Search Documents

By J Young, S Yu, P Moyo, M Powell, A Musunuri, B Bonfils, S Kanchibotla, P Yaroshak, V Jokovic

The appropriate design of liners continues to be an issue on many mills worldwide. Loss of milling capacity especially at liner change, uneven wear lives along the mill, substantial scrap on worn liners, excess mill down-time, undesirably short and unreliable wear lives are all common issues. This paper presents a designed approach to liner optimisation that follows a logical path of initial design and step-wise improvements based on liner wear monitoring. The target is to have a good liner design from start-up, then tune the profiles, heights and thicknesses based on wear monitoring. This is conducted as a team of liner specialist, site personnel and liner supplier. The application to the Pustynnoye SAG mill of JSC Altynalmas in Kazakhstan is presented. The increase in liner life by around 50% along with increased mill throughput of over 20% illustrate the huge benefit of the cooperative triumvirate approach through the gains that can be made in productivity and reduced liner costs.CITATION:Powell, M, Kanchibotla, S, Jokovic, V, Hilden, M, Bonfils, B, Musunuri, A, Moyo, P, Yu, S, Young, J, Yaroshak, P, Yalcin, E and Gorain, B, 2018. Advanced mine to mill application at the Barrick Cortez mine, in Proceedings 14th AusIMM Mill Operators' Conference 2018, pp 177–196 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 29, 2018

By A L. Randriamanjatosoa, G Small, C Greet

In flotation simulation models, the effects of pulp chemistry other than pH are often ignored and reduced to particles hydrophobicity or contact angle, neither of which can be measured readily in real time in an operating plant. The flotation response of a given sulphide mineral is known to be influenced and can be improved by changing the chemical characteristics of the pulp during grinding and flotation. The on-line measurement of pulp pH, potential, dissolved oxygen, temperature and oxygen demand of a process stream was completed with the PCM® (Pulp Chemistry Monitor) developed by Magotteaux in this study. The data generated together with relevant plant operating parameters were used to construct an empirical model and simulate the metallurgical performance of the ore. The same approach was also applied to laboratory flotation tests data using various grinding media types. The flotation models better fit the actual data when the chemistry of the pulp is taken into account.CITATION:Randriamanjatosoa, A L, Greet, C and Small, G, 2018. Effects of pulp chemistry on plant and laboratory flotation modelling, in Proceedings 14th AusIMM Mill Operators' Conference 2018, pp 423–432 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 29, 2018

By J Addai-Mensah, W Skinner, C Kelsey, J R. Kelly, E Baawuah

Comminution continues to be the most capital-intensive unit operation in mineral processing. The fundamental purpose of comminution is to liberate the valuable minerals so that they can be economically concentrated into saleable products. Declining ore quality characterised by lower grade and increased complexity requires significant energy consumption for comminution. Low-grade magnetite ores are typically fine-grained and require fine to ultra-fine grinding (P80 ~ 30 - 40 µm) to enhance its liberation from the typically siliceous gangue matrix. Historically, this has been achieved using multi-stage crushing and grinding technologies, which require high energy consumption with low energy efficiency. This motivated innovations in energy efficient technologies for comminution. Such technology has been developed in the IMPTEC super-fine crusher. It is an innovative, dry (with the potential to be operated wet), media-free, energy efficient crusher that can to reduce 10 mm feed particles to 19 – 30 µm with very low recycle loads. In this study, the mineralogical and physicochemical characteristics of crushed magnetite ore using the IMPTEC super-fine crusher have been investigated in comparison with those of rod milling. The super-fine crusher generated higher liberated magnetite minerals in the – 300 + 212 µm and < 45 µm size fractions compared to rod mill. Both comminution devices generated large low-grade hematite and goethite middlings. However, the rod mill produced higher locked/unliberated hematite and goethite compared to that of the super-fine crusher. Quartz mineral had the highest liberation irrespective of the comminution device used. The super-fine crusher generated higher entrapment of other minerals within the silica matrix compared to the rod mill. The breakage mechanism of the super-fine crusher which is predominantly through high compression with shear, generated improved mineral liberation in the coarse size fractions compared to the predominant abrasion and attrition breakage mechanisms of rod milling. The higher mineral liberation generated by the rod mill is potentially due to the prolonged batch milling of the ore compared to the single-pass open circuit of the super-fine crusher.CITATION:Baawuah, E, Kelsey, C, Kelly, J R, Addai-Mensah, J and Skinner, W, 2018. Mineral liberation studies of IMPTEC super-fine crusher – 130 crushed product, in Proceedings 14th AusIMM Mill Operators' Conference 2018, pp 313–326 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 29, 2018

By K Blay, C McCamley, P Petrucci

The Newmont Boddington Gold (NBG) processing plant was designed for 35Mt/y with ball mills expected to deliver a combined new mill feed rate of 4837 tonnes/hr. Since beginning commercial production in late 2009, the plant has steadily increased throughput to meet design capacity in 2014 and reached 37 Mt/y in 2015. Through improved efficiencies, changes to the milling circuit have taken place since commissioning to take the plant beyond its design to an actual throughput of 39.0 Mt in 2017 and a budgeted throughput of 39.4 Mt/y this year.The NBG milling circuit has four parallel ball mills, each consisting of a 7.9 x 13.4 m ball mill with twin 7.5 MW fixed speed motors in closed circuit with twelve 650 mm cyclones. Each mill is fed by two wet screens with the undersize gravitating to a mill discharge hopper where it is combined with the ball mill discharge and pumped to hydrocyclones for classification. The cyclone underflow is re-ground to a target P80 of 150 µm.This paper will focus on process improvements made to the NBG milling circuit which include cyclone reconfiguration, fine screen panel redesign, implementation of an expert control system, mill power draw increase and grinding media changes to take NBG beyond its design throughput.CITATION:McCamley, C, Petrucci, P and Blay, K, 2018. Going beyond design at Newmont Boddington Gold, in Proceedings 14th AusIMM Mill Operators' Conference 2018, pp 497–508 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 29, 2018

By D Baas, J Le, R Braun, R Chandramohan, K Hollis, G Lane

The Phu Kham Copper-Gold Operation (Phu Kham) is located in northern Laos, approximately 140 kilometres from the capital, Vientiane. The operation is a producing asset for Australian-based copper and gold producer, PanAust Limited (PanAust) and is operated by Lao-registered company, Phu Bia Mining Limited (Phu Bia Mining). PanAust holds a 90 % interest in Phu Bia Mining. The Government of Laos owns the remaining 10 %.The Phu Kham Operation has recently undergone a series of process improvements to treat the anticipated competent ores scheduled for 2017 and 2018. The operation’s comminution circuit, which comprises a semi-autogenous (SAG) mill and two ball mills, each with 13 megawatts (MW) of installed power, was expected to be SAG mill limited when treating competent basement rock. Ausenco Services Pty Ltd (Ausenco), was engaged to help optimise and enhance the productivity of the Phu Kham comminution circuit over an eight-month period. The work involved participating in and overseeing the redesign of the SAG mill liner systems and developing operational strategies for maximising throughput through to the end of mine life. Ausenco’s comminution optimisation tool, Ausgrind, was used to benchmark and analyse plant data with empirical models, predict circuit performance for varying ore characteristics and evaluate liner wear and predict the life for varying operating parameters. Variances between the actual and the predicted values were assessed in detail to identify missed opportunities, and guiding operating parameters were redefined to maximise throughput and productivity. In combination with the redesigned liner system, optimised process controls for varying ore competencies, and improved operational practices and troubleshooting strategies, increased Phu Kham overall production, exceeding the milling capacity when treating competent ores. CITATION:Chandramohan, R, Braun, R, Lane, G, Hollis, K, Le, J and Baas, D, 2018. SAG mill optimisation and increasing throughput at the Phu Kham Copper-Gold Operation – a success story, in Proceedings 14th AusIMM Mill Operators' Conference 2018, pp 113–128 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 29, 2018

By E M. Wightman, C L. Evans

A recent survey of mineral processors undertaken as part of the International Mineral Processing Council (IMPC) Education Commission identified mineralogy as one of the key skills required for mineral processors (the other key areas being comminution, flotation, physical separation, sampling and extractive metallurgy). Past experience in a number of operations has shown what can be achieved when the data outputs from mineralogical tools are coupled with people with the right skills who can transform the data into actionable information. This paper reviews what has been done successfully in plant operations over a period of more than four decades and gives examples of a range of applications with both long and short-term objectives. The examples demonstrate the usefulness of mineralogical data – both basic and complex – in optimising mineral processing operations, whether the data are applied in a simple analysis or in more complex modelling. Similarly, the examples show the range of options available for operations to access the mineralogy information they need – through in-house experts and equipment based in centralised technology centres, through on-site equipment and experts or through external laboratories and consultants.The examples from industry highlight the huge potential benefit of including mineralogy as an integral part of operational best practice and raise the question of why more operations do not utilise what should be readily available data. Successful application of mineralogical data requires skilled people to generate relevant data of the required quality, together with skilled people to interpret the data (this may be the same person). And, as in any project, corporate recognition of the value of this approach to best practice is required to ensure continuing support. With fewer university courses providing courses in process mineralogy to undergraduate mineral processing engineers and chemical engineers, there is an increasing lack of knowledge about what mineralogical information is needed, how to get the required data and, equally importantly, how to turn the data into useful information.CITATION:Evans, C L and Wightman, E M, 2018. Understanding minerals in mineral processing – the basics and beyond, in Proceedings 14th AusIMM Mill Operators' Conference 2018, pp 363–376 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 29, 2018

By R Bose, M Bovell, G Cheong

Grinding media is a major consumable in mineral processing and therefore decreasing costs associated with its consumption is regularly considered a key goal for the minerals processing industry. Grinding media manufacturers have historically developed steels with improved wear life for their products as a way of delivering incremental media quality improvement. This has included increasing carbon levels from low-to-medium carbon steels up to the eutectoid carbon composition of 0.77% where the relationship between higher carbon and better wear performance is well understood. Producers today will regularly use grades in excess of 0.8% to further improve wear performance particularly for rolled grinding media.This paper first introduces the demonstrated relationship between this increased carbon content and improved wear resistance along with metallurgical rationale behind the high carbon production process and limitations. To test the performance improvement associated with the higher carbon steel grade, a series of Marked Ball Wear Tests (MBWT) were carried out. This paper also explores the relationship between ball properties, test methodology and wear performance and concludes by correlating increased carbon grade with a reduced consumption rate of between 3.1% and 6.1% in the tests conducted.CITATION:Bovell, M, Bose, R and Cheong, G, 2018. Improved forged grinding media performance with carbon content greater than 1.0%, in Proceedings 14th AusIMM Mill Operators' Conference 2018, pp 559–570 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 29, 2018

By O Arafat, R E. McIvor, K M. Bartholomew

It is well known in the industry that good classification system performance is vital to efficient ball mill circuit performance. But what is meant by good classification system performance, and how is it achieved? Unfortunately, the perceived complexity of classification systems, and the day-to-day time demands placed on the practicing metallurgist, all too often put the low-hanging fruit of classification system optimisation in the ‘I’ll do it later’ basket. Additionally, lingering confusion about basics such as the relationship between circulating load ratio and ball mill circuit performance makes the optimisation objective seem nebulous to both plant metallurgist and designer.Some of this confusion can be eliminated by taking a step back from the overwhelming detail of sharpness of separation curves, circulating load ratios, cyclone feed pressures, vortex and apex sizes etc, and focusing on the purpose or function of the classification system – to apply mill power to particles that need further size reduction! The classification system efficiency (CSE) metric captures how well the classification system is performing its function with two quick and easy size distribution analyses.Once CSE is understood and implemented as the optimisation criteria, well-tested methods for improving CSE can be implemented and quickly measured at plant scale to give confidence that the right change was made.This paper will describe CSE and how it is measured in practice. Next, a guide for improving CSE through manipulation of design and operating variables in the classification system will be provided. Examples and case studies will illustrate the gains in ball mill circuit efficiency that can be achieved by maximising CSE.CITATION:Bartholomew, K M, McIvor, R E and Arafat, O, 2018. A guide to maximising ball mill circuit classification system efficiency (CSE), for operators and equipment designers, in Proceedings 14th AusIMM Mill Operators' Conference 2018, pp 553–558 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 29, 2018

By J Seppelt, G S. Lane, E Wang

Newcrest’s Cadia concentrator operated from 1998 to 2012 with a traditional SABC grinding circuit treating Cadia open pit ore. The Cadia comminution circuit was well characterised through surveys and data that are available in the public domain, and became a benchmark standard for the industry and practitioners modelling large SAG mill based circuits. In 2012, the HPGR-based crushing circuit was introduced in front of the SAG mill to increase throughput when treating the Cadia East ore that was derived from an underground block cave. This ore was expected to be more competent and have a coarser run-of-mine size distribution.Numerous previous papers have described the design and commissioning of the Cadia HPGR-based circuit.This paper describes the improvement in comminution energy consumption resulting from the introduction of the HPGR, including identifying the impact of process complexity and an increase in ancillary energy consumption for conveyors, screening, and crushing.CITATION:Lane, G S, Seppelt, J and Wang, E, 2018. Quantifying the energy efficiency transformation at Cadia due to HPGR crushing, in Proceedings 14th AusIMM Mill Operators' Conference 2018, pp 141–152 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 29, 2018

By D Walker, A Tsvetkov, P Voigt, O Kloiber-Deane

The GPM Gold Operation has been employing an Albion Process™ plant at its Sotk (Zod) gold mine in Armenia since 2014. Long term data from the operation is now being published for the first time. The data presented includes concentrate throughput, as feed to the Albion Process™ plant (tonnes per day), sulphur grade in concentrate (% S), total sulphide sulphur oxidation in the Albion Process™ plant (% SOx) and gold recovery from Albion Process™ plant residues (%). The data provides a basis for evaluation of the effectiveness of the commissioning, ramp up and operation of the Albion Process™ plant. Notwithstanding the impact of a slower concentrator commissioning than expected, the plant demonstrates Series 1 behaviour on McNulty ramp up curves, indicating successful commissioning and fast ramp up. Interrogation of the data and operational experience indicates that this successful operation is a result of a process that is flexible, robust and stable, one that was designed well based on solid testwork results and pilot plant trials during the study phase undertaken by Glencore Technology and Core Resources, and where the local operators were provided with appropriate training in operation of the plant. CITATION:Voigt, P, Walker, D, Kloiber-Deane, O and Tsvetkov, A, 2018. Ramp-up and long-term performance of the Albion Process™ plant at GeoProMining Gold Armenia, in Proceedings 14th AusIMM Mill Operators' Conference 2018, pp 339–350 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 29, 2018

By G R. Ballantyne, V Souto, K Bartram

Particle sorting allows partially liberated minerals to be separated prior to energy intensive fine grinding. Sensors select particles for separation and air, water or mechanical ejectors are used to physically deflect those selected. To achieve effective separation there has to be sufficient liberation, accurate detection and presentation of a separated monolayer of particles. These three physical constraints determine the particle size limits, the sorting technology utilised, the separation efficiency, and the throughput that can be achieved. The combination of all these factors controls the effective limits on the degree to which sorting can reduce the specific comminution requirements and increasing energy efficiency. This paper will explore two case studies: the application of sorting in base metal mining and precious metal mining.CITATION:Ballantyne, G R, Hilden, M, Bartram, K and Souto, V, 2018. Characterising energy efficiency of particle sorting, in Proceedings 14th AusIMM Mill Operators' Conference 2018, pp 531–540 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 29, 2018

By J Geronimo, P Kumar, Z Yussupova, M Yahyaei, M Powell

This work goes beyond the general perception of how the well-known mine to mill process can be applied, by applying deeper knowledge along the mining chain. Grade deportment and dilution are considered at the mining stage, and modelled with the new SMI blast movement simulator, linking with the block model data. Assessing the shift to a considerably more competent section of the orebody is quantified via substantial milling trials at standard and higher-intensity blasts. These were stockpiled for batch processing through the mill to ensure feed integrity. The trial work included operating the mill at widely different fillings to develop Grindcurve milling responses. Additionally, model informed process control is initiated via a mill prediction tool.It has been found that accounting for blast movement for the higher intensity blasts could generate additional value of around $1.5M per blast. With the high-intensity blast and changing mill control, the plant was easily able to exceed projected mill throughputs with the far more competent Pipeline ore. Strategies to shift the workload and debottleneck the milling circuit were proposed and proven during the milling trials, demonstrating an increase in throughput of 7 per cent despite running at a lower SAG mill speed, and potential of 16 per cent for increasing the SAG mill to standard operating speed. A number of process improvement opportunities have been identified to enhance current productivity and ensure long term capability to process the considerably more competent future ores. All of this is being linked in with the major digitisation program at the Barrick Cortez site, with an objective of linking all the data into a mine-wide process optimisation system, that can embed the processes by providing process-wide data access and production support via the future dynamic models linking ore body knowledge to productivity along the full process chain.CITATION:Powell, M, Yahyaei, M, Geronimo, J, Yussupova, Z and Kumar, P, 2018. The designed approach to mill liner optimisation – experience at Pustynnoye mine, Kazakhstan, in Proceedings 14th AusIMM Mill Operators' Conference 2018, pp 595–612 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 29, 2018

By M Randall, P Ebzery, F Burns, C Aisthorpe, P Blanz

SAG Mill process control classically maintains the SAG mill volumetric filling within a set operating range. Typically a SAG mill weight measurement, by either bearing pressure transducers or load cells, is used as an inferred measurement of volumetric filling. To maintain volumetric filling within a set operating range the SAG weight setpoint use for process control requires regular review due to changes in SAG mill charge density (rock:ball ratio) and the wearing of mill liners. At Lihir Gold Mine in Papua New Guinea, the use of SAG mill weight for process control is additionally complicated by compromised load cells and drifting bearing pressure measurements. The need for an improved method of measuring and controlling volumetric filling led to the recent installation of the Outotec MillSense, a SAG mill toe angle instrument. This paper presents the integration of the toe angle control in to the Lihir SAG mill process control philosophy as replacement for the traditional mill weight control.CITATION:Burns, F, Aisthorpe, C, Blanz, P, Randall, M and Ebzery, P, 2018. Toe angle measurement for SAG mill control at Lihir gold mine, in Proceedings 14th AusIMM Mill Operators' Conference 2018, pp 59–76 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 29, 2018

By C M. Standen

The SAG mill at Rasp Mine has undergone a number of liner design modifications since commissioning in 2012, making liner wear and failure difficult to predict from historical data. During 2017, several instances of liner failure or near failure were experienced resulting in unplanned downtime for emergency relines or to patch liners in the lead up to a planned shutdown. The strategy for relining mills is often to minimise the frequency of relines (and subsequent shutdown costs) by extending liner life, achieved through design modifications. However, it was observed that as the Rasp SAG mill liners wear, mill performance declined with power draw increasing and throughput declining. Opportunity and inefficiency costs start to erode the revenue per additional tonne milled for a given set of liners, and in turn the benefit of delaying relines. As such, optimising the frequency of relines becomes a trade-off between reline costs and opportunity/inefficiency costs in delaying relines. The aim of this paper is to demonstrate a frame work for analysing costs using a marginal economic analysis with the assumption that the Law of Diminishing Returns can be applied to the life of mill liners. The SAG mill operating variables can be modelled to determine their impact on costs and an optimal reline point can be defined where the total costs are minimised. This prevents unexpected failures due to accelerated wear by providing justification to reline earlier and thereby allowing efforts to be focused on sustaining milling performance.CITATION:Standen, C M, 2018. An economic approach to optimising mill reline frequency – a case study of SAG mill relines at Rasp mine, in Proceedings 14th AusIMM Mill Operators' Conference 2018, pp 197–206 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 29, 2018

By N S. Weerasekara, S Town, E Lessing, J A. De Torres

Philsaga Mining Corporation (Philsaga) had three main aims in converting their lining system from steel to metal cap. They wanted to increase mill availability, minimise localised high wear and optimise particle breakage to deliver increased efficiency within the milling circuit. Combining Discrete Element Method (DEM) modelling and empirical interpretation of liner wear resulted in a rigorous approach to understanding the impact of mill liners on overall mill performance. This new understanding was subsequently used to not only derive a new lining design to optimise performance and thereby improve overall plant economics, but also to guide further lining development.In this work, detailed DEM modelling, developed from actual plant data, together with optimising liner design for wear paved the way towards the installation of a Metal Cap lining system at Philsaga’s Ø6100 mm SAG Mill. The results were a reported increase in SAG mill throughput of 16 – 20 per cent due to improved breakage through more efficient use of installed power, a reduction in localised high liner wear with overall increase in liner life and reduction in liner replacement time. Site also reported an increased gold recovery of 2 per cent which the improved breakage might have contributed to. This paper will present the design challenges and compare the Metal Cap lining systems performance against Steel lining system. CITATION:Weerasekara, N S, Lessing, E, Town, S and De Torres, J A, 2018. Metal cap versus steel lining system at Philsaga Mining Corporation’s Ø6100 mm SAG mill, in Proceedings 14th AusIMM Mill Operators' Conference 2018, pp 653–664 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 29, 2018

By M L. Muller, A R. O’Donnell

The Mount Isa Mines (MIM) Copper Concentrator has an extensive history of reagent trials, with different reagents coming in and out of favour over the years. The research and use of carbon depressants is particularly prevalent, as carbonaceous pyrite is a major source of concentrate dilution. Years of research led to the use of naphthalene sulphonate due to its excellent carbon depression properties. However, due to rising reagent costs carbon depression ceased in the late 1990s. This led to the loss of knowledge about the use and value of naphthalene sulphonate. Cyanide is used at the Copper Concentrator for the sole purpose of pyrite depression and over the years multiple projects have been devoted to finding alternatives to it. In 2012 the neighbouring MIM Lead-Zinc Concentrator replaced cyanide with naphthalene sulphonate which resulted in cost savings and the elimination of a hazardous reagent. In 2013, plant trials were conducted at the Copper Concentrator in hopes to replicate the outcomes obtained at the Lead-Zinc Concentrator. The results of the trials conducted at the Copper Concentrator showed that naphthalene sulphonate could not replace cyanide and this work was set aside to pursue more promising projects. Further research conducted in 2014 found that mineralogy and a better understanding of the depressing mechanism of naphthalene sulphonate held the key to improved pyrite depression at the Copper Concentrator. The findings showed that Mount Isa copper ore contains two forms of pyrite; euhedral pyrite (cubic pyrite) and framboidal pyrite (carbon rimmed spheres of pyrite), both of which require different reagents to sufficiently depress them. Naphthalene sulphonate was found to be an excellent carbon depressant, suitable for depressing graphite and framboidal pyrite, whilst cyanide specifically targets euhedral pyrite.In 2015 laboratory test work was conducted to examine the use of naphthalene sulphonate in conjunction with cyanide to selectively target both forms of pyrite. This work led to a full plant trial, the results of which showed a significant increase in plant performance, with higher copper concentrate grades and recoveries being achieved. This paper aims to focus on the benefits and importance of understanding past work and linking a detailed knowledge of feed mineralogy to reagent selection for improved plant outcomes.CITATION:O’Donnell, A R and Muller, M L, 2018. Selectively targeting hydrophobic gangue minerals at the Mount Isa Mines Copper Concentrator, in Proceedings 14th AusIMM Mill Operators' Conference 2018, pp 413–421 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 29, 2018

By A Price, D Okle, K Brooks

The operation of flotation plants has been improved over the years by use of fundamentally based design techniques, a better understanding of reagent chemistry, online metal analysis and the use of digital control systems. However, optimal operation of flotation banks is not consistently achieved using manual operation. The reason for this is that the system is a highly interacting one, with changes in air addition, cell interface level and reagent dosages all being available, without it necessarily being clear as to which change should be made for a particular situation.This situation is made more complex by the fact that the feed to a flotation bank can vary in flowrate, composition and density over a fairly short period of time. It is not possible for a human operator to reject these disturbances, given the extent of the operation that is typically being monitored.Model predictive control (MPC) is a control and optimisation technique, developed in the oil refining industry, that aims to manage just such interacting multiple input multiple output (MIMO) systems. This technology makes use of linear dynamic models of the plant, that are experimentally derived. These models are then used in a receding horizon strategy to determine an optimal trajectory of the inputs to the system.MPC has been applied to four areas of the lead zinc flotation unit at Mount Isa mines. A total of 31 cells are being controlled by the system, which varies air to the cells, levels and reagent addition on a minute-by minute basis. The MPC controls concentrate and tail grades, reagent dosages, as well as recoveries to ranges set by the plant metallurgists.The development of the MPCs is discussed, together with the benefits realised. The key factors in insuring an ongoing return on investment are described.CITATION:Price, A, Okle, D and Brooks, K, 2018. Glencore Mount Isa lead zinc flotation circuit – experiences from the implementation of model predictive control, in Proceedings 14th AusIMM Mill Operators' Conference 2018, pp 101–110 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 29, 2018

By T D. H McGrath, W P. Staunton

Benchmarking, comparing an operation or process with the industry standard, is known to be a useful method for identifying plant optimisation opportunities, and in many cases providing the pathway to realise the benefits. The difficulty is generating the database of plant data necessary for a benchmarking exercise. Larger companies can benchmark internally; this option is not available to smaller companies, and the full value can only be realised with a comprehensive “industry wide” approach.The Gold Technology Group at Curtin University through the AMIRA P420 series of projects has undertaken several comprehensive metallurgical industry surveys in the gold industry over the last two decades. Analysis of these surveys has demonstrated areas where many operations can benefit from re-assessment of their operating practices.This paper will review the work undertaken by the Group in this area, in particular the 1999 surveys of gold companies in the Australasian region, and the 2012 international survey of the industry. The challenges of, and opportunities arising from these surveys will be discussed. Some of the highlights from analysis of these databases will be presented as well as noting changes in processing practices observed by the Group over the last 20 years.CITATION:McGrath, T D H and Staunton, W P, 2018. Keeping up with the Joneses – the value of industry surveys and benchmarking, in Proceedings 14th AusIMM Mill Operators' Conference 2018, pp 509–516 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 29, 2018

By L Mikhael Gurieff, D Baas

The Phu Kham Copper-Gold Operation (Phu Kham Operation) is located in the Lao People's Democratic Republic and is owned and operated by the Lao-registered company, Phu Bia Mining Limited (PBM). Australian-headquartered copper and gold producer, PanAust Limited holds a 90 per cent interest in PBM; the Government of Laos owns the remaining 10 per cent. The Phu Kham Operation was commissioned in 2008 with an initial concentrator nameplate throughput of 12 million tonnes per annum (Mt/a). Subsequent improvement projects, including the Phu Kham Upgrade Project (PKU), completed in 2012, and the Phu Kham Increased Recovery Project (IRP), completed in 2013, increased the design throughput to 18 Mt/yr. In 2016, the actual mill throughput exceeded 19 Mt/a, this throughput is budgeted to be maintained until the end of 2020.The concentrator flotation circuit upgrade, completed during the IRP, called for a non-selective bulk sulphide concentrate to be generated from the rougher circuit. This in turn caused the mechanical flotation cells in the cleaner circuit, particularly those in the second cleaner bank, to become volumetrically overload. The overload reduced the cleaner circuit performance to approximately 92 per cent copper recovery at a 23 per cent copper concentrate grade, below the expected 95 per cent recovery. This bottleneck restricted copper units entering the plant to approximately 14.5 tonnes per hour (t/h) due to uncontrolled recirculating load build-up in the mechanical cleaning circuit.Maintaining the operating methodologies would have led to a copper production shortfall beyond 2016, to address this shortfall the Phu Kham Operation looked to optimise the Jameson Cell and mechanical cleaner circuit performance. The work included fundamental application of flotation practice and modelling, mineralogical analysis, bubble size analysis, plant surveys and test work. The results were used to develop and implement an innovative automated control system strategy incorporating flotation theory and operating strategies. The automation has the ability to quickly adapt to disturbances in the circuit and maintain optimised performance with little or no intervention by flotation operators.Upon completion, cleaner recovery increased to 95 per cent at a final concentrate grade of 23 per cent copper, and copper units entering the plant increased to 17.5 t/h.CITATION:Baas, D and Mikhael Gurieff, L, 2018. Developing flotation circuit control and automation for the Phu Kham Copper-Gold Operation concentrator, in Proceedings 14th AusIMM Mill Operators' Conference 2018, pp 37–58 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 29, 2018

By A Parry, C Fitzmaurice

After conducting laboratory ore sorting testwork on samples of a low grade nickel ore stockpile at Western Areas’ Flying Fox nickel mine, a mobile crushing, screening and ore sorting plant was located adjacent to the stockpile. An initial two month trial of the ore sorter program proved successful and was extended to process the entire Flying Fox low grade stockpile in a further four month campaign. A total of 167 660 t of low grade ore was processed, providing highly upgraded feed trucked 26 km to the Cosmic Boy concentrator. A more than three-fold grade increase was achieved on ore sorter accepts. The moderately upgraded fines that by-passed the mobile ore sorter were also subsequently blended into plant feed. This paper describes the mineralogy of the Flying Fox low grade ore, the mobile ore sorting campaign and provides some commentary on the economic and environmental benefits achieved in the ore sorting campaign. The ore sorting campaign demonstrated the benefits of being able to utilise mobile ore sorting equipment temporarily located adjacent to sub-economic low grade stockpiles in order to effectively treat these stockpiles and produce viable plant feed.CITATION:Parry, A and Fitzmaurice, C, 2018. The upgrading of low-grade nickel ore stockpiles at Western Areas Ltd Forrestania operations, using a mobile ore sorting plant, in Proceedings 14th AusIMM Mill Operators' Conference 2018, pp 541–550 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 29, 2018