Search Documents

By J Herrmann, J Richards, B Hutchison

An extensive trial of laser-based survey and monitoring systems at Hillgrove Resources Kanmantoo Copper Mine in the Adelaide Hills, South Australia, has proved the capabilities of the system in monitoring rock movements on open pit walls. Initially, the trial involved deploying a Maptek I-Site 8820 laser scanner and the proof-of-concept Maptek Sentry software in the Nugent Pit to monitor ductile rock movements located up to 260 m away. The system was proven to be capable of monitoring various rock movements from 1.5 tonne rockfalls up to a 40 m high toppling wall failure. Data collected from smaller rockfalls was used to help build a database for Hillgrove’s rockfall management program. As part of the trial, the laser scanner was deployed to monitor a ramp movement event, as well as the toppling failure, adjacent to an IBIS slope stability radar. Both devices monitored the slump and the slowly developing toppling movements, with similar results. Although the radar was used as the successful ‘critical alarm’ device for the toppling failure, post-failure analysis showed the laser-based system to be capable of performing a similar role in the ductile rock regime; albeit over much shorter distances than the radar capability. A second laser scanner was deployed to monitor Kanmantoo’s Emily Pit in early December 2014, where it successfully provided critical alarm warnings for a block topple event. Sentry software, which takes advantage of Maptek I-Site 3D spatial imaging technology, was first released in November 2014 to meet industry demand for a cost effective, flexible system to detect movement. Sentry has now been re-launched as a fully transportable monitoring system. Deployed in a custom trailer, the system offers a power and communications module, cellular and Wi-Fi networking and a stable bollard for the I-Site laser scanner and Sentry software. This paper will present rock wall movement data from the Sentry trial and a subsequent two years of monitoring of the open pit walls at the Kanmantoo Copper Mine, at distances out to 750m. In addition, examples of remote geological mapping and small rockfall detection, using the laser scans, will be described. The Sentry system has proven to be beneficial for the continual improvement of slope monitoring and risk management at hard rock mines. CITATION:Hutchison, B, Richards, J, Richards, J and Herrmann, J, 2018. Mine rockfall and rock wall failures – proven digital laser-based approach for monitoring slopes at the Kanmantoo Copper Mine, in Proceedings The Fourth Australasian Ground Control in Mining Conference (AusRock), pp 463–472 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 30, 2018

By J Kwiri, T Zvarivadza, R Mitra, F Cawood

It is crucial to record ground movement of any magnitude to enable the safe and economical design of excavations and infrastructure. The DigiMine Laboratory is equipped with technologies to record such movements. This paper analyses the effectiveness of the Digital Mine instrumentation in recording earth movements in light of the Botswanan earthquake which occurred on the 3rd of April 2017 at 17:40 UTC. Recordings from the Digital Mine are compared with other ground sensing technologies which also captured the event (USGS and GEOFON systems). USGS and GEOFON system’s recordings suggest that, there are a number of possible mechanisms that could have resulted in the earthquake as discussed in the paper. Compared to the USGS and GEOFON systems, DigiMine system could not provide an analysis that could give possible source mechanisms. However, the system’s success in recording the Botswanan earthquake, is an indication that the system works and can be further developed or improved. For a comprehensive analysis, more data from various sensors needs to be collected. For example, DigiMine connecting to the national seismic monitoring system or to the local mine’s seismic monitoring system. Such connections will enable the development of a better self-analysis system and possibly prediction of future events. More importantly, it will contribute to better understanding of regional seismicity and its potential impact on excavation design. CITATION:Kwiri, J, Zvarivadza, T, Cawood, F and Mitra, R, 2018. How efficient is DigiMine technology in recording earth movements? A look at the Botswanan earthquake, in Proceedings The Fourth Australasian Ground Control in Mining Conference (AusRock), pp 414–419 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 30, 2018

By J Franz, S Bock, N Hentrich

Artificial ground freezing is the unrivalled method for groundwater control during mine shaft sinking. Moreover, ground freezing may also provide temporary ground support. The fast development of fibre-optic temperature monitoring devices, three-dimensional freeze pipe survey methods and numerical modelling software provide grounds for developing new and reliable tools for ground control during freeze shaft sinking. This paper presents examples of predictive numerical models that are based on back-analysis and calibration of temperature data that covers the complete construction cycle from pre-freezing through to artificial thawing. The back-analyses showed that standard numerical models are not capable of predicting the prevailing thermo-mechanical conditions satisfactorily. This paper describes the development and implementation of new tools for improved consideration of concrete hydration and latent heat, along with the introduction of other algorithms that improve and simplify the efforts of managing complex numerical models. A function is presented that allows for an automated correction of the model’s mesh based on results of three-dimensional freeze pipe surveys. This paper demonstrates that the latter consideration is important, because the often employed assumption of idealised freeze circle geometry in numerical models impacts on the accuracy of such model’s predictions. Subsequently, the verification of these extended numerical models is demonstrated. Due to its flexibility, the FLAC3DTM code was employed for the numerical modelling. This software provides the possibility of implementing additional functions written in internal FISH or Python language into the models. It is concluded that state-of-the-art techniques for freeze hole drilling and surveying, on-site monitoring and advanced numerical analysis provide a significant potential for both the design and the operation of largescale ground freezing measures. The application of the extended numerical models for predictive simulations during construction allows for temporary shaft lining optimisation, for assisting in operational decision making and for compensating temporary loss of monitoring data. Suggestions are made for required future work in order to further improve the developed ground control tools. CITATION:Bock, S, Franz, J and Hentrich, N, 2018. New tools for ground control in freeze shaft sinking, in Proceedings The Fourth Australasian Ground Control in Mining Conference (AusRock), pp 393–406 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 30, 2018

By Y Li, B Shen, S Zhang

Jointed rock mass is often encountered in rock engineering and its stability has always been a major concern in underground engineering. To analyze the stress characteristics and their variations in jointed rocks, in this study, a new concept of sub-instability stage before rock failure is defined, and a new experimental method is used to investigate interaction between defects and intact rock of the jointed rock mass during the subinstability stage., Firstly, external characteristics of stress and failure mode of the whole jointed rock are investigated systematically by conducting uniaxial compression tests on red sandstone samples with a set of preexisting open flaws of different sizes, and the interactive damage of intact parts and defects in the subinstability stage was further studied. Secondly, rock-like material samples made of bonded plaster blocks were tested and internal data from stress sensor between the strong and weak segments were collected. The transforming processes from independent activity of the individual segment to overall interactive movement of jointed rock before the unstable failure were analysed. The test results indicated that the subinstability stage marked the beginning of interactive failure between the intact rock and defects. In the early subinstability stage, the relatively intact parts bore most of the load in a jointed rock mass, and the defects were damaged firstly which caused high strain around it. The areas of high strain increase rapidly, extending and migrating, causing damage to the intact parts. In the later sub-instability stage, the interaction effect reached its maximum, and a large number of cracks appeared in the intact rock and they propagated and coalesced. Intact parts experienced rapid failure and then the jointed rock failed. The experimental method used in this paper to identify the sub-instability stage could be used to identify failure precursors of jointed rock masses and to develop technology for disaster prevention in rock engineering. CITATION:Zhang, S, Shen, B and Li, Y, 2018. Experimental studies on interactive failure characteristics of jointed rock, in Proceedings The Fourth Australasian Ground Control in Mining Conference (AusRock), pp 453–461 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 30, 2018

By E Kabwe, E Chanda, M Karakus, S Akdag

The Convergence Confinement Method (CCM) is one of the frequently used methods that considers the ground response to the advancing tunnel face. The CCM analytical solutions represent stress relaxation on circular tunnel walls in a rock/soil media. The CCM analytical solutions is based on circular tunnel geometry and consider a hydrostatic stress field in a homogeneous isotropic rock mass condition. However, noncircular tunnel geometries, non-hydrostatic stress field, staged excavation process in a discontinuous anisotropic non-linear rock mass conditions are usually ignored in these analytical solutions. In this paper, we investigate the performance of the existing CCM analytical solutions developed for elastic and elastoplastic ground behaviour for circular tunnels. For this purpose, a finite difference analysis is conducted to compare the analytical results with the results obtained from Finite Difference Method (FDM) for a chosen rock mass condition. Results obtained from the investigation shows that floor, crown and wall displacement are 30%, 10% and 23% more, respectively, in a horse-shoe relative to a circular tunnel. This indicates that the application of analytical formulation tailored for circular tunnels would lead to inaccurate quantification of wall convergence in horseshoe-shaped tunnels. CITATION:Kabwe, E, Karakus, M, Chanda, E and Akdag, S, 2018. Investigating the tunnel closure using convergence confinement method and 2D plane strain finite difference analysis, in Proceedings The Fourth Australasian Ground Control in Mining Conference (AusRock), pp 152–159 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 30, 2018

By B Banerjee, H Masoumi, X Shen, S Raval, D Tannant

Structural mapping of pit walls can be performed using digital images and photogrammetry software, but the performance is limited by weather and environmental conditions including dust, rain and light. On the other hand, active sensors such as terrestrial laser scanners (TLS) and total stations (TS) suffer from vertical orientation bias and occlusions when persistent discontinuities dip at the same angle as the scanner line-ofsight. The recent development of the compact light detection and ranging (LiDAR) systems has made it possible to mount these sensors on unmanned aerial vehicles (UAVs) or drones which offer the potential to overcome limitations that are inherent in existing mapping systems. This study details the research involving integration and application of an advanced UAV-LiDAR system for structural mapping of a highwall. A state-of-the art laser scanner with an inertial measurement unit (IMU) and real-time kinematic global positioning system (GPS) was integrated on to a UAV. The system was first tested in a laboratory condition. Then the UAV-LiDAR system was employed to map a highwall of a coal mine. The planned flight trajectories tested the system at variable distances from the highwall face and at various speeds. The raw data collected from individual sensors were fused, filtered to remove noise, and segmented to produce a surface scan model. Finally, the point density and surface coverage were measured using the surface scan model of the highwall. The parameters were compared with equivalent measurements computed from a reference TLS data. The study demonstrates the capabilities of a UAV-LiDAR system to generate accurate and occlusion free data for mapping highwall geological structure with very quick and efficient flights in the field. CITATION:Raval, S, Banerjee, B, Shen, X, Masoumi, H and Tannant, D, 2018. Evaluation of a UAV-LiDAR system for mapping geological structures in an open pit highwall, in Proceedings The Fourth Australasian Ground Control in Mining Conference (AusRock), pp 496–503 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 30, 2018

By T Stambolie

Mine planning processes are continuously evolving, increasing in complexity, and are required to be developed in shorter timeframes, often missing important steps in the process. Underground coal mines are also moving into more challenging environments, with the more favourable resources having been exhausted. In addition to traditional mine planning processes there is an increasing level of complexities associated with parallel systems including the preparation of Joint Ore Reserves Committee (JORC) compliant estimates (JORC, 2012 and Guidelines Review Committee, 2014) or seeking critical regulatory development consent to undertake mining. There is a clear link between geotechnical considerations and success of mining operations, and therefore it is essential that such considerations are elevated in both status and priority. It is obvious that geotechnical considerations are paramount in any mine, however it is imperative to accept that such considerations, and the collection of information relating to such, are undertaken from the onset of any mining project. CITATION:Stambolie, T, 2018. Elevating geotechnical considerations in the Australian underground coal industry and mine planning process, in Proceedings The Fourth Australasian Ground Control in Mining Conference (AusRock), pp 383–391 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 30, 2018

By P Wilson

The Mt. Wright Underground Mine is located near the town of Ravenswood in North Queensland and is operated by Carpentaria Gold – a wholly owned subsidiary of Resolute Mining Limited. The establishment of the world’s first Sub Level Shrinkage (SLS) mine from a tradition Sub Level Open Stoping operation has proven to be a geotechnical challenge which has required tailored solutions to overcome unique issues. This paper will be broken into two distinct sections that will outline: a brief overview of the mining method and how the SLS method was chosen; and how the SLS is managed and key geotechnical learnings. The story of the world’s first SLS originated from the need of a bulk mining method to ensure the viability of Mt. Wright into the future. Traditional bulk mining methods such as; Block or Sublevel Caving were originally ruled out due to the low natural ‘cavability’ of the orebody and the proximity of the orebody to existing major infrastructure (Decline, Ventilation Rises and Egresses). The first section of the paper will outline the key geotechnical information that helped decide the SLS method in addition to how continuous backfill influenced the design. The second section is intended to address issues that the geotechnical engineers encountered since the inception of the SLS. The feature topic of this section is mining induced stress. Like most bulk mining methods, Mt. Wright had success when the production front was running parallel to the stress (production front being ‘shadowed’ from the stress). This was until a design change, forced by a splitting ore body resulted in this shadowing effect becoming harder to achieve. As a result, rehabilitation and production hole re-drilling become a regular occurrence, which teamed with a strict set of access controls made the production cycle longer and harder to complete. CITATION:Wilson, P, 2018. Mt Wright – geotechnical learnings from a sub level shrink, in Proceedings The Fourth Australasian Ground Control in Mining Conference (AusRock), pp 119–132 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 30, 2018

By H Esterhuizen

The Ernest Henry Mine (EHM) in Queensland, Australia is a Sub-level Caving operation that started production below the previously mined open pit at a depth of 535m. Current Production mining has progressed to a depth of 730m, with planned production mining to extend down to at least 1000m below surface. The inclined nature and geometry of the orebody combined with geological structures provides for challenging mining conditions. Over several years, Ernest Henry Mine has introduced measures to improve outcomes based on observations, monitoring and data analysis. As mining progresses deeper, EHM will continue to proactively take steps to ensure future outcomes are anticipated and mining can continue safely and uninterrupted. The focus of this paper is on the changes in seismic- and stress-driven behaviour of the rockmass experienced at EHM, the ground control measures implemented, and the anticipated future conditions and controls required. CITATION:Esterhuizen, H, 2018. The evolution of seismicity and ground control measures at Ernest Henry Mine, in Proceedings The Fourth Australasian Ground Control in Mining Conference (AusRock), pp 20–41 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 30, 2018

By I Canbulat, J Oh, A Mcquillan, D Payne

This paper presents a new risk assessment tool for coal mine excavated slopes. This new empirical-statistical Slope Stability Assessment Methodology (SSAM) is intended for use by geotechnical engineers at both the design review and operational stages of a mine’s life to categorise the risk of an excavated coal mine slope. A likelihood of failure is determined using a new slope stability classification system for excavated coal mine slopes developed using a database of 119 intact and failed case studies sourced from open cut coal mines in Australia. Consequence of failure is based on slope height and stand-off distance at the toe of the excavated slope. Results are presented in a new risk matrix, with slope risk being divided into low, medium and high categories. The SSAM is put forward as a new risk assessment tool to assess the potential for, and consequence of, excavated coal mine slope failure. Unlike existing classification systems, assumptions about the likely failure mode or mechanism are not required. Instead, the SSAM applies an approach which compares the conditions present within the excavated slope face, with the known past performance of slopes with similar geotechnical and geometrical conditions, to estimate the slope’s propensity for failure. The SSAM is novel in that it considers the depositional history of strata in an excavated slope and how this sequence affects slope stability. It is further novel in that it does not require explicit measurements of intact rock, rock mass and/or defect strength to rapidly calculate a slope’s likelihood of failure and overall risk. Ratings can be determined entirely from visual observations of the excavated slope face. The new SSAM is designed to be used in conjunction with existing slope stability assessment tools. CITATION:Mcquillan, A, Canbulat, I, Payne, D and Oh, J, 2018. New risk assessment method for coal mine excavated slopes, in Proceedings The Fourth Australasian Ground Control in Mining Conference (AusRock), pp 473–495 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 30, 2018

By T R. Stacey

South Africa has a long history of rockbursts, some 100 years. During this time much research and many developments have taken place in the country to limit the occurrence of rockbursts, and to mitigate their effects. In this paper I shall present a personal view of what I consider to be important achievements, and contributions made. Some of these are: planning of stope layouts, and the use of strike barrier pillars; recognition of energy as a key factor, the use of the energy release rate ERR as a layout planning criterion, and development of MINSIM for calculation of ERR and stope planning; sequential grid stope layouts; use of backfill for stope support; and, development yielding support elements, and dynamic testing of stope and tunnel supports. The record shows the establishment of a rock engineering research powerhouse over a 40 to 50 year period and, unfortunately, the complete breakdown of this capability in the subsequent 10 years. CITATION:Stacey, T R, 2018. A personal review of South African rockburst research, experience and lessons learnt, in Proceedings The Fourth Australasian Ground Control in Mining Conference (AusRock), pp 5–16 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 30, 2018

By P Hagan, S Wang, D Li, B Loh

A study was undertaken to quantify the differences in performance between a full-length encapsulated cable bolt and a partially encapsulated cable bolt. Much research has been reported on the differences in cable bolt design and operational parameters such as borehole diameter and grout type with much of this based on the Laboratory Short Encapsulation Pull Test (LSEPT). However, there is a gap in knowledge surrounding the effect of anchorage length on load transfer and cable bolt performance particularly with respect to the role of the bulb in modified cable bolt designs. The objective of this study was to expand the existing knowledge base of cable bolt performance with the intent of developing a revised design criterion. Alongside a comprehensive review of current cable support theory, design and practice, a series of pull tests was undertaken to compare each anchorage method using a high capacity modified cable bolt. The results serve to confirm earlier work on fully encapsulated anchorage. Both the peak load capacity and stiffness of the fully encapsulated cable bolt were nearly double that of the partially anchored cable bolt. When the tests were repeated in an oversized borehole, while there tended to be more variation in performance, there was little significant difference in the mean results. In addition to anchorage length, there are other factors that contribute to cable bolt performance including in order of sensitivity: embedment length, water-to-cement ratio of the grout, type of grout and borehole diameter. CITATION:Loh, B, Hagan, P, Li, D and Wang, S, 2018. A comparison of the performance of fully versus partially encapsulated cable bolts based on laboratory-scale testing, in Proceedings The Fourth Australasian Ground Control in Mining Conference (AusRock), pp 291–302 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 30, 2018

By D Adhikary, M Khanal, B Poulsen, H Guo

During longwall mining, the ability to reliably estimate the height of longwall mining-induced fractures is critically important in order to effectively manage mining-induced water inflows and aquifer interference. The extent of mining-induced subsurface deformation, fracture, surface subsidence and aquifer interference is largely controlled by local lithological conditions, mining methods and mine layouts. Therefore for the purpose of quantifying mining impacts it is imperative to incorporate the local geology and mine plan parameters in a mine scale model. Two different numerical models based on 3D continuum (Finite Element Method) and 2D discrete (Discrete element method) domains, respectively, are developed to incorporate the mine site parameters of a study site in Australia. Both the models are calibrated and validated with measured mine data. The continuum numerical modelling method is used to investigate the change in permeability of the overburden strata due to underground extraction considering the full 3D nature of geology and mine layout. The discrete element modelling method is used to simulate the initiation and propagation of fractures, allowing the caving of overburden strata to be represented in a realistic manner, and the permeability enhancement of the strata overlying the goaf to be calculated from first principles. Permeability enhancement in the discrete element model is a direct function of the fractures induced in the deformation/caving process; fracture location, extent, aperture and connectedness. From the numerical modelling under the simulated condition for the mine studied here, it is predicted that the permeability of the caving zone from the goaf to five times the mining height increases by almost six orders of magnitude. In the fracture zone to approximately ten times the mining height, the change in permeability is predicted to be around two to three orders of magnitude. At the height of more than ten times the mining height the magnitude of permeability increased is predicted to be one to two orders of magnitude. CITATION:Khanal, M, Poulsen, B, Adhikary, D and Guo, H, 2018. Modelling of height of connective fractures during longwall mining, in Proceedings The Fourth Australasian Ground Control in Mining Conference (AusRock), pp 254–265 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 30, 2018

By T Medhurst

Recent developments in geophysical borehole log analysis using the Geophysical Strata Rating (GSR) are now routinely used in a number Australian coal mining operations. This allows development of 3D geotechnical strata characterisation models for a range of purposes. The availability of this data provides a means to identify relationships between ground conditions and ground behaviour. As a result, several new design methods have been developed to assist in the strata management process such as roof support, longwall shield design and shaft stability assessment. This paper outlines these methods and provides examples of their application. CITATION:Medhurst, T, 2018. Geotechnical strata characterisation using geophysics and its application for coal mine design, in Proceedings The Fourth Australasian Ground Control in Mining Conference (AusRock), pp 420–433 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 30, 2018

By A Penney, M J. Pascoe, R M. Stephenson

The empirical McCracken and Stacey stability and risk assessment method has been in use for more than 20 years to assess geotechnical stability issues for raise bored shafts. The methodology has been applied with various levels of success. Increasingly, trends in mining and civil tunnelling have been towards larger diameter, single pass, raise bored shafts to rapidly provide means of ventilation, material movement (ore passes), or emergency egress. Identifying and assessing potentially problematic zones before raise boring commences can allow for appropriate risk-based decisions on construction, or to investigate alternative solutions. The implementation of a proactive solution to raising through an identified weak zone is preferred to the application of an engineered solution to an area subjected to substantial instability or failure. Methods for investigating potentially problematic areas are discussed in this paper based on AMC’s benchmarking data. Proactive investigation programmes resulting from these investigations are also discussed. Previous publications discussing the benchmarking data have concentrated on Australian case studies. Increased efforts and recent updates have been made to expand the database to include international case studies. This has provided further refinement of lower bound ‘raise bore rock quality index’ (QR) values, and various rock mass parameters for stability assessments. CITATION:Penney, A, Stephenson, R M and Pascoe, M J, 2018. Raise bore stability and risk assessment empirical database update, in Proceedings The Fourth Australasian Ground Control in Mining Conference (AusRock), pp 434–445 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 30, 2018

By G Wyartt

In the Pilbara region of Western Australia, an iron ore mine is undertaking a high wall cut-back to improve stability and allow access to deeper ore deposits. Several sections of the wall have been classified low factor-of-safety due to unstable localised geology, and therefore an engineered approach to vibration critical blasting was required. The use of electronic detonators allowed multiple signature (seed) holes to be incorporated into a production blast adjacent to the low factor-of-safety area, therefore providing baseline vibration data to be used for future modelling with the added advantage of eliminating unnecessary pit closure downtime typically associated with a signature hole program. All subsequent blast patterns also incorporated multiple signature holes to provide additional data and allow continual updating – and therefore improved accuracy - of the blast prediction model. Electronic detonators and blast initiation systems were combined with advanced blast vibration modelling software to produce optimal timing sequences with predictable vibration outcomes. Although minimising vibration was the primary focus, blasting induced frequency was also a concern for the project team and therefore initiation sequencing was optimised to also avoid undesirable frequencies. Minor variations in ground factors (vibration transmission and attenuation) were noted, and therefore justified the inclusion of regular signature holes which allowed continual vibration model updates. Blasting results produced vibration and frequency measurements within allowable limits and closely resembled the predictive model. These positive results were achievable through the combination of electronic detonators, advanced modelling software and good onsite practices by engineering and on-bench teams alike. This project will remain ongoing as the pit progresses to deeper benches, and therefore the same methodology will be applied; quality and continual data collection, the use of electronic detonators, and optimisation via advanced vibration and frequency modelling software. CITATION:Wyartt, G, 2018. Vibration control blasting for low stability final walls, in Proceedings The Fourth Australasian Ground Control in Mining Conference (AusRock), pp 504–510 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 30, 2018

By B Crompton, A Berghorst, G Knox

Laboratory-based dynamic testing provides an invaluable tool in the development of rock bolts for use in highly stressed, burst prone rock masses. While in most cases the laboratory-based test method is not a direct comparison to an in-situ installation due to the purely axial loading and variations in boundary conditions, it does provide an indication of the performance of the tendon system under dynamic loading. The aim of the research described in this paper is to provide an understanding of the effect of the impact velocity of the impact mass during a laboratory-based dynamic test. Understanding the effect of boundary conditions of laboratory testing will improve Geotechnical Engineers understanding of the performance in an in-situ installation. In addition, due to the limited number of dynamic test facilities, an understanding of the effects of the boundary conditions will aid in the comparison of test results for different products from different test facilities. The research was conducted using an impact tester, whereby a known mass is raised to a known height defining the kinetic energy and velocity of the mass at the point of impact with the test sample after release. The impact velocity was varied between 2.7 m/s and 5.4 m/s, while the kinetic energy of the mass was maintained at 11.5 kJ. While a correlation between the impact velocity and strain rate of the system tested was established, due to the properties of the system tested, the range of impact velocity on which dynamic tests were conducted was insufficient to result in a considerable change in the average impact load, the cumulative proximal displacement and the cumulative maximum energy absorbed over multiple impulse. However, due to the reduction in the momentum of the impact mass the impact duration and displacement during each impulse in the series of impulses reduced. CITATION:Knox, G, Berghorst, A and Crompton, B, 2018. The relationship between the magnitude of impact velocity per impulse and cumulative absorbed energy capacity of a rock bolt, in Proceedings The Fourth Australasian Ground Control in Mining Conference (AusRock), pp 160–169 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 30, 2018

By B Roache, A Vakili, R Talebi

When a highly anisotropic or weak rock mass is subjected to high-stress conditions, it can lead to large ongoing deformations or squeezing ground conditions. Squeezing ground conditions can impose increased support costs, delays associated with rehabilitation, and disruption to production schedules. Ultimately, in more severe cases, it may result in complete drive closure. Several recent case studies investigated the squeezing mechanism and measures to control squeezing ground in underground mines and also to design appropriate ground support systems. Effective management of squeezing ground conditions requires a sound understanding of the failure mechanism and the driving forces. Once the failure mechanism is understood, the appropriate ground support system should be tailored to specifically manage the critical driving forces that control the squeezing mechanism. Support type, support stiffness, reinforcement length, support density, installation times and mining sequence all have important impact on the effectiveness of the support system. This paper provides a case study at the Ballarat Gold Mine in Australia, where drive squeezing was associated with foliated ground conditions located below 700 m depth. Numerical modelling was used to better understand the failure mechanism and the driving forces that lead to squeezing conditions. The effectiveness of various support types was compared to installed ground support performance. This has provided a credible methodology for assessing and optimising the selection of reinforcement in squeezing ground conditions. CITATION:Talebi, R, Roache, B and Vakili, A, 2018. Understanding and modelling squeezing ground conditions at the Ballarat Gold Mine, in Proceedings The Fourth Australasian Ground Control in Mining Conference (AusRock), pp 107–118 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 30, 2018

By T Roberts, S Talu

Steel wire weld mesh is a common industry standard surface support used in underground mining, traditionally installed with mining drills during the bolting cycle. As underground mining depth and stress increase, mining methods and their sequences at these depths place challenges on conventional surface support options. These challenges have provided a need for high capacity surface support options that improve development efficiency, reduce the need for secondary ground support installation and is easily installed with current mining equipment. A 5m2 mesh testing machine was built, suspending a 9500kg concrete slab, designed with multiple hold down points to test varying bolting patterns. Mesh load and displacement is accurately measured using a data acquisition system which pushes against the restrained mesh module with an available 200kN load and 1200mm displacement capacity. A testing program comparing conventional surface support, straps and combinations of both were tested for baseline results. New module designs incorporating existing mesh types and new design concepts were manufactured to allow for single pass installation during a bolting cycle. Nine mesh types, mesh/strap combinations and new mesh module designs were compared using the same test method. Based on these results, two high capacity mesh module types are produced. This paper will detail the test program, load and displacement results and underground mesh module performance, describing the two high capacity mesh modules function within the development cycle and manual handling. CITATION:Roberts, T, Talu, S and Wang, Y, 2018. Design and testing of high capacity surface support, in Proceedings The Fourth Australasian Ground Control in Mining Conference (AusRock), pp 303–322 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 30, 2018

By J Hadjigeorgiou, T R. Stacey

A ground support system is a combination of individual reinforcement and surface support elements that work together to retain and contain the rock mass. The various elements are subjected to external loads and to interactive loading between individual ground support system components. This paper focuses on the challenges in determining the capacity and behaviour of mesh, recognizing that installed mesh can be subjected to several loading mechanisms. Field observations from underground hard rock mines demonstrate that there are multiple types of damage and modes of failure of mesh. However, these are difficult to reproduce in a laboratory environment. A critical review has shown that existing mesh laboratory testing rigs reproduce very limited loading conditions that may not be representative of underground conditions. This has significant implications in quantifying and extrapolating the performance of mesh to ground conditions. CITATION:Hadjigeorgiou, J and Stacey, T R, 2018. Challenges in determining the capacity of mesh, in Proceedings The Fourth Australasian Ground Control in Mining Conference (AusRock), pp 280–290 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 30, 2018