dilution. - This contributed to an overall reduction in dilution for the full year (FY18) of 5 percentage points compared to FY17 - from 22% to 17% (a net decrease of 22.7%). A cost-benefit analysis extrapolated from the trials stipulates that if the new technology were in use for a full 12 months, when applied to FY17 full year data, a 10 percentage point reduction in dilution would represent a net 45.4% decrease, and would result in AUD8.2M (USD5.9) additional ore recovered, with AUD4.5M (USD3.2M) less spent on wasted cost of haulage and processing of diluted ore. As a result, return per tonne would increase 22%, from AUD87 (USD63) to AUD106 (USD77.1). INTRODUCTION Dilution – planned and unplanned – remains a significant cost impairment in the mining process. A series of trials were held over a six-month period in FY18 which established the cost-benefit of new technology as it applies to the alignment accuracy of production drilling rigs in underground mining, thus confirming its ability to limit drilling as one of the causes of dilution. The trials identified three underlying factors affecting drilling accuracy, measurable by blast-hole deviation surveys of planned vs actual toe data. These were; rig alignment error, collar location change/error, and in-hole deviation. The trials involved a comparison of existing rig setup processes and technology, with the new technology (Minnovare’s Production Optimiser system). The trials were undertaken in the same environment; an operating underground gold mine - Cracow Gold Mine. The comparison first revealed the extent to which rig alignment impacts blast-hole deviation. Secondly, the new technology was proven to limit rig alignment error, thereby reducing average blast-hole deviation and increasing the number of holes drilled within tolerance by 160%.

Jan 1, 2019

By G. E. Bogin, C. Strebinger, J. F. Brune

"Evidence shows that methane gas emanates from the mined-out area or gob of a longwall coal mine and can travel towards the working face, posing an explosion risk. Since the gob consists of varying levels of compacted rock, many researchers have modeled fluid flow through the gob as a Darcy-type porous media with a specified porosity and permeability. When studying methane gas explosions near the gob fringe, the Darcy flow assumption may not be applicable to describe the methane flame interaction with the gob. Computational fluid dynamic studies were performed modeling methane flame propagation across a simulated gob which was modeled as both a Darcy porous medium and as discrete rock objects with varying sphericity. Modeling the gob as a Darcy porous medium results in unrealistic methane flame propagation since the porous media assumption does not consider any differences in rock size and/or distribution. Additionally, the porous media model does not allow for ignition within and subsequent flame propagation through the porous medium, which must be modeled to understand the potential for methane gas explosions in the gob area. Modeling the gob as discrete rock objects produces more realistic methane flame dynamics and agrees with experimental observations. Modeling results show flame propagation across circles, hexagons, and squares, meant to represent rock rubble in the gob, produce different levels of turbulence which affects methane flame propagation velocity. This research demonstrates that modeling methane gas explosions in a longwall coal mine environment, specifically near the gob area, requires modeling obstacles, such as rock rubble, as discrete physical objects to capture the complex coupling of fluid dynamics, thermodynamics, and heat transfer. INTRODUCTION Although there are methods to mitigating methane accumulations in a longwall coal mine, explosive gas zones (EGZs) of methane and air may exist and pose an explosion risk to nearby miners and equipment (Brune, 2014) (Karacan, Ruiz, Cote, & Phipps, 2011). In the event of an explosion, the resulting methane flame and pressure wave can be catastrophic as evidenced by the Upper Big Branch explosion in 2010 that killed 29 miners (Page, et al., 2011). Since the mining process is transient, it is difficult to determine exactly where these EGZs exist, but investigative reports show in many cases, these EGZs can be near the working face, behind the shields, or within the gob area (Brune, 2014) (McKinney, et al., 2001). Additionally, miners have recounted seeing flames moving back and forth within the gob and under the roof supports (McKinney, et al., 2001) and in other cases, anecdotal evidence of hearing small pressure pops deep within the gob area (Brune, 2014)."

Jan 1, 2019

By D. Kulchyski, R. Thibault, D. Lamoureux

"Mine tunneling applications are sensitive to the leakage and friction performance of ducting systems. Improvements in performance can help project economics through reduction in drift height, booster fan spacing, fan electrical power requirement, and deferral of ventilation raise construction. Semirigid plastic ducting has enjoyed significant adoption in mine tunneling in recent years. This paper explores technical properties and performance aspects of this relatively new material application.INTRODUCTIONUnderground mining projects are sensitive to mine development cost and schedule to meet first production—both of which are defined to a substantial extent by mine access construction. The very nature of mine access development requires driving accesses into new areas and even mechanized and automated tunneling methods require ventilation. Until underground airways are connected, allowing a flow-through circuit, ducted ventilation is required to establish ventilation within any single-access (i.e.: dead-end) heading. See Figure 1 as an example of ducted ventilation. Improving performance of ducted ventilation systems impacts project cost and schedule in several ways:For drifts whose height is defined by overhead clearance above haul trucks or tall equipment, smaller diameter ducting will decrease heading size.With higher ventilation flows, activities can be less ventilation-constricted; secondary headings can be worked without restriction, which improves schedule.Given the ability to provide more air for a given fan power, blasting gasses can clear the face and mine more quickly so crews can return to work more quickly - allowing higher advance rates.Lower electrical costs – both due to lower power consumed by fans and with the requirement for fewer electrical stations to power booster fans."

Jan 1, 2019

By G. J. Heferen, A. Pranowo, N. J. Aslin, P. O. Eriksson

Glencore Technology (GT) has over four decades experience supplying stainless steel cathode plates (“cathode plates”) to the electro-refining and electro-winning industry. Cathode plates are typically the single biggest capital investment in a refinery. Refineries may view cathode plates as fixed asset or consumables depending on their operational characteristics. This paper examines the issue of cathode plate life and the strategies and philosophies used by different plants in the management of their cathode plate asset. Some plants operate with their original plates after more than 20 years. Others accept high turnover and regular maintenance as normal operating practice. Reference data are provided on plate life for various operating plants including benchmark plants achieving best-practice plate life and operating cost. The role of the electrode handling equipment on cathode plate longevity is also examined, including latest developments in Cathode Stripping Machine, robotic copper stripping, and full-automation production cranes. The ability to identify and manage the population of plates in service is also critical for maximising plate life and minimising its overall operating cost. This paper discusses a novel and unique RFID system for tracking and managing cathode plate inventory. INTRODUCTION Permanent cathode plates The adoption of permanent stainless steel cathode electrodes in the electro-refining of copper was the most significant process development since the first commercial electro-refineries were built in the late 19th century. It provided significant improvement over the labour intensive and complicated starter sheet system. Copper grows over the permanent cathode blade for a number of days before being stripped, and the permanent cathode can be returned straight back to cells for the next cathode cycle. Glencore Technology (formerly Mount Isa Mines (MIM), then Xstrata Technology) has been manufacturing permanent stainless steel cathode plates from the late 1970s with the birth of ISA PROCESS™, and the Kidd process that came one decade later. Invented and commercialised by Mount Isa Mines, the ISA PROCESS™ was first implemented into Copper Refineries Limited (CRL), Townsville, in 1978. The KIDD PROCESS by Falconbridge evolved in the 1980s and was first implemented into the Kidd Creek Tankhouse, both operations converting from traditional copper starter sheets.

Jan 1, 2019

By M. A. Reyes, J. Bickson, J. R. Srednicki

Federal laws mandate the presence of refuge alternatives (RAs) in underground coal mines and provide guidelines for harmful gas removal. After an explosion, harmful gases can follow survivors into an RA and can reach a deadly concentration. Investigators from the National Institute for Occupational Safety and Health (NIOSH) tested 12 ventilation system configurations (VSCs) to purge sulfur hexafluoride (SF6) tracer gas from a built-in-place (BIP) RA in the Experimental Mine in Bruceton, PA. Using a borehole air supply, tests were conducted with airflows of 750 and 1,000 standard cubic feet per minute (SCFM). Excluding a VSC where the air inlet was 1.98 m (78 in) from the air outlet, the results show that the time to purge the SF6 concentration from 1,000 parts per million (ppm) to 25 ppm ranged from 26 to 29 minutes for an airflow of 750 SCFM and ranged from 18 to 23 minutes for an airflow 1,000 SCFM. Mines can use this information to reduce purge time in case of a mine disaster and determine which VSC to avoid. INTRODUCTION After a fire or an explosion in an underground mine, the concentration of carbon monoxide can reach a fatal level. In a mine disaster, the main goal is to escape. However, if miners cannot escape, they have to migrate to a location to find refuge and, if possible, communication, and a borehole source for a fresh air supply. To ensure survival of the miners, Federal laws mandate the presence of a refuge alternative (RA) within 304.5 m (1,000 ft) of the nearest mining face. In addition, Code of Federal Regulations Title 30 CFR Section 7 sets the guidelines for personnel tracking, RAs, and the removal of noxious gases in underground coal mines (Mineral Resources, 30 CFR, 2014). Federal regulations define an RA as a protected, secure space with an isolated atmosphere and integrated components (Mineral Resources, 30 CFR, 2014). There are three types of RAs: portable metal RAs, portable tent-type RAs, and built-in-place (BIP) RAs. A BIP RA is constructed using masonry or other stoppings to create an isolated space in a mined-out area. Blast doors are installed in one or both of the stoppings for the miners to enter the RA. Furthermore, RAs must provide the following components: breathable air, food, water, air monitoring, and harmful gas removal. Federal regulations have emphasized the mandate for breathable air and harmful gas removal in the following words: “Purging or other effective procedures shall be provided for the airlock to dilute the carbon monoxide concentration to 25 ppm” (Mineral Resources, 30 CFR, 2014). The purpose of the mine ventilation system is to provide a sufficient quantity of air to the underground mine workings, to dilute methane and other contaminants, to maintain a suitable working environment, and to prevent accidents from happening (Cheng and Wei, 2014). In addition, the organic nature of coal amplifies risks from poisonous gases, explosions, and fires (Engström et al., 2018). If an underground coal mine ventilation system fails after an explosion, the concentration of toxic gases, most notably carbon monoxide, will increase. Carbon monoxide is dangerous because it creates tissue hypoxia by binding to hemoglobin (Özmen and Aksoy, 2015).

Jan 1, 2019

By S. Nikolic, G. M. Stieper, D. P. Mallah, B. J. Hogg, P. B. Voigt

Copper feed materials processing is becoming more challenging, due to an incremental increase in the mineralogical and compositional complexity of these feeds. These complex and polymetallic feeds are now becoming more common and many sites have been forced to re-evaluate their operating strategies to process these materials at cost competitive rates, whilst meeting ever more stringent environmental regulations. Most operations must first evaluate the merits of pyrometallurgical and hydrometallurgical treatment routes. Although there are multiple copper smelting technologies available, only top-submerged lance (TSL) technology, supplied by Glencore Technology as ISASMELT™, has been applied in the real world to consistently and successfully smelt complex materials in integrated metallurgical facilities such as Glencore’s Kazzinc Ltd. operation in Kazakhstan, Umicore Precious Metals Refining in Belgium and Aurubis AG in Germany. Glencore Technology also offers hydrometallurgical processing, through the Albion Process™ technology, opening up viable flowsheet options previously not possible for these complex feeds. This paper describes a number of real world process flowsheets at global operations and Glencore’s own operations at Mount Isa and Kazzinc Ltd., which process complex feeds. These flowsheets integrate the ISASMELT™, Albion Process™, ISACONVERT™, ISAKIDD™ Tank house, and bottom blown oxygen cupel (BBOC™) technologies to provide an effective process solution for the treatment of complex polymetallic feeds to produce metallic copper and associated by-products. INTRODUCTION Traditional smelters and those built in recent times within the bulk smelting hubs of the world have been designed to treat standard/clean concentrates. In recent years the processing of complex polymetallic sulfide concentrates and the recycling of secondary copper and derivatives of waste electrical and electronic equipment, such as e-scrap, have become a focus for numerous companies (Alvear & Nikolic, 2013). Processing of these complex feeds, characterized by relatively high levels of minor elements (over 5% of elements such as arsenic, antimony, bismuth, lead and zinc) is more challenging. Facilities not designed for these types of materials may require significant modifications or a change in smelting technology to treat them. Often operations find themselves re-evaluating the merits of pyrometallurgical and hydrometallurgical treatment routes for their sites through a number of factors:

Jan 1, 2019

By R. Hildebrandt, K. Cybulski, G. V. Goodman, Z. Dyduch, M. L. Harris, M. J. Sapko

Past research showed that bituminous coal dust remains dry and dispersible in the presence of moisture. Rock dust must disperse with the coal dust to effectively inert a propagating coal dust explosion. Non-treated rock dust readily absorbs moisture, limiting its dispersibility, while anti-caking treated rock dusts can remain dry. The National Institute for Occupational Safety and Health contracted the Central Mining Institute in Poland to conduct large-scale testing in their Experimental Mine Barbara to determine if a treated rock dust can be as effective as non-treated rock dust in attenuating or quenching coal dust explosions under the same experimental conditions. INTRODUCTION One of the goals of the National Institute for Occupational Safety and Health (NIOSH) is to conduct research to reduce the risk of mine disasters and provide workplace solutions to reduce the risks associated with accumulations of combustible and explosible materials; the most common form of which is the generation of coal dust during the mining process and its subsequent distribution downwind. Dispersible rock dust is a primary defense for preventing coal dust explosion propagation in underground coal mines, and its properties are defined in 30 CFR 75.2. “Pulverized limestone, dolomite, gypsum, anhydrite, shale, adobe, or other inert material, preferably light colored, 100 percent of which will pass through a sieve having 20 meshes per linear inch and 70 percent or more of which will pass through a sieve having 200 meshes per linear inch; the particles of which when wetted and dried will not cohere to form a cake which will not be dispersed into separate particles by a light blast of air; and which does not contain more than 5 percent combustible matter or more than a total of 4 percent free and combined silica (SiO2), or, where the Secretary finds that such silica concentrations are not available, which does not contain more than 5 percent of free and combined silica.” An earlier NIOSH investigation of rock dust revealed two significant concerns with the supply of rock dust to U.S. coal mines: 1) insufficient particles <200 mesh (75 μm) and 2) all rock dusts when wetted and dried formed cakes and were not easily dispersed with a light blast of air (1). Past research by the U.S. Bureau of Mines and others showed that bituminous coal dust remains dry and dispersible in the presence of moisture (2). Rock dust must also be dispersible in concert with the coal dust to effectively inert a propagating coal dust explosion (3, 4, 5, 6). Non-treated rock dust, however, readily absorbs moisture, limiting its dispersibility, while a rock dust treated with long-chain fatty acids (such as stearic acid) can remain dry and dispersible. Stearin-treated rock dust has been used in British coal mines (7) and is commonly used in Polish coal mines.

Jan 1, 2019

By I. Mc Dougall, H. Joubert, G. de Villiers

The use of sidewall copper cooling systems to prolong furnace campaign life is becoming an accepted technology solution in the base metals industry. Tenova Pyromet has designed and installed a number of sidewall copper cooling systems in base metals furnaces, including the platinum industry. Apart from increasing the furnace campaign life through the formation of a stable freeze lining, a well-designed copper cooling system enables the plant operator to focus more on optimizing the process to achieve throughput and recovery targets, and to accommodate more varied and available concentrate feed blends. The paper discusses the design of sidewall copper cooling systems for copper smelting and converting furnaces to achieve the above objectives. More specifically, the design of copper cooling systems for top submerged lance furnaces are discussed. An overall increase in furnace heat losses has been raised as a concern for intensively cooled sidewalls. The paper explores the overall heat loss expectations for copper cooled furnaces versus traditional refractory lined furnaces. In addition, the potential use of alternative cooling media is discussed. INTRODUCTION Base metal smelting and converting furnace technologies have been evolving continuously over the past century to satisfy the need for higher throughput, improved efficiency, and longer campaign life. To accommodate these demands, in particular higher smelting intensity and throughput, furnace bath containment systems had to improve. The use of pure refractory lining systems has slowly made room for the use of more intensively cooled lining systems (Joubert, Nikolic, Bakker & Mc Dougall, 2016). These cooling systems evolved from external shell cooling, such as shower or film cooling, to copper plate coolers extending into the furnace refractory lining, and high intensity stave or panel coolers (Verscheure, Kyllo, Filzwieser, Blanpain & Wollants, 2006). Consequently, an increasing number of base metal smelting and converting furnaces are equipped with copper cooling systems, including flash furnaces (Bryk, Ryselin, Honkasalo, & Malmstrom, 1958; Yasuda, Motomura & Kawasaki, 2014; Marx, Shapiro & Henning, 2010), top submerged lance primary smelting and fuming furnaces (Bhappu, Larson & Tunis, 1994; Kim, Lee & Lee, 2000; MacRae & Steinborn, 2018), top submerged lance converting furnaces (Viviers & Hines, 2005; Nikolic, Hogg & Voigt, 2018), primary platinum smelting electric furnaces (Nelson, Stober, Ndlovu, De Villiers & Wanblad, 2005; Jones, 2005; Hundermark, De Villiers & Ndlovu, 2006; Mc Dougall, 2013), and electric slag cleaning furnaces (Joubert, Nourse, Masters & Hundermark, 2005).

Jan 1, 2019

By A. Romero, M. Carvalho, D. L. Millar

"The number of underground mines replacing diesel by battery powered mobile equipment is growing worldwide. The latter produces locally zero emissions and less heat, improving air quality in the working areas, and can potentially reduce energy costs due to lower ventilation requirements and in the face of higher fuel prices. However, there is a lack of systematic approaches to evaluate the potential economic benefit of switching from diesel mobile technologies to electric ones. This paper presents a method to answer the question of whether a mine with known operating conditions should invest in battery-powered electric equipment to reduce its total costs. Furthermore, this method provides the optimal number of electric and diesel equipment in relationship with their impact on the ventilation system and the total costs of running the mine from the energy perspective. A case study of an underground mine in Northern Ontario (Canada) is presented to validate the method proposed. The scenarios studied include the specific climatic conditions of the region, and the possibility to use heat recovery for the ventilation system. Overall, results show that the use of electric mobile plants is cost competitive, especially so when electricity cost can be lowered through load-shedding strategies.INTRODUCTIONOf the multiple advantages of using electrical vehicles (EV) underground in mining, the potential increase in air quality and comfort is the most significant (Paraszczak, Svedlund, Fytas, and Laflamme, 2014). Until recently, fully battery-powered electrical underground heavy duty machinery (i.e., loaders or trucks) were not available, so that tethered and trolley assisted vehicles were the only electric alternatives to diesel powered vehicles (Bétournay et al., 2011). Today, several commercial battery-based alternatives are available (General Electric Fairchild, 2015; RDH Mining Equipment, 2015; Paraszczak et al., 2014). Operational details can be found in Ewing (2015). The main battery technology used (Lithium Iron Phosphate, LiFePO4, or LFP) was already anticipated in Bétournay et al. (2011) as a good candidate for these types of vehicles. More details on these batteries, along with state of the art and future perspectives can be found in Zubi, Dufo-López, Carvalho, and Pasaoglu, (2018)."

Jan 1, 2019