Search Documents

By John C. Niedzielski, A. Frances Ackerman

The existing US-70 Bridge over the Gila River at Bylas, Arizona is planned to be replaced due to its current poor condition. The replacement bridge is planned to be a 15-span, 1,904-foot (580 meter) long bridge, the third-longest bridge in the state highway system. Within the Gila River floodplain, granular alluvial soil is underlain by cohesive lacustrine soil; bedrock was expected due to nearby terrain but not encountered within the geotechnical exploration depth of 166.5 feet (51 meters) or less. Based on the anticipated loading conditions, design scour depths and the soil conditions, the full structural loads are carried by large diameter drilled shafts; therefore accurately determining the axial capacity of the proposed drilled shafts has important practical and safety implications. The conventional methods for axial capacity determination may be overly conservative to use for design in the site’s layered granular and hard clay soils. An Osterberg cell load test was performed to obtain detailed information on the load transfer from the drilled shaft in side friction and base resistance to allow optimization of the bridge foundation design. The fullscale field test played a significant role in the design of the project’s deep foundations, notably, by incorporating the specific subsoil properties and consequently, an exact prediction of the load-settlement behavior under loading. This paper provides the results of the geotechnical site investigations, drilled shaft load testing procedures, and shaft load distribution from the load test results. Comparisons were developed between predicted axial capacities of drilled shafts using several design methodologies and the axial capacity measured from static load testing. The load test results showed that underestimation of the axial capacity is evident using conventional methodologies. The exact prediction of the load-settlement behavior under loading combined with a site-specific design approach, resulted in a substantial reduction of foundation costs due to reduced drilled shaft dimensions.

Jan 1, 2017

By J. Zhai, Z. Yin

"The electrokinetic and flotation behaviors of ilmenite using lead ions as the activator and sodium oleate as the collector were studied. The results of microflotation show that the flotability of ilmenite can be improved by lead ions obviously. The isoelectric point of ilmenite increases from 5.32 to 7.7 after the addition of lead ions because of the adsorption of Pb2+ and Pb(OH)+. The results of zeta potential measurements and the collector adsorption density calculation show that the adsorption of sodium oleate on the ilmenite surface via chemisorptions in addition to electrostatic interactions. Besides, the adsorption density calculation results show that as the addition of lead ions as the activator, the adsorption amounts of collector are greater than those without activation which is in aggrement with the flotation behaviors. INTRODUCTION Ilmenite, as an oxide mineral of formula FeTiO3, is usually used as the main resource of the extraction of titanium (Bulatovic and Wyslouzil, 1999). There are many researches showing that the conventional methods, such as gravity separation, magnetic separation and flotation, do not work efficiently as expected (Mehdilo et al., 2015; Zhu et al., 2011). Nowadays, to produce ilmenite concentration feasibly and efficiently, these separation methods above are combined for a reason that the raw ilmenite ores are characteristic of poor, fine and complicated. Moreover, surface modification, such as surface dissolution method, microwave irradiation and oxidation roasting, is applied to improve the flotability of ilmenite currently (Welham and Llewellyn, 1998; Zhang and Ostrovski, 2002). Generally, fatty acid salts are used as the collector for the flotation of oxide minerals and sodium oleate is usually used as the collector for the flotation of imenite ores (Fuerstenau and Pradip, 2005). The mechanism, such as individual ion electrostatic adsorption, chemical adsorption, ion–molecule dimeric complex adsorption, and the coadsorption of ion and molecule, have not been discussed systematically using sodium oleate as the collector in the flotation of ilmenite (Somasundaran, 1983). Under the activation circumstance using the lead ion as the activator and sodium oleate as the collector, the interaction mechanism seems to be still unclear. In the present study, the interaction mechanism between ilmenite and sodium oleate using lead ion as the activator are studied by microflotation, zeta potential measurements and adsorption density calculation. EXPERIMENTAL Materials and reagents Pure ilmenite minerals were obtained from Panzhihua, Sichuan province, China. The minerals were ground in a porcelain mill with an agate ball. Following that, the prosucts were sieved, and the samples of -0.074+0.038 mm size fraction were used for the microflotation experiments. The results of XRF show that the content of titanium element is 30.58%, showing that the purity of ilmenite is above 90%. On the basis of the results of XRF, it is determined that the purity of ilmenite is very high and meets the needs of microflotation"

Jan 1, 2017

By P. Bissert, L. Yan, D. Yantek

"Federal regulations require refuge alternatives (RAs) in underground coal mines to sustain life for 96 hours while maintaining an apparent temperature (AT) below 35°C (95°F). NIOSH research has shown that heat and humidity buildup is a major concern with RAs because they have a limited ability to dissipate heat, and high internal air temperature and relative humidity (RH) may expose occupants to heat stress. The heat transfer process within and surrounding an RA is very complex and is not easily defined analytically nor experimentally. To investigate heat and humidity buildup in RAs, NIOSH conducted multiple in-mine 96-hour tests on a 6-person metal-type RA, a 23-person tent-type RA, and a 10-person tent-type RA. The test results show that when moisture was introduced into the tests to represent perspiration and respiration from miners (wet tests), the average measured internal air temperature at midheight increased by 7.7°C, 9.4°C, and 10.5°C, and the RH approached 95%, 94%, and 88%, respectively. For the dry tests when no moisture was introduced, the average internal temperature increased by 8.4°C, 10.3°C, and 12.6°C, respectively. INTRODUCTION If an accident occurs in an underground coal mine, miners who cannot escape from the mine can enter an RA for protection from adverse conditions, such as high carbon monoxide levels. One of the main concerns with the use of mobile RAs is the thermal environment inside the RA. The metabolic heat of the occupants and the heat released by the CO2 scrubbing system will cause the interior air temperature to increase. Moreover, the humidity within the RA will increase through occupants’ respiration and perspiration and from the chemical reaction within the CO2 scrubbing system. The internal thermal conditions can subject miners to heat stress, which can lead to heat exhaustion, heat stroke, or even death depending on duration and magnitude of exposure. MSHA regulations require that RAs must be designed to ensure that the internal apparent temperature does not exceed 35°C (95°F) when the RA is fully occupied [1]. Apparent temperature (AT) is a temperature-humidity metric for the perceived temperature caused by the combined effects of air temperature, relative humidity (RH), and wind speed. It is used to assess the perception of indoor temperatures when workplaces are not sufficiently heated, cooled, or insulated to provide comfortable or healthy conditions. Before a mobile RA can be deployed at an underground mine for emergency usage, it must be tested to show that its internal AT when fully occupied will not exceed the 35°C (95°F) limit. For practical reasons, RA manufacturers usually conduct their tests at above-ground test facilities. To investigate RA thermal response in an in-mine environment, NIOSH conducted multiple 96-hour tests on a 6-person metal-type RA, a 23-person tent-type RA, and a 10-person tent-type RA in its underground coal mine facility. The work described in this paper could be used by RA manufacturers to determine a final temperature rise based solely on dry and time-reduced testing."

Jan 1, 2017

By Nadir Ansari, Brian W. Wilson, Marina S. W. Li

"A hybrid Deep Mixing (DM) shoring system was recently constructed for a high-rise development in downtown Vancouver, British Columbia, Canada for the temporary support of a five-level basement excavation. The site is bounded by an existing bridge off-ramp structure along its longest side and by city streets on the other two sides, which formed a truncated triangle in plan. A conventional secant pile wall was installed along the longest side, about 380 ft (116 m) in length, of the site. Hybrid shoring walls (HSW) 1 and 2 were installed along two shorter sides with each being 235 to 246 ft (72 to 75 m) long. HSW 3 completed the excavation support system along the shortest side with a length of about 55 ft (17 m). Cutter soil mixing (CSM) was proposed by the excavation and shoring design-build team in lieu of conventional secant piling. CSM was the preferred method to construct the infill panels between soldier piles because of the speed at which the shoring system could be constructed in the variable fill, peat, wood waste and overburden. Design ConsiderationsTo minimize the impact on buried utilities along the outside perimeter of the excavation, the temporary shoring was designed to limit the lateral displacements to less than 0.8 in (20 mm). Factors taken into consideration for shoring design included the lateral earth pressures from the fill and native soils, groundwater pressures, temporary construction loads (e.g., crane or heavy plant/equipment), and permanent structural requirements. The subsurface conditions at this site typically consisted of fill (cohesive and granular), overlying peat and/or wood waste, overlying clayey silt to sandy silt, overlying weathered to dense to very dense clayey silt till to sandy silt till with silt layers. Localized, perched groundwater was observed within the fill, peat, wood waste and sandy silt layers above the dense till."

Jan 1, 2017

By T. Resende, J. Sismour

"Signs in underground mines are subject to variable airflow, which carries dust and moisture. Dust buildup reduces their visibility, hampering production efficiency and safety. Underground workers commonly must stop to clean signs in order to gauge their location, or find critical supplies or services. There are currently a variety of coating products, including dust and water repellants, available on the market that have the potential to reduce dust accumulation on sign surfaces. This paper describes a preliminary study to determine their effectiveness. The study involved a practical testing protocol using a trickle rock duster and samples cut from a clean, used road sign. Product effectiveness, under both dry and wet conditions, was evaluated based on photographic evidence by comparing changes in sign luminosity after a period of rock dust application. By analyzing the frequency of different pixel luminosities on the dust-covered samples, both uniformity of dust coverage and the total amount of accumulation was assessed. Results indicate that at least one product may reduce the amount of dust buildup on sign surfaces and increase visibility. INTRODUCTION In all underground mines, visibility of signage is critical. Signs inform miners of their location, direction toward escape routes, and location of supplies. Over time, sign surfaces can collect dust and can eventually become unreadable. The rate of dust accumulation on surfaces is often particularly high in coal mines, where both mining (e.g., cutting and drilling) and rock dusting activities can contribute significant amounts of dust to the airways. Several factors may contribute to dust buildup on sign surfaces. First, basic principles of fluid and particle flow are at play. When a fluid travels past a stationary surface, the velocity of the fluid at the surface boundary is zero. If a very small dust particle moving with air collides with a surface, it does not immediately fall off since the air velocity is zero at the sign surface. (This is the same reason that dust can collect on a rotating ceiling fan.) Further, once the collision occurs, other mechanisms may help keep the particle there – including friction that resists particle falling due to gravity, and adhesive forces due to humidity and/or static charges the particle and others already on the surface. Currently, the most common way to deal with reduced sign visibility due to dust buildup is for mine personnel (e.g., a compliance foreman, supply worker) to periodically clean sign surfaces – usually just by wiping them with a cloth. As a regular activity, this solution is inefficient; in cases of emergencies, it can also pose unnecessary risks. Application of an off-the-shelf coating to sign surfaces may represent a simple yet effective way to reduce the rate of dust accumulation. There are currently a variety of products on the market that may be suitable for this purpose, including dust and water repellants."

Jan 1, 2017

By J. O. Marsden, M. M. Botz

"Heap leaching is responsible for approximately 21 percent — 3.9 million metric tonnes — of copper production and 9 percent — 270 metric tonnes or 8.7 million ounces — of gold production worldwide. Given metal price assumptions of $2.25/lb for copper and $1,250/oz for gold, these portions of global production generate revenues of $19 billion and $11 billion, respectively. For heap leaching operations, small changes in metal extraction efficiency drive substantial changes in operating cash flow margins and affect project viability. Variances in actual metal production from budgetary forecast estimates can mean the difference between success (value creation) and failure (value destruction) for a heap leach project. Despite the importance of heap leaching for copper, gold and silver production worldwide, there are no clear standards or guidelines for developing heap leach metal production forecasts. There is considerable variation among copper and gold producers that apply heap leaching technology as to how such modeling and forecasting is applied at the operational level. There are a variety of different modeling approaches that can be utilized for this purpose. However, these vary in cost, complexity, time to implement, accuracy and credibility. This paper explores the options available for heap leach modeling, discusses the advantages and disadvantages of each approach, and provides guidelines/recommendations for an effective approach to modeling metal production at existing or planned heap leach operations. The paper also provides expected ranges of variation between actual and modeled production.Introduction and backgroundHeap leaching is fundamentally different from other methods used in the processing and extraction of gold, silver, and copper and other base metals. Considered globally, the technique represents a relatively modest portion of production compared with the primary technologies applied for copper and gold recovery. Approximately 21 percent of copper production is attributable to heap leaching techniques, as opposed to 79 percent by conventional crushing, milling, flotation, smelting and refining. For gold, about 9 percent of global production is obtained from heap leaching, compared with over 90 percent by various combinations of crushing, milling, gravity concentration, flotation and/or agitated cyanide leaching processes or, in the case of placer deposits, by direct gravity concentration and/or amalgamation. In cases where heap leaching is the primary source of metal production, the ability to accurately forecast metal production may be the difference between commercial success and failure for a project or operation. Heap leaching — of crushed or run-of-mine ore — is also commonly applied as a secondary process to treat lower-grade ores from a given deposit, such as at Chuquicamata in Chile, Cerro Verde in Peru and Bagdad in Arizona for copper extraction and at Twin Creeks and Carlin, both in Nevada, for gold. In such cases, heap leaching provides incremental revenue to supplement the primary process. Variances between actual and forecast metal production from heap leaching as a secondary process are typically tolerated and absorbed within the overall site metallurgical balance. In either case, accurate production modeling and forecasting creates significant value for heap leaching projects, is essential for managing production expectations — timing and volumes — and is likely to be a critical success factor for most heap leach projects."

Jan 1, 2017

By K. L. Boyd

"Can the ever-increasing tonnages of ore and waste being mined today be accommodated simply by using bigger and better crushers? This paper reviews the latest primary crushing and large cone crusher designs. It highlights how—in addition to using the larger crushers now available—maximizing the utilization percentages in each of the four stages of the rock size reduction circuit will assist in meeting the larger production requirements of existing and new mining operations. Its goal is to help consultants and operators select the optimal equipment and custom-designed items in the material handling flowsheet from the mine to the mill, maximizing operating hours per year. INTRODUCTION Are larger crushers the answer to meeting the demands of existing or new mining projects for increased tonnage? Boyd (2002) predicted that larger crushers for primary and fine crushing would be beneficial and contribute to the further development of mineral processing. Larger crushers for primary and fine crushing applications are now available. The rock size reduction process from the mine to the selected milling process facility has not changed since man first broke a rock to get at the interesting mineralization within. The rock size reduction process circuit from the mine to the mill can be summarized in four stages: • Stage 1: Mining (rock breakage and fragmentation) • Stage 2: Pre-screening (scalping) • Stage 3: Primary crushing • Stage 4: Fine crushing (secondary, tertiary and quaternary) Plant throughput and ore delivery schedule will form the basis for flowsheet design and equipment selection. Once the project design criteria and the mine plan have been established, the circuit’s utilization percentage (percentage of hours when the circuit is being utilized) can be optimized for each of the four stages. The mining and process departments are the key stakeholders in the selection of the final comminution circuit, and both departments should be familiar with and contribute to the design of the circuit. This paper focuses on the four stages of a rock size reduction circuit from the mine to the mill, equipment selection, various ore and waste handling flowsheets, and improvements in crusher station design, all with the purpose of maximizing availability and plant utilization percentages. What is a large tonnage? From 1907 to 1914, the American Panama Canal excavated 300 million tonnes of material in 7 years (History of the Panama Canal, Wikipedia). Today’s large mining operations can move the same material in 10 months, using large crushers or multiple crushers for ore processing and large crushers and a mixture of truck haulage and conveyors for handling the large waste tonnages. Some examples include:"

Jan 1, 2017

By C. Xiao, F. Mohamm, A. Borsoi

"Nitrogen compounds produced by cyanide destruction and/or blasting are often a cause of concern for environmental compliance and at times, for water re-use in metallurgical circuits. Natural attenuation in tailings ponds and wetlands is not always sufficient to ensure compliance and/or achievement of overall water management objectives. This paper provides a general overview of active treatment methods for nitrogen management followed by an investigation of selective adsorption combined with electro-oxidation as the potential treatment method for thiocyanate. Results from bench scale treatability study are presented. The concept of holistic assessment of nitrogen management at mine sites using Risk Adjusted Life Cycle Cost is introduced and discussed in the context of gold mining operations using sodium cyanide.INTRODUCTION Unlike metals, nitrogen compounds present in mine waters originate entirely from anthropogenic sources rather than mineral deposits. Table 1 summarizes the main sources of nitrogen compounds reporting to mine wastewater.The best management practice related to the use of ANFO involves minimizing contact between ANFO and water, control and monitoring of blasting to reduce the occurrence of misfires, and reducing the consumption of blasting reagents for a given ore body. The most common practice for the management of NaCN is the incorporation of cyanide destruction in the metallurgical flowsheet and the use of tailings impoundments and holding ponds for natural attenuation of cyanide destruction residues such as NH4-N and CNO. At most mine sites there is no active management of NO3-N and SCN in wastewater. While current practices have produced satisfactory results, new enhanced methods to manage nitrogen compounds at mines are needed due to: 1) Increased scrutiny over the adverse effects of nitrogen compounds released into the environment; 2) New effluent standards; and 3) The shift away from wet tailings towards dry stack systems resulting in diminished natural attenuation and dilution of nitrogen residues prior to effluent discharge or water re-use in mineral processing."

Jan 1, 2017

By L. Sandbak

"CURRENT BASIS OF GROUND SUPPORT DESIGN ANALYSIS The current strategy used in determining what kinds of support are needed is based on empirical design charts (Grimstad and Barton, 1993). Figure 1 is an example of the topcut analysis used for a 14 foot wide (4.3 meter) drift, which is the current design width used for topcuts at TRJV mine. The majority of our topcuts are situated in ore of the Type IV and Type III weak rock class categories that necessitate the use of bolts, mesh and 2”-4” of shotcrete. This type of empirical chart gives excellent guidelines for the kinds of support, and it is based on case histories of civil tunneling and mining properties. It is a good starting point for determining the kinds of support needed, but not to the detail needed to optimize the number of bolts, type of mesh, or combination of types or strengths of shotcrete. This report is an attempt to help quantify the safety factor and optimum design parameters to include mesh and shotcrete as part of the design criteria and subsequent safety factor.SAFETY FACTOR ANALYSIS: BOLTS ONLY One type of safety factor analysis used at TRJV for the past 7 years is described as the “dead weight” method, developed by Pakalnis (2008). It involves the support of a conservative “dead weight” of rock held in place by bolts in which the depth of failure is approximated as a wedge whose height is one-half of the span. The failure or dead weight wedge resembles a triangular wedge that must be supported by the remainder of the bolts going through the wedge (see Figure 2).The support capacity of the system is determined by the bond strength of the bolts holding up the wedge, which is in turn based on the RMR. The method assumes the total support capacity is the sum of the individual bolt values defined by either the breaking strength or the bond strength of the bolts (whichever is lower) passing through the failure surface."

Jan 1, 2017

By Schoeman L., K. C. Sole

Evaluation and measurement of the influence of changes in conditions and electrolyte composition during early stages of a growing metal electrodeposit are crucial to predict changes in developing morphology. A galvanodynamic polarization technique was developed to reliably measure overpotentials for nickel electrodeposition from sulfate electrolyte. The validity of these polarization parameters as indicators of the relationships between changes in the electrolyte and resulting deposit morphology was evaluated for electrolytes of varying composition. Findings indicate that nucleation and plating overpotentials measured by the described technique can be used as indicative tools for monitoring, evaluating and ultimately improving control of the electrodeposition of nickel from sulfate electrolytes. The results predict that nickel deposits of desirable quality and morphology are obtained when plating overpotentials are higher than 700 mV vs. Ag/AgCl and nucleation overpotential is less negative than plating overpotential.

Jan 1, 2017

By J. F. Burr, D. Snyder, W. Calder

"INTRODUCTION “Explosion protection” refers to techniques used to minimize the potential for electrical and electronic equipment to create an ignition while operating in a hazardous location (HAZLOC). In particular, U.S. coal mines are required to use equipment in certain areas of the mine that has been approved by the Mine Safety and Health Administration (MSHA) for use in a methane and coal dust environment to limit the risk of the equipment creating an ignition-capable spark or a thermal energy ignition. In general, MSHA’s regulations for explosion protection recognize two techniques: the use of explosion-proof enclosures (XP boxes) and 2-fault intrinsic safety for electrical and electronic equipment. For 2-fault intrinsically safe (IS) equipment, the U.S. mining industry requirements are unique in that the equipment is certified by MSHA. The criteria MSHA uses to evaluate equipment for intrinsic safety, as required by Title 30 of the Code of Federal Regulations (30 CFR) [30 CFR, Sections18.20(b), 18.68(a)(1), 19.1(b), 20.1(c)(2), 22.6, 23.6, and 27.20(a)], is published in a document referred to as ACRI2001 (1). Outside of U.S. underground mining, many industries and countries accept equipment that is designed to a consensus-based international standard (ANSI/ISA 60079-11 is the U.S. version). The purpose of this study is to provide an overall assessment of the ANSI/ISA 60079-11 standard on 2-fault intrinsic safety and the MSHA ACRI2001 acceptance criteria, and determine if the ANSI/ISA document can be an alternative to ACRI2001 while maintaining an equivalent or better level of safety for miners. There are many drivers for this study. First, immediately after the 2006 MINER Act (2) was passed, there was a perception in the industry that the unique MSHA requirements were contributing to delays or restricting the availability of equipment to meet the requirements of the Act. Additionally, the MINER Act required that mine operators submit an accident response plan for MSHA approval, to be reviewed every six months. MSHA is required to determine if these plans reflect the most recent credible scientific research and make use of currently commercially available technology. There is a concern, as expressed in a recent National Academy of Science (NAS) study (3), that the unique requirements for U.S. mining may be limiting the technologies available to coal miners and technology options for mine operators. Accordingly, the study recommended that the National Institute for Occupational Safety and Health (NIOSH) and MSHA re-examine their technology approval and certification processes to ensure they are not deterring innovation, and explore opportunities to cooperate with other international approval organizations to harmonize U.S. and international standards without compromising safety. Lastly, the National Technology Transfer Act (NTTA) and the accompanying Office of Management and Budget’s OMB-119 circular mandate the use of consensus-based standards by federal agencies. However, for U.S. mining operations, MSHA cannot accept such standards unless a determination is made that such standards provide an equivalent level of protection for the miner, per the requirements of the 1977 Mine Act, the 2006 MINER Act, and 30 CFR Part 18 regulations."

Jan 1, 2017

By Sanket Rawat, Ravi Kant Mittal, Vikash Prasad

"The understanding of the response of pile foundations under various types of loads is a necessary prerequisite to analyze and design them properly. Therefore, this paper highlights and compares the provisions available in Indian Standard IS 2911:2010 to estimate the capacity of laterally loaded pile foundation with the provisions available in different country codes and existing literature. Comparisons are made between the Indian standard method, Broms method and Matlock & Reese method for the analysis of laterally loaded piles due to popularity and prevalence of the later methods in design offices worldwide. This has been achieved using a parametric study on pile embedded in pre-consolidated clay and sand for both fixed head and free head case in terms of displacement and ultimate load capacity. It has been found that there are various limitations to the Indian Standard method associated with various cases such as short pile analysis, complete moment distribution etc. Therefore, suitable recommendations have been made on the basis of the above comparison to improve the accuracy of the design in Indian perspective. The proposed comparison and subsequent area of improvements will present the design engineers all across the globe, a broad sight of design specifications of laterally loaded piles.INTRODUCTIONPiles in groups are very often subjected to both axial and lateral loads. In the 1960’s, designers used to assume that the piles could carry only axial loads and the lateral load is to be carried by batter piles. However, later, a large number of load tests authenticated that vertical piles also can transfer lateral loads through shear, bending, and lateral soil resistance rather than purely acting as axially loaded members. Initial attempts to analyze laterally loaded piles used the finite-difference method, as described by Howe (1955), Matlock and Reese (1960), and Bowles (1968). Matlock and Reese (1956) used the finite difference method to get a series of non-dimensional curves to enable the user to input the appropriate curve with the given lateral load and estimate the ground-line deflection and maximum bending moment in the pile shaft. Later, Matlock and Reese (1960) extended the earlier curves to include selected variations of soil modulus with depth."

Jan 1, 2017

By Andrew Moran, William H. Walton, Matthew D. Emrick, Mary C. Nodine

"A rapidly growing company in the northern US needed a large auditorium built into a dolomite bedrock hillside. The structure required an 80-foot-deep earth retention system independent of the auditorium foundation and superstructure. Allowable wall movements were limited to less than two inches. A 60-foot-tall permanent shotcreted soil and rock nail wall was designed for excavation support. The soil and rock nail wall utilized both active (post-tensioned) and passive nails, with capacities and installation angles optimized to address varying soil and rock conditions and to support heavy surcharges. The wall was configured with three two-foot-wide benches to facilitate controlled blasting and removal of more than two million cubic yards of soil, limestone and dolomite bedrock, and featured a permanent cast-in-place concrete face and a robust waterproofing and drainage system. A 20-foot-high reinforced concrete retaining wall was required at the top of the soil and rock nail wall to raise grades, resulting in a large surcharge.Design of the soil and rock nail wall was initiated less than three months before the start of construction, requiring expedited geotechnical explorations, analyses, design, and construction that would occur simultaneously. Design changes were made to address the discovery of a weak clay residuum seam at depth running along the base of the excavation, as well as significant changes to the building footprint made after the start of construction. Extensive performance monitoring was conducted during construction to measure vibrations and movements.Introduction and Project BackgroundA fast-growing company in the northern United States had a need for 600,000 square foot, 11,000 seat auditorium as part of its campus expansion. The auditorium was built underground, into a hillside to preserve the views of rolling terrain and farmland beyond. It featured a green roof and rockwork facing that mimicked regional geologic formations. The sixstory building required up to 80 feet of earth retention, including 60 feet of excavation beneath existing grades.As concepts for the project evolved, it became apparent that due to the geologic conditions, space limitations on site and the depth of cut required, a standard counterfort wall system would not be feasible. With groundbreaking for the building three months away, Thornton Tomasetti (structural engineer) engaged GEI Consultants, Inc. (wall design engineer) to design a 1,600-foot-long permanent soil and rock nail wall to support the excavation. The wall design engineer implemented a geotechnical exploration program immediately and began the design process, coordinating closely with Nicholson Construction (specialty"

Jan 1, 2017

By T. Kerr, C. Mattich, J. Wilson

"In refractory gold concentrates, gold is occluded in sulphide minerals preventing efficient cyanide leaching. Hence, roasting is used to oxidize sulphur and organic carbon, the latter being necessary to minimize recovery loss through the preg-robbing effect. In 2009, Outotec commissioned the circulating fluidized bed roaster at Syama gold mine in Mali. Since 2013 Resolute and Outotec have been implementing improvements to the roaster performance with the capacity increasing from 8000 t/month in 2013 to above 13,000 t/month in 2016, while achieving a residual sulphide sulphur and organic carbon contents of below 0.1 wt.% and 0.4 wt.%, respectively. Thus a gold recovery in the CIL of above 90% is attained. In 2016, Outotec audited the Syama roaster. The analysis resulted in the Low Carbon Roaster (LCR) upgrade concept which (i) allows re-processing of calcine dust from the spray cooler and ESP after pelletization and (ii) allows the roasting of a further fine-organic carbon rich feed, i.e. de-slime circuit tailings. The LCR upgrade aims to reduce organic carbon to <0.2 wt.% and increase roaster-leaching gold recovery by >3%. Project development included extensive testwork. The LCR process is expected to become operational during FY 2019.INTRODUCTION Double refractory sulphide ores exhibit the characteristics of gold locked within pyrite grains, in the presence of preg-robbing natural (organic) carbon. Hence, to achieve high recovery during subsequent processing steps, i.e. cyanide leaching, oxidation of sulphide sulphur is required, producing a porous calcine by way of a roasting step. This allows for the gold contained within the pyrite grains to be accessible during cyanide leaching. Furthermore, it is necessary to oxidize the organic carbon. Oxidizing the organic carbon is essential as gold recovery loss occurs as a result of gold-cyanide complexes being adsorbed on organic carbon, this phenomenon is termed as preg-robbing (Miller et al., 2016). The gold absorbed on the organic carbon is lost, reporting to the tailings stream. Hence, the aforementioned oxidation of sulphide sulphur and organic carbon is the process goal. Nonetheless, the latter must occur at a controlled temperature which is concentrate/ ore specific, since the pores of the produced calcine should not sinter, as this makes the gold contained in the calcine less accessible during leaching, leading to gold recovery loss. The tight temperature control requirement is a decisive factor in the choice of a Circulating Fluidized Bed (CFB) as the roasting reactor, due to the excellent mixing characteristics of the CFB which results in temperature homogeneity of (+/-10°C). Roasting of double refractory ores, as described above, can be included in the flowsheet after comminution and grinding, a process termed as whole ore roasting, or by including a flotation circuit termed as concentrate roasting. Roasting the flotation concentrate results in less solid flow, increased sulphide sulphur grade and organic carbon content resulting in a higher heating value and higher gold content. A typical composition of the Syama ore and concentrate is given in Table 1. Ore average values presented correspond to the period 2015, while concentrate values are typical for the flotation performance throughout the period 2012–2015."

Jan 1, 2017

By S. Renslow, G. Wang, L. R. Moore, Y. Xiong, J. Gu

"Clays are known to contribute to a wide range of mineral processing challenges. These challenges can haunt a plant from the pit, through the beneficiation plant and even to the tailings pond and process water. Each step that the clay is present potentially experiences significant and costly impacts to the process efficiencies. The effect of clay minerals on the performance of phosphate flotation was investigated. The investigation led to an understanding of the movement of clay through the beneficiation plant, the impact on reagent usage, and the overall flotation performance. INTRODUCTION With the decline in mineral feed grades, mineral processing will continue to face challenges. One significant challenge would be obtaining high recoveries of industry specified quality mineral concentrates with lower quality raw minerals. Other challenges may be the handling of the excess tails and process water being produced to maintain a mill’s production volumes. For example, increased levels of clay have been, and will continue to be, a topic of concern for many mines. Some of these concerns include environmental regulations associated with water storage and discharge, as well as beneficiation. Gonglun Chen reported that clays produced in the phosphate industry are generally colloidal and fine (90% < 45 µm) (Chen, 2006). As such, these clays can take 20-30 years to settle, in the absence of polymeric assistance. The settling of these clays is essential as an accidental discharge can lead to substantial impacts to the wildlife and ecosystem. The Environmental Protection Agency (EPA) has referenced cases where the discharge of water can result in fines in the tens of millions of dollars, and at times causing the processing plants shut down, depending on the volume and quality of this discharged water (EPA, 1997). The turbidity discharge criteria will vary from state to state. Florida’s Department of Environmental Protection has listed a turbidity maximum of 29 NTUs, or 60 mg/L total suspended solids, above the natural background condition (Florida Department of Environmental Protection, 2016). A lot of the literature has been focused on the impact of high levels of clay (>10%) on mineral processing. Farrokhpay has reported the significant impact of clay minerals on froth stability in copper flotation (Farrokhpay, 2012). He reported that clays can form a hydrophobic slime coating on the surface of bubbles, which can yield an increase in froth stability. Clay concentrations as low as 5% can have significant impacts on the rheological properties or slurry viscosities. Increased slurry viscosities can lead to either elevated pumping/processing energies being required, decrease in flotation efficiencies due to a decrease in bubble mobility through the pulp, or decreased throughput to manage these viscosities (Tu, 2005; Farrokhpay, 2013; Burdukova, 2014)."

Jan 1, 2017

By M. Gobla

"Since 1994 the Bureau of Reclamation has used risk analysis to evaluate dams. Risk considers both the likelihood of failure and the expected consequences should failure occur. Risk analysis relies on the detailed formulation and critical analysis of all possible potential failure modes. Potential failure modes are formulated by describing the sequence of events that must occur to result in failure, where failure is defined as the uncontrolled release of the impounded reservoir. Failure occurs in response to loadings such as water seepage through a dam (static forces), shaking from an earthquake (dynamic forces), sudden flood inflows (hydrologic forces), or accidental overfilling (operational errors). Reclamation has applied risk analysis methods to inactive and abandoned mines to evaluate tailings dams and flooded underground mines. Case histories of potential failure mode analysis as applied to mine impounded water illustrates what critical technical information is needed to determine if failure is likely, what the consequences of failure are likely to be, and what are the highest risks that should be addressed first. INTRODUCTION Impounded water, and high water content wastes, at mining and industrial processing sites are potential threats to public safety and the environment. Recent failures such as the TVA Kingston flyash impoundment failure in Tennessee in 2008 (5.4 million yd3 released), the Mt Poly Tailings Dam failure in British Columbia in 2014 (5.8 million yd3 released), and the Smarco Fundao Tailings Dam failure in Brazil in 2015 (78 million yd3 released) has renewed attention to this issue. Potential risks from impounded water at mining and industrial sites originates not only from tailing dams, but also from water in process ponds and conveyance pipelines, sediment retention dams, water retention dams, mine pit lakes, and flooded underground mine workings. Conventional water retaining dams also have a record of failure. Notable examples of failure include Vajont Dam in Italy in 1963 (2,600 lives lost), Banqiao and Shimantan Dams in China in 1975 (171,000 lives lost), and Machhu-II Dam in India (10,000 lives lost). After the 1976 Teton Dam failure in Idaho, the Bureau of Reclamation (BOR) established a Dam Safety Program. By 1984 the agency developed and began using risk analysis methods. Reclamation operates and maintains an inventory of hundreds of aging dams which were designed and constructed over a period of one hundred years. Many of these facilities were constructed using engineering design and construction methods which would not be considered good practice according to present day standards. Diligent observational monitoring, detailed site investigations, and the application of risk evaluation to the BOR dam inventory has identified many deficiencies resulting in significant demands on available funding for remediation efforts. The application of risk analysis has allowed the agency to rank sites by risk. By giving priority of remedial efforts to high risk sites, significant improvements to dam safety have been achieved. BOR has also applied risk analysis to evaluate and reclaim inactive and abandoned mining and industrial sites. The application of risk analysis methods in the mining industry is not new, the methodology was transferred to the mining industry more than 15 years ago as discussed in ICOLD Bulleting 121 (ICOLD, 2001), yet failures persist. This paper is meant to convey the lessons learned from BOR’s use of risk analyses in its work on mine sites."

Jan 1, 2017

By W. V. Liu, D. Omane, H. Yu, Y. Pourrahimian

"A large-scale wildfire had broken out at Fort McMurray in Alberta, Canada during May 2016. Many oil sands mining activities were affected due to the wildfire and the associated ash emissions. In particular, ash emission generated from the fire outbreak is a huge problem during the post-fire cleanup. These emissions pose a severe health hazard to workers, environment, and global climate. The ashes emitted into the atmosphere are caused by either human activities or climate conditions. The objective of this research is to assess the effect of three different ash dust suppressants, namely water, #1 surfactants, and #2 polymers at various volumetric concentrations on ashes samples to prevent propagation of fine solid emissions into the atmosphere. It is found that both #1 surfactants solution and #2 polymers solution are effective in retaining fugitive ash dust generated from the ashes. Volumetric concentration efficiency of 0.05% of #1 surfactant and 5% of #2 polymers in 500 ml of water have been proven to provide ash dust retention efficiency greater than 99% after the spraying of these suppressants. It is also found that both #1 surfactants solution and #2 polymers solution maintain an ash dust retention efficiency higher than that of the use of only water. This confirms the merit of using chemical dust suppressants on fugitive ash dust for a longer period, which is proven by the 72-hour data from this experiment. This study gives a general view of how effective chemical suppressants on fugitive ash emissions work. INTRODUCTION On May 1st, 2016, a large-scale wildfire gutted Fort McMurray, Alberta, Canada. Many oil sands mining activities were affected due to the wildfire and the associated ash emission. Due to the wildfire, some of the biggest oil sands companies in Fort McMurray such as Royal Dutch Shell and Suncor Energy shut down their oil production, at 255,000 and 350,000 barrels per day respectively [1]. Syncrude Canada Ltd scaled down its normal production capacity level of 350,000 barrels per day [1]. This generated an estimated loss of about 1.1 million barrels of oil production per day, constituting a 30% reduction in the Canadian daily oil production, crippling the economy [2]. This loss in production by the companies translated into 0.33 % of the Alberta GDP in 2016 constituting a loss of $985 million and 0.06 % of the entire Canadian economy [3]. In 2017, it is estimated that the rebuilding and reclamation of the affected areas in Fort McMurray will add $ 1.3 billion in GDP to Alberta’s economy [3]. A population of over 90,000 people was evacuated from the location and its surroundings for health and safety reasons [4]. The fire destroyed about 2,400 structures and over 500,000 hectares of forest vegetation in Fort McMurray, leaving an estimated 232,000 tonne of post-fire ashes [5,6]."

Jan 1, 2017

By Toru Yamasaki

"Bimodal lithostratigrafic assemblages are of significance in volcanogenic massive sulfide (VMS)-hosted lithology. The largest deposits are either bimodal-siliciclastic or maficsiliciclastic, and the presence of a significant siliciclastic component in the host stratigraphic succession favors large VMS deposits (e.g., Franklin et al., 2005; Barrie and Hannington, 1999). In the case of modern sub-seafloor VMS deposits in arc-related settings, the majority of deposits have been discovered in association with calderas or cauldrons (Halbach et al., 1993; Ishibashi and Urabe, 1995; Iizasa et al., 1999). These features are formed by the explosive eruption of silicic volcanoes, so that silicic host rocks and/or pumiceous volcanic clasts are generally observed around the ore deposits (e.g., Binns and Scott, 1993; Fiske et al., 2001). Caldera-like and graben-like morphological features therefore attract attention in geophysical surveys. However, silicic lithologies (dacite and rhyolite) normally contain only small amount of metallic elements (e.g., a few ppm to a few dozen ppm of Cu), whereas mafic rocks, such as basalts and basaltic andesites, contain significant amounts of metals (e.g., a few hundred ppm of Cu). Thus, the origin of metallic elements in VMS deposits associate with the silicic host rock remains unclear.The Iheya North Knoll is a volcanic complex in the middle of the Okinawa Trough. It is located in a young and actively spreading back-arc basin that extends for 1200 km behind the Ryukyu arc-trench system (Lee et al., 1980; Letouzey and Kimura, 1986). Several active hydrothermal fields have been recognized in the Iheya North Knoll. Mineralization at the Iheya North Knoll is characterized by relatively juvenile features consisting of VMS deposits with associated hydrothermal alterations to various degrees. Massive sphaleriterich sulfides at this site, recovered for the first time from beneath an active seafloor hydrothermal system, strongly resemble the black ore of the Kuroko deposits of the Miocene age in Japan (Takai et al., 2011). From February 11 to March 17, 2016, the SIP CK16-01 (Exp. 908) D/V Chikyu cruise was conducted at Iheya North Knoll and the rifting center of the Iheya Minor Ridge area, middle Okinawa Trough. The Iheya Minor Ridge area is also an active hydrothermal field, located ~30 km southeast of the Iheya North Knoll. In this area, basaltic rocks are widely distributed, and drilling has confirmed that the basaltic materials continue to ~120 m below the seafloor (Kumagai et al., in prep)."

Jan 1, 2017

By J. N. Van der Merwe

"Platinum is a highly valuable resource, its safe and economic extraction is paramount. The success of platinum mining by the bord and pillar method depends heavily on a comprehensive and dependable pillar design method. Pillars need to be large enough to safely support the load and small enough to avoid loss of resources. A critical evaluation of current pillar design systems used in narrow-reef platinum mining was undertaken using practical experience from a large feasibility-stage platinum exploration project, supplemented by observations from several platinum mines in Zimbabwe. An extensive literature survey was undertaken in order to determine the current status of design systems. Through this approach, the shortcomings of current pillar design systems are highlighted. Areas are proposed for further research to obtain a better understanding on how additional factors influence pillar system stability. The exploration work highlighted how rock mass classification methods can be utilized in determining the overall strength of pillars. Current pillar design systems for narrow-reef platinum mining consider width-to-heightratio (usually with different exponents for width and height) and the strength of the pillar material. However, there are many more important factors that are not considered and which have a bearing on pillar system stability. An in-depth study of these parameters with a view to establish effective narrow- reef platinum mining pillar design systems needs to be undertaken. IntroductionPillars have been used as a means of support since the early days of mining. Pillarsupported mining methods such as bord and pillar require a reliable design system for them to be successful. This paper presents an evaluation of the current hard-rock mining pillar design systems as applied to a practical large-scale narrow-reef platinum mining feasibility study. It is vital to have a dependable pillar design system for economic and sustainable mining. Using an extensive database collected from the project, the pillar strength formulae were tested and several discrepancies noted. This necessitates the establishment of more reliable pillar design systems. In narrow-reef platinum mining, large compressive stresses accompanied by geological and geotechnical factors contribute to pillar instability. A well-formulated pillar design system is required that accounts for such factors so as to minimize pillar failures."

Jan 1, 2017

By Tara Schenk-McFarland, Mark Bliss

Echo Dam, located near Coalville, Utah, is a facility that provides storage for irrigation and municipal use. Original construction of the dam was completed in 1931. Because of seismic concerns, the spillway crest structure and upper chute section, founded on old landslide and colluvial material, were recently replaced. Prior to replacement of these structures, jet grouting of a block of the loose and potentially liquefiable soils, directly beneath the spillway crest structure was selected as the preferred alternative to address the potential for settlement and cracking of the spillway crest structure. The replacement or alteration of the in-place soil reduces the likelihood of seismic-induced excess pore pressure development and subsequent settlements. Core drilling and sample recovery of the production jet grouted columns was completed to verify compliance with the specifications. It was recognized that due to the larger rock sizes within the deposits that full homogeneity of the jet grouted zone was unlikely to be achievable. However, the purpose of this jet grouted section was to strengthen enough of the soil so that widespread liquefaction does not occur. During the jet grouting production many instances of ground fracturing occurred. Fracturing was evident based on grout/air bubbles exiting the surface near some of the grout holes during jet grouting, air bubbles appearing in the spoil pits, and lifting of the ground surface in the vicinity of the monitor during the jet grouting process while the system was pressurized. In one instance, a section of the upstream spillway slab, which was left in place, was cracked due to pressurized grout escaping beneath the slab. The overall results of the jet grouting were satisfactory despite difficulties encountered. The cause of the fracturing is hypothesized and a recommendation is included to reduce the likelihood of this occurring on future jobs.

Jan 1, 2017