Search Documents

By J. L. Brinkman

"One of the most common emissions from detonating explosives are nitrogen oxides (NOx), which are potentially deadly if inhaled. Lab studies estimate emission quantities, though great variation is shown based on site-specific conditions, and lab tests may not fully represent field results. Field VALUES (have not been measured due to the vast area affected. OSMRE recently promised to release a ruling regarding surface mine NOx production. Once the ruling is implemented, it may eventually be necessary to monitor site-specific NOx production from blasting. A small unmanned aerial vehicle system (sUAS) is able to carry a NOx gas monitor, rapidly travel to the blast location, and to follow resulting clouds of dust and emission gasses. This project will perform laboratory tests to expand on current estimations, determine an optimal method for collecting data, and evaluate the ability for this unique application of sUAS to assist in health risk assessment for mine employees and nearby communities. Additionally, large initial NOx concentrations do not necessarily correlate to unsafe conditions, and this project will be ground breaking in observance of surface blasting emission dispersion. The project is still in early phases at the time of submission for this paper (Nov 1, 2017). Therefore, this paper focuses primarily on summarizing background research related to the project and a description of the project plan. INTRODUCTION Nitrogen oxide gases (NOx) are common emission by products of surface mine blasting. These gases can potentially cause risk to human health and safety, both for mine workers and communities near the blast site. However, these emission quantities are largely unmeasured and no attempts have been made to relate these VALUES (to human health risk. The primary objectives of this project are to determine actual quantities of emission gases produced during surface blasting, to evaluate immediate and long-term risks to nearby people, communities, and ecosystems, to develop a system for mine employees to easily monitor emission and risk levels, and then provide guidelines for mitigating health risks based on a location’s emission results. BACKGROUND Current research regarding health risk produced by surface mine blasting NOx emissions is extremely lacking. Estimations have been made based on laboratory research, though these same test results show wide ranges of possible gas quantities produced based on site-specific conditions. Even if these estimations are accurate, no method has been created to relate gas quantity produced to human exposure concentrations. To further understand this field, background research was studied pertaining to blasting emission gas formation, laboratory and field measurements, harmful effects of blasting emission gases, and relevant government regulations. Background on Blasting Emission Gases"

Jan 1, 2018

By Gökçe Törenli, Okay Tutar

"Predicting the performance of plant-scale comminution circuits is essential to monitor the energy use and product size distribution, allowing us to control and optimize the whole process. In the light of this issue, with the assist of recent technologies, simulation techniques utilize the chance of putting the theory into practice in the most accurate way. For this purpose, this study aims to evaluate and optimize the efficiency of a plant-scale ball mill circuit by using perfect-mixing ball mill model on a simulation environment. The comminution circuit is selected from a specific copper-ore processing plant in Turkey. The essential parameters which are required for this study such as fresh feed Bond work index, size distribution etc. are determined by laboratory experiments. The forecasted data which are calculated by third-party software will be compared by the industrial operating data, in order to determine the performance of comminution circuit. In addition to that, this methodology provides a greater ability to analyse, optimize and understand the comminution circuit of ore treatment plant. The authors believe this work will provide supplementary data for further studies on simulation and subsequent optimization of comminution circuits.INTRODUCTION By the assist of mathematical models of the grinding mills and classifiers, simulation of the grinding circuits become more common in comminution because it is relatively economical and able to consider many variables simultaneously. It’s proceeds depends on the accuracy of the models and capability of reflect real operations. Computer-based simulation studies would provide the quantified information about the effects of the proposed changes on the comminution circuit performance in terms of size distribution, mass flow rates, equipment efficiency etc. Then the mentioned data used in order to check the suitability of the current equipment to the modified conditions, and for equipment selection. The outputs of circuit could also be used to estimate downstream flotation circuit performance because the general aim in this study is to The aim of the study is to investigate optimum operating variables and achieve p(80) size of 57 µm and 64 % of -36 µm particle in hydrocyclone overflow stream, which is optimum for that porphyritic copper ore for best concentrate recovery after flotation process in specific copper ore comminution circuit by using modelling and simulation techniques. Sampling survey was carried on the fine ore bin in order to perform Bond work index test and determine work index value (Wi). Thereafter mass balancing, using the size distribution data and tonnages, models for ball mills and hydrocyclone were developed. Finally, the circuit performance were investigated by computer simulations via JKSimMet software."

Jan 1, 2018

By J. F. Burr, D. P. Snyder, G. W. Luxbacher

"The Mine Improvement and New Emergency Response Act (MINER Act) of 2006 established the Office of Mine Safety and Health (OMSH) within NIOSH and provided authority for awarding contracts related to the development and implementation of new mine technology and equipment. Subsequently, Congress provided additional funding to NIOSH to initiate and continue the program. OMSHR has fulfilled this Congressional mandate through annual Broad Agency Announcement (BAA) solicitations, directed Requests for Proposals (RFP) and Inter-Agency Agreements (IAA), and has further expanded the program through capacity building BAA contracts with U.S. university mining departments in the areas of mine ventilation and ground control. This paper describes the extramural funding program and broadly examines the results of the 150+ contracts issued to date, grouped into key focus areas. INTRODUCTION The Mine Improvement and New Emergency Response Act (MINER Act) of 20061 established the Office of Mine Safety and Health Research (functioning as the Office of Mine Safety and Health Research or OMSHR) within the National Institute for Occupational Safety and Health (NIOSH), and provided authority for awarding contracts related to the development and implementation of new mine technology and equipment. The OMSHR external contracts program was formed in accordance with the MINER Act and has since issued over 150 contracts focused on worker health and safety. Initial funding for this program was provided by Congress through two Emergency Supplemental Appropriations (ESA) and was focused on emergency oxygen supply, communications and tracking, and refuge chambers (also referred to as refuge alternatives). Since the MINER Act, Congress has continued to fund the program through the annual NIOSH mining appropriation. The program was supplemented starting in 2009 with an academic capacity building program directed toward developing university tenure-track faculty and facilities and supporting graduate students in the area of mine ventilation; ground control was added as an additional focus area in 2011. A short synopsis of each contract is published on the NIOSH Mining website2 and final reports are available in digital form on request. A summary of the progress OMSHR has made over the 10-year period since the Act was published previously.3"

Jan 1, 2018

By M. Dadvand, G. Kipuros, A. Dadvand

"The ability to codeposit fillers within a nickel matrix has led to the production of a new generation of cermet coatings with properties useful for various applications. Hexagonal boron nitride (hBN) is a ceramic-type particulate matter with thermal conductivity, thermal stability, inertness, and lubricity properties that allow it to be codeposited. In this paper, a method was developed for modifying hBN surfaces to allow them to be uniformly dispersed in water-based solutions such as an electroless nickel plating bath. hBN surface modification improved wear performance of the electroless plated cermet due to enhanced interaction between the particulate and nickel matrix. RÉSUMÉ La capacité à effectuer un dépôt simultané de charges dans une matrice nickel a abouti à la production d’une nouvelle génération de revêtements cermet (une combinaison de céramique et de métal) dotés de propriétés très utiles pour diverses applications. Le nitrure de bore hexagonal (h-BN) est une matière particulaire de type céramique utilisée pour ses excellentes conductivité et stabilité thermiques, son inertie ainsi que son caractère lubrifiant, qui permettent son dépôt simultané. Cet article explore une méthode mise au point pour modifier les surfaces du h-BN de manière à ce qu’elles se répandent uniformément dans des solutions aqueuses telles qu’un bain de dépôt autocatalytique de nickel. La modification des surfaces du h-BN a amélioré la résistance à l’usure du placage autocatalytique du cermet en raison d’une interaction accrue entre la matière particulaire et la matrice nickel.INTRODUCTION Electroless nickel alloy coatings can be used for many applications; however, the need for improved tribological properties such as higher wear resistance and better lubricity has increased interest in incorporating particulates (fillers) into the nickel matrix by codepositing the particulates with nickel during the plating process. The selection of the particulate type depends on the desired properties (Sahoo & Das, 2011; Sudagar, Lian, & Sha, 2013). In terms of tribological applications, electroless nickel-based composites are categorized mainly into lubricating and wear-resistant composite coatings depending on the type of particles incorporated. The electroless nickel-phosphorus (Ni-P) composite coatings are composed of codeposited solid lubricants such as polytetrafluoroethylene (PTFE), graphite, WS2, MoS2, and hexagonal boron nitride (hBN) and, compared to nanocomposite electroless Ni-P coatings, they demonstrate a lower coefficient of friction. On the other hand, the nickel-phosphorus wear-resistant composite coatings are composed of hard particles such as silicon carbide (SiC), aluminum oxide (Al2O3), boron carbide (B4C), silicon nitride (Si3N4), diamond, tungsten carbide (WC), and zirconium oxide (ZrO2) and, compared to nanocomposite electroless Ni-P coatings, they have higher hardness and better wear resistance (Sahoo & Das, 2011; Sudagar et al., 2013; Parucker, Klein, Binder, Ristow, & Binder, 2014; Chakarova, Georgieva, Petrova, Dobreva, & Stoychev, 2016)."

Jan 1, 2018

By N. N. Orekhova, I. V. Shadrunova, N. G. Novikova, N. ?. Volkova

The purpose of the research is scientific substantiation and formulation of strategy and technical solutions of handling liquid wastes of plants producing and refining copper-zink pyritic ores. In the course of research studied are chemical composition of technogenic waters of mining plants as well as water and alluvia of intake river within and outside a sanitary zone of Southern Ural mining plant using inductively coupled plasma mass-spectrometry and X-ray fluorescence analysis techniques. A particular focus is made on microcomponent composition. Novel data on Cd, Li, Be, Mn, Co, Cu, Zn migration with technogenic flows and accumulation of these elements in alluvia is obtained. It is showed that extraction of valuable components from technogenic waters is a novel problem for refiners that can be solved only in cooperation with mining industry ecologists. Laboratory research of selective copper and zink extraction into corresponding practical products by galvanocoagulation and sulphide precipitation is carried out. Common factors of phase formation are studied using physicochemical modeling, X-ray phase analysis and electronic microscopy. Methods of intensification of processes and increasing of extraction ratio of metals in products are elaborated. A technology of comprehensive processing of undersoil waters is proposed. Enlarged laboratory and pilot plant tests of technological solutions for protecting hydrosphere and extracting metals from mine waters carried out on several plants of UMMC-Holding Corporation showed a possibility of obtaining additional products having weight content of metal which is profitable for consequent metallurgical processing and purification of waters to comply with quality standards. A possibility of transformation of technological chain depending on season variability of water quality is put behind the designed technological schemes.

Jan 1, 2018

By D. L. Koch, J. W. Tester, L. K. Sinclair

"In this study, hydraulic conductivity (K) geostatistics were used to predict residence time distribution of well-to-well flow. Flow profiles, fracture density measurements, and pumping tests were available from the highly fractured Florence Copper in situ leaching site. The flow profiles were used to establish the statistical distribution and spatial autocorrelation of K. Two tests were used for validation. The first test confirmed that fracture density and K are autocorrelated over similar length scales. In the second test, Monte Carlo flow simulations successfully recreated the results of pumping tests. Flow sim¬ulations were used to stochastically model well-to-well residence time distribution. RÉSUMÉ Dans cette étude, nous utilisons la géostatistique de la conductivité hydraulique (K) pour prévoir la distribution des temps de séjour (DTS) de l’écoulement entre les puits. Des profils de l’écoulement, des mesures de la densité des fractures et des essais de pompage existaient pour le site fortement fracturé de lixiviation in situ de Florence Copper. Les profils de l’écoulement ont permis d’établir la distribution statistique et l’autocorrélation spatiale de K. Deux essais ont servi à la validation ; le premier a confirmé que la densité des fractures et K sont autocorrélés sur des échelles de longueur similaires ; quant au second, des simulations d’écoulements de type Monte Carlo sont parvenues à reproduire les résultats des essais de pompage. Les simulations d’écoulement ont servi à établir un modèle stochastique de la DTS de l’écoulement entre les puits.INTRODUCTION In situ leaching is the circulation of a dilute acid or base solution in the subsurface, via a series of injection and recovery wells, to dissolve a target metal. In situ leach modelling requires forecasting the residence time distribution (RTD) of flow between wells. In fractured formations such as copper porphyry deposits, order-of-magnitude variations in hydraulic conductivity (K) can result in highly channeled flow, resulting in a heavy tailed RTD (Becker & Shapiro, 2003; Kang, Le Borgne, Dentz, Bour, & Juanes, 2015). Channeling through preferential pathways has impacted copper recovery at several past in situ leaching field tests (Cathles, Glenn, Lenzi, Nigrini, Deans, & Huff, 1978; Ahlness & Pojar, 1983; Schmidt, Earley, & Friedel, 1994; Sinclair & Thompson, 2015). The aim of this work is to combine multiple types of hydrogeological measurements to stochastically forecast the well-to-well RTD in fractured rock for the purposes of copper in situ leach modelling."

Jan 1, 2018

By A. Morrison, D. Mesa, P. R. Brito-Parada

"Froth flotation is the most widely used mineral separation technique. It is based on the relative hydrophobicity of valuable and gangue particles. In a flotation tank, two distinct zones can be identified: the pulp and the froth. The pulp is a turbulent region in which hydrophobic valuable particles attach to air bubbles while hydrophilic gangue particles remain in the slurry. As the particle-laden bubbles rise, a mineralised froth zone is formed that overflows as a concentrate. Although the process is more than a hundred years old, there remain many aspects that are not completely understood, particularly for the froth zone. Thus, the rules governing the design of flotation tanks tend to focus on pulp zone parameters, which are largely based on operating data. An example of this is the design and operation of impellers. These tend to be designed paying attention to hydrodynamic phenomena in the pulp zone, but their effect on the froth zone has not been completely addressed. The role of impellers in a flotation tank is to break the air bubbles in order to generate smaller ones and to provide an environment that enables the collision between those bubbles and the particles in the slurry. This usually creates turbulent regimes that can affect the pulp-froth interface, destabilising the lower regions of the froth and affecting the overall performance of the process. Different impeller designs and retrofit modifications have been proposed in the past, addressing some of those issues. However, there is no systematic study of the effect of different impeller designs on the bubble size in the pulp and its links to the stability of the froth. This work tested the impact of an impeller designs combined with the use of a stator on the performance of an 87 litres continuously operated laboratory-scale flotation tank, with a focus on bubble size in the pulp and froth stability. The results showed that the implementation of a stator system decreased bubble size and increased froth stability. That resulted in an increase of mass pull, measured as a proxy of metallurgical recovery."

Jan 1, 2018

By Bent Babel, Martin Rudolph

"The characterization of reagent-mineral interactions in flotation systems of finely intergrown ores holds difficult challenges for the applicability of standard techniques like Hallimond tube tests and contact angle experiments or renders them impossible due to a lack of sufficient samples in terms of quality and quantity. This disadvantage may not apply to more sophisticated techniques, but these often do not work in an aqueous environment. We present the utilization of an atomic force microscope with a hydrophobic colloidal probe to characterize the wettabilities of individual mineral domains of an ore sample, while additional spectral information is gathered by Raman spectroscopy. The exemplary ore sample investigated is mainly containing cassiterite and quartz, therefore the reference measurements like Hallimond tube tests and contact angle experiments were carried out with this binary system as a comparison. The focus of the study lies in the correlation of data gathered by the atomic force microscope and the Raman spectrometer with data from standard techniques. Finally, the applicability of the colloidal probe atomic force microcopy technique for reagent-mineral investigations is critically evaluated.INTRODUCTIONThe focus of this paper is the application of colloidal probe atomic force microscopy (CP-AFM) for theinvestigation of reagent-mineral interactions on a binary system of cassiterite and quartz. This and similar concepts using hydrophobic AFM probes have been applied by multiple authors (Rudolph and Peuker, 2014a; Rudolph and Peuker, 2014b; Wada et al., 2017; Xie et al., 2017). The hydrophobic interaction is the main interacting mechanism for the hydrophobic colloidal probe with hydrophobic sample surfaces and the long range attractive component has been accounted to nanobubbles on the interacting surfaces (Yakubov et al., 2000). More detailed information on nanobubbles are available in two reviews compiled by Attard and Hampton (Attard, 2003; Hampton and Nguyen, 2010). This paper is based on the work by Rudolph and Peuker comparing different AFM based measuring concepts, additionally gathering data with Raman spectroscopy and correlating results of microflotation and CPAFM measurements (Rudolph and Peuker, 2014a; Rudolph and Peuker, 2014b)."

Jan 1, 2018

By John O. Marsden

"Technology development and innovation has played a crucial role in the copper industry throughout history. The effective development and implementation of new technologies allows mankind to produce copper at progressively lower cost of production at a given feed grade and mineral type. This progress serves to counteract cost inflation/escalation over time and, depending on the magnitude of the cost benefit, allows ore cut off grades to be reduced thereby improving the availability, accessibility and utilization of resources. Two broad categories of technology development and innovation play a key role in this process: (i) incremental improvements and optimization of existing technology provide benefits in the near- to medium-term, and (ii) step change technologies provide value over the longer term. A key issue for potential developers and implementers of new step change technology is how to justify resource allocation and expenditures for such initiatives. This paper examines this issue with reference to specific case studies in the copper industry. INTRODUCTION AND BACKGROUND Technology development and innovation has played a crucial role in the commodity minerals industry throughout history, and none more important than the copper industry. As new, cost-efficient technologies are commercialized, the cost of production in real terms at a given ore feed grade and mineral type decreases. This progress enables ore cut off grades to be reduced allowing lower grade material to be processed economically, which in turn increases the availability and supply of the metal or mineral of interest. Cost inflation/escalation works in the opposite direction, squeezing margins for operations utilizing incumbent technology to process material from a given ore deposit. A prior review by the author considered the issue of technology development and sustainable competitive advantage. This review concluded that first movers and fast followers can achieve competitive advantage for periods of 10-15 years through effective deployment of new technologies (Marsden, 2004). A new, more comprehensive study and evaluation was completed in 2014. This paper presents a portion of the results from the 2014 study."

Jan 1, 2018

By G. Bulut, Ü. Yenial

"Heavy metals contamination in aqueous systems can be found in a variety of industries, in particularly mining, metal processing, finishing and plating. Water containing more than 0.5 ppm heavy metal considered as a toxic due to harmful effects on health. The major techniques employed for heavy metal removal from industrial wastewaters include precipitation, reduction, ion-exchange, and adsorption. Adsorption is a heavy metal removal method for aqueous systems. As a common adsorbent, activated carbon has been used in treatment but it is ineffective on some elements. Thus, there has been a research for developing highly effective and selective adsorbents. In this study the adsorption of lead and arsenic ions on to coal waste and red mud waste was studied. The experimental parameters were determined as pH, equilibrium time and the initial concentrations, activation by heat treatment and the blend of adsorbents. According to their adsorption capabilities, red mud was found to adsorb lead and arsenic ion with high efficiency but coal waste did not adsorb arsenic ion. However the binary adsorptions of these ions were enhanced the adsorption efficiencies. In addition the blend of coal waste and red mud affected the adsorption efficiency. INTRODUCTION As a result of rapidly developing industry and excessive use of water resources, the need of clean water and wastewater management appear as a problem. Wastewater recycling activities and researches come to the fore for an effective use of wastewater. Recycling of wastewater, which contains heavy metals harmful to the environment and human, is a difficult process. Heavy metals are generally divided into three categories: toxic metals, precious metals, radionuclides. Wastewaters from various industries, containing heavy metals, are the main polluters of water and soil. Although their toxic structures, heavy metals are used extensively in industry as they have technological significance. Usually mining industry, metal industry and industrial organizations produce heavy metal containing wastewaters (Volesky 1990, Ting and Lawson 1991, Bishop 2002)."

Jan 1, 2018

By A. V. Kanarskay?

The research is aimed at involving in the processing of poor platinummetal natural and technogenic raw materials. The purpose of the research is the creation of a multifactorial complex of innovations in the system of ore preparation and separation cycles, which ensure a high efficiency of flotation enrichment of hard-to-treat raw materials. In the usual practice of enrichment, minerals of the platinum group (PGM) of less than 10 microns in size are the source of inevitable process losses. For poor raw materials, it is precisely thin PGMs that are characteristic, their proportion sometimes being almost 100%, and their opening leads to the formation of a large amount of slime, which adversely affects the efficiency of flotation. To reduce the yield of slimes and increase the selectivity degree of the opening of the PGM in the ore preparation cycle, a dry grinding scheme and pneumoclassification of the milling material has been developed to obtain fractions of different fineness, density and morphology of the particles. From 2 to 5-fold reduction in the yield of slurries for various ores has been achieved. The separation cycle successfully tested are: flotation of fractions in separate cycles with a differentiated choice of the reagent regime; preliminary selective flocculation of slime fraction material; use of a new generation of bioreagents for flocculation and flotation. A new approach to subsoil research is protected by a patent. The dependence of the efficiency of biocollectors on the composition of biomineral extract from the processed raw materials, which forms the basis of new reagents, is established. The possibility of obtaining the degree of extraction of PGM, native gold and sulphides from finely ground pre-fractionated poor ores with the use of biocollectors of at least 85% is proved. With conventional reagents, the extraction of PGM is 12-23% lower, with the use of traditional ore-preparation apparatuses, the PGM recovery rate was halved. Methods for the long-term storage and preparation in industrial conditions of biocollector reagents that do not require the purification of waste waters from them have been developed. The developed multifactorial system of intensification of flotation enrichment can be introduced to recovery PGM from tailings of enrichment of titanomagnetite, chromite and copper-nickel ores.

Jan 1, 2018

By M. F. Gallerneault, V. Fallah, A. Howells, W. M. T. Gallerneault

"The occurrence of recrystallization in cold-worked aluminum sheet during the brazing process leads to loss of strength, an inhomogeneous grain structure and reduced corrosion resistance. AlMgScZr alloys are known for their extraordinary recrystallization resistance due to the influence of Sc and Zr addition on their microstructure. Here, we investigate the effect of alloy composition (i.e. Mn, Mg, Sc, Zr content), cold-roll reduction and pre-aging treatment on the recrystallization behavior of cold-rolled sheets at brazing temperatures typically used during the manufacture of heat exchanger units. The analysis of recrystallization behavior is carried out through microstructural characterization and the results are compared with the behavior of a commercial, AA3xxx-based heat exchanger alloy.INTRODUCTION Control of recrystallization is of critical importance during brazing, which is a widely-used joining technique for aluminum alloys in aircraft structures (Heinz, 2000) and automotive heat exchangers (Miller, 2000; Marshall, 1993). Due to excessive local heat at brazing temperatures, the cold work texture of aluminum alloys in the cold-rolled sheets may undergo a local recrystallization process (Marshall, 1993). This leads to the formation of an inhomogeneous microstructure and thus anisotropic mechanical properties (Miller, 2000) and low corrosion resistance (Marshall, 1993) across the sheet. X800, a commonly-used Al-Mn alloy series for automotive heat exchangers applications, has been developed specifically for a higher strength as well as an enhanced corrosion resistance as opposed to the traditionally-used AA3003 alloy (Marshall, 1993). X800 alloys, however, exhibit a low recrystallization resistance at normal brazing temperatures, i.e. 590°C. In contrast, Al-Sc-Zr alloys have been shown to exhibit an extraordinary recrystallization resistance at such temperatures (Riddle, 2004) while also being corrosion resistant and possessing a high room-temperature strength (Fuller, 2002). This has been shown to be due to the formation of coherent, nanoscale Al3(ScZr) precipitates that effectively impede grain boundaries while also exhibiting very slow coarsening kinetics at high temperatures (Riddle, 2004; Jones, 2003; Ocenasek, 2001). In this study, we analyze the recrystallization behavior of X800 alloys under brazing conditions through introducing Sc and Zr into the system as well as varying the Mn and Mg content. The effect of processing route is also studied by introducing a pre-aging stabilization treatment as well as varying the cold-roll reduction prior to the final brazing anneal."

Jan 1, 2018

By Peng Cao, Jimin Su, Yang Li

"Abutment pressure distribution is different when a longwall panel is passing through the abandoned gateroads in a damaged coal seam. According to the geological conditon of panel E13103 in Cuijiazhai Coal Mine in China theoretical analysis and finite element numerical simulation were used to determine the front pressure distribution characteristics when the longwall face is 70 m, 50 m, 30 m, 20 m, 10 m, and 5 m from the abandoned gateroads. The research results show that the influence range of abutment pressure is 40 m to 45 m outby the face, and the peak value of front abutment pressure is related to the distance between the face and abandoned gateroads. When the distance between the longwall face and abandoned gateroads is reduced from 50 m to 10 m, the front abutment pressure peak value kept increasing.When the distance is 10 m, it has reached the maximum. The peak value is located in 5 to 6 m outby the faceline. When the distance between the longwall face and abandoned gateroads is reduced from10 m to 5 m, the front abutment pressure sharply decreases, the intact coal yields and is even in plastic state. The peak value transfers to the other side of the abandoned gateroads. The research results provide a theoretical basis for determining the advance support distance of two gateroads in the panel and the reinforcement for face stability when the longwall face is passing through the abandoned gateroads.INTRODUCTIONFront abutment pressure is the result of rearrangement of in situ rock stress caused by the mining (removal) of the coal seam. Research on the distribution character of face abutment pressure have significant importance in confirming the width of the coal pillar and the distance of advance support in roadways (Liu et al., 2011; Liu, Jiang, and Zhu, 2015). Currently, there is a lot of research on abutment pressure characteristics of traditional longwall coal faces, thick coal seam longwall faces, isolated faces, and extra wide face abutment pressure distribution (Xie et al., 2006). However, theoretical analysis and research on the distribution law of the fully mechanized coal face to abandoned gateroads are relatively less. Abandoned roadways are often from less mechanized or room and pillar mines. Due to the existence of these roadways pre-longwall mining, the in situ stress has already been redistributed around the roadway (Liu et al., 2007). Thus, when the longwall approaches and mines through the roadway, the abutment pressure distribution behaviour has different characteristics than those of traditional solid undisturbed coal. Especially when the face approaches the abandoned roadway, the understanding of face abutment pressure distribution has significant importance to the timing of support installation (Ren and Ning, 2014). This prevents the occurrence of a roof and rib failure ahead of and on the longwall and highly efficient advance of the longwall safely and productivity. This paper analyses the E13103 face of the Cuijiazhai Mine of Wenzhou Mining Co., Ltd of Kailuan Group, as the engineering case study, and uses FLAC3D numerical simulation software to conduct numerical simulated analysis on the abutment pressure distribution mechanism of longwall coal mining face."

Jan 1, 2018

By K. Price, G. Wang, L. R. Moore, Y. R. Xiong, J. Gu

"Sand is a naturally occurring granular material that is a result of the physical or chemical breakdown of rocks. Raw/natural sand contains various minerals, and it is this combination of minerals that brings the value to the construction aggregate industry. However, it is the quartz component of sand that is valued in its application as industrial silica in glass, high purity quartz, foundry sand, and oil and gas fracturing. Depending on the industry, the grade requirements can be the concentration of SiO2, particle size or shape, as well as contaminants such as the heavy refractory minerals, clays, fines, and alkali metals. With the ever declining mineral feed grade, processors continue to face challenges making the industry specific concentrate grade. As such, it becomes more important to tailor make the processing reagents to fit the mineral, processing conditions, and desired quality specification. This paper focuses on the application of novel collectors towards the beneficiation of sand for each of the major industrial silica applications. INTRODUCTIONQuartz is a mineral composed of a framework of silicon and oxygen atoms. It is the second most abundant mineral in the Earth’s continental crust. There are many species of quartz, which are defined by the particle size, shape, and color. Silica sand is one of those species, which is the byproduct of the physical or chemical breakdown of quartz containing rocks or crystals. Geologist define silica sand as a silica mineral with a particle size between 0.05 and 2 mm in diameter (Zdunczyk, 2001). Silica sand has significant value to society in recreation (beach sand and toy boxes), construction aggregate (concretes and asphalt), industry (iron & steel casting, fracturing proppants, and glass), as well as specialty products such as semiconductors or silicon wafers used in electronics.The aggregate business is the dominant consumer of silica sand products. Conversely, glass making, foundries (casting material), abrasives, and fracturing proppants are the dominant applications for industrial silica sand. Not much beneficiation is required for sand products going into the construction industry, other than sizing and scrubbing to remove clay. However, the industrial silica sand applications are dependent on particle size, shape, and degree of contaminants, which sets the market value (table 1). Therefore, as the more specialty products are produced, more sophisticated techniques and chemistry need to be applied to ensure the appropriate quality is met."

Jan 1, 2018

By R. Fernando

"The National Institute for Occupational Safety and Health (NIOSH) National Personal Protective Technology Laboratory (NPPTL) is leading an effort to develop the next generation of self-escape breathing apparatus for egress from confined spaces in emergency scenarios. A backpack style closed-circuit mine escape respirator design was one configuration explored as part of the research imperative directed by the 2006 MINER Act. Stakeholder feedback from MSHA and at the NIOSH Breathing Air Supply Partnership Meeting indicated a smaller belt worn unit that does not sacrifice performance is desirable. This paper outlines some further technology advancements that may be investigated toward developing such a small-sized respirator. Technologies being considered are novel chemicals for improved carbon dioxide (CO2) absorption and oxygen (O2) production, eliminating a dedicated CO2 scrubber by incorporating its function in the spaces of the respirator’s breathing loop and storing O2 in a liquid form with long standby capabilities. When these technologies are applied to a future design, there is the possibility of having an escape respirator that can be belt worn and capable of being certified to 42 Code of Federal Regulations (CFR) Part 84 standards, including sub-part O for escape purposes including mine escape. BACKGROUND NIOSH NPPTL has a Research and Development effort to provide mine workers with state-of-the-art breathing air technologies to comprehensively support initial and continued self-escape, refuge alternatives, and rescue needs, resulting from mine emergencies. As part of this R&D effort, NIOSH invested in the development of a next-generation closed-circuit mine escape respirator (CCMER) which would be compliant with NIOSH’s respirator standard requirements, 42 Code of Federal Regulations Part 84, including sub-part O. The design features of the CCMER also address the MINER Act’s requirements for transitioning between devices without the need for doffing the initially donned device. It would also allow for improved protection when using voice communications with a donned device ."

Jan 1, 2018

By J. L. Nebreda, Z. Fan, J. B. Patel

"A380 alloy has been widely employed to produce thin-wall components via high pressure die casting (HPDC). During HPDC processing, there is a significant problem of property variation even with the very stable and precision automated casting procedure. The enlarged variation lowers the component performance and affects the steady and uniform property distribution along the whole component. In this study, high shear melt conditioning technology was developed and applied to the melt prior to pouring into the shot sleeve. Experimental results show that with application of intensive melt shearing, the variation of elongation was decreased from 21.8to 13.9%, and yield strength variation was reduced from5.5to 3.6%. The improved property variation is attributed to enhanced nucleation both in shot sleeve and the die-cavity, and to the improved distribution of porosity and secondary phases as a benefit of high shear induced grain refinement. With application of high shear, large number of the Spinel phase (MgAl2O4) particles with double size distribution in average diameter of 80and 300nm were formed. Due to the good orientation relationship and small misfit between alpha Al and MgAl2O4, the particles act as the effective nuclei in shot sleeve and die cavity, respectively.INTRODUCTIONA380 alloy had been widely used for produce automotive components by cold chamber high pressure die casting(HPDC) processing, due to its relative good mechanical properties and cast ability performance, and more important most of A380 ingots were produced by recycled Al alloys. Therefore, to promote utility of A380 will contribute to reducing emission of CO2and to the lightweight of automotive industry as well. When cold chamber HPDC was employed to produce the components, the mechanical properties of A380 alloy always have a distribution range (named variation herein), or in other words the properties were not stable. The reason was ascribed to the typical solidification characteristics occurred in HPDC processing. During HPDC processing, there are three steps of melt movement. The first step is that the melt was poured into shot sleeve at temperature of about 680°C, in which shot sleeve was preheated by few shots of melt filling, or by heater. During step one, the first solidification of melt was happened in shot sleeve and about 20% solid made of coarse a-Al grains was formed(Li, Xiong, & Guo, 2016).Such kind of grains will retain in the final products and deteriorate the properties variation. The second step is that the melt was forced moving forward slowly by plunger at about 0.2–0.3m/s until the liquid melt front to the inner gate of mold. The third step is that the melt moved very fast to complete the filling of die cavity and refilling the solidification shrinkage by fast movement of plunger about 2–3m/s. The second solidification was occurred in die cavity and fine a-Al grains will be formed by high cooling rate at about 500–1000°C/s. From the solidification point of view, the grain size was dominated by nucleation and growth. When HPDC was employed to produce components, the melt quality becomes the priority factor to control the solidification process as the other casting parameters were kept at the same."

Jan 1, 2018

By S. F. Kaplan, A. S. Dolotov, V. N. Kovalev

"The proportion of refractory sulphide ores and concentrates in world gold mining industry is growing every year. Pressure oxidation of these materials (in autoclave) allows to oxidize gold hosting minerals. Traces of halides and pseudohalides present in the slurry liquids contribute to formation of complex gold compounds. Sorption-active carbon present in ores leads to irreversible adsorption of complex gold compounds and their loss. The objective of the research is to study gold extraction dependence on the concentration of chloride-, cyanide- and thiocyanate-ions in the slurry liquids during pressure oxidation. Double refractory flotation concentrate of the Bakyrchik deposit was used for the testwork. The research was planned on the basis of a full factorial experimental design with additional refining experiments. Ligand concentrations (0 – 1000 mg/l Cl-, 0 – 600 mg/l CN-, 0 – 1200 mg/l of SCN-), temperature (200 – 240 °?) and retention time (1 – 6 h) were used as variables of pressure oxidation process. It was determined that sulfide minerals oxidize much faster than ""organic"" carbon. Under the conditions of T = 240 ?C, t = 2 h, sulphide sulfur oxidation was 95.6%, while ""organic"" carbon oxidation was 46.1 %. Each of the examined ligands has a significant adverse impact on gold extraction. Analysis of the experimental data demonstrated that with a high degree of confidence (R2 = 0.883) gold extraction does not depend on the ligand type, but only on its concentration and the ""organic"" carbon oxidation degree. In case of complete oxidation of ""organic"" carbon, the presence of the ligand (L = Cl-, CNS-, CN-) in the liquids at a concentration of up to 20 millimole/L does not significantly affect gold extraction. The assumption that the main factor of preg-robbing in ???-CIL treatment of double refractory concentrates is the natural ""organic"" carbon sorption-active to gold has been confirmed. INTRODUCTION In recent decades, placer gold mining has been gradually declining and hardrock gold mining, including ""refractory"" gold mining, has been growing all over the world, as well as in the Russian Federation (http://www.miningworld.ru, 2015). One of the main reasons why gold ores are refractory is gold adsorption on natural carbonaceous materials (""organic carbon""). Only a few technologies are suitable for processing such ore concentrates (a significant amount of gold is contained in refractory hardrock ore both in Russia and worldwide) (Vorob'yev-Desyatovskiy N.V., Yepifanov A.V., 2014)."

Jan 1, 2018

By G. Mucsi, F. Kristály, Á. Rácz, É. Gregus, K. Bohács

"Stirred media mills are widely used in the industry for fine grinding. Most of the applications work in wet mode, however dry grinding in stirred media mill comes forward more frequently nowadays. The present paper deals with the differences and similarities of the wet and dry grinding in stirred media mill from energetic and mechanochemical point of view as well. Grinding experiments in batch stirred media mill were carried out with different materials. During the experiments zeolite and kaolin were used as feed material. The grinding experiments were carried out at different stress energy and stress number values; the grinding work was measured during milling. After grinding X-ray diffraction (XRD), Fourier Transform Infrared Spectroscopy (FTIR), particles size analyzes by laser scattering were carried out on the ground materials. As a result of the systematic grinding and analytical measurements a comprehensive comparison was carried out on the wet and dry grinding and their usefulness for mechanical activation in stirred media mill. INTRODUCTION The natural zeolites are crystalline hydrated aluminosilicates of alkali and alkaline earth characterized by the structure that contains frameworks responsible for the high cation exchange capacity (CEC) and absorption capacity. The frameworks are interconnected by cavities and resided by cations variable in size, coordinated by water molecules. Since zeolite comprises SiO4 and AlO4 tetrahedra interlocked by oxygen atoms that are situated in the structural nodes, their characteristics differ due to the varieties in the structure-directing agents and Si/Al ratio (Colella and Wise, 2014; Malekian et al., 2011; Terzic et al., 2017). The most common natural zeolite occurring in high amount, of industrial importance and involved in milling and MA is the clinoptilolite, in the literature equivalent to “natural zeolite” designated for high clinoptilolite bearing volcanic tuffs. Its amount in the host rock must reach ~ 40 % by weight to obtain the CEC and adsorption desired in its applications. In the highest quality rock might reach 80-90 % by weight (Favvas et al., 2016), but most often is the 40-60 % by weight content, associated with smectites, improving the CEC and adsorption of the tuffaceous rock. The application of such natural zeolites is problematic in many cases due to high silica (quartz, cristobalite and volcanic glass) content and beneficiation (concentration and extraction of pure zeolite) are not feasible. Thus, mechanical activation is a possible way to alter the other than clinoptilolite minerals generating high specific surface area and functionalized particle surfaces to enhance adsorption, reaction or particle adhesion. The zeolites easy availability and the utilization cost-effectiveness have prompted the research on their physicochemical and structural properties (e.g. adsorptive and molecular-sieve activity, heat resistance, and microporous cage structure) and finding new options for their application (Kusuma et al., 2013; Musyoka et al., 2014; Rida et al., 2013; Terzic et al., 2015b). Apart from the presence of exchangeable framework cations which are crucial for the adsorption ability, and a certain degree of pozzolanic reactivity. The thermal stability of dehydrated phases is another important characteristic for use of the zeolite in composite materials that are exposed to high temperature. Thereby, the zeolites found a wide application possibility in the design of the construction composites (Albayrak et al., 2007; Najimi et al., 2012; Vejmelková et al., 2015), as well as for resolving of the environmental protection issues like wastewater refining or heavy metal elimination (Gómez-Hortigüela et al., 2014) even from contaminated groundwater using passive methods like permeable reactive barriers (Gombköto et al, 2016). The grinding treatment of zeolite is a common and frequently applied procedure, both on laboratory (Bohács et al. 2017, Faitli and Czél, 2014)"

Jan 1, 2018

By M. Evertsson, M. Johansson

"In minerals processing control is vital to increasing performance and output of a plant. Model predictive control (MPC) is one of the most effective control strategies used in process industry. Sbárbaro (Sbárbaro and Del Villar, 2010), Asbjörnsson (Asbjörnsson, 2015), and Légaré (Légaré et al., 2016) have for example highlighted the possibility to simulate, develop and tune control systems using plant simulators within minerals processing. In more recent years the use of model predictive controllers have increased, and many process industries now utilize more advanced control methods to regulate their processes, raising the question regarding how to, build, test and verify a proposed control solution successfully. In this research, a linear model predictive controller is formulated and applied to a simulator of an existing tertiary crushing circuit. The circuit has in previous work by Johansson (Johansson, 2017) been modeled in MATLAB Simulink and calibrated relative plant data to an average error of less than 10% over 8 hours of production. The work demonstrates how to formulate the controller model structure to describe conveyor belts, storage components, screens, crushers, and control objectives for a minerals processing circuit. The work illustrates how to apply and successfully evaluate possible upsides in a circuit. The advantage of a crushing circuit simulator is that it can be configured, tuned and modified in any possible way, which is of great benefit to developers and engineers. Additionally, examples of how to use estimated measures to improve the performance of the plant are demonstrated. The control performance is finally evaluated for three different controller configurations."

Jan 1, 2018

By Thi Hien Tran, Huy Hoan Nguyen, Thi Thu Hien-Dinh, Hong Son Nguyen, Duy Anh Dao

"Lithium discovered in La Vi deposit, Quang Ngai province in the Central of Vietnam was estimated with a reserve of approximately 1.5 million tones of lithium ore, which was characterized by mainly lepidolite with muscovite, albite, and quartz. This study investigated reasonable flowsheet and optimal conditions of enrichment technology for lepidolite from the mined ore by flotation process, and producing Li2CO3 and LiCl from lepidolite concentrate by hydrometallurgical process. The significant conditions for froth flotation of lithium ore including particle size, pH of ore slurry, pulp density, chemical spending (collectors, activators, depressants, and frothers), stirring and flotation time were investigated. The identified reasonable flowsheet and optimal conditions for froth flotation the La Vi lithium ore processed lepidolite concentrate containing up to 4 wt.% Li2O with a recovery of 87.61 wt.%. The processes of sulfation roasting lepidolite concentrate using FeSO4.7H2O, then leaching in H2SO4 solution, and removing impurities were carried out to prepare a pure lithium-bearing solution for producing Li2CO3 and LiCl. The products containing 99.05 wt.% of Li2CO3 and 99.02 wt.% of LiCl were obtained with recoveries of 82.97 wt.% and 85.77 wt.%, respectively. The obtained results indicated that lithium ore in La Vi deposit can be processed to produce commercial lithium products and lead the study to develop technology for a new industry of lithium processing in Vietnam.INTRODUCTION Lithium is the lightest metal, which has many superior properties in both metal and compound (such as Li2CO3, LiCl...) states since its discovery in 1817 by Swedish chemist Johan August Arfwedson. Lithium is a favourable material for many high technology fields such as aerospace industry and chemical industry. Some industrial fields which present the main consumptions of lithium include ceramic, glass, aluminum alloy, lubricants, rechargeable Li-ion batteries, synthetic rubber, and pharmaceuticals. The worldwide production of lithium in 2014 was 31,700 tones, continually increased in 2015 of 5% presented 32,500 tones (USGS, 2016). The demand for lithium tends to increase because of the raising in consumption of lithium batteries. Lithium is mined from salar brines, mainly in Chile and Bolivia, but also from granites and pegmatites, which contain minerals with high lithium content such as spodumene - LiAlSi2O6 (Heinrich et al., 1978; Linnen et al., 2012); petalite - LiAlSi4O10 (Sitando & Crouse, 2012); zinnwaldite - KLiFe2+Al(AlSi3O10)(F,OH)2 (Paukov et al., 2010; Kondás J. & Jandová J., 2006); lepidolite - K(Li,Al)3(Si,Al)4O10(F,OH)2 (Luong et al., 2013); and amblygonite - LiAlPO4F (Garrett, 2004)."

Jan 1, 2018