Search Documents

By Hillary Williams, Ronghao Li, Christopher Marion, Kristian E. Waters, Devin Hundt

"Zircon is an important mineral for ceramic, foundry, casting, and refractory applications; and it is the worlds primary source for zirconium. Zircon can also contain large and valuable proportions of other valuable metals, such as rare earth elements and hafnium. The Nechalcho deposit (Northwest Territories, Canad), is a hard rock REE deposit, which looks to recover zircon for its Zr and REE content. In this deposit, zircon is finely disseminated and associated with predominately silicate gangue minerals. Most of the work to date has focused on the beneficiation of mineral sand deposit, which typically remove silicate gangue minerals through physical separation steps. Therefore, the separation of zircon from silicate gangue, such as quartz, by flotation, has received little attention. This work used zeta potential measurements and microflotation experiments to understand the interaction between zircon and six different collectors (sodium oleate, sodium dodecyl sulphate, dodecylamine, SM 15, K-octyl hydroxamate and Florrea 7510). The results were compared with those of quartz. This study indicated that selective separation of zircon from quartz without the use of selective depressants or activators is likely challenging. The findings suggested sodium oleate and SM 15 only offered selective flotation of zircon in highly acidic conditions. Separation by the flotation of quartz is possible using sodium dodecyl sulphate, dodecylamine and K-octylhydroxamate. However, selective separation is highly dependant on collector dosage, for dodecylamine, and the selective activation of quartz, for sodium dodecyl sulphate and K-octyl hydroximate. Florrea 7510 offered poor recoveries for both zircon and quartz.INTRODUCTIONZircon (ZrSiO2) is a nesosilicate mineral which has a wide variety of applications, due to its hardness, opaqueness and resistance to heat and corrosion. Its major end uses are in ceramic, foundry, casting, and refractory applications (Bedinger, 2017). Zircon is also the most abundant zirconium (Zr) bearing mineral in the earths crust and is the principal economic source of Zr (primarily used in alloys for heat and corrosion resistance) and zirconia (ZrO2) (primarily used in ceramics) (Bedinger, 2017; Milnes and Fitzpatrick, 1989). Zircon forms in silicate melts and can often contain large proportions of other valuable metals such as rare earth elements (REE), and hafnium (zircon is the primary source of hafnium) (Bedinger, 2017; Belousova et al., 2002; Orlova, 2007). A common chemical formula showing the range of substitution in zircon is (Zr,Hf,Th,U,REE,Ca,Fe,Nb,Ta)(Si,P)O4 (Orlova, 2007)."

Jan 1, 2018

By RB. Pedersen, T. Barryere, E. Reeves, A. Stensland, I. Thorseth, T. Baumberger

Venting on ultraslow spreading ridges is far more abundant then previously predicted, and the discrepancy between observed and predicted vent field density may imply that non-magmatic heat sources are common along these ridges (Baker and German, 2004; Escartin et al., 2008; Rona et al., 2010; German et al., 2016). In this study we have estimated the flux from two hydrothermal vent sites situated on the slow to ultraslow spreading Mohns Ridge at the Arctic Mid-Ocean Ridge system (AMOR). The flux estimates have been made using the primordial isotope 3He in the non-buoyant plume above the Loki’s Castle vent field at the northern termination of the Mohns Ridge, and from the Jan Mayen vent fields area situated close to the southern termination of the ridge. Primordial 3He enters the oceans through degassing and mixing with hydrothermal fluids eventually to be discharged at the ocean floor primarily at hydrothermal vent sites and submarine volcanic eruptions (e.g. Clarke et al., 1969; Lupton and Craig, 1981; Lupton, 1998). Once introduced into the water column the concentration will only decrease by dilution due to its conservative behavior in the water column. Water column samples were collected using a CTD (conductivity, temperature, depth) probe (911plus Seabird) with a Niskin water bottle rosette. The water column above the Jan Mayen vent fields (JMVF) was sampled in the years 2006, 2011, 2012 and 2013 (82 samples) and the water column above the Loki’s Castle vent field was sampled in the years 2007, 2008 and 2009 (116 samples).

Jan 1, 2018

By J. Bouchard, A. Clapperton, L. Ebacher, N. Singh

"Canadian Royalties Inc. owns and exploits the Nunavik Nickel project: a copper and nickel deposit in Nunavik, Quebec. Froth flotation is used to produce nickel and copper concentrates. As is the case at other operations, the presence of magnesium is detrimental to the flotation products. In the past year, the exploitation of a new deposit has increased magnesium in the feed. Thus, it has been challenging to meet the required ratio in the final nickel concentrate. In search for a consistent solution for this problematic, an empirical flotation simulator making use of selectivity curves was developed. The circuit was expressed as a system of linear equations, which considered the distribution of copper, nickel and gangue minerals in the different streams. The relative quantities of each mineral are given by the separation efficiency curves of the various banks in the circuit. Three sources of data were used to calibrate the simulator: historical plant data (metallurgical balance), infinite dilution bench-scale flotation tests, and direct sampling of flotation cells. The calibrated separation curves were used to predict the recovery of the different species based on a single mineral recovery. Validation of the simulator showed good fit for the valuable minerals. The simulator was then used to infer the optimal operating conditions of the flotation circuit to optimise magnesium oxide content of the nickel concentrate. Simulation of two re-arrangements of the circuit gave a promising solution with a Fe:MgO ratio 2.42 times higher than the minimum value.INTRODUCTION Canadian Royalties Inc. owns and exploits the Nunavik Nickel project: a copper and nickel deposit in Nunavik, Quebec. Figure 1 shows the location of the mine site. After crushing and grinding, froth flotation is used to produce nickel and copper concentrates. The flotation circuit is designed with multiple stages consisting of bulk copper/nickel flotation, copper/nickel separation, and a separate nickel circuit (bulk float and cleaning)."

Jan 1, 2018

By M. Kadiyski, V. Stoyanova, E. Visariev, V. Stoilov

"The present study deals with copper losses in slag from copper smelting. Copper slag cooling at Aurubis Bulgaria is traditionally done in pits. A new type of slag-cooling is introduced in the site, involving cooling ladles. In a previous study, the ladle cooling process was studied in detail, showing an improvement in the recovery of copper in the slag after flotation. The main reason for better recovery of copper is the increased cooling time, which allows for the accumulation and aggregation of copper droplets. The effects of the newly introduced slag cooling process are studied using optical microscopy and scanning electron microscopy. Cooling in pits and in ladles is compared, based on copper droplet size, distribution and content. Specialized image processing software is employed on images taken with an optical microscope. The results are then compared with a similar technique, available in SEM software. The availability of phase-analysing image software in combination with electron dispersive X-ray spectroscopy makes it possible to study the morphological properties, distribution and chemical composition of the copper droplets. The obtained results confirm the initial conclusions about size, distribution and composition of the copper-bearing particles. A large amount of copper particles is examined showing an obvious increase in their size from pit- to ladle cooling. The results show an increase in the average size of the droplets, which doubles from pit-cooling to ladle-cooling. There is a well-pronounced tendency of decrease of the percentage of droplets in the smallest fraction (<5 µm) in the ladle-cooled slag. In addition, the number of droplets in the larger fractions increases, compared to the ones in the pit-cooled slags. It is believed, that the developed methodology for analysis provides a relatively quick and reliable solution for comparison of the cooling rates in the slag. INTRODUCTION In the process of copper smelting and converting, iron-silicate slags are produced that contain various amounts of dissolved and entrained copper. Different physical and chemical techniques are employed for the valorisation of the remaining metals in the slag – magnetic separation, leaching, roasting, flotation, etc. According to Gorai et al (2003), about 2.2 tons of slag is produced per ton of metal. In 2016, about 20 million tons of copper have been produced globally (www.icsg.org). At an average of 0.5 percent copper content after treatment, these slags contain more than two hundred thousand tons of copper which is lost due to inefficient processing."

Jan 1, 2018

By T. McCallum, C. Cooper, C. Lewis

"Following a successful solvent extraction (SX) pilot plant demonstration in 2016, CYANEX® 600 has been used commercially to recover molybdenum from concentrate leach liquor since March 2017. Consistent with the piloting results, the commercial plant has achieved expected molybdenum recovery, a significant reduction in base consumption, and a step-change improvement in physical performance. This paper highlights the optimization activities and plant performance from startup through normal operation. INTRODUCTION Historically, tertiary amines have been the most commonly used extractant for molybdenum and rhenium recovery. Tertiary amines utilize a protonation of the ligand combined with an anion exchange mechanism as proposed in equations (1-2). R3N + H+ ???R3NH + (1) 4R3NH+ + Mo8O264- ???(R3NH+)4Mo8O264- (2) In addition to the transfer of Mo and Re, the amine transfers acid and other anions to the strip liquor. The undesirable transfer of other species increases base consumption during stripping, impacting operating costs. Additionally, lower solubility of molybdenum-amine complexes create operational challenges, resulting in diminished physical performance. The presence of colloidal Si in concentrate leach liquors and the formation of Pickering Emulsions adds to the physical plant performance challenges with the amine extractant. CYANEX® 600, a phosphinic acid-based extractant, uses a cation exchange mechanism proposed by equation (3). 2(H2R2) + MoO22+ ??(HR2)2MoO2 + 2H+ (3) The cationic exchange mechanism eliminates chemical transfer of acid and other anionic impurities and avoids some of the physical challenges of the amine extractant (emulsion and 3rd phase formation). In addition, the reagent offers high selectivity for Mo over Re, which may be desirable in certain moly pressure oxidation (POX) flowsheets. Alkali base (ammonium hydroxide, sodium hydroxide, sodium carbonate, etc.) is used for molybdenum stripping. Therefore, reduction or elimination of chemical acid transfer from extract can significantly reduce base consumption in strip. Extensive laboratory and pilot plant testing was completed to evaluate the use of CYANEX® 600 for molybdenum recovery at Freeport-McMoRan’s Bagdad operation. The test work and pilot demonstration confirmed a reduction in base consumption along with improved selectivity. In addition, the evaluation highlighted a step-change improvement in physical performance over the incumbent amine extractant. The decision was made to convert the commercial operation to CYANEX® 600 in March 2017."

Jan 1, 2018

By K. V. Raj, A. Miller

"Workers at mineral processing facilities are often exposed to high levels of dust generated when ores are processed. Crushing, grinding, screening, and other processes generate large quantities of dust, which can exceed the threshold VALUES (prescribed by the Mine Safety and Health Administration (MSHA). Many ores contain quartz (silica), which has been known to cause serious health problems in workers over time. Given the structure of mineral processing plants, the airflow regime is not coherent inside the building, which may lead to multiple recirculation zones. These recirculation zones can trap dust, and concentrations of dust can then rise over time. Therefore, there is a need to understand the airflow phenomenon that occur inside of mineral processing facilities and how these occurrences interact with the dust generation processes to identify zones of potentially high dust concentration. Computational fluid dynamics (CFD) modeling can give a better understanding of the airflow and help recommend designs and methods to mitigate the high dust concentrations in a mineral processing plant. This paper presents the CFD modeling of airflow inside of a mill building to demonstrate airflow patterns that will affect the generation and subsequent dispersion of dust due to crushing, grinding, and other activities. This study was conducted by researchers from the National Institute for Occupational Safety and Health (NIOSH). INTRODUCTION In a mineral processing facility, minerals go through various mechanical processes in order to reduce their size for separation of economic minerals from gangue minerals to produce a final marketable product. This research, conducted by the National Institute for Occupational Safety and Health (NIOSH), focuses on ore mills in metal and nonmetal mining (MNM) operations, but the applicability of the approach will be valid for any large structure where workers are exposed to airborne contaminants. The processes of crushing, grinding, cleaning, drying, and product sizing in these facilities generate a large amount of dust, creating hazardous conditions for the workers in these facilities. This is highlighted by the fact that MSHA sampling data for the years 1997–2012 indicate that 12.3% and 15.9% of the gathered samples were over 100 µg/m3 for silica for metal and nonmetal mills, respectively [1]. Mineral processing operations typically use some type of engineering control to address their most significant dust sources. Engineering controls include such approaches as bag-house-type dust collectors, scrubbers, and electrostatic precipitation [2]."

Jan 1, 2018

By K. B. Han, S. Winkler, M. J. Benoit, M. J. Worswick

"Automotive heat exchangers are fabricated by forming multi-layered aluminum (Al) alloy brazing sheets into the desired geometry and subsequently passing the assembly through a furnace for brazing. As manufacturers seek to use thinner gauge and higher strength sheet to reduce vehicle weight, forming of the Al alloy sheets has become a challenge. Warm forming has previously proven to allay these forming concerns, but no consideration was given to the effect of increasing the forming temperature on brazing. Recently, it was shown that annealed sheet was more susceptible to the detrimental phenomenon of liquid film migration (LFM) during brazing if formed above 150°C, while work hardened sheets showed no increased susceptibility to LFM with increasing forming temperature, up to 250°C. In the current study, the brazing performance of simulated battery cooling plates was investigated. The plates were fabricated both from fully annealed and work hardened sheets. Brazing was assessed by microstructural evolution during a brazing cycle. The post-brazed microstructure varied with strain and forming temperature in plates made from annealed sheets, while no variation in microstructure with location or forming temperature was observed in plates formed from work hardened sheets.INTRODUCTION Since the 1970’s, one common method of fabricating automotive heat exchangers has been by forming multi-layered aluminum (Al) alloy sheets, and subsequently brazing the formed components together in a controlled atmosphere furnace. The Al alloy sheets used are comprised of at least two Al alloys roll bonded together, but can consist of additional layers, depending on the application; at minimum, the sheets are comprised of a core and clad layer. The core layer, often an AA3xxx alloy, remains solid throughout processing and provides strength to the assembly. The clad layer is always one of the AA4xxx series alloys which, due to their high silicon (Si) content, have a melting temperature range well below that of the core alloy. When the sheet is passed through the brazing furnace, the clad alloy melts to provide the brazed joint filler metal throughout the assembly, while the core alloy remains solid. In order to achieve cost and weight savings, heat exchanger fabricators have used Al alloy sheets with reduced thickness. However, deformation and brazing of these increasingly thin components remains a concern (Zhao & Woods, 2013). Furthermore, springback has been observed after forming sheets of higher initial strength (i.e. work hardened conditions), leading to flatness issues of formed components. Consequently, the ability to form high quality brazed joints is difficult in components formed from higher strength brazing sheets."

Jan 1, 2018

By R. Quentin Eades, Kyle Perry

"Surface mines continue to implement highwalls for several reasons, such as increasing recovery, improving margins, and justifying higher stripping ratios. Highwall stability is a complex issue that is dependent upon a variety of mining and geologic factors, and a safe design is necessary for a successful surface operation. To improve highwall stability, it is important to understand the connection between local geology and blasting.Explosives are employed throughout the mining industry for primary rock breakage. There are a number of controlled blasting techniques that can be implemented to improve highwall stability. These include line drilling, smooth wall blasting, trim blasting, buffer blasting, air decking, and presplitting. Each of these techniques have associated advantages and disadvantages. Understanding local geology is necessary for selecting the appropriate controlled blasting technique. Furthermore, understanding the limitations and conditions for successful implementation of each technique is necessary. A discussion of the impact of geologic conditions on highwall stability is provided. Additionally, discussion is provided for the successful incorporation of the controlled blasting techniques listed above, and the associated mining and geologic factors that influence the selection and design of controlled blasting plans. Finally, a new methodology is proposed.INTRODUCTIONExplosives are used throughout the mining industry as the standard for primary rock breakage, a critical part of the mining cycle. In 2015, the U.S.. consumed 2.2 million tons of explosives (Apodaca, 2015). The coal mining industry accounted for the majority of explosive consumption, accounting for approximately 63% of total explosives. The quarrying and nonmetal mining industries accounted for 12% of explosive consumption, and the metal mining industry accounted for 9% (Apodaca, 2015). This constitutes 84% of the explosives used in the U.S. However, the energy released during the detonation process is often in excess of that required to adequately fragment the surrounding rock (Jhanwar and Jethwa, 2000). This excessive energy, along with over confinement and poor blast geometry, will cause damage to the undisturbed rock mass beyond the intended boundary of the blast. This event is known as overbreak or back-break (ISEE, 2011)."

Jan 1, 2018

By A. Gueciouer, A. Akkouche, K. Chalah, A. Benmounah

"Drilling solid waste is a typical industrial solid waste, and it is a major pollutant source to ecological environment. Generally, waste management dewatering systems separate solids and fine particles from the liquid phase of drilling fluid, thereby leaving a clarified aqueous solution and allow the cleaning of waste fluids. Typically, dewatering waste management systems clean drilling fluid through coagulation, flocculation and/or mechanical separation. Chemicals used in dewatering are based on the coagulation-flocculation process, which it facilitate the removal of suspended solids and colloidal particles. The factors which can promote the coagulation-flocculation are velocity gradient, contact time, and PH. The objective of this work is to optimize a formulation adequate for dewatering based on the coagulation-flocculation process used coagulant (Aluminum sulphate), anionic flocculants (Partially Hydrolyzed Polyacrylamide) and anionic polyelectrolytes (in solid form with linear chain with very high molecular weight). The results obtained show the good efficiency of the coagulant and flocculants. INTRODUCTION Rig site dewatering of drilling fluids with recycling of processed water can help an operator to comply with environmental rules by reducing volumes of waste and reducing long term liabilities. It can also reduce disposal costs and provide a cleaner drill site overall. Most of the environmental concerns during the 1980s involved hazardous materials and toxic wastes. Drilling fluids, many of which are chemically benign, have escaped many of the difficult-to-comply-with rules and regulations. During the 1990s, however, operators may be required to submit a written plan for liquid waste reduction for even nonhazardous materials. Many states and local agencies may institute total bans on oil field wastes. Drilling rigs typically produce about 1 bbl of liquid waste for every 1 ft of hole drilled. Thus, a typical drilling operation can produce a large quantity of waste [1]. To improve the dewaterability of sludge, different pretreatment processes have been widely studied and developed including thermal, chemical, magnetic, mechanical, acoustic, electric, electro-acoustic and their hybrid treatment processes [2]. Rig site dewatering (figure 1) is the process of injecting coagulants or flocculating chemicals into the mud entering a large clarifying centrifuge. Coagulation occurs when the solid and allowing it to be attracted to other solids by van der waals forces. Flocculation is the binding of individual solid particles into aggregates of multiple particles. It is physical, rather than electrical, and occurs when one segment of a flocculating polymer chain absorbs simultaneously onto more than one particle [3]."

Jan 1, 2018

By Wei Sun, Chengwei Li, Zhiyong Gao, Yuehua Hu

"Grinding for mineral liberation is a prerequisite for a successful flotation separation. Different grinding media produce mineral particles with different morphologies and surface properties. In this study, the surface physicochemical properties of fluorite particles produced by ball and rod mills were systematically investigated through single mineral flotation experiment, wettability measurement, X-ray diffraction (XRD) test and scanning electron microscopy (SEM) observations. The XRD observations reveal that the surface exposure degree for both mill particles follows the order {111} > {110} > {100}. The difference lies in that the rod mill ones have a higher exposure of more reactive {110} and {100} surfaces, leading to a stronger interaction with the collector. The difference also leads to their higher elongation and lower roundness values of rod mill particles which are beneficial for the particle-bubble attachment by shorting the induction time. The wettability and flotation results show that the rod mill ones have a lower critical surface tension and a greater hydrophobicity when treated with the collector solution and accordingly perform a higher flotation recovery. This work, for the first time, revealed the importance of the exposure of crystal surfaces in determine the shape factors and reactivity of the mineral particles and will help provide guidance for optimizing flotation separation and particle surface modification. INTRODUCTIONFluorite (CaF2) is the most important source mineral for producing F-based chemicals and materials which are widely used in industrial, environmental, and medical fields [1, 2]. In ore deposit, there are two kinds of occurrence forms of fluorite mineral. Firstly, the fluorite mainly coexisted with the gangue minerals like calcite (CaCO3) and quartz (SiO2). Because of their similar density and fine-grained dissemination in ore deposit, ball mill grinding before flotation separation has been widely applied to produce relatively fine particles [3]. Secondly, the fluorite is often associated with other valuable minerals with higher relative density such as scheelite (CaWO4) and cassiterite (SnO2). Due to their obvious density differences and coarsely grained distribution in ore deposit, rod mill grinding before gravity separation has been usually used to produce more uniform particles and avoid over-grinding [4-6]. After the gravity separation, a flotation separation is also employed to beneficiate the fluorite [7]."

Jan 1, 2018

By A. V. Yevdokimov, Ye. V. Bogorodsky

The paper presents the results of the research on the development of gravity concentrates processing technology (gold grade is from 50 g/t to 1 kg/t and over) using intensive cyanidation with gold recovery to pregnant solutions followed by precipitation of metals from them using various methods. Test work and pilot plant results confirm that a new developed hydrodynamic regime provides an efficient treatment of gravity concentrates of polydisperse composition without their grinding and preliminary desliming. The resulting pregnant and washing solutions are amenable to metals recovery using electrowinning, cementation onto zinc dust and CIS. Cone plants with a lower ball valve for cyanidation of unground gravity concentrates developed by IRGIREDMET JSC have been successfully tested at a number of Russian operations. Currently, a modular plant equipped with gold electric precipitation from pregnant solution unit is successfully operated at a Russian gold processing plant. Cyanidation of the resulting high-grade gravity concentrate is carried out at the concentration of 8-10 g/L NaCN and 10 g/L NaOH. Gold recovery to the solution is 97-98%. Electrowinning is carried out in flow cell GNC-40M. In this case, the residual gold concentration yield is 0.3-0.5 mg/L. Also, a modular plant for relatively low-grade middlings (50-100 g/t Au) of gravity concentration has been introduced. The concentration of NaCN and NaOH is 2-3 g/L and 1.5-2 g/L, respectively, during leaching. This plant is equipped with a unit for gold cementation from pregnant solution with zinc dust. This cementation unit is of original design. It is made in the form of a filtering device and is composed of several layers of carbon fiber which contacts with zinc powder. The residual gold concentration yield from a cementation unit is less than 0.1 mg/L. Gold recovery is 93-97%. In 2017-2018, the introduction of intensive cyanidation modular plants to gravity concentrates will be planned at new projects of Russia and the CIS.

Jan 1, 2018

By S. Rupprecht

"INTRODUCTION This paper addresses the prevalence of poor public reporting practices of Coal Exploration Results, Coal Resources and Coal Reserves in southern Africa. Currently, the reporting of coal tonnage without supporting coal qualities or “saleable” tonnes and quality is a poor reporting practice that occurs far too often. Not all coal is equal – therefore it is extremely important that investors or potential investors are provided with the full details of both run-of-mine (“ROM”) and Saleable coal tonnage, their associated qualities and other material and relevant information. Competent or Qualified Persons should note that publicly reported information should be sufficient to enable an informed reader to make a reasonable and balanced assessment of the significance of the information provide. “Companies are encouraged to provide information in their Public Reports, which is as comprehensive as possible” (CRIRSCO, 2013): too often this isn’t the case and material matters are either not reported or inadequately disclosed. According to the South African National Standard (SANS) 10320:2014 draft document - “tonnage and coal quality that will be available for sale, either in the raw ROM state (raw Saleable) at a specified moisture content, or after beneficiation of the ROM coal by processing operations to produce materials at specified qualities, size ranges and moisture contents. The assessments must demonstrate that at the time of reporting, the marketing of the products is reasonably justified. The basis of the predicted practical product yield to achieve the Saleable Coal Reserve must be stated. The moisture basis of reporting shall be stated.” As an example to why coal qualities are so important to the public, the requirements of South Africa’s electric public utility (Eskom) power stations are highlighted. The Kendal power station, commissioned in 1988, operates at a Calorific Value (“CV”) range of 19 to 20MJ/kg, an Ash content between 29 and 34% and Volatiles between 20 to 21%. Other power stations, such as Kriel or Hendrina, may require different qualities such as a CV range of 22 to 23MJ/kg, an Ash content between 20 and 28% and Volatiles between 22 to 23%. Thus, in terms of domestic saleable coal, it isn’t just about reporting the coal qualities but also informing the investor as to which power station the coal is intended to be sold as “boilers are designed to burn particular qualities of coal” and “it is not always possible to transfer coal between stations because of different quality requirements at each station” (Chetty, 2010). Sulphur content is also another important quality with the ideal coal content having a quality of less than 1% Sulphur."

Jan 1, 2018

"The JKMRC researchers have been redeveloping the suite of breakage testing techniques to more realistically align with the breakage environment in comminution equipment. Computational modelling, especially with the DEM, has highlighted the modes of impact and contact, along with the energies of these interactions in a wide range of equipment. This has driven the need to match these modes in laboratory ore characterisation tests. The objective has been to build a continuum of breakage tests and associated models that span the required range of breakage forces and environments. The ore sample is subjected to a sequence of tests covering: abrasion (surface breakage) of angular through to smoothed particles; single particle impact from high energy single impact breakage down to low energy; incremental breakage covering 60 mm down to 50 µm particles; particle strength distribution; and bed breakage over a range of compression and energy input. These tests are suited to multi-component ores with a distribution of strengths. A modelling technique is also being developed to utilise primary breakage for modelling breakage under different types of confinement. This paper draws together these techniques, previously published by the authors, into a coherent whole. The suite of tests is approaching the point where a fixed set of tests can be used to model the performance of a full range of equipment, removing the need to conduct repeat ore characterisation tests for each different piece of equipment incorporated in a circuit design. This path should open up the application of different circuit configurations and novel equipment in comminution circuit design.1 INTRODUCTION Comminution modelling utilizes a wide range of ore characterisation techniques and methods to deal with the range of comminution equipment available for production use. In general, the tests have been designed to correlate with specific pieces of equipment, using calibration factors to provide the link between the small-scale test and industrial-scale performance. The majority of tests focus on estimating the power requirement of process equipment to achieve a desired throughput and grind size. Overall, this approach has achieved acceptable outcomes in the past, but the reality is that equipment sizing suffers from considerable uncertainty, in excess of ±20% is not uncommon. This uncertainty is covered by safety margins and automatic scaling factors in equipment selection. In striving to improve reliability, the industry tends to add more adjustment factors to the tests, and design margin rather than question the basic validity of the testing process. As the tests are often correlated to production equipment via carefully guarded databases, they are also locked into historic operating inefficiency, not providing direction or revealing opportunities to improve production efficiency in comminution equipment or circuits. Safe in the knowledge that they are achieving the expected production based on test work predictions, a site is unlikely to set their sights on reducing specific energy consumption by 10%."

Jan 1, 2018

By L. Yan, T. Lutz, J. Noll

"Mine disasters, such as fires and explosions, can create a hazardous atmosphere due to the generation of carbon monoxide (CO). After a mine disaster, contaminated mine air can enter the refuge alternative (RA) as miners enter. Most built-in-place (BIP) RAs use an air delivery system to provide an unlimited supply of breathable air through a borehole which also serves to purge contaminants. In order to determine what levels of contaminants enter the RA, researchers from the National Institute for Occupational Safety and Health (NIOSH) conducted testing in NIOSH’s Pittsburgh Experimental Mine using groups of 5, 15, and 30 subjects entering the RA. The experiment used sulfur hexafluoride (SF6) as a tracer gas that was released into the air outside of the BIP RA to establish a uniform concentration. After the human subjects entered the BIP RA, the SF6 levels inside the RA were measured to quantify how much of the tracer gas entered the BIP RA. In tests conducted while the borehole air supply was left off as test subjects entered, interior contaminant levels were less than 3% of the exterior concentration. In tests conducted with the borehole air supply activated as test subjects entered, the interior contaminant levels were measured at less than 2% of the exterior concentration. Considering a mine disaster can result in 10,000 ppm of CO in the mine atmosphere, these percentages indicate that unhealthy CO concentrations that may lead to headaches, dizziness, and loss of judgement can occur in a BIP RA. This information will help mines make decisions concerning air locks, air delivery systems and a determination if purging mechanisms are necessary. INTRODUCTION The Mine Improvement and New Emergency Response Act of 2006 (MINER Act) was enacted in the wake of three mine explosions/fires that claimed 19 lives that year. Intended to help improve underground coal mine accident preparedness, the MINER Act includes provisions that target mine safety issues in areas such as emergency response planning, adoption of new technology, training and education, and enforcement of mine safety standards (MSHA, 2006). Section 13 of the MINER Act specifically directs the National Institute for Occupational Safety and Health (NIOSH) to provide for research into the effectiveness and viability of RAs for underground coal mines. This mandate culminated in the 2009 adoption of changes to the 30 CFR mining health and safety regulations, requiring underground coal mines to provide RAs capable of maintaining a life-sustaining environment for persons trapped underground. Such RAs can be either pre-fabricated or BIP shelters. The regulatory changes also include provisions establishing requirements for Mine Safety and Health Administration (MSHA) approval of RAs and their components, and among these provisions are numerous criteria for providing a safe, breathable atmosphere within RAs."

Jan 1, 2018

By D. Marcotte, R. V. Dutaut

"In mineral resource evaluations, geostatistical methods known as global change of support allow prediction of the theoretical histogram and gradetonnage curves prior to interpolations or simulations of grades. Two methods commonly used by professionals to guide the choice of interpolation parameters and assess results are the discrete Gaussian model (DGM) and the indirect lognormal correction (IndLog). These models rely upon an estimate of the dispersion variance of the blocks, which is derived by numerical integration of the variogram model over a discretized block. Due to difficulties in obtaining well-formed traditional experimental variograms (especially in the presence of outliers and limited clustered data), many professionals prefer to use ‘normalized’ variograms such as correlogram (non-ergodic variogram), pairwise-relative, or variogram of the normal score transform. A series of simulations with different grade distributions and variogram models are used to assess the performances and robustness of the various variogram estimators with respect to the DGM and IndLog global change of support. Our results show that the traditional variogram, the correlogram, and normal score variogram have better performances, compared to pairwise, for both DGM and IndLog. Moreover, DGM provided better results than IndLog for the grade distributions that are not strictly lognormal. These findings provide valuable guides for geostatistics practitioners. IntroductionWhen reporting resource estimates,practitioners are required to follow generalstandards described in the NI43-101 (CIMguidelines), JORC, or SAMREC codes. One cangenerally recognize three main parts directlyrelated to the block model:•,Pre-processing: exploratory data analysis (EDA), domaining, capping, compositing, declustering, variography•,Processing: block size, neighbourhood, interpolation types (linear or nonlinear)•,Post-processing: classification, reporting.Pre-processing aims to simplify and strengthen the processing step. Ideally, domaining, capping. and compositing is aimed at defining a single homogenous population. During the processing phase, a common practice is to use a block size corresponding to the planned selective mining unit (SMU). In most precious metal deposits (gold, notably), the SMU size is frequently smaller than the recommended half data spacing (Journel and Huijbregts 1978), resulting in high estimation variance and either a high degree of smoothing if the regression slope is managed or a high degree of conditional bias if it is not. Most actual resource estimates are made using block sizes between one-quarter to one-sixth of the average data spacing, sometimes even smaller. In addition to the block size, the interpolation choices for the neighbourhood selection and interpolator (e.g. inverse distance (ID) or ordinary kriging) are often based on the Qualified Person’s (the QP) experience and some basic validation plots that often do not consider the conditional bias (e.g. trends or SWATHs plots, which are designed to compare two sets of population using a one-dimensional graph)."

Jan 1, 2018

By Y. Y. Li, Q. Chen, Y. X. Cai, Q. Zhang, S. Mao

"Due to the influence of combustion conditions, the fly ash produced by some power plants has the problem of high-carbon content. The unburned carbon in fly ash can be removed by flotation, and the decarbon tailings should reach the national standard level I fly ash. The fineness of the requirement is one of the important indicators and is also an important factor affecting the tail ash activity. In this paper,adopting two methods investigate the effect of particle size on the flotation index: one is direct flotation of fly ash, and the other way is wet grinding + flotation of fly ash, comparing the two methods and selecting the appropriate process,which provides a way for the effective utilization of fly ash. INTRODUCTION Fly ash is a solid waste discharged from coal-fired power plants. The annual amount of emissions of fly ash are very large in China. The amount of fly ash were discharged from coal-fired power plants are increasing gradually, and the amount of fly ash stored has exceeded 2.5 billion tons, but the comprehensive utilization of fly ash is not high, which brings about a huge environmental problems( Lu et al.,2011). Carbon is a harmful component of fly ash in cement and concrete application (Zhang et al.,2008). Fly ash decarburization is an essential link to improve the utilization efficiency of fly ash and the reduce pollution ( Yang et al.,2012). Carbon is selected from fly ash to make full use of fly ash resources and improve utilization of fly ash (Li et al.,2008). In this paper, the flotation decarburization of high-carbon fly ash is studied, through comparing the grinding and not-grinding processes, optimizing the separation process of fly ash, which provides a way for the effective utilization of fly ash."

Jan 1, 2018

By G. Weingrill, H. Flachberger, J. Neubacher

The so called Bublon®-process is an innovative process for the controlled expansion of volcanic glasses such as Perlite and for thermal treatment of other minerals. In this manner, functional light fillers with astonishingly altered physical properties can be manufactured. In contrast to conventional Perlite expanding processes no fossil fuels are burned in order to achieve the expansion. Instead, the feed material is heated electrically mainly by radiation based on heat transfer from heating elements. The main advantage is the better controllability of the production process. Therefore, the heating elements are segmented along the flow of the particles, hence in direction of the ongoing expansion. Overheating of the particles, which ultimately leads to the destruction of the particle surfaces and consequently decreasing the quality of the expansion product, can be reduced significantly. Due to flow characteristics and settling behaviors of fines the lower particle size limit of the feed in this process is restricted to not less than 100 µm. Otherwise process instabilities are to be expected. Manufacturing industry demands light and fine hollow microspheres. Therefore, a proven cooperation between Montanuniversität Leoben and Bublon GmbH was formed to develop a new process called ‘Bublite’. This issue was addressed by changing the conveying principle into a pneumatically conveying system transporting particles from the bottom to the top of the kiln by the means of a drag flow. This approach makes it possible to handle the difficult flow patterns in the kiln and to control the retention time of the particles in the heat transfer zone. As a result, it is now possible to expand very fine Perlite particles into a high quality functional lightweight filler with a glazed-closed surface. The dependence of the polymer industry on importing this kind of fillers from overseas can be reduced by producing it close to sites of demand. Also the Perlite mining and processing companies benefit from this technology because the mine lifespan and the output of the processing plant can be increased.

Jan 1, 2018

By Behrouz Ohadi, Kamran Esmaeili, Bibhu Mohanty

In most metalliferrous open pit mines with heterogeneous orebodies, blast-induced rock movement is a crucial outcome that has unfavorable impact on ore and waste segregation in the post-blast muck pile, resulting in either ore loss (the ore is misclassified as waste and sent to the waste rock dump) and/or ore dilution (waste is misclassified as ore and sent to the processing plant). While many studies have been carried out to assess the influence of blast design parameters on blast-induced rock movement, the influence of rock mass characteristics in these studies have been overlooked.

Jan 1, 2018

By P. Latostenmaa, T. Hailemariam, M. Lundström, P. Halli

Doré process is unique way to treat precious metals in the copper electrorefining plant, since it uses anode slime as a raw material. In this pyrometallurgical process, also slag is produced together with Doré metal. However, the process is never ideal, and a part of metal is always lost into the slag. By using Doré slag as raw material for simply mineral acid leaching, some of the lost elements can be extracted and recovered, thus, increasing the sustainability and keeping metals in the circular economy loop. The Doré process itself is developed to convert almost all precious metals and PGMs in the Doré metal, leaving other elements into the slag fraction. The Doré slag consist of slag formers, such as borax and silica based minerals, but contain also traces of sealing materials. In addition, the Doré slag is rich in metals present in the anode slime, such as Cu, Bi and Sb, which are not converted into the Doré metal. There are only few published applications at the precious metal plants, where conservative grinding and flotation circuits have been utilized for the enrichment of valuable metals present in the Doré slag fraction (Godbehere, P.W., 1983; Segawa, C. and Kusakabe, T., 1996). However, the present study shows an alternative approach for the recovery of metals present in the Doré slag by hydometallurgical approach. The study focus on direct mineral acid (aqua regia) leaching of metals present in the Doré slag. The initial dissolved concentrations of Cu, Bi and Sb from Doré slag in the temperature range of 30-50 °C under oxygen purging with addition of 1 vol-% of H2O2 are presented. Chemical and mineralogical analyses were performed for the raw material, leaching residue, and leaching solutions in order to ascertain the leaching behavior of the metals of Bi, Cu and Sb.

Jan 1, 2018

By L. O. Filipov, N. E. Menad, A. Geneyton

"Zeta potential of synthetic monazites presenting various compositions were measured to investigate the effect of the main lanthanides substitutions on electrophoretic mobility and resulting IEP. The measurements are performed in a CO2 depleted and enriched solutions showing both reduced influence of monazite chemistry and strong influence of ions resulting from the solubilization and dissociation of CO2. The influence of oleic acid on the electrophoretic mobility of those monazites was also investigated. The influence of pH on oleate adsorption was studied using a bubble/particle adhesion system. Adhesion strength measurements were performed on pure synthetic monazite-(Ce) and monazite-(La). An extensive thermodynamic model of monazite in water was developed to highlight correlations between lanthanides hydroxides/carbonates species concentrations in the bulk solution and oleate adsorption. Based on electrophoretic measurements, advanced thermodynamic consideration and adhesion measurements, further details of the oleate adsorption model on monazite surface were proposed.INTRODUCTION Electrophoretic and potentiometric data on monazite and, a fortiori, other rare earth semi-soluble salts such as bastnaesite are extremely erratic (Chelgani et al. 2015). The isoelectric points measured with electrophoretic mobility methods range from 4.7 to 6.5 although sporadic data indicates an IEP (isoelectric point) far from that range. Different explanations are proposed in the literature to explain the IEP variability notably the numerous chemical substitutions that frequently occurred within monazite crystal lattice (Chelgani et al. 2015). Based on lanthanides speciation diagram, several authors highlighted the influence of specific lanthanide species on the flotation performance of rare earth semi-soluble salts when carboxylate or hydroxamate collectors are used. Although lanthanides ions have a great affinity for carbonates groups (Kragten et Decnop-Weever 1987), lanthanide (hydrogen) carbonates were not implemented in speciation diagrams. In this work, an advanced thermodynamic model is proposed to highlight correlation between flotation performance and lanthanide species predominance but also concentrations. Qualitative measurement of the monazite surface hydrophobicity are performed through tests of adhesion of coarse monazite particles onto bubbles. Since flotation and microflotation technics are highly influenced by hydrodynamic parameters, this method was investigated to obtain a sharp contrast between appropriate and inappropriate pH conditions. This paper is to investigate 1) the effect of lanthanides substitution on monazite surface properties through zeta potential measurements, 2) the mechanism of adsorption of carboxylates on monazite surfaces and 3) the effect of CO2 on monazite surface properties and carboxylates adsorption."

Jan 1, 2018