Search Documents

By Peng Qian, Xiao Li, Guoyan Fu, Peiwei Han, Yongliang Wang, Shufeng Ye

"Arsenic removal from high arsenic gold concentrate is conducive to increase the mineral value and realize the mineral comprehensive utilization. This study investigated the alkaline pressure oxidation leaching (APOL) of an arsenical gold concentrate in lower temperature to separate the arsenic into filtrate. The effects of temperature, NaOH concentration, solid-liquid ratio, reaction pressure and stirring speed on the leaching efficiency were investigated, and the characteristics of the gold concentrate and leaching residues were evaluated using XRD and SEM analysis methods. The obtained results showed that by using lower temperature (<60?) it is possible to avoid the production of elemental sulfur during the leaching process, which is benefit for the oxidation of arsenopyrite; When the reaction was carried out under appropriate conditions, more than 98% of the arsenic will be extracted into the filtrate as the form of arsenate or thioarsenate. INTRODUCTION In recent years, there has been considerable interest in the recovery of gold from refractory arsenical gold ore. The arsenic in this kind of ore usually exists as the form of arsenopyrite, and the gold surrounded by arsenopyrite exists as the form of fine particles, which will give many difficulties to metallurgical work. When the content of arsenic in the gold ore is more than 0.5%, it will seriously penalize the smelting efficiency (Ruiz et al., 2014). So pretreatment of the refractory gold ore is necessary to obtain the largest economic value and environmental benefits (Balaz et al., 2000). The oxidation pretreatment processes mainly include roasting oxidation, pressure oxidation, chemical treatment and biological treatment (Ann et al., 1992; Kou and Chen, 2012; Tongamp et al., 2010; Fernandez et al., 1995; Lin and Zheng, 1996). Among them, the roasting oxidation and pressure oxidation are the more ordinary processes in industry. The roasting oxidation process is the mature and adaptable technology, but the production of waste gas containing sulfur and arsenic will pollute the environment. The pressure oxidation method possesses certain metallurgical and environmental advantages, and can efficiently decompose the mineral. According to the different solution media, the pretreatment can be divided into alkaline and acidic pressure leaching pretreatments (Papangelakis and Demopoulos, 1990; Hiskey and Sanchez, 1995). The acidic pressure oxidation method has been used in most smelting plants for high arsenic gold ore pretreatment, while the alkaline pressure oxidation is still not widely applied. Compared with the acidic pressure oxidation, the alkaline pressure oxidation can be realized under lower temperatures."

Jan 1, 2018

By K. C. Corin, M. S. Manono, R. M. Manenzhe, J. G. Wiese

"Environmental concerns necessitate the recycling of process water within mining operations. Given that recycled water is chemically different from fresh water, and collectors are added such that they adsorb at the liquid-particle interface, changes in the aqueous phase are expected to affect collector adsorption. A Finnish nickel-copper ore was floated in synthetic plant waters of varying ionic strengths and plant waters obtained at Boliden Kevitsa Mine, with aerophine and sodium isopropyl xanthate as collectors. Of the tested waters, the copper thickener overflow was the least conducive to xanthate adsorption and valuable mineral recovery. The nickel thickener overflow, standard process water, and raw water were the most conducive to xanthate adsorption. For the raw water and nickel thickener overflow, increased adsorption correlated with increased valuable mineral recovery. Further, recycling xanthate retained in water affected the selectivity of the collector and hence the concentrate grades.INTRODUCTIONFlotation is a separation process that exploits the differences in the surface properties of the particles being separated. The efficiency of separation is dependent on the degree of hydrophobicity achieved by the particles meant to be floated, which are, in most cases, valuable minerals. The hydrophobicity is in turn dependent on the adsorption of the chosen collector onto the surfaces of the floated particles (Fuerstenau, 1984; Taggart and Hassialis, 1946). Empirical findings suggest that species dissolved in solution strongly influence collector adsorption and overall flotation response (Fuerstenau and Chander, 1986). Due to environmental concerns, it is becoming more pertinent for mining plants to recycle process water and hence limit the usage of potable water. There is an interest to ensure minimal discharge of plant water into the environment, as this water is typically polluted with process reagents that may render it toxic (Levay et al., 2001)."

Jan 1, 2018

By X. -G. Chen, K. Liu, N. Parson

"Precipitation-strengthening 6xxx alloys are widely used for building and construction and automobile industries due to their high strength, good weldability and corrosion resistance. However, their elevated-temperature properties (250–300°C) decrease rapidly due to the fast-coarsening of precipitates. On the other hand, dispersoid-hardening is one of the most efficient approaches to improve the elevated-temperature properties. Therefore, the evolution of dispersoids during heat treatment in Al-Mg-Si-Mn alloys was investigated in the present work. Various heat treatments with temperatures ranging from 300–500°Cfor up to 24 hours were performed. Electrical conductivity and microhardness were measured while optical and scanning electron microscopy combined with image analysis, were used to characterize the dispersoids. Special emphasis was placed on the evolution of the size and number density of the dispersoids under different heat treatment parameters. It was found that dispersoids started to precipitate at 350°Cfor 1 hour. Nucleation and growth were the main mechanisms at temperatures up to 400°Cwhile coarsening occurred at temperatures above 450°C. The quantitative results indicated that dispersoids precipitation reached the optimum condition after treatment at 400°Cfor 2–4 hours with a fine size and high number density, resulting in the highest hardness.INTRODUCTIONThe precipitation-hardening 6xxx aluminum alloys with major alloying elements of Mg and Si are one of the most widely used aluminum alloys for building and construction and automobile industries (Dinaharan & Murugan, 2012). In recent years, there have been increasing demands for aluminum structural components to be used at elevated temperatures (250–300°C) for different applications. However, the mechanical properties of 6xxx alloys at elevated temperature are typically reduced due to the rapid coarsening of precipitates at 250–300°C. It has been reported that the yield strength (YS) of AA6061 in the peak-aged condition drops from 276 MPa at room temperature to only 30 MPa at 315°C(Kaufman, 1999). Therefore, it is a key concern to improve the elevated-temperature properties of 6xxx alloys to expand their range of applications."

Jan 1, 2018

By X. -G. Chen, J. Qin, K. Liu, D. Racine

"Understanding the thermo-mechanical fatigue (TMF) behavior of materials plays a significant role in the safety design of critical components used in aerospace and automotive industries, such as engine blocks and cylinder heads, which undergo the cyclic change of temperature and stress. However, the cyclic changes of temperature, stress and strain make it difficult using the traditional testing methods to accurately simulate the TMF process. In the present work, the Gleeble® 3800 system was successfully applied to develop a reliable procedure to measure the TMF behavior of aluminum alloys. The modified setup together with the new designed program allows the Gleeble system to precisely simulate the cyclic profiles of temperature and mechanical strain. The novel procedure includes the calibration and verification of the TMF setup to ensure the test validity with Young’s modulus measurement, multi-cycle measurement of the thermal strain and zero stress adjustment followed by online monitoring the TMF cycles. The results of the TMF testing of an AA6061 alloy under cyclic temperatures (60–300°C) and various strain amplitudes (0.2–0.6%) were demonstrated. Its TMF behavior was characterized by the typical hysteresis loops and cyclic stress-strain response.INTRODUCTION The thermo-mechanical fatigue (TMF) behaviour becomes increasing important to evaluate the elevated-temperature properties of materials used as the critical components in automotive and aerospace industries, such as the gas turbines (Hu, Shi & Yang, 2016; Moverare, 2007; Segersäll et al., 2015) and engine blocks (Grieb, Christ & Plege, 2010; Javidani & Larouche, 2014). During the cycles of start-up and shutdown of the engines, these components undergo a complex change of loading. Meanwhile, a dramatic temperature gradient exists on the components due to the cooling system. Therefore, the cyclic changes of load and temperature can give rise to the TMF and may limit the use life of such components (Hu, Shi & Yang, 2016; Javidani & Larouche, 2014; Moverare, 2007). Hence, performing the TMF tests to precisely simulate the cyclic changes of load and temperature to understand the TMF behaviours of materials is playing a significant role in the safety design of these components. For TMF tests, two principal types of cycles are generally employed, including the in-phase (IP) cycle where the load and temperature are at the same phase (i.e. maximum load at highest temperature) and out-of-phase (OP) cycle where the maximum load is applied at minimum temperature (Kliemt, 2012; Miller, 2014). The most significant damage mechanisms in engine components are reported to be OP TMF cycles (Javidani & Larouche, 2014; Kliemt, 2012)."

Jan 1, 2018

By D. B. Mazzinghy, L. C. de R. Machado, H. Delboni, M. G. Bergerman

"The use of vertical stirred mills in the mining industry has increased remarkably over the past few decades, as a result of growing requirement for finer ore grinding. This equipment delivers higher energy efficiency in fine grinding operations when compared to conventional tubular mills. Methods for designing vertical stirred mills involve operational experience, pilot plants and bench tests. An important issue is that these tests require, at a laboratory scale, at least 10–20 kg of material, depending on its density, which is not available in many cases, particularly in the early stages of greenfield projects. For the regrind of flotation concentrates, several bench scale flotation cycles are required to generate such a sample. This paper describes the development of a laboratory jar mill test using a 6”x8” jar – smaller than that commonly used – based on the overall specific energy method, which requires significantly less mass compared with existing tests. The proposed test has proven to be more practical than tests normally used, requiring about a quarter of the mass, and also shows good adherence to industrial results for the studied iron ore processing plant. INTRODUCTION A significant demand for finer grinding has been noticed over the past few decades in several mining projects to achieve the mineral liberation required for the concentration of valuable minerals. However, the finer the product size, the greater the grinding energy consumption, resulting in an overall increase in operating costs, which may reach or even exceed 50% of the mineral processing cost (VIEIRA, PERES, 2013; DANIEL, LEWIS-GREY, 2011). Comminution technology can have a major impact on subsequent ore concentration stages (DANIEL, LEWIS-GREY, 2011; MARSDEN, 2009; NAPIER-MUNN, 2012; PEASE et al., 2010), which further strengthens the importance of proper technology and equipment selection. Adequate grinding circuit selection and design is thus a key aspect associated with mining projects."

Jan 1, 2018

By Chenyang Zhang, Zhigang Yin, Jianyong He, Yuehua Hu

"A lot of floatation reagents (collectors, inhibitors and regulators) for the beneficiation of copper ores have been well developed in the past century. However, it is still unclear about the micro interaction mechanism of these flotation reagents with copper ores. In this paper, the interaction mechanism of these flotation reagents with the copper atom on chalcopyrite has been systematically investigated by first principle DFT (density functional theory) calculations. Thirty-four specific common functional groups linked with the same hydrocarbon chain (ethyl) are optimized at a B3LYP/def2-TZVP level, the solvation effect was included with the SMD solvation model. The analysis of the highest occupied molecular orbital (HOMO), the lowest unoccupied molecular orbital (LUMO) and nature bond orbital (NBO) charge of these reagents reveals their potential applications to other types of copper-bearing mineral. Further investigation of the thermodynamics calculations gives more reliable data to screen collectors or inhibitors for copper-bearing mineral. The flotation results from carefully reviewed literatures are in good agreement with the calculation results. This work might also shed new light on the development and discovery of highly efficient and selective flotation reagents with low cost based on the computational methods.INTRODUCTION Froth flotation,(Shean & Cilliers, 2011) a mineral processing approach, is applied to efficiently enrich valuable minerals from the mixture, which is achieved according to the dictinctive surface properties of minerals. In the past century, researchers have develped an aboundant of flotation reagents by extraction or synthetize, and many carefully selected reagents might die in the bench tests or the pilot tests before the pratice.(Bulatovic & SrdjanM, 2007) Generally, it involves a lot of cost and tedious works by conducting flotation tests to screen flotation reagents. Flotation reagents have been boomed robustly with the developing of the organic synthesis.(Liu, Yang, & Zhong, 2017) Reseachers found the specific properties of a reagent are determined by its functional groups and the length of the hydrocarbon, where the functional group is assigned as the adsorption site to adsorb onto mineral surfaces and the hydrocarbon chain is called as a hydrophobic group."

Jan 1, 2018

By I. Gombköto, G. Mucsi, S. Nagy, F. Kristály, Á. Rácz, R. Szabó, B. Egyed

"Present paper deals with the investigation of a Hungarian pumice. Grinding experiments were carried out in a stirred media mill for various residence time. Ground samples were tested with laser particle size analyzer to determine and calculate the material fineness (particle size distribution and specific surface area). The lime adsorption capacity was measured to monitor the reactivity. Alkali activated cement paste was prepared using ground pumice with various alkali activators. Cube shaped specimens were produced from the paste and the uniaxial compressive strength was measured at the age of 7 days. The resulted alkali activated material structure was investigated by XRD and FTIR. The results of the experiments show that pumice fineness has strong impact on its hydraulic activity, hence on the compressive strength and the structure of the resulted binder. Relationships between grinding fineness, material structure and strength of the raw and mechanical activated material as well as the alkali activated cement were revealed. INTRODUCTION Pumice is a natural pozzolan which can be used as raw material for cementitious materials in limited portion owing to its low reactivity. Furthermore, due to its mineralogical composition it can be used for developing a new environmental friendly binder, namely alkali activated cements (AAC) which are inorganic alumina-silicate materials with good cementitious properties (Almalkawi et al., 2017; Özodabas and Yilmaz, 2013; Najimi et al. 2018; Yadollahi et al., 2015). Despite being a rather recent research topic, many papers and books have been published focusing on various aspects of alkali activation. There is great variety of raw materials that can be utilized for AAC production. However, primary raw materials are very expensive and secondary materials are heterogenous in composition. Therefore, a more homogeneous and low price silicate would help to balance the properties and cost of resulting cement and easing the way for commercialization of AAC. However, the control of its reactivity is of great importance which can be realized using mechanical activation by grinding (Juhász and Opoczky, 1990; Djobo et al., 2016; Mádai et al., 2015). The goal of present paper is to investigate the effect of mechanical activation of pumice on the properties of the resulted alkali activated cement."

Jan 1, 2018

By P. V. Malyarov

"This paper examines the grinding and wear processes in drum mills. A summary of the industry’s long-term experience with the proposed linings is presented. A method is proposed for assessing the efficiency of the grinding energy distribution between the successive stages. A case study is presented of grinding energy redistribution at Talnakh Concentrator by replacing spiral classifiers with a drum-type hydraulic screen. The problems of the kinetics of grinding processes in ball mills and semi-autogenous (SAG) mills are examined. It is demonstrated that in ball mills the feed particles are disintegrated by triaxial compression in the mill zones where discrete slippage of the charge occurs at major force interactions between the layers. Mechanism underlying increases in the specific energy consumption in grinding circuits based on SAG mills is shown.The problem of improving the throughput and reducing the specific energy consumption in mineral feed grinding is highly relevant because of the significant energy intensity. Up to 80% of the consumed energy is used to disintegrate ore fed into the drum mill. At all development stages of the drum mill grinding theory, the researchers have paid a great deal of attention to studying the patterns of the charge motion and the kinetics of the feed particles disintegration processes. In [1], it was shown that, due to the slippage between the charge layers being lifted, drum mills at concentrator plants operate in a mixed cascade and waterfall mode. A feature of the mixed mode is the toe zone, where the charge contacts the lining and the transition to a circular path takes place. Studies of the charge motion in the toe zone made it possible to develop a method for designing cross-sectional profiles of lining plates [2] for ball mill drums. The method is based on the principle of interaction between the balls and the lining, where the non-working rear surfaces follow the relative motion path of the balls before impacting the lining, while the working surfaces are orthogonal to the rear ones. Lining with the proposed profile provides contact with the charge and slippage-free transition to a circular path. This ensures an longer service life of the lining, a reduction in specific energy consumption, and an increase in the mill’s feed rate. The proposed method is applicable when designing lining plates of various materials. Steel liners with the proposed profile have been successfully operated [3] for more than 40 years at a number of projects in the industry."

Jan 1, 2018

By H. Staton, N. Michaelson

"INTRODUCTION Lundin Mining’s Eagle Operation, located in Marquette County, upper Michigan consists of a mine and concentrator that process a Ni-Cu-(PGE) ore. The mine itself is an underground operation and the ore is trucked from the Eagle mine site 66 miles to the Humboldt mill where both nickel and copper concentrates are produced. Operations began in 2014 and continued with an average production of approximately 23,000 tonnes of Ni and 20,000 tonnes of Cu per year for the first three years of operation. The Humboldt Mill, currently operated by Lundin Mining, processes the nickel/copper ore from Eagle Mine and performs the concentration through several stages of flotation. Originally built in 1954, the Humboldt Mill began operations as an Iron Ore processing facility, and was converted to a gold processing plant during the 1980s. Various groups owned the site after closure of the gold operation. Eagle purchased the Mill in 2008 and invested more than $280 million to clean up historic mine waste and refurbish the plant (see flowsheet in APPENDIX). This paper will overview the ramp-up of the operation, and discuss some specific areas that went well and some that could have gone better during the design phase. HIGH LEVEL DESIGN CRITERIA Coarse ore arrives from the mine and is stored in a building with a capacity of 10,000 tonnes. Ore is crushed in three stages to a final product size of 100% Passing 12mm. Crushed ore is conveyed to the mass flow fine ore bins, which have a live capacity of 3000 tonnes. Crushed ore is fed to two parallel 900 HP ball mills, charged with 3” high chrome grinding media, and ground, in closed circuit with hydrocyclones, to a p80 of 110 microns in the flotation feed. Soda ash is added to the mills based on process water hardness. Cyclone overflow passes to the bulk conditioner where Sodium Isopropyl Xanthate (SIPX) and Methyl Isobutyl Carbinol (MIBC) are added. The slurry is pumped to the rougher bank for bulk flotation. Rougher concentrate is fed to a 500HP vertically stirred regrind mill and is ground to a p80 of 50 microns, using 5/8” high chrome balls. Rougher tailings report to the tailings thickener. The regrind cyclone overflow is sent to the single stage cleaner bank followed by two scavenger banks. The cleaner concentrate is pumped to the copper-nickel separation circuit. Cleaner tailings report to the tailings thickener. In the copper-nickel separation circuit, the pH is raised to 11.5 and a copper concentrate is recovered from the bulk cleaner concentrate in two stages, namely the copper roughers and the copper cleaner columns. The concentrate from the copper flotation columns is the final copper concentrate. The tailings from the columns return to the head of the copper-nickel separation. The nickel concentrate is the copper rougher tailings stream."

Jan 1, 2018

By V. Sheikhzadeh, M. Saghaeian, R. Hejazi, A. Abazarpoor

"The morphology of pellet feed is known to influence several properties of iron ore pellets, including drop number, compression strength and reduction properties. The effect of grinding method on the particle size, specific surface area and particle shape of an iron ore concentrate has been studied. Grinding methods considered were ball mill and high pressure grinding rolls (HPGR). 5 different samples (Blaine= 1800, 1900, 2000, 2100 and 2200 cm2g-1) were used to compare the size, shape and specific surface of particles for each grinding methods. Particle size was meticulously examined by sieve analysis, laser sizing and image analysis. In samples ground by ball mill, it has been observed that the fraction of particles <10µm increases from 39% to 46% as the Blaine number increases from 1800 to 2200 cm2g-1. For HPGR samples, corresponding figures are 41% and 49% respectively. It is evident that for samples ground by HPGR, the fraction of fine particles is higher than that of those ground in the ball mill. To measure the specific surface area of particles, Blaine and BET were used. A higher real surface area was observed from HPGR treatment in comparison to ball mill grinding, provided by a higher porosity, cracks, roughness and new surfaces. Shape factor of particles was determined using three descriptors: circularity, roughness, and aspect ratio. It was also observed that particles produced by HPGR were more elongated, less circular, and rougher than those processed by the ball mill. 1. INTRODUCTION Particle size and shape are important parameters that can significantly affect mineral processing plants and pelletizing plant performances (Brozek and Surowiak, 2007). It has also been proposed that green pellet quality is directly related to the amount of fine particles in a pelletizing plant (Dwarapudi et al., 2008; Umadevi et al., 2008; Gul et al, 2014; Van der Meer, 2015). Particle size distribution and specific surface area (SSA) are also key factors that can control the quality of green and fired pellets. Processing circuits generally reduce the fines fraction to lower than the required specific surface area (SSA). It is therefore necessary to regrind concentrates to produce suitable pellet feed for further treatment in the balling and firing steps [1, 2]. Two main methods are used for re-grinding of concentrate; high pressure grinding rolls (HPGR) and ball mill. Given the different forces used to reduce size in these methods, it is expected the shape of particles will be different (Pourghahramani and Forssberg, 2005)."

Jan 1, 2018

By G. Dodbiba, T. Fujita, M. Kawata, S. Yamasaki, K. Mitsuhashi, J. Ponou, Y. Iwazaki, T. Atarashi

"The grade of copper ore and concentrate is recently decreasing and it will continues decrease further in the future. The effective liberation treatment for low grade copper ore and the removal of arsenic from copper concentrate is becoming even more important. In this work, the magnetic separation of copper concentrate by heat treatment and the flotation of low grade copper ore by microwave irradiation was studied. The heat treatment of copper minerals in the air atmosphere, the magnetization of most copper minerals increases and especially the magnetization of chalcopyrite shows the largest magnetization, after being heated at 500 oC. The wet HGMS of copper concentrate has been studied and the results have then been compared with the ones when calcined concentrate was used instead. The microwave treatment before ball milling increased the degree of liberation up to 100%, especially when compared with the case when only ball mill was applied to the as-received ore. The flotation of ground copper ore after microwave irradiation showed that the grade copper minerals such as chalcosite and bornite in froth part is much larger than that of tailing part.INTRODUCTION The copper has been used many kind of technological fields and will be more important for the future technology. The global copper production from mine is predicted as shown in Figure 1 (Northey, S. 2014). The copper production peak will be appeared in 2030 and the demand peaks in 2040. In the future the recycling of stocked copper and copper alloy will be necessary to satisfy the demand (Yoshimura, A. 2018). Changes in the grade of copper in copper concentrate, exported from several countries are shown in Figure 2. The copper grade in copper concentrate after mineral processing is gradually decreases every year and it is less than 30% nowadays. On the other hand, the copper ore grade change and prediction are shown in Figure 3. The grade of copper ore is also decreasing to less than 1% in 2010 (Northey, S. 2014). In the future the copper grade gradually decreases, reaching to less than 0.5% in 2080 and the energy to produce the copper metal will increase. The effective liberation treatment for low grade copper ore and the removal of arsenic from copper minerals become more important, nowadays. The microwave irradiation of copper ore for the liberation, energy etc. has been reported by several researchers (for example, Batchelor, A.R. 2017). The magnetization change of copper ore by heating has been reported to remove the arsenic (Sawada, M 2015). In this report, the magnetic separation of copper concentrate by heat treatment and the flotation of copper concentrate by microwave irradiation are discussed after the characteristics of secondary copper minerals are investigated by these treatments."

Jan 1, 2018

By L. Alagha, F. Schott, M. B. Haya, Z. Xiao, K. C. Monyake

"Froth flotation is a process in which valuable minerals are separated from gangue minerals on the basis of surface wettabilities. It is a universally accepted process for the beneficiation of coal. The large amount of coal fines that have been generated from both mining and beneficiation processes has been reported as a chronic problem to both fine coal preparation and utilization as these fines contain a high amount of ash forming minerals. The current study investigated the potential application of Synthetic Bio-compatible Polymers as slime depressants in fine coal flotation for the possibility to enhance the combustible recovery and ash rejection. Raw coal samples containing 21% of ash-forming minerals were crushed, grinded and floated in the presence of Chitosan polymer. Flotation tests were carried out in D-12 Denver flotation cell with 1-Liter capacity. Flotation outcomes were studied as a function of polymer concentration. Box-Behnken factorial method was used for experimental design. Second order response functions were produced for ash% and combustible recovery. The results obtained from this study demonstrated positive influence of chitosan polymer on ash% and combustible recovery. Ash % was decreased by 3.32 % while an increase of 48.15 % in combustible recovery was observed when chitosan was introduced in the flotation process. INTRODUCTION Froth flotation is a widely used method of separating minerals by utilizing the difference between surface wettabilities [1], [2].Modern mechanized mining and ore handling operations produce large amounts of coal fines which in the past were not processed but discarded as waste[3]. Even though flotation is the best method of beneficiation for coal, it can be challenging in case of fine coals. In fine coals, slime coatings of colloidal mineral matter exist on the coal surface. These coatings render the coal hydrophilic, hence reducing flotation efficiency and recovery. Of late, different researches have been using biodegradable polymers to determine their feasibility in enhancing fine coal flotation efficiency[4].Naturally occurring and synthetic polymers, for example, polyacrylamide-based polymers, have been widely used in flotation as multifunctional reagents[5],[6],[7]. Hybrid polyacrylamide polymer has been successfully used as a depressant for ash forming minerals in fine coal flotation[3]. Recently, chitosan has been successfully used in flocculating quartz particles to produce faster settling rates of fine tailings [4]."

Jan 1, 2018

By Anthony Konya, Calvin J. Konya

The publication, RI8507, from the U.S. Bureau of Mines established an envelope equation that related scaled-distance to peak particle velocity in an attempt to predict ground vibration in the design phase of a blast. This has been further modified by Oriard, Dupont, Konya & Konya, and others to develop more refined prediction models for specific situations to obtain better predictions. While these equations can be an ideal starting point for a greenfield blasting project or a project with no given information, these equations can have errors.

Jan 1, 2018

"INTRODUCTION In recent years, there has been increasing focus on environmental and social impacts of the extractive industries, climate change and resource scarcity. The concept of the circular economy aims to replaces the “take-make-dispose” economic model with one that eliminates waste of all kinds and is restorative by design. Such closed-loop systems implicitly aim to reduce the quantity of primary extracted materials entering the economy, thereby affecting supply and demand dynamics, hence mining industry economics. For the metals industry, the ability to engage in, or adapt to the circular economy can be heavily affected by industry structure and geographical factors. Eco-efficiency initiatives that reduce waste and environmental impact may help the mining and metals industry align with some of the goals of the circular economy. This paper focuses on base metals, and explores case studies in copper, lead and zinc. It analyzes primary and secondary metal production, and recycling. It examines company structures and how these affect engagement with the circular economy. CIRCULAR ECONOMY PRINCIPLES Ellen MacArthur Foundation (2012) describes the circular economy as “an industrial system that is restorative or regenerative by intention and design”, which “replaces the ‘end-of-life’ concept with restoration”, and “aims for the elimination of waste through the superior design of materials, products, systems, and, within this, business models”. The concept is systems focused. For materials such as metals, a series of loops are considered, including maintenance of devices, reuse, refurbishment and recycling. Potential methodologies to achieve circular economy outcomes include disassembly and reassembly of manufactured goods, leasing rather than buying major appliances, and converting to renewable energy sources. The circular economy is partially aligned with the principles of eco-efficiency, which relate to reducing the environmental impact per unit of a material produced. PRIMARY AND SECONDARY METAL PRODUCTION Base metals (copper, lead, zinc and nickel) are essential ingredients in modern economies and are key commodities produced by the global mining industry. Metal production can be categorized as primary or secondary. Primary metal comes from the processing, smelting and refining of metal content extracted from ores, while secondary production comes from metals recovered from recycled streams (e.g. recycled lead-acid batteries, copper wire scrap, etc.). Metals are stored in natural, anthropogenic in-use and anthropogenic waste stocks. An example of the stocks, flows and processes associated with global copper extraction and use is shown in Figure 1."

Jan 1, 2018

By D. E. Cameron

"INTRODUCTION Grade control requirements for base and precious metal projects are an important input to both conceptual and feasibility mine plans. It’s the author’s experience that grade control input is insufficient at these critical stages. The few exceptions are a stimulus for this paper. A significant portion of CRC’s practice has involved assisting operations to solve grade control issues which were finally recognized as contributing to negative production variances. Even in operations perceived to be successful, deficiencies in grade control are often masked by measures taken by an operation to compensate a deficiency in one area with outperformance in another. The advantages in having a realistic and adequate grade control plan developed at an early project stage by a geologist(s) with considerable operations experience are manifold. It’s important for the geologist to prepare clear inputs into the mine plan backed by detailed supporting information in usable, flexible formats. When the decision is made to advance a project, the exploration team passes its model to a mine planner. The team doesn’t usually provide a detailed grade control plan with the block model, thus the planner tends to treat grade control as an activity to be rolled into a broader operating category. The consequences of highly compartmentalized mine planning can be severe in the long run. Once a plan is tabled, and especially once production begins, it is very difficult to improve grade control outside the fixed parameters of the operation. Major fixes tend to be costly in terms of time and dollars. Implementing needed changes to the grade control practices and culture in an established mine can present almost insurmountable difficulties. Hypothetical examples of grade control planning are presented to illustrate the author’s points. The diagrams are conceptual and schematic; any resemblance to actual deposits is coincidental. BEYOND 50¢/TON In more than a few cases, grade control cost is buried in a subcategory of mining cost with little more consideration than a plugged number. It is possible to do a word search in 43-101 Technical Reports on advanced projects and without finding reference to “ore control” or “grade control”. The idea is to reach the orebody by the shortest and least expensive means, achieving production and investor payback at the earliest possible occasion. This entails a low stripping ratio pit or a decline ramp with sills on ore to prepare the first stopes. The processes to achieve the target production, one of which is grade control, will fit into this framework. After all, there is a block model and the planner can see the grade and tons in each block. The exploration geologist whose responsibility was to bring a large percentage of the deposit into mineral resource owns the model and has released it to planning. Now comes the planning stage. Mine geologists haven’t been hired yet and they will be phased in with production. What could go wrong? Larger companies may have the geologists with operating depth who will be inserted into the mine planning discussions, but it’s not a given. Junior companies must often delegate the conceptual and detailed planning tasks to consultant groups. Is a senior-level grade control review part of the scope of work for the mine planning? If a good grade control plan is in place before the mine geology team is staffed, a key element of success is assured."

Jan 1, 2018

By J. X. Zhang, F. S. Niu

"In order to accurately detect whether the collision occurs between particle and bubble in flotation process, a collision detection method of particle and bubble, which based on morphological image processing and Otsu method, is presented. First of all, it utilizes image pre-processing to optimize images, the target area and the background area are segmented by Otsu method. Then, particle and bubble are fitted to a circle combined with the least-square method. It’s convenient to obtain the coordinate information and radius. Finally, the position of all particles is extracted to an image, which achieves the particle tracking and avoids the complexity of the continuous frame image tracking.Experimental analysis shows that the relationship between the two ordinate difference d and the bubble radius r has a certain influence on the collision detection when the dripping particles are close to the bubble, when d>r, the detection accuracy is 92%;When d=1/2r, the detection accuracy is 97%;When d=0, the detection accuracy is 100%. The result indicates that this algorithm can detect the collision between particle and bubble quickly, and the working hours of manual test are saved effectively ,the best position of dripping particles close to the bubble which is taken with a CCD camera should be in the range of the particle and bubble’s ordinate difference less than half of the bubble radius.INTRODUCTIONFlotation is an important technical means to separate useful minerals from ores. The flotation process of ores and materials in the world is treated by flotation technology up to billions of tons every year, so the study of flotation process is particularly important. Raising the collision probability between mineral particles and bubbles in flotation process is one of the key factors to improve flotation separation efficiency[1]. The study indicates that[2-4] the collision probability between particles and bubbles is influenced by many factors, such as particle density, particle size bubble size, etc. The analysis of these influential factors requires a lot of experiments. Therefore, it is of great significance to design an accurate collision detection method for the research of this field."

Jan 1, 2018

By Yuliy Rubinstein

"The paper presents a analysis of the history and the trends of development of flotation apparatus. The laws of their evolution are stated and the place and role of column flotation are indicated. It is demonstrate development and different design of column apparatus. The major parameters of column cell such as diameter and height are discussed. Options are proposed on optimization of hydrodynamic characteristics of columns with large-capacity cells. High efficiency of columns with cell height of 4-6 m is shown on examples of coal preparation. A new generation of multi sectional column cells has been developed. In the cells are zones with different aerohydrodynamic parameters: combined in the machine are co-and counter- counter flows of phases. The transition from single-chamber column to multi-sectional apparatus makes it possible to create favourable hydrodynamic and aeration regimes in each section of the column dependent on the pattern of material distribution by floatability. Efficiency of application different designs column apparatus uses shown on the example of enrichment of various non-ferrous metals ores and coal. The principles of mathematical simulation of the flotation process are developed. A scaling-up procedure for column cells was based on flotation macro- and micro- dynamics simulation.INTRODUCTIONColumn flotation is considered to be one of the most significant achievement in the field of mineral processing in the end of last century. We cannot but agree with this statement but would like to understand what underlies this success. History of the flotation column can not be considered in isolation from the development of flotation apparatus on the whole. It can be argued that the first attempt to switch from oil flotation to the use of bubbles during flotation was performed Bessel brothers in 1877 (Berlin patent 42 class 22, July 2) and in 1886 (Berlin patent 39,369 May 12). According to these patents, the crushed ore was mixed with oils , hydrocarbons and water. Then the pulp received in this way was heated up to boiling . Air bubbles and steam formed during boiling facilitate the flotation of ore particles coated with oil (first patent) or bubbles been generated by the reaction of lime with acid (second patent). The evolution in the design of the flotation apparatus incorporates the following key stages. Further development is connected with the Francis Elmore’s idea to use gas bubbles received at water electrolysis (UK, 13578; 1904). This method was not introduced then, but much later, in our time and on the essentially new technical basis it found a use for sewage treatment (electroflotation). Gas bubbling under vacuum patented also by Elmore (UK, 17816; 1904) obtained a practical use. It should be noted that the method did not lose its importance till now. The design of the camera has been surely optimized (Glembotskii etal, 1963). A year later A. Macquisten (UK, 26712) developed pressure (compression) flotation. Thus, the H.Sulman, H.Picard, D. Bell’s (US, 853120, May 29, 1905) basic patent and the adjoining T. Goover’s patent 1910 (US, 953746) formed the basis of the first and most important element of modern flotation: flotation with air bubbles sucked in from the environment. In 1914, J.Callow received a patent for on an apparatus where air was sparged through the porous false bottom of the cell ( US, 1104755). Woolen fabric folded four times was fixed on a perforated metal frame to be used for air sparging (Gaudin, 1932). The following year Durrel created the prototype of the injection (ejector) apparatus. The jet aerator made it possible to significantly reduce the size of the bubbles, in comparison with the filter cloth. An apparatus with slurry pre-aeration in an airlift prior to feeding into separation cell was developed Wagner in 1917 (US, 1235083). And finally, the first column apparatus with a counter-current of slurry and air was developed by M. Towne and S. Flynn in 1919(US, 1,295,817). ("

Jan 1, 2018

By G. Pahomova

"It developed an alternative to traditional flotation enrichment refractory of complex lead-zinc ores to obtain conditional lead and zinc products. The scheme involves the use of the processing method of gravitational enrichment of the primary cycle and the combined gravity-flotation-hydrometallurgical in finishing. The method has a high level of comprehensive utilization of mineral raw materials in relation to the elements that are extracted in the process of enrichment in lead concentrate, and the increase in recoverable value of processed ores. INTRODUCTION The primary source of lead are complex sulphide lead-zinc ore, lead ore actually rarer. The value of lead and zinc ores (except lead and zinc) is determined by the presence in them of a wide range of associated components: silver, contained mainly in galena; gold; bismuth in the form of its own minerals, but is associated with galena; cadmium contained mainly in the sphalerite; indium, thallium and gallium contained in sphalerite and galena; selenium and tellurium are present as impurities in the sulfide, tellurium is also found in the form of its own minerals. Of note harmful impurities antimony, which is often associated with lead sulphosalts and arsenic, having a substantially own minerals. By quality (content of lead, or the total content of lead and zinc) lead-zinc ores are divided into rich, ordinary and poor; by oxidation - to sulfide (with a lead oxides content less than 15% and zinc oxide content less than 10%), mixed and oxidized (50% oxide); the latter have a subordinate importance as a source of zinc and lead. Traditionally, the most contrasting technological properties of sulfide ores of nonferrous metals considered flotation properties, which determines the priority in the selection of flotation technology of their enrichment. Other methods of enrichment - gravity (jigging and enrichment in heavy suspensions), radiometric sorting (separation) are used as preliminary operations whose main purpose is to increase the content of lead and zinc in the ore sent to flotation, as well as the removing of part of empty rock in dumping tails prior to flotation. Effective implementation of these methods is possible at large size emphasizing in the ore of lead and zinc minerals, which is typical of the rich ores and which so far mainly worked. At the same time, non-ferrous metal ores (polymetallic, lead-zinc, copper-zinc, etc.) have a sufficiently high contrast to gravitational properties since ore minerals have a higher density compared with a rock minerals. But the gravity of the practice of non-ferrous ores enrichment is not widely used, despite its high degree of environmental safety and lower cost expensive."

Jan 1, 2018

By S. Banisi, A. R. Hasankhoei, A. R. Ghasemi, E. Razi, G. A. Parsapour

At the pelletizing plant of the Gol-E-Gohar mining and industrial company two parallel dry closed grinding circuits, each with the average throughput of 300 t/h, are used. Each grinding circuit consists of a burner, a dry ball mill (6.2 m×13 m) and an air separator. The ball mill consists of a 2 m-long drying and an 11 m-long grinding chambers. The iron ore concentrate is fed to the drying chamber by a feed chute. The first 1.35 m of the drying chamber consists of 56 flights in two rows to decrease the feed moisture from 5% to below 0.2% and the rest of dryer chamber consists of deflectors to pass the material to the grinding chamber. It was found that when the feed moisture content increased from 1.3% to 3.5%, the throughput decreased by 12% (35 t/h) indicating a low performance of the dryer. Monitoring the wear rate of flights for a period of 12 months showed that the first 0.8 m length of the flights length did not experience any wear. This means that about 59% of flights do not contribute in material distribution and drying. A DEM simulation of feed chute and the drying chamber demonstrated that due to the inappropriate design of feed chute most of materials do not get in touch with the first 0.8 m length of the drying chamber. To overcome this problem, various feed chute designs with different geometries were simulated by the KMPCDEM© software. With the aim of arriving at a proper material trajectory, where the total length of the flights are used, a new feed chute was selected. The simulation results indicated that if the height of the flights is increased from 1.60 to 2.26 m and the slope is increased from 45 to 48 degrees the material arrive at the first 0.48 m of drying chamber. In this manner, the unused part of the drying chamber decreases from 59% to 36% of the length. After installation of the new feed chute, during a period of three months the throughput increased by 36 t/h.

Jan 1, 2018

By A. Mainza, H. Hill, L. S. Bbosa

"Impact breakage is the most elementary size reduction mechanism in comminution devices. In comminution research, characterization of breakage is primarily concerned with the energy expended to cause it. The main challenges of this approach have been quantifying the actual energy requirements of impact breakage and developing mechanistic models to accurately describe the process. For engineering load analysis, fracture is characterized in terms of strengths such as yield stress and ultimate tensile stress, which govern the maximum loads specific materials can be subjected to before irreversible inelastic deformation and subsequently complete fracture occur. With this approach, the main challenge has been to elucidate the underlying mechanism, in the means that the load causes weaknesses in the material microstructure to act as sites for stress concentrations, leading to crack initiation, propagation and eventual failure. Studies dedicated to investigating particle fracture under impact loading have led to the development of several devices for conducting breakage characterization tests. These devices include the drop weight tester, split Hopkinson pressure bar, rotary breakage tester and the short impact load cell. All these have different particle loading and breakage methods, and thus can yield distinct information which can be compiled together to study a material and the nature of breakage. This work analyses the single impact breakage data obtained across the listed devices. A homogenous ore commonly known as blue stone is used for all breakage tests. The work is conducted using standard procedures specific to each device as closely as possible. Drop weight and rotary breakage tests were used to obtain hardness parameters based on an existing t10 breakage model, while split Hopkinson pressure bar and short impact load cell measurements provided properties based on conventional engineering load analysis. The results were used to highlight the significance of the loading geometry, impact mechanism and impulse on the extent of breakage."

Jan 1, 2018