Search Documents

By M. R. Shahan, W. R. Reed, S. Klima, T. W. Beck

"Testing was conducted to determine the ability of foam to maintain roof coverage in a simulated longwall mining environment. Approximately 27% of the respirable coal mine dust can be attributed to longwall shield movement. Developing controls for this dust source has been difficult. The application of foam is a possible dust control method for this source. Laboratory testing of two foam agents was conducted to determine their ability of foam to adhere to a simulated longwall face roof surface. Two different foam generation methods were used; compressed air (CA) and blower air (BA). Using a new imaging technology, image processing and analysis utilizing ImageJ software produced quantifiable results of foam roof coverage. For CA foam in 3.3 m/s (3.3 m/s (650 fpm)) ventilation at 3 minutes after application, 98% of agent A was intact, while 95% of agent B was intact on the roof. At 30 minutes after application 94% of agent A was intact while only 20% of agent B remained. For BA in 3.3 m/s (3.3 m/s (650 fpm)) ventilation, the results were dependent upon nozzle type. Three different nozzles were tested. At 30 minutes after application 74-92% of foam agent A remained, while 3-50% of foam agent B remained. CA foam seems to remain intact for longer durations and is easier to apply than BA foam. However, more water drained from the foam when using CA foam which demonstrates that BA foam retains more water at the roof surface. Agent A seemed to be the better performer as far as roof application is concerned. This testing demonstrates that roof application of foam is feasible and is able withstand a typical face ventilation velocity, establishing this technique’s potential for longwall shield dust control. INTRODUCTION NIOSH personnel have visited many longwall operations at various geographical locations in the U.S., conducting benchmark surveys to characterize current operating practices and dust control measures in use. Sources of respirable dust generated from the longwall face have been identified as: intake (10%), stage loader (20%), shields (27%), and shearer (43%) [1]. Dust generated from the shearer, armored face conveyor, and the stage loader can mainly be controlled by water sprays and increases in ventilation air quantities, however, research has demonstrated limited effective controls for dusts generated by shield movements [2]. One possible approach to mitigating shield dust generation is to apply a layer of water or foam to the shield-roof interface. Once this interface is blanketed with foam or water, dust will be less likely to become airborne and contaminate the airways over the personnel walkways. Though water is an abundant and common dust control measure, roof applications have limited success because water is unable to remain in-place in adequate quantities for the necessary duration between application and shield advance. Past and current testing of foam for material properties has shown that it has longer applicability times, ranging from 10 to 60 minutes [3] and has shown better performance for dust control, ranging from 19-96% improved efficiency over water [4, 5, 6, 7, 8]. The majority of this foam dust control research has focused on dust control efficiency at the longwall shearer or continuous miner cutting drum."

Jan 1, 2017

By Türker Hüdaverdi, Özge Akyildiz

"Efficiency of blast operations depends on fragmentation, overbreak, muckpile profile anddisplacement, vibration, airblast, flyrock and damage to wall or slope stability. To provide all these conditions at the optimal level, determination of rock mass properties (in-situ block size, joint spacing and orientation) is the very first step during design stage of rock blasting. Image analysis software is used not only to determine the fragmentation level of muckpile but also to characterize the bench face. In this study, an image analysis software was used to determine apparent block size of bench face and to measure blast fragmentation of muckpile. The source of errors and the vital points to be taken into consideration were explained for bench face characterization andfragmentation measurement. Since it provides much better results than previous techniques and it is not intrusive to production process, image analysis technique is considered as one of the most efficient and preferred way for fragmentation analysis. Besides these advantages, there are some weak points of image analysis software. Lighting is one of the most important factors for photographs captured for in-situ block size analysis and fragmentation analysis. Lighting determines shadow formation. In an ideal image, particles are clearly delineated by soft shadows. If shadows are too strong (dark), analysis suffers. Appropriate scale should be replaced onto blast muckpile during site measurements. The location of the scale in image affects the results of analysis. Also, the densityand orientation of discontinuities should be considered during application of image analysis technique to characterize bench faces. In this study, image analysis software was applied in thesandstone, limestone quarries of Istanbul region and an open pit boron mine. All image analysis, evaluations and results were made based on the site measurements."

Jan 1, 2017

By D. Warkentin, T. Yeomans, R. Tavakoli, A. Nacu

"One of the most successful commercial methods of extracting gold from ores involves solubilizing gold as a gold cyanide complex, followed by adsorption of the complex onto activated carbon. The gold cyanide is subsequently eluted from the carbon to produce a concentrated gold solution suitable for electrowinning to recover the precious metals. Stripped carbon is treated in a kiln under a flowing steam atmosphere to reactivate its surface, allowing it to be reused. The aim of this study was to investigate the gold elution using a mixture of sodium hydroxide and isopropyl alcohol in both batch and continuous tests, with the eluates being electrowon on carbon foam cathodes. The effects of various factors, including alcohol content and sodium cyanide addition were studied. The addition of alcohol considerably improved gold elution kinetics, while the presence of sodium cyanide did not have a significant impact on either elution efficiency or kinetics. In all cases, efficient electrolysis was shown to be an important factor in maintaining effective carbon circuit operation.INTRODUCTION Gold dissolved as Au(CN)2- complex during cyanidation is recovered either by cementation with zinc powder, also known as the Merrill-Crowe process, or by adsorption into activated carbon through Carbon-in-Pulp (CIP) or Carbon-in-Leach (CIL) processes. Activated carbon loaded with gold is then eluted and gold is subsequently recovered by electrochemical methods. Conventional elution processes such as atmospheric and pressurized Zadra processes, involve stripping with a cyanide (0.1–0.2% NaCN) and sodium hydroxide solution (1–2% NaOH) at high temperature (90–140°C) over long elution times of 8 to 72 hours. In the Anglo American Research Laboratories (ARL) elution process, the acid-washed loaded carbon is pretreated with a strong sodium cyanide and sodium hydroxide solution (1–5% NaCN and 1–2% NaOH), followed by elution with water at 110–130°C. Solvent-assisted elution processes have also been reported, such methods use varying concentrations of alcohols (methanol, ethanol and isopropanol), ketones, or glycols to enhance atmospheric elutions at temperatures up to 95°C (Muir et al., 1985; Ubaldini et al., 2006; Espiell et al., 2008; Soleimani & Kaghazchi, 2008). The present work investigates the efficiency of isopropanol in the gold elution process, as well as the methodology of evaluating gold stripping processes in the lab setting"

Jan 1, 2017

By D. M. Ziebarth

"During the mid to late 1960’s, the underground potash industry in Saskatchewan was born. For the next four decades the industry operated at a steady pace supporting a large part of the world demand; until 2008 when the potash market heightened. Operators were motivated to capitalize on this increased demand, new mines were proposed while existing mines were planning upgrades. Potash Corporation of Saskatchewan (PCS) was one of the major producers planning upgrades to their production facilities quickly, including modifying the existing headframe and shaft at the PCS Cory Site to accommodate a new 1500 tonne per hour hoisting plant. Upon completion of the project, the innovative operations group continuously reviewed methods to increase production and reduce operating costs, allowing PCS to continue being competitive on the world market. This paper will describe the design challenges encountered during the development of the infrastructure around an operating facility whilst minimizing down time, schedule, capital and construction costs. This paper will also explore the strategy to increase capacity of the newly commissioned hoisting plant. BACKGROUND Potash production is a major Saskatchewan industry, and has played a significant role in the economy for over 40 years. Production commenced in 1962 when water problems were overcome at the International Minerals and Chemical (IMC) mine near Esterhazy, Saskatchewan. A surge of development by other companies resulted in twelve companies opening ten mines by 1970. In 1975 Potash Corporation of Saskatchewan was created by the government of Saskatchewan and shortly thereafter purchased several mines in Saskatchewan, including the Cory Mine (Cory), near Saskatoon. Cory has been in operation since 1968 and is located 12 km (7.5 mi) west of Saskatoon in central Saskatchewan. The mine is located in the center of the world’s largest potash deposit, 1,000 m (3300 feet) below surface. PCS has embarked on sizable capital expansions of more than CDN $7 billion. The Cory CDN $1.6 billion expansion was expected to raise operational capability of the site to 2.7 million tonnes per year, an increase of 1.9 million tonnes per year (MTPY). To achieve 2.7 MTPY of finished product and considering the 22.6% average production recovery1, 12 MTPY of ore must be hoisted to surface for processing. To deliver this rate required upgrading of the hoisting plant to 1500 tonne per hour (TPH). To accomplish this ambitious challenge, creative thinking, careful planning and a cohesive team was needed to work together to ensure the schedule, budget and most importantly the work was completed safely"

Jan 1, 2017

By R. L. Bruening, R. M. Izatt, N. E. Izatt, S. R. Izatt

"Molecular Recognition Technology (MRT) is a simplified, green chemistry process with applications in selective separations of Ni(II), Co(II), and platinum group metals in primary ore beneficiation processes and secondary recovery operations from spent products, scrap, and environmental waste solutions. Simplification in MRT processes is achieved by non-use of solvents, reduced space requirements, and a simple separation system involving columns packed with metal-selective SuperLig® resins. Minimal waste is generated and metal recovery is achieved at 99% levels from g L-1 to <mg L-1 concentrations. MRT systems are attractive technologically and economically compared with solvent extraction, ion exchange, and precipitation separation processes. Commercial examples of MRT use include removal of impurity metals Cd, Cu, Ni. Fe, and Pb to mg L-1 or lower concentration levels from Co streams to produce battery-grade Co. Highly purified Co is required for optimal function of lithium ion rechargeable batteries and superalloys associated with aerospace and gas turbine operations. Impurity metals are recovered for reuse or proper disposal rather than being discarded to landfill. Green chemistry processes, such as MRT, are needed in metal separations going forward into the 21st century to achieve global metal sustainability in processing of native ore and treatment of secondary sources.INTRODUCTION Maximizing efficiencies of metal separations and optimizing metal recovery rates during separation processes are important goals on the road to achieving metal sustainability. Achievement of these goals is consistent with stated principles of green engineering (O'Connor, Zimmerman, Anastas, & Plata, 2016) and green chemistry (Anastas & Eghbali, 2010). Molecular Recognition Technology (MRT) separation processes using SuperLig® resins have a 25-year record of performing competitive, commercial metal separations with metal recovery rates approaching 100% (Izatt, Izatt, Izatt, Krakowiak, & Bruening, 2017). SuperLig® resins are characterized by high selectivities for specific metals over concentration ranges from g L-1 to mg L-1 or lower. MRT systems use no solvents and are simple in design and operation resulting in reduced capital and operating expenses."

Jan 1, 2017

By J. Y. Foley, K. Eden, A. E. Grosz, C. J. Giles, J. E. Grosz

"Portions of the Icy Cape placer Au district have been described and exploited since the early 1900s. Industrial studies of Au-bearing garnetrich intervals established a 3.5 million troy ounce resource in the western half of the district. This estimate is not compliant with CIM and SME definition standards for Mineral Resources and Mineral Reserves. We note high variability in the textures of sediments and their heavy mineral (HM) content and composition in the district, probably as a function of the depositional environment. Sediments are medium- to fine-grained sands with a valuable HM assemblage that averages 26.0% in a range of 1.1– 72.6%. Valuable heavy minerals (VHMs) garnet, magnetite, ilmenite, rutile, and zircon, but excluding Au, average 7.9% in a range of 1.0–37.6% of the HM assemblage. Trace quantities of uraninite, thorite, monazite, xenotime, and others are noted. Garnets have an average Y content of 726 ppm with a range of 0–2150 ppm. Energy-dispersive X-ray fluorescence confirms compositions commensurate with Ca, Al, and Mg silicates. We provide empirical analytical data and note high variability in the textures, HM content, and compositions as a probable function of depositional environment. Icy Cape District land and resources are owned by the Alaska Mental Health Trust Authority and managed by the Trust Land Office (TLO). IntroductionThe Icy Cape Heavy Minerals (HM) District in Alaska subtends more than 200 km2 fronting the Pacific Ocean and backing to the foot of the Robinson Mountains at about 1700 m above sea level. We classify the district into geomorphic provinces; the eastern region as deltaic (Figure 1) and the western region as coastal plain (Figure 2), based on geomorphologic expressions. The coastal plain is entirely built up of unconsolidated outwash sediments and ancient beach sand deposits."

Jan 1, 2017

By Steinar L. Ellefmo, Maxime Lesage

"There are many reasons invoked when discussing the relevance of deep-sea mining minerals. The shift towards more focus on renewable energy (“the green shift”) will not be possible without more materials coming from the mining industry. The increasing population, and thus increased number of consumers, will lead to an increase of the mineral demand. It has been established that recycling will not satisfy the need for more minerals by itself. Meanwhile, land mineral resources - such as copper – become every day more complex to extract. The question of the deep-sea minerals exploitation’s viability needs to be studied now. Within the framework of feasibility studies, various topics such as environment, technologies and operations management must be addressed. Recognising deep-sea mining as a hybrid activity - taking from the mining, maritime and the offshore oil and gas industries - it is deemed too complex for a global assessment. Each deep-sea mining environment is worth its separate study.Norway is recognised as a seafarer nation. Looking towards the sea and driven by the will to thrive on the Blue Economy, Norway decided to investigate the case for deep-sea minerals on its Extended Continental Shelf. The MarMine project is a materialisation of this endeavour. The Norwegian case will address its own particularities such as a respectable water depth, the arctic environment, the remoteness to shore support and an environmental aware population as well as subsequent policies."

Jan 1, 2017

By Peter Moser, Finn Ouchterlony, José A. Sanchidrián

"Blast fragmentation data in the form of percentile fragment sizes as function of specific charge oftenform a set of straight lines in log(size)-log(energy) space that tend to converge on a common focal point.Single-hole shots in specimens of virgin material clearly show this and the phenomenon is called the fragmentation-energy fan. Field data from bench blasting in rock scatter much more but may be interpreted to form such fans. The slopes values of the fan lines depend primarily on the percentile level. This property can be derived from sieving functions of the form P[ln(x/xmax)/ln(xmax/x50)]. An example is the Swebrec function when the parameter b is constant."

Jan 1, 2017

By T. W. Camm, J. C. Johnson

"Most engineers are bright, hard-working, reliable, and prefer to avoid conflict. An engineering curriculum tends to self-select these characteristics. By most standards, you would expect workers exhibiting these traits to require minimal supervision. But is this true? Is this how most current engineering managers lead? Looking at some current theories on leadership combined with personal anecdotes, this presentation will look at some common misconceptions about leading engineers. INTRODUCTION Engineers are different. There, I said it. From cartoons to movies to television shows and more, there is a reason stereotypes of engineers resonate. Yes, you can find a lot individual variation among specific engineers that you may know, but they do not detract from some of the overarching commonalities that engineers are known for. CLASH OF CULTURES What distinguishes a professional? Raelin (1985), in his book Clash of Cultures, describes professionals as having superior intellectual training, maintaining their own standards of excellence, and being supported by associations that maintain the quality of the profession. Engineers obviously fit all three of these ideas: an engineering degree is still regarded as one of the most difficult to attain; we maintain our own standards both through peer-review and in academia through ABET accreditation; and through professional associations like SME to promote the discipline and foster technical growth. Six characteristics representing professional status are described by Raelin (1985, p. 9): Expertise—prolonged specialized training in a body of abstract knowledge. Autonomy—the freedom to choose the means to solving a problem. Commitment—Primary interest is in pursuing the practice of one’s own chosen specialty. Identification—identifying with the profession and with fellow professionals, both through formal associations and through peers external to the organization. Ethics—providing service without concern for oneself or without becoming emotionally involved with the client. Standards—committed to help in policing the conduct of fellow professionals. Engineers are smart—in the vast majority of cases they are hired specifically for their expertise. At a typical mine the ventilation engineer knows more about mine ventilation than anyone else on site; the same is true for the rock mechanics engineer, the explosives engineer, the planning engineer who uses sophisticated computer software—each is the expert for their particular area at the mine, that is why they have that responsibility. This can present a dilemma for the manager for each (sometimes all) of these engineers. The manager needs to keep everyone on task and focused on the objectives of the organization. Because they have reached their position by following the norms and expectations of the organization, managers tend to have a certain amount of loyalty to that organization. Engineers, on the other hand, tend to have mixed loyalties, having as much loyalty and affinity for their profession as they do for the particular company they happen to be working for at any given time. This dynamic can often lead to power struggles between the managers, based on their positional authority in the organization, and the engineers, based on their specialized knowledge (Camm, 2013)."

Jan 1, 2017

By A. Navarra, C. Arrancibia, R. Yañez, C. Acuña, F. Valenzuela

"Discrete event simulation (DES) is a suitable framework to evaluate and optimize the dynamics of sulphide smelters. In particular, iron-nickel-copper-cobalt sulphides undergo continual oxidation within a roasting or smelting operation, followed by batch oxidation within the converting operation, thus producing iron-free Bessemer matte (or blister copper, in the case of copper smelters); this semi-finished product undergoes further processing to produce nickel, copper and cobalt products, and to recover precious metals. The juncture between continuous smelting and batch converting is often an appropriate focus for the earliest phases of DES development, since it is typically a major bottleneck within nickel and copper smelters; later phases may include increasing levels of detail for auxiliary unit operations, as well as plant logistics. Moreover, DES can support matte-slag chemistry, including Gibbs free energy balances to determine the iron speciation within the slag. DES is therefore capable of linking the fundamentals of oxidation reactions to the intricacies of plant dynamics.INTRODUCTION Discrete event simulation (DES) is gaining acceptance within the extractive metallurgy community, as a technique that quantifies the system-wide performance of metallurgical plants under conditions of uncertainty (Wheeler & McGinty, 2015). In particular, over 90% of smelters that process nickel-copper-cobalt sulphides and copper sulphides exhibit similar semi-continuous dynamics (Crundwell et al., 2011b; Schlesinger et al., 2011b), in which the converting aisle produces batches of material that are sent for further processing (Figure 1). Thus the tools and practices that are developed for a specific sulphide smelter are often relevant to numerous other smelters.The juncture between continuous smelting and batch converting has long been a focus for discrete event simulation (Welgama et al., 1996). Nonetheless, the broad acceptance of DES in nonferrous smelters has been hindered by interdisciplinary barriers that divide industrial and metallurgical engineers (Navarra et al., 2016; Noorossana et al., 2012); this divide has been less severe in steel plants (Hollocks, 2006). In recent years, DES has been used in copper smelters to analyze crane-and-ladle motions (Coursol et al., 2009a), reverts production and consumption (Noorossana et al., 2012), and innovative control systems (Herrera et al., 2016); additionally, DES models have accounted for shutdowns and random breakdowns to provide realistic assessments of copper smelter capacities, thus guiding equipment upgrades (Campbell et al., 2013; Coursol et al., 2009a). All of these studies feature a Peirce-Smith converting aisle similar to Figure 1 that, under normal operations, constrain the smelter throughput, and are thus a bottleneck (Campbell et al., 2013; Navarra et al., 2016)."

Jan 1, 2017

By M. Fig, J. Brune, C. Strebinger, G. Bogin, J. Grubb

"Although it is known that explosive gas zones can form and sustain combustion in a longwall coal mine gob, a complete account of the interaction of the methane flame and gob remains obscure. The goal of this study is to examine the impact of several gob parameters such as packing orientation and void spacing. The impact of ignition location is also detailed. A series of experiments with methane flames were performed in a horizontal cylindrical quartz reactor. The reactor was tested both empty and packed with an obstacle wall consisting of spherical glass beads to investigate the impact of various gob parameters. Results demonstrate that methane burning velocity is sensitive to all parameters investigated, and most sensitive to packing density and ignition location. INTRODUCTION The explosion at the Upper Big Branch Mine in 2010 and several other underground longwall coal mine fires and explosions show that explosive gases can mix with fresh ventilation air creating explosive gas zones (EGZs). Investigative reports of these fires have found that EGZs are able to move from the gob and into the active longwall face, endangering workers and equipment [1]. Currently, researchers at the Colorado School of Mines are using computation fluid dynamics (CFD) modeling to predict the location and movement of EGZs in the gob and along the longwall face [2,3]. It is the goal of this work to validate combustion models [4] that include interactions of the flame and the gob for future incorporation into ongoing CFD modeling of EGZs [2,3]. Throughout the years, there has been significant research investigating how flames interact with obstacles and propagate through porous media [4,5,7-11]. Since there is limited access to the gob in a longwall coal mine (Figure 1), the orientation and size of rocks and void spaces within the gob is unknown. Experiments of a simulated gob have been performed in a large scale flame tube in order to investigate the effect of scale (Figure 2) [4,5]. However, the variation in rock spacing, rock orientation, and void location makes it difficult to determine the impact of each of these parameters on methane flame dynamics. This study aims at gaining a stronger fundamental understanding of gob parameters such as spacing, orientation, and ignition location on methane flame propagation. The results from this study will provide a basis for experimentation in larger explosion vessels and will be used to validate methane combustion models for incorporation into longwall ventilation models of EGZ movement [2,3,4]. BACKGROUND Researchers have been studying flame propagation across obstacles and porous media for many years using various fuels and experimental setups [4,5,7-11]. Experiments have been performed in horizontal chambers with both ends open [7], horizontal chambers that are semi-open [4,11], horizontal chambers with both ends closed [8], and vertical arrangements [9,10]. Due to the variation in experimental setups and methods of characterizing flame dynamics such as flame speed, peak overpressure, or burning velocity it becomes difficult to directly compare results. Flame speed is a property of the mixture and refers to the speed of the unstretched flame front normal to the direction of propagation. This study characterizes the flame by its burning velocity, which is the difference between the flame speed and the speed of the unburned gases just ahead of the flame front. However, some references use the terms flame speed and burning velocity interchangeably. In this study, a semi-open quartz cylindrical reactor was used to determine methane burning velocity, which was used as a basis for comparison to determine the impact of obstacle configuration on methane flame dynamics. The quartz reactor also has the unique ability to allow for flame visualization. These features allow for faster combustion model validation [4]."

Jan 1, 2017

By K. Gardner

"Many deposits have a geological model developed early in the project stages, which is not always reviewed or modified as the project matures and production commences. Conversely, ongoing pressures, due to a combination of declining head grades, a push for increased revenue and a multitude of other reasons, leads to processing plant modifications, with the primary aim being to increase production. Often, the ore deposit knowledge is not sustained or developed during the operational stages to the level carried out during the prefeasibility and feasibility study phases. This results in the variability within the deposit being poorly understood and a lack of data and knowledge being available to support (and ideally optimise) operations particularly in an environment where the flow sheet has changed and ore feed requirements are complex.INTRODUCTION This paper presents a case study of ore deposit knowledge development and corresponding process plant operating strategy at the Ladolam Gold Deposit, commonly referred to as the Lihir gold deposit in Papua New Guinea. The gold deposit is located in a tropical equatorial climate on the east side of Lihir Island in the New Ireland Province of Papua New Guinea. Gold mineralisation was discovered in 1982, and was followed by a major exploration campaign by a joint venture between Kennecott (Rio Tinto) and Nuigini Mining Limited. The first drillhole was drilled in 1983, and after an extensive period of drilling consisting of 343 holes for 83,500 m, the final Feasibility Study was completed in 1992. The feasibility study was based on a Reserve base of 37.9 Moz in refractory sulphide ore, with gold extraction proposed to occur via whole ore pressure oxidation due to the refractory nature of the mineralisation. The Lihir Special Mining Lease (SML) was granted in 1995 to a new PNG company – Lihir Gold Limited, and Rio Tinto established Lihir Management Company to develop and operate the mine on behalf of LGL. Mining and processing of the deposit commenced in 1997. Newcrest Mining Limited purchased Lihir Gold Limited in August 2010, and subsequently completed a major plant upgrade including the installation of additional grinding, autoclave and carbon-in-leach capacity. Post commissioning of the upgrade, Newcrest has continued to increase throughput and production. A reinvigorated ore body knowledge development program has significantly assisted this process in identifying operating strategies for the process plant and delivering recovery improvement projects to address declining head grade and recovery due to increased stockpile feed and flotation circuit use."

Jan 1, 2017

By D. M. Maijer, S. L. Cockcroft, S. Modak, A. B. Phillion

"A comparison between hydrogen-diffusion-based micro-porosity formation and growth behaviour of two important aluminium foundry alloys, B206 (Al-Cu) and A356 (Al-Si-Mg) is presented in this paper. Specifically, the predicted pore size and pore fraction distribution of these two alloys resulting from directional solidification and identical hydrogen concentration are investigated numerically based on a model proposed by Yao et al. (2011. Met. & Mat. Tran. A. 42A, 4137–4148). This model takes into consideration the initial hydrogen content in the melt, the cooling rate, the partitioning of hydrogen between the solid and liquid phases, and the evolution in solid fraction with temperature. Due to different alloy chemistries, the activity of hydrogen in B206 and A356 are quite different, as are the solidification range and the resulting solidification microstructure. Being a primary alloy, B206 has dendritic microstructure and solidifies over nearly 135°C (505–641°C), whereas A356 contains fifty percent eutectic microstructure, and solidifies over 80°C (533–613°C). This allows a very different behaviour of micropores i.e. the effective pore radius in B206 is quite a bit lower as compared to A356, as is the pore number density. The evolution of local hydrogen concentration in liquid metal is analysed and compared for both the alloys.INTRODUCTION Over the past decades, the demand for materials with enhanced strength-to-weight ratios has significantly increased in the aerospace and automobile industries in order to improved fuel efficiency. For many automotive components, particularly shape castings, the trend is towards replacing ferrous alloys with aluminium alloys. The increase in the use of Al is primarily due to its low density, about one-third that of steel, and its relatively good strength that allows for weight reduction without reducing performance. Presently, Al-Si based alloys (e.g. A356) are the most prevalent due to their good mechanical performance in strength-to-weight ratio and excellent castability (Atwood et.al., 2000). However, superior mechanical properties can be achieved using Al-Cu alloys. For example, the alloy B206 offers a higher strength while retaining excellent ductility (Poirier et.al., 1987)."

Jan 1, 2017

By K. Horikawa, S. Kitahata, H. Kobayashi

"It has been clarified that the Al-5%Mg alloys containing 200 mass ppm of sodium showed grain boundary (GB) fracture, even when tested at room temperature, as well as at high temperatures (~500°C). SEM/EDX study revealed that the GB fracture was associated with the segregation of sodium on grain boundaries of the Al-Mg base alloys. Differential scanning calorimetry (DSC) revealed that the GB fracture at room temperature of Al-Mg alloys was caused by sodium segregation in the solid state. It was also shown that the tendency of the GB fracture strongly depended on the heat treatment; the alloys after the solution heat treatment showed severe GB fracture compared with the alloys after the homogenizing treatment. Moreover, it was shown that the GB fracture at room temperature by sodium segregation was suppressed by the addition of bismuth or indium. The suppression of the GB fracture by the additional elements was believed to be the scavenging effects by forming the sodium bearing compounds in grains.INTRODUCTIONIt is widely known that Al-Mg base alloys containing high amount of magnesium(~5 mass%)show better workability at room temperature, while that the alloys show grain boundary (GB) embrittlement at higher temperatures ranging from 200 to 500°C, depending on grain size(Otsuka, 1984), sodium impurity level(Ransley, 1959, Okada, 1997, Horikawa, 2001)and testing strain rate(Yamada, 2012). In the case of coarse-grained Al-5%Mg alloys (~300 ?m), 2 mass ppm of sodium causes severe GB fracture around 300°C, however, the Al-5%Mg-2ppm alloy does not show GB fracture at room temperature. It has also been shown that the GB embrittlement caused by 2ppm of sodium was suppressed by the additional elements, such as bismuth (Talbot, 1995), antimony (Ueda, 1997) and indium (Horikawa, 2012). Basedon these facts, we have concluded that the GB embrittlement at higher temperatures of Al-Mg alloys is attributed to the synergy effects of GB segregation of atomic sodium and GB sliding. For the GB embrittlement mechanism of Al-Mg alloys, involvement of low melting point metallic phases has been pointed out (Lynch, 2002),since the GB embrittlement appeared only at high temperatures. Up to date, the effects of high amount of sodium addition more than 2 ppm on GB fracture were not fully investigated in Al-Mg alloys. In the present study, the effect of 100 ppm ordered sodium impurity on GB fracture of Al-5%Mg alloys was examined, together with the effect of another additional elements."

Jan 1, 2017

By Takashi Sasaoka, Hiroshi Takamoto, Akihiro Hamanaka, Pongpanya Phnthoudeth, Hideki Shimada, Jiro Oya

"Indonesia is the second largest coal exporter to Japan, accounting for about 30 Mt annually. They produced over 400 Mt in 2015, over 99% of which is from open-cut mines. However, the conditions of surface mining are becoming worse year by year: the stripping ratio is increasing, the economy is worsening, and the infrastructure for coal transportation from inland mining areas is not being maintained. To meet the demand for coal in Indonesia and the rest of the world, underground mines have to be developed. In consideration of growing need, our research program is conducting a study on the potential for an underground coal mine in Indonesia. This research is being done through the roadway heading research program, which is looking into developing an underground coal mine from an open pit highwall. The greatest challenge for underground coal mine development in Indonesia is the maintaining the safety of the mine roadway during heading because the roof rock is exceptionally weaker. There is a potential for heading below mobile, unconsolidated soft sediment, and instead mining a deep area. This increases the likelihood for problems in the stability of the support system due to increasing ground pressure. The ground behavior around the roadway was measured using telltales, extensometers, and convergence measurements. Moreover, rock property tests were also conducted on exploration drilling cores. Based on the geological dates and monitoring data, a series of numerical analyses were conducted in order to assess support needs in the main roadway under different depths. Results of numerical analyses indicate that the current arch support design is effective when the mining depth is lower than 100m. However, if the mining depth is larger than 100m, the current arch support design should be changed to include the application of higher yield strength material, shorter spacing, etc. Moreover, bolting may also be useful if ground pressure is high locally. Based on a series of measurement data of ground and support behavior, a control criterion for main roadways under weak geological conditions is proposed in this paper."

Jan 1, 2017

By P. C. Santos-Munguía, F. Nava-Alonso, O. Alonso-González

"The gold recovery of a Mexican cyanidation plant, in Sonora, has been decreasing due to the increasing presence of gold tellurides. This work presents the results of different processes aimed to recover the remaining gold from the cyanidation tailings of the operation. The cyanidation in the mine is performed at 0.1 g/L NaCN and pH = 10.3, adjusted with lime. The treatments studied in the laboratory with these tailings were: cyanidation at higher cyanide concentration than that used in the plant, cyanidation with oxygen injection, cyanidation with oxygen and lead nitrate addition, and thiourea leaching. The results obtained with each of these treatments are presented and discussed with the final objective of proposing a method to recover the gold associated with tellurium.INTRODUCTION It has been demonstrated that gold telluride is refractory to the conventional cyanidation process and, for this reason, some alternative methods to recover precious metals from tellurides have been proposed. (Zhang et al., 2010). These include cyanidation with modified conditions or the use of non-cyanide leaching agents. This work presents the gold leaching results of tests performed with a sample of cyanidation tailings obtained from a Mexican deposit containing telluride species. The mine exploits a mesothermal deposit with a molar Te/Au ratio of 1, containing also lead, molybdenum, bismuth and tungsten. Gold is recovered from the ore by standard cyanidation, however, lately the gold recovery has decreased, likely due to the tellurium content of the ore. The sample used in this work was the cyanidation tailings of this deposit. It was treated in the plant by cyanide heap leaching (0.1 g/L NaCN, pH = 10.3 adjusted with lime). Some gold remained after the cyanidation and it was thought that this gold was associated with tellurium. The objective of this work was the recovery of the remaining gold from the tailings by an alternative process."

Jan 1, 2017

By A. David Miller, Chika Oya

"Field sampling and testing are part of the Quality Assurance/Quality Control (QA/QC) requirements for all Cement Deep Soil Mixing (CDSM) Projects. Field sampling and testing are also used for determining the performance and quality of soil mixing method(s) and are the primary basis for accepting or rejecting the soil mixing wall among all other QC testing. Two of the most commonly recognized and used sampling methods for CDSM walls are wet grab sampling and verification coring. Depending on the types of wall construction and project budget, one or both of these methods are normally used to help evaluate the in-situ matrix and quality of the mixed soils. Additional to ASTM strength and permeability testing from wet grab sampling and verification coring, more and more testing methods are being employed and accepted. However, these other testing methods tend to be unnecessary, lack consistency and repeatability, and are more subjective to manipulation and interpretation. In certain projects, there are also misconceptions involved with the results of wet grab sampling and verification coring, hence it is important to note how these wet grab sampling and verification coring work and represent the work in terms of quality of production.TYPES OF PROJECTSCDSM projects include (but not limited to) in-situ stabilization, liquefaction mitigation, excavation support, groundwater cutoff, and pollution containment. Although these projects use similar equipment on the jobsites, each project is treated differently in terms of catering to specification, uses of different mix designs, and emphasis on certain steps during production.Different types of projects with different specification changes the focus of quality, but soil types in jobsite also determine how to proceed with production. For example, a jobsite with predominate gravel layer must be treated differently as opposed to jobsite with clayey sand as the main soil type.WET GRAB SAMPLEWet grab sampling is one of the most used testing methods for QA/QC. The wet grab sample specimen is retrieved right after finishing the production of the desired element.Wet grab sampling equipment consist the use of 28 cubic inch (458.84 cubic cm) box attached directly to one of the auger stems. Hinges attached to the top and bottom of the box is fabricated to allow collection only during auger withdrawal. The collection box is strapped just above the mixing paddles on the auger stem and measured from the center auger head tip to confirm proper depth of collection. This box method has been used in Japan and U.S. for numerous projects."

Jan 1, 2017

By L. Narhi, K. Haavanlammi

"Approximately two thirds of annual nickel production is used as a raw material in the making of stainless steel, and about 60% of these nickel products are in the form of metallic nickel such as nickel cathode or briquettes. In the stainless-steel production process nickel is blended with iron and chrome-based raw materials, and metallic nickel is typically only required for final steel fine-tuning. Outotec offers a new FeCrNi technology to enhance the nickel value chain for stainless steel producers. This involves the use of an HPAL-based intermediate nickel product (e.g., mixed hydroxides or NiO) as raw material in the Outotec FeCrNi process, for the production of a FeCrNi Master Alloy. The new process, designated as the FeCrNi process, offers multiple benefits compared to existing technologies such as: higher tolerance for impurities in the HPAL intermediate product, avoiding the need for further nickel refining, and the improved recovery of all metals in the FeCr process. The complete new FeCrNi value chain is based on proven technologies such as HPAL and the Outotec FeCr-process. This new innovative and promising value chain offers improved efficiencies for the HPAL based nickel production process combined with excellent sustainability aspects.INTRODUCTION In today’s global economy there is a constant need to improve the efficiency and sustainability of the metals production. The requirements for modern metal refining are tightening and cost efficient, safe and sustainable operation is the precondition for all investment. Outotec is offering now a novel way to combine FeCr and Nickel production to create a completely new value chain to source nickel to stainless steel. BACKGROUND Nickel The current nickel mine production is in the level of 2,000 tons annually and it is split 44% from sulphide based deposits and 56% from laterite deposits (Figure 1). Most (40%) of the nickel is refined to pure nickel metal whereas other products are FeNi (19%) and Nickel Pig Iron NPI (20%) (Roskill). The remaining part, roughly 21%, is nickel chemicals and intermediates. Most of the new investments in nickel are in the direct shipping of laterite to produce nickel pig iron. HPAL process is considered in few projects but no major HPAL projects have been started since the Ambatovy plant in Madagascar. Ambatovy reached the commercial production in 2014. The main primary nickel used is stainless steel manufacturing. In the year 2016 about 68% (~1,360 kt) of primary nickel production was used in stainless steel."

Jan 1, 2017

By M-d-N. Gagnon, P. Okono, Y. Bergeron

In the mining industry, decisions regarding the type and number of comminution tests to be completed typically rely on geologists? observations and conclusions when studying drill cores. Given that these decisions are based on visual observations, they are essentially approximate and often inaccurate from a comminution viewpoint, causing a sizeable margin of error in estimating characterization test needs. Consequently, companies are often forced to perform more tests than necessary, requiring a significant quantity of material, and accruing significant costs. Recently, a new device, called the Hardness Index Tester (or HIT), was developed, offering users a low cost in-house mechanism for estimating the comminution parameter A*b and the Bond Ball Mill Work Index at any mine site, with potential applications on fragments up to 25 mm from drill core. In late 2016, Agnico Eagle Mines Limited initiated a trial to investigate if having an HIT device installed in a core repository would make it possible to identify the different rock properties more accurately and determine the number and type of comminution tests required. The application of the HIT was not to replace the standard comminution tests, but rather to generate a high number of comminution and geomechanical parameters for the rock mass. Ultimately, the objective would be to determine the uniformity of the rock mass and, therefore, easily distinguish any potentially problematic zones. With this method, the appropriate number of standard tests could be determined, making the HIT not only an excellent complement to the standard laboratory tests, but also an indispensable device for a geometallurgical characterization. This paper presents the results from the HIT trial using samples from the Odyssey Project, which is a Mine Canadian Malartic property.

Jan 1, 2017

By S. Castro, L. Gutiérrez, L. Uribe

"Use of lime in seawater as a pyrite depressant decreases Mo recovery in flotation of Cu- Mo sulfide ores. When technology that uses sodium metabisulfite (MBS) to depress pyrite is applied, the process is carried out at pH 6.5–7.5, the range where Mo recovery is higher than the usual pH 11.0–12.0 when lime is applied. Redox conditions and chemical reactions involved in depression mechanisms of pyrite by MBS, or sodium sulfite, in seawater are investigated and discussed based on the acidifying effect of MBS, oxidation of sulfite ions by dissolved oxygen, and the role of catalyst of some metal cations (e.g., copper ions) adsorbed on pyrite’s surface.RÉSUMÉ L’utilisation de chaux dans de l’eau de mer comme agent déprimant de la pyrite réduit la récupération de molybdène (Mo) dans la flottation de minerais sulfurés de Cu-Mo. Lorsque l’on applique la technologie utilisant du métabisulfite (MBS) de sodium comme agent déprimant de la pyrite, le procédé se fait à un pH de 6,5 à 7,5, gamme dans laquelle la récupération de Mo est supérieure au procédé habituel utilisant un pH de 11,0 à 12,0 lorsque l’on applique de la chaux. Les conditions de réduction-oxydation (redox) et les réactions chimiques impliquées dans les mécanismes de dépression de la pyrite par le MBS (ou sulfite de sodium) dans de l’eau de mer sont étudiées et débattues sur la base de l’effet acidifiant du MBS, de l’oxydation des ions sulfites par de l’oxygène dissous et du rôle de catalyseur de certains cations métalliques (par exemple les ions de cuivre) adsorbés à la surface de la pyrite. INTRODUCTIONThe copper industry is aware of the difficulties of floating Cu-Mo sulfide ores in seawater. Molybdenum recovery is partially depressed when lime is used to reject pyrite. In plant practice, sodium metabisulfite (MBS) has been demonstrated to be the most promising option for replacing lime in seawater."

Jan 1, 2017