Search Documents

By Junhyun Choi, Allan Gomez-Flores, Chonbuk National University, Siyoung Q. Choi, Gahee Kim, Seungkon Kim

In this study, to confirm the effect of depletion attraction on the flotation, we theoretically and experimentally investigate the effect of the depletion attraction force on flotation. While varying the concentration of the depletion agent (polyethylene glycol), three different systems are studied: pure malachite, pure silica, and a 1:1 mass ratio of malachite and silica binary system. We find that recovery increases significantly as the concentration of the depletion agents increases for all three systems, as the depletion agent facilitates the adsorption of the particle on the bubble surface. However, the recovery suddenly decreases in a certain concentration range, which corresponds to the onset of the decreased surface tension when high concentrations of the depletion agent are used. This non-monotonic overall recovery trend implies the surface adsorption of the depletant on a surface. The decreased surface tension of the air/water interface suggests that the recovery rate is lowered due to the adsorption of the depletion agent to the bubble surface, acting as a polymer brush. Based on our observations, we conclude that the depletion force can greatly improve particle adsorption, as predicted in the accompanying theory paper, while simultaneously the adsorption of the depletion agent on the bubble surface plays an important role because it hinders particle adsorption. We also perform experiments in the presence of a small amount of a collector, sodium oleate. An extremely small amount of the collector leads to the increase in the overall recovery, which eventually reaches nearly 100 percent. Nevertheless, the grade worsens as the depletant provides the force to silica particles as well as target malachite particles.

Jan 1, 2016

By Michael Murphy, Khaled M. Mohamed, Berk Tulu

"Failures of coal ribs are major hazards in underground coal mines. For the period of 2010 to 2014, rib falls were the leading cause of groundfall fatalities and accounted for 35% of all groundfall-related fatalities. Currently, the National Institute for Occupational Safety and Health (NIOSH) is conducting a research project to develop an engineering-based design methodology for rib control in underground coal mines to reduce rib fall accidents and fatalities. Numerical models can be used as part of the design methodology provided the models are appropriately calibrated and verified.This paper presents a coal rib model to simulate the mechanism of coal deformation and fracturing that can lead to stress-driven rib falls. The proposed coal rib model was calibrated against published data from an instrumented rib site at the West Cliff Mine in Australia. Fracturing of the coal rib was defined by critical VALUES (of plastic shear strain of the coal material and rib displacement. A critical plastic shear strain of 2.8% and a sudden increase of rib displacement of 30 to 45 mm were sufficient to develop a fracture plane in the rib model. Accordingly, a discontinuous rib deformation was achieved and it compared favorably against field monitoring data.INTRODUCTIONCoal ribs are the vertical walls of coal formed when entries are developed in a coal bed. Failures of coal ribs are a major hazard in underground coal mines. Furthermore, failing ribs can contribute indirectly to roof and floor instability by increasing opening widths across intersections and entryways. Over the last 18 years, there has been a continual occurrence of injuries and fatalities in underground coal mines due to rib falls. For the period of 2010 to 2014, rib falls (excluding longwall face failure and bursts) were the leading cause of ground fall fatalities and accounted for 35% of all groundfall-related fatalities (MSHA, 2015)."

Jan 1, 2016

By L. Yuan, A. Smith

"NIOSH’s mine fire simulation program, MFIRE, is widely accepted as a standard for assessing and predicting the impact of a fire on the mine ventilation system and the spread of fire contaminants in coal and metal/nonmetal mines, which has been used by U.S. and international companies to simulate fires for planning and response purposes. MFIRE is a dynamic, transient-state, mine ventilation network simulation program that performs normal planning calculations. It can also be used to analyze ventilation networks under thermal and mechanical influence such as changes in ventilation parameters, external influences such as changes in temperature, and internal influences such as a fire. The program output can be used to analyze the effects of these influences on the ventilation system. Since its original development by Michigan Technological University for the Bureau of Mines in the 1970s, several updates have been released over the years. In 2012, NIOSH completed a major redesign and restructuring of the program with the release of MFIRE 3.0. MFIRE’s outdated FORTRAN programming language was replaced with an object-oriented C++ language and packaged into a dynamic link library (DLL). However, the MFIRE 3.0 release made no attempt to change or improve the fire modeling algorithms inherited from its previous version, MFIRE 2.20. This paper reports on improvements that have been made to the fire modeling capabilities of MFIRE 3.0 since its release. These improvements include the addition of fire source models of the t-squared fire and heat release rate curve data file, the addition of a moving fire source for conveyor belt fire simulations, improvement of the fire location algorithm, and the identification and prediction of smoke rollback phenomena. All the improvements discussed in this paper will be termed as MFIRE 3.1 and released by NIOSH in the near future INTRODUCTION The MFIRE program, originally developed in the 1970s by the U.S. Bureau of Mines (now the Office of Mine Safety and Health Research (OMSHR) at the National Institute for Occupational Safety and Health (NIOSH)) and Michigan Technological University, has been a mainstay in modeling of the mutual influences between a fire and the mine ventilation system during an underground mine fire. Several update versions have been released over the years, including MFIRE 1.27, 1.29, 1.30, 2.0/2.01, 2.10, and 2.20. The MFIRE program logically comprises four parts: (1) a conventional network calculation, where it performs the basic network balancing without considering heat or mass transfer; (2) a temperature calculation to establish the reference temperature distribution before a non-steady state (transient-state) simulation; (3) a transient-state simulation that follows changes in ventilation step-by-step to produce a continuous description of the temperature distribution, smoke, and contaminant spread through the ventilation system during a fire event; and (4) a quasi-equilibrium simulation to predict the state of the ventilation system after a relatively long period of time (defaulted as 5 hours in MFIRE) as the fire reaches a quasi-steady state. In summary, MFIRE is a computer simulation program that performs normal ventilation network planning calculations and dynamic transient-state simulation of ventilation networks under a variety of conditions including the influence of natural ventilation, fans, fires, or any combination of these (Chang et al., 1990)."

Jan 1, 2016

By V. van der Merwe, C. W. Siyasiya

"A petrochemical company experiences premature thermal fatigue failure of the casting moulds used in catalyst production. The aim of the project was to find an alternative alloy that would outperform the current low-alloy cast steel used for the moulds. Based on their thermo-fatigue properties, 3CR12 ferritic stainless steel and H11 tool steel were chosen for testing and comparison with the currently used BS3100 B7 cast steel. Samples of each material were subjected to temperature cycling in a Gleeble 1500TM thermo-mechanical processing simulator, followed by surface analyses. The main parameters derived from the test work were the total true strain, the hot strength of the materials, and the number of cycles to failure. Additionally, the coefficient of thermal expansion for each material was measured using a Bähr dilatometer. H11 tool steel yielded the best performance by way of having the fewest surface cracks, the lowest total true strain per cycle, the most cycles to failure, the highest hot strength, and the lowest coefficient of thermal expansion.IntroductionThe Catalyst Manufacturing Plant (CMP) is a dusty environment with temperatures higher than ambient. Molten mill scale (magnetite, Fe3O4) is tapped from the electric arc furnace into the casting moulds at temperatures close to 1600°C. After 10 seconds the magnetite is quenched with a water spray for 50 seconds to a minimum temperature of 400°C. Sometimes there is residual water in the pans from the cooling fog process (water sprays) in the empty mould. In a typical plant, the factory produces 40–44 batches a day containing between 150–300 moulds, depending on the time required for the specific batch (Buchholz, 2014). The typical batch in the CMP usually weighs about 6 t. The thickness of the tap, speed of the casting belt, and tilting angle all affect the number of moulds per batch.One of the main problems faced during the molten mill scale casting is the premature failure of the casting moulds. Cracks initiate on the surface of the mould, which is in contact with the hot catalyst, and propagate into the interior of the mould. Cracks are generally concentrated in the middle area of the mould where the catalyst makes first contact with the mould, and which experiences the highest temperature fluctuations. This suggests that the cracks are caused by thermal fatigue during the casting process."

Jan 1, 2016

"A carefully planned laboratory test program is the foundation for the successful development of a sulfide flotation process. In this paper, the development of a copper-molybdenum flotation process is described. However, the concepts discussed can be applied to most sulfide flotation systems and to many industrial minerals projects as well. Each step is examined, beginning with sample procurement and covering sample preparation, flotation test preparation grinding, scoping flotation tests for reagent scheme selection, rougher flotation parameter evaluation and cleaner circuit evaluation, through to locked-cycle testing and pilot plant design and operation. Ore variability and modeling to determine the response of various ore types to the optimum conditions established is also examined.IntroductionA carefully planned laboratory test program is essential for the successful development of any sulfide flotation process. These programs usually begin with a series of batch tests on several ore type composites to evaluate appropriate reagent schemes and delineate optimum rougher flotation conditions, such as primary grind size, flotation pulp density, flotation pulp pH and retention time. Cleaner parameters such as regrind size requirements, cleaner pH, pulp density and number of stages are then defined. Semicontinuous locked-cycle tests are performed using the parameters established in the batch tests to determine the effect of middling streams recirculation on flotation performance. The data generated and the experience gained in the locked-cycle tests may be used to design and operate a continuous pilot plant if relatively large amounts of concentrate are required for further process development, such as optimization of byproduct molybdenum production from bulk copper-molybdenum concentrate.A comprehensive ore variability program is undertaken to determine the response of various ore types to the optimum conditions established. These ore variability programs often test hundreds of samples in standardized batch rougher and cleaner tests to ensure that the orebody is well understood.This article describes the development of a copper-molybdenum flotation process, but the concepts discussed can be applied to most sulfide flotation systems and many industrial minerals projects. The block flow diagram in Fig. 1 provides an overview of the development process."

Jan 1, 2016

By Anita Wu

"GENERAL BACKGROUND/CONTEXT The £300 million Bond Street Station Upgrade project will provide essential congestion relief and step-free access to an important interchange and destination station in the heart of the London Underground network. In 2010 London Underground (LU) let a design & build contract to Costain Laing O’Rourke (CoLOR), with the works to be completed in early 2017. CoLOR’s lead designer is Halcrow-Atkins JV (HAT). The station upgrade works comprise the following principal elements: •,A new satellite ticket hall on the North side of Oxford Street •,Two additional escalators and stairs providing congestion relief to the Jubilee line platforms •,Four lift shafts to provide step-free access between the different levels of the station •,Additional stairs to Central line platform level •,Tunnelled connection to the Crossrail station immediately to the south •,Connecting passageways, including ten connections to existing station tunnels. To achieve this, an existing property at 354-358 Oxford Street has been purchased and demolished, and the basement deepened to make provision for the new ticket hall. From this basement two circular shafts have been sunk, providing construction access for the tunnelled passages and lift and escalator shafts. The tunneling is principally in the London Clay stratum, which is widely recognized as a favorable tunneling medium, although the deepest parts of the works extend into the Lambeth Group strata which consist principally of stiff clays at this level but also contain water-bearing sands. The majority of tunneling has been carried out using mechanical excavation and sprayed concrete linings but other techniques have been used in areas where SCL is not practicable.A key challenge for design and construction of the works has been spatial constraint, in particular due to: •,The existing underground station layout •,The Limits of Deviation for the works •,The small construction site at 354-358 Oxford Street •,Overlaying Third Party assets including Listed buildings, sewers and water mains."

Jan 1, 2016

By H. Jung, J. Kim, Y. Lee, Y. Seo

"Shale gas has become an increasingly important source of natural gas supply in North America and around the world. Horizontal drilling and multi-stage hydraulic fracturing are the two key enabling technologies for the economic development of these shale gas reservoirs. It is believed that gas in shale reservoirs is mainly composed of free gas within fractures and pores and adsorbed gas in organic matter (kerogen). It is generally assumed in the literature that the monolayer Langmuir isotherm describes gas adsorption behavior in shale gas reservoirs. In this work, we have analyzed several experimental measurements of methane adsorption from the Horn River Shale core samples that obey the Langmuir isotherm. INTRODUCTION In nature, gas shales are characterized by extremely small grain size, extremely low permeability on the order of nano-Darcy (10-6 md), small porosity, and high total organic carbon (TOC). Shale can serve as both source and reservoir rock. The amount of gas in place in shale is strongly affected by the TOC, clays, and the adsorption ability of methane on the internal surface of solid (Martin et al., 2010). Since a considerable amount of gas in shale reservoirs is adsorbed, investigation of gas adsorption can provide critical insights into evaluation of well performance and reservoir characterization. Generally, natural gas in shale reservoirs is stored as free gas in both larger mineral pores and natural fractures, as well as adsorbed gas within organic matter (Leahy-Dios et al., 2011). EXPERIMENT METHOD & THEORY Adsorption Experiment Several experiments were carried out on 9 shale core samples obtained in a vertical well drilled within Horn River basin (Figure 1). The CH4 adsorption isotherms were measured for the different depth. In order to measure the amount of adsorbed gas, the high pressure Belsorp-HP equipment applying volumetric method was used. The temperature was kept at 298 K and pressure was increased up to 18 MPa. Approximately 5 g of crushed sample was used for each measurement."

Jan 1, 2016

By E. Ghali, C. Su, G. Houlachi

"The influence of lead ions on zinc electrowinning process was investigated by means of electrochemical noise measurements (ENMs) and cyclic voltammetry in conjunction with scanning electron microscopy and X-ray diffraction. All electrochemical experiments were performed in sulphuric acid electrolyte containing different lead ion concentrations as impurity. Lead was added in six trace levels between 0.05–0.8 mg/L in the bath. The lead content of the zinc deposits was dependent on the introduced lead concentrations. The overpotential associated with zinc electrodeposition shifted to higher values with the increase of lead concentration in the solution. An appropriate correlation was found between the different concentrations of lead in the electrolyte and the morphology of zinc deposit by ENM. The results showed that the increase of lead ion concentrations is generally accompanied with the decrease of skew and increase of kurtosis values that could be related to the morphology of zinc deposit. Effectively, the morphology changes from well-defined hexagonal platelets to large hexagonal, layered platelets and finally to non-symmetric refined crystalline structure, respectively.INTRODUCTION In commercial zinc electrowinning, zinc oxide is leached from the roasted calcine with an aqueous acid sulfate electrolyte. Then the zinc-rich solution is purified and transferred into an electrolytic cell. During electrolysis, zinc is deposited on aluminum cathode where lead-silver or pure lead is served as anode. Electrodeposition of zinc could be influenced by several parameters such as bath acidity, temperature, current density, the nature and concentration of impurities as well as additives in electrolyte. Metallic impurities play a complex role during zinc electrowinning and they can adversely"

Jan 1, 2016

By Eckl, Martin, Stefan Lemke, Martin Londschien

"Tunnels are built with a design life expectancy of over 100 years. One key component of such a design is the waterproofing system, which must reliably fulfil its function during the whole service lifetime of the tunnel structure. This paper deals with the determination of test criteria for the durability assessment of geosynthetic products in tunnel sealing systems. Hereby the understanding of the individual aging processes is crucial along with the long-term experience with these materials to ensure the transfer of the laboratory results and performance to site practice (test calibration) and vice versa. To verify the results of the new test procedure the material properties of geosynthetic products samples removed from older tunnels are investigated. Based on the presented results of the still ongoing research programs some preliminary conclusion regarding the updating of regulations for tunnel sealing systems are given. INTRODUCTION Watertightness is directly related to the durability and serviceability of the concrete lining. Therefore, modern traffic tunnels and shafts (Figure 1) are generally protected against mountain/ground water and water penetrating through rock fissures by a sealing system, for example with a loose-laid polymeric sheet membrane. Hereby the waterproofing sealing systems must be reliably fulfilling their function during the whole service life of the tunnel structure, regularly of more than 100 years. In consequence, the quality and lifetime performance of the waterproofing materials—beside the correct professional and careful installation in a tunnel infrastructure, is of great importance. The challenge for the industry, owners, operators and designers is ultimately the development of qualification testing and requirements (acceptance criteria) for products to ensure the design lifetime performance. Hereby the qualification procedure is seen as a routine integrated in standards, norms or guidelines, wherein test procedures should cover typical environments for the specific application fields. Polymeric synthetic raw materials are increasingly used in products with long service lifetimes (e.g. in injections, gaskets, waterbars, spray-applied and sheet waterproofing membranes). During service they are subjected to chemical (e.g. oxidation processes) and physical (e.g. changes in morphology) influences from the environment, which affect their mechanical properties—and they age. Hereby organic materials are more affected than inorganic materials. Also, polymers show strongly temperature-dependent properties compared with other construction materials. However, their long-term aging behavior is not given per se and has to be explored extensively by suitable tests, which simulate—under accelerated processes—real exposures and loads. Hereby the understanding of the individual aging processes is crucial along with the long-term experience with these materials to ensure the transfer of the laboratory results and performance to site practice (test calibration) and vice versa."

Jan 1, 2016

By Joe Silvestri, James Carroll, Steve Rondinelli, Raelene Shelly, Jason Miller

"The I-70 Eisenhower-Johnson Memorial Tunnel (EJMT) Fixed Fire Suppression System (FFSS) will help protect the traveling public as well as the entire tunnel itself, which is a critical asset of the Colorado highway system. This project is part of an effort to avoid any closure or long-term damage to these tunnels after a fire event. Historically, the EJMT complex has experienced two to three fires a year. While CDOT has firefighting capability at the EJMT complex, the fixed fire suppression system will provide first responders the critical time needed to safely approach the scene and take action, and is a necessary tool in combating tunnel fires, keeping the public safe, protecting the tunnel structure, and minimizing disruptions to traffic. This paper provides a case history of the first-of-a-kind design and construction of the EJMT FFSS. Major project elements include; water-only deluge fire suppression system, fiber optic linear heat detection system, updated fire alarm system and new drainage system. PROJECT BACKGROUND The I-70 EJMT FFSS was awarded to the Design Build Team lead by Barnard Construction, supported by Rondinelli Life Safety, BCER Engineering, ILF Consulting, Western States Fire Protection and Systems Group. The team conducted successful live fire tests at the Boulder Regional Fire Training Facility in November 2014, with the final design of the FFSS and other supporting infrastructure completed in the spring of 2015. Construction began in early summer of 2015 and the project was completed in December 2015. While CDOT currently has firefighting capability at the EJMT complex, this project features an intelligent linear heat detection system that can accurately identify a fire within feet of its location and subsequently activate the corresponding water-only FFSS deluge zone, bringing water in from an existing supply system on the west side of Loveland Pass. The detection system also activates cameras so the EJMT onsite control room personnel can view and better assess a fire event. The uniqueness of this design is that the majority of the installation occurred above the traffic lanes in the tunnel, which resulted in minimal impacts to motorists below. The fire suppression system will help protect the traveling public as well as the tunnel structure, a critical asset to the highway system. This project is intended to reduce damage and avoid long-term closures of the tunnel due to fires. A long-term closure could cost Colorado billions of dollars and negatively impact tourism along the I-70 mountain corridor."

Jan 1, 2016

By K. Wu, X. Yuan, R. Du, C. Chao

"Lump coals are currently employed to replace part of coke in the COREX melter-gasifier for ironmaking. In order to optimize the process, the pyrolysis kinetics of Datong coal used in the COREX process was studied. A sectioning method is proposed to overcome certain shortcomings of traditional methods for studying the pyrolysis of coal. Based on the sectioning method and the characteristics of the coal pyrolysis process, the temperature range was divided into three intervals. In the first, the adsorbed gas and water of crystallization were removed; in the second, the coal was transformed into semi-coke; and finally, the semi-coke was further coked. Three models of reaction were then established to study the different stages of the pyrolysis process: an interfacial chemical reaction model, a random pore model, and internal diffusion with shrinking volume. The results showed that the experimental data fitted the models well, with all correlation coefficients (r2) exceeding 0.97. Finally, the mechanisms of reaction and kinetic parameters for each temperature range were derived, which laid a necessary foundation for optimizing the usage of non-coking coal in the COREX process. IntroductionIn view of environmental concerns and the shortage of good-quality coking coal, the COREX process was designed as a new ironmaking technology, attracting wide attention (Fang et al., 2005). In this process, lump coal and a small quantity of coke are directly charged into the melter-gasifier, where a high-quality reducing gas is generated for the reduction of the iron ore (Kumar et al., 2009). In contrast to the conventional blast furnace (BF) process, non-coking lump coal is used as the reducing agent and as the energy source, and the iron charge consists of lump ore and/or pellets, which results in the elimination of the coke oven and sintering plant as well as a decrease in investment (Kumar et al., 2009; Liu et al., 2012).Although the COREX process has made great progress, in current production practice the energy consumption greatly exceeds that of the BF, and it requires a certain amount of coke to maintain permeability of the semi-coke bed (Wang et al., 2008). In addition, the process consumes a lot of good-quality lump ore and lump coal. The pyrolysis of coal is the first step in most coal conversion processes, such as carbonization, gasification, and combustion (Aboyade et al., 2013). The reaction behaviour of lump coals in the COREX melter-gasifier is crucial, as it determines energy utilization and gas composition, as well as the metallurgical properties and particle size of the semi-coke produced (Prachethan et al., 2011; Zhang et al., 2014). In order to optimize the process and improve its competitiveness, the pyrolysis kinetics of Datong coal used in Baosteel’s COREX C-3000 facility was studied."

Jan 1, 2016

By S. Tuylu, D. Adiguzel, A. Bascetin, O. Ozdemir, U. Cinar

"In recent years, use of mineral processing tailings as a paste backfill has been significantly increased due to the environmental problems occurred during the disposal of the tailings in mine area. The paste material used to fill the stopes excavated is generally consisted of tailings (solid ratio: 70–85%) and cement (3-7%w/w). Meanwhile, the strength of the paste material is completely related to ratios of these materials. Cemented Paste Backfill (CPB) system is used as support depending on the roof pressure and also as an underground disposal method. Therefore, temporary strength value of the paste material gains a great importance. For example, the paste backfill material must compensate the minimum 4 MPa strength value in order to procure the permanent fortification, and the mixture cost must be minimal as well. For this reason, in this study, the Pb-Zn tailings were used to prepare for the paste backfill material using cement in order to perform the uniaxial compressive strength (UCS) tests. Additionally, a statistical experimental design and linear programming techniques was used to find the optimum mixture in terms of strength and cost. The pulp solid ratios (PSR) of the tailings and cement (by the solid) were varied as 75-85% and 3-8%, respectively. The results of this study; the optimum mixture is ~79.5%PSR and 6.8% cement ratio (by the solid) for 4 MPa UCS (28 day) and 16-17 cm slump value determined by this method with statistically reviewed experimental data. INTRODUCTION Fine-grained tailing waste materials resulting from mining activities are an important environmental problem. In terms of environmental protection, the use of tailings with paste backfill is a very attractive approach and a desirable solution to tailings management. Paste backfill, which is used to fill underground openings, is made by primarly mine tailings mixed with hydraulic binders and water. Its main benefits are not only disposal of mine tailings in underground, but also providing a certain strength to ensure a safe working environment. Therefore, it is necessary to use hydraulic binders due to durability of the system (Benzaazoua et al., 2004). Paste backfill, formed from the mix of dewatered plant tailings (75-85 wt. % solids), water and binder (3-8 wt. %) (Brackebusch, 1994; Landriault et al., 2005).Water is used to determine the chemical reactions between tailing and binder materials for strength as well as increasing pumpability. Portland cement and ash can be used as binder materials (Douglas and Malhotra, 1987). The factors which affect strength and stability of paste backfill separate into two groups called interior and exterior factors. Interior and exterior factors determine the strength, stability and deformation features of backfill in short and long terms and also affect the transportation of backfill to underground (Benzaazoua et al., 2004; Erçikdi et al., 2006; Yilmaz et al., 2010; Nasir and Fall, 2010). Material properties of tailings as well as site operations to fill the underground openings are the most important steps for the design purposes. Grain size distribution, chemical, and physical properties of tailings, and mechanical properties of paste fill material are used to understand the suitability of tailings as paste fill material (Ozturk et al., 2014). In addition, Fig. 1. is also proposed to apply a typical design for the operational stages of paste fill applications on the site."

Jan 1, 2016

By Tong Guan, Guangqin Fu, Lihong Deng, Yuanlin Chen, Xiaotong Zhou

"In natural world, some kinds of scheelite minerals are rich in molybdenum. Molybdenum exists in the crystal lattice of scheelite in the form of isomorphism, and the content of MoO3 varies from 2% to 10%. As a result, the flotability of seyrigite (scheelite with molybdenum) turns to be weaker. One seyrigite mine, which has been built for 3 years,still could not produce qualified seyrigite concentrate due to the weak flotability of seyrigite (Mo-bearing scheelite) in raw ore. In our experimental research, through adopting new seyrigite collector TA-3 and advanced mineral processing technology, the seyrigite concentrate with a grade of 65.62% WO3 at a recovery of 87.47% was obtained for the raw ore containing 0.19% WO3 and 0.074% Mo. By applying the new technical achievement, for the raw ore containing 0.272% WO3, the seyrigite concentrate assaying 68.03% WO3 with a recovery of 77.56% was obtained in industrial production.INTRODUCTIONIn natural world, some kinds of scheelite minerals are rich in molybdenum. Molybdenum exists in the crystal lattice of scheelite in the form of isomorphism, and the scheelite is changed to be seyrigite (Ca[(W,Mo)O4]) (Ma, Bian, & Wang, 2013). The content of MoO3 in seyrigite varies from 2% to 10% usually, the content of MoO3 in some of the seyrigite even reaches 34%. The flotability of seyrigite is weak (Zhang, 2007), and the seyrigite is difficult to be recovered by flotation with common collectors and regulators. One scheelite mine in Anhui China, which is a skarn type seyrigite mine, has not produced qualified concentrate yet since 3 years it has been built due to the limit of beneficiation technology. Therefore, it is necessary to conduct research on the collectors with high efficiency and developing advanced processing flow for this kind of ore."

Jan 1, 2016

By Peter Johnson, David Barber, Lachlan Henderson

"The traditional approach to rail tunnel fire safety design is to follow NFPA 130, which assumes a major tunnel fire could occur and requires bi-directional emergency ventilation. There is no regard to the impact of ventilation on fire growth and smoke production. In Europe and other parts of the world, the need for tunnel ventilation systems to provide smoke management in the event of fire is being questioned. The European Commission’s Safety in Railway Tunnels TSI is based on a philosophy that improved running capability (preventing fires and other events stopping the train in the tunnel) and elevated fire performance of materials means the chances of a major fire in a tunnel is highly unlikely, with only small fires expected, and no tunnel ventilation required. This approach is reinforced by the International Tunneling Association which has recently published an Engineering Methodology for Performance Based Fire Safety Design on Underground Rail Systems, which includes a methodology that does not require assessment of tenability in tunnels, but requires a scenario based risk assessment to be undertaken to determine overall fire safety measures. Recent research by the University of Edinburgh has shown that forced airflow from a mechanical ventilation system may promote fire growth and increase smoke volumes much more than with natural ventilation. Whilst the concept of no mechanical ventilation (i.e. natural ventilation) is a new concept for some, for many rail tunnels it is worthy of serious further consideration. RAIL TUNNEL SMOKE MANAGEMENT AND STANDARDS Smoke management using mechanical bi-directional ventilation systems has been a central part of the fire safety design solution under NFPA 130 for rail tunnels since 1982. The current version of the standard, NFPA 130: 2014, states that mechanical ventilation should be fitted to rail tunnels of length greater than 305 meters and an engineering analysis should be undertaken for tunnels of length 61 to 305 meters to determine whether mechanical ventilation should be fitted. However, this approach is not necessarily reflected elsewhere in the world. In Europe in particular, mechanical ventilation systems for smoke control within rail tunnels have taken a much less central role within the standards framework."

Jan 1, 2016

By N. P. Hristov, L. V. Kuzev

"A simulation study of the fill factor of a drum mill was conducted using two types of grinding media: balls and tetraballpebs. Each medium was composed of equal number of grinding bodies having equal weight but different shape. The difference was in the density of the two grinding media.Standard spherical grinding bodies (balls), which were used in practice, and equivalent (by weight) grinding bodies in the shape of spheroidal tetrahedrons (tetraballpebs) were studied. The simulation was conducted in a module of a 1.2 m diameter drum mill, whose length exceeded twice the diameter of the corresponding grinding body. The grinding balls had a few percent (3 to 6) higher fill factor than the grinding tetraballpebs in the same shell.Vertical sections of the grinding medium were taken across the studied shell module along its axis. They showed the location of each grinding body in the fill volume. Defects in the packing of the grinding bodies and the contacts between them and with the inner surface of the shell were also show. Differences in the contact points of the balls and the tetraballpebs were noted. For the tetraballpebs, we observed contacts both between the spherical surfaces and with the edges and vertices of the grinding bodies.The topography of the grinding media is shown visually.INTRODUCTIONThe grinding balls have been studied extensively. It is the traditional grinding medium in ore processing industry. The parameter characterising the grinding medium is its density. It is the mass of the grinding medium per unit of volume. The parameter may have a range of values. It depends on:• The physical properties of the material they are made of;• The shape of the grinding body;• The dimensions of the body;• Size distribution of the grinding bodies in the grinding media.In comminution, the fill factor of the mill shell is the process parameter that is representative of the grinding medium. Some publications have indicated the disadvantages of ball grinding. For example, Wu, Xiang, Glen, and Duan (2008) note in the analysis of the mechanism of grinding that the balls are not the best grinding media and disadvantages include among others:• Easy over-grinding resulting from the point contact between the balls;• Attrition surface is the smallest in the grinding media;• Poor selective exposure of minerals resulting from the accidental and often significantly more powerful impact on the feed;• The grinding efficiency drops as the fineness of grind is increased;In the Handbook of mineral processing, Polkin (1950) noted that the shape of the grinding bodies determines the volume of the void spaces therein and therefore the shape affects the grinding efficiency per unit of volume of the grinding medium."

Jan 1, 2016

By K. Loutet, A. Guenkel, K. Nikolaisen

"The INCO SO2/air process was patented by INCO in 1985. Well over 80 mining operations worldwide are using this process to oxidize cyanides to cyanates in the tailings from gold, silver and copper mining operations. The sulphur dioxide (SO2) for this process can be supplied either as liquid SO2, SO2 gas or as a sulphite-based salt. The majority of SO2/air operations have used sulphite-based salts as the ‘SO2’ equivalent probably due to low capital cost. Liquid SO2 has also been used frequently, but due to concerns with safety and availability, this option is often not preferred. The solid salt sodium meta-bisulphite (SMBS) is commonly employed, but its cost is an order of magnitude higher than that of sulphur. Due to the high cost of SMBS, the increased capital cost for a sulphur-burning SO2 gas plant (green field or retrofit) usually has a pay-back of less than three years. In addition, a SO2 gas plant offers potential for significant heat recovery from the sulphur burning process. In terms of safety, the SO2 gas plant only requires the storage of relatively benign sulphur and the site inventory of SO2 will be limited to the plant gas volume. Therefore, a SO2 gas plant will not trigger the Canadian Environmental Protection Act (CEPA) E2 Regulations or the US Clean Air Act Section 112(r) accident prevention regulations, as may be the case for liquid SO2.Most existing mining operations using ‘SO2’ are gold operations, but in recent years there has been an increased interest in larger sulphur dioxide gas plants for hydrometallurgical facilities that employ leaching of cobalt/manganese minerals or precipitation of manganese/iron (e.g. Tenke Fungurume and El Boleo).This paper focuses on the production of sulphur dioxide gas generated on site and on demand for the use in hydrometallurgical processes. The capital and operational costs of a SO2 gas plant is compared to conventional process alternatives using sulphite-based salts or liquid SO2."

Jan 1, 2016

"Guideline Augered Cast-In-Place (ACIP) Pile Specification and Commentary11.0 GENERAL1.1 SCOPEThe Pile Contractor shall furnish all labor, materials, tools and equipment necessary for furnishing, installing and testing Augered Cast-in-Place (ACIP) piles as shown on the Contract Drawings and as specified herein.ACIP piles are commonly referred to by several other names. Some of them are trademarks or service marks owned by Foundation Contractors and some are names that try to describe the installation process. The term “cast-inplace” is sometimes replaced with “cast-in-situ,” especially in Europe. Some common names are Auger Cast Piles, Intruded Mortar Piles, Augerpress Piles, Augered Pressure Grouted Piles, AugerPile Foundations, Continuous Flight Auger (CFA) Piles, Grouted Bored Piles, Augered Grout-Injected Piles, Drilled or Augered Uncased Piles, and Uncased Cast-in-Place Concrete Piles. To avoid confusion, ACIP pile will be used exclusively herein.1.2 PILE CONTRACTOR QUALIFICATIONSThe ACIP piles shall be installed by an experienced Pile Contractor who upon request of the Engineer shall submit evidence of successful ACIP pile installation under similar job and subsurface conditions, including a job supervisor who shall have a minimum of five years of method specific experience.The proper installation of the ACIP piles is dependent upon the procedures used by the Pile Contractor’s field representatives and equipment provided. The Pile Contractor’s personnel responsible for the installation should have relevant experience with the auguring and pumping equipment, experience placing piles under similar site conditions (including restricted headroom if appropriate), in similar subsurface conditions, as well as experience handling the special grout mixes, admixtures, etc."

Jan 1, 2016

By Z. L. Xue, J. L. Li, X. Y. Wang

"In low-carbon energy-efficient basic oxygen furnace (BOF) steelmaking processes, limestone partly or completely replaces the active lime. The effects of limestone calcination temperature (1200–1500°C) and time (5–15 minutes) on lime reactivity and CaO grain size were investigated. The reactivity was evaluated by titration with hydrochloric acid, and the CaO grain size was analysed using scanning electron microscopy. The results revealed that for calcination temperatures higher than 1300°C, the reactivity reached a maximum and then decreased . The higher the temperature, the earlier the peak of reactivity appears. The CaO grains grow with increasing temperature and time, which leads to the decrease of reactivity. Notably, the effects of temperature on CaO grain size and reactivity are more marked than that of time. To obtain active lime calcined at ultra-high temperature by flash heating, the calcination conditions should be 1300–1400°C for 10–15 minutes, or 1400–1500°C for 8–10 minutes. IntroductionLime is one of the most important slag-making materials for dephosphorization and desulphurization in the basic oxygen furnace (BOF) steelmaking process. The reactivity of lime is a measure of its capability to take part in slag-making. Lime having a reactivity of more than 300.0 mL (4 N HCl), determined by hydrochloric acid titration is generally referred to as active lime (Rusjan et al., 2007; Zeman, 2008). At present, the active lime used for BOF processes comes primarily from a kiln or shaft kiln, where limestone is preheated at 700– 900°C, and then calcined at 1050–1200°C (Drenhaus et al., 2010; Oates, 2007)."

Jan 1, 2016

By R. Venugopal, V. K. Saxena, A. K. Mukherjee

"Coal, iron and manganese ore samples were exposed to different ultrasonic intensities of 250, 300 and 350 W/L for five minutes and to an ultrosonic intensity of 270 W/L for different time durations of 3, 5 and 7 minutes. The ultrasonically treated samples showed reductions in D80 particle diameters of 6 percent for the coal samples, 5.95 percent for the iron ore samples and 35.63 percent for the manganese ore samples during grinding. The ultrasonic treatment was also observed to assist in reducing ash content in the coal product by 8 percent and to reduce manganese losses in rejects by about 5 percent. Ultrasonic treatment was concluded to be capable of assisting in the comminution of friable ores more prominently than the hard and porous materials.IntroductionComminution is an important unit operation in the mineral-processing, cement-making, powergeneration and pharmaceutical industries. But most of the milling technologies are considered to be energy inefficient, with less energy consumed in real size reduction and most of the energy consumed in the machine. This is more critical for the mineralprocessing industry because of the growing need to exploit lower-grade ore bodies and process rejects (Blazy et al., 1994; U.S. Department of Energy, 2005). Low-grade ores require crushing and grinding to liberate the valuable minerals, which are further separated from gangues by various beneficiation methods such as gravity separation, flotation and leaching. Various studies have been carried out to minimize energy consumption during milling by developing pretreatment methods that can initiate new fractures or improve the fracture density in materials before comminution. These studies were mainly focused on chemical additives; thermal, ultrasonic and microwave treatments; and electric disintegration (Klimpel and Austin, 1982; Norgate and Weller, 1994; Bearman, Briggs and Kojovic, 1997; Gaete-Garreton, Vargas-Hermandez and Velasquez-Lambert, 2000; Kumar et al., 2010; Wang, Shi and Manlapig., 2011, Singh et al., 2012).The fragmentation effect of ultrasonic fields in solids has been investigated since the 1950s, and Gärtner was probably the first researcher who attempted it (Gaete-Garreton, Vargas- Hermandez and Velasquez-Lambert, 2000). Sound waves can propagate in solids in the form of longitudinal waves, shear waves and surface waves, and in thin materials as plate waves.In surfaces, fractures and interfaces, various types of elliptical or complex vibrations of the particles make other waves possible. During ultrasonic-vibration treatment, cavitation bubbles nucleate, grow and collapse, generating microjets, whose impacts on the particles initiate microcracks. The ultrasonic waves can enhance the nucleation, growth and coalescence of flaws, caused by tensile or shear stress. The mechanisms operating in the materials and inducing these stresses have been identified as spall and compression-induced tensile microcracks, nucleating at preexisting flaws. These mechanisms are driven by the shock wave and cavitation effects in the surrounding fluid (Chen, Huang and Shih, 2003)"

Jan 1, 2016

By K. Mayhew, A. Lossin, H. Salomon-de-Friedberg

"The proportion of arsenic-bearing copper concentrates that supply the copper industry is on the increase. The current strategy of miners and smelters to blend feeds to reduce average arsenic levels is rapidly becoming unsustainable as more concentrates with even higher arsenic levels enter the marketplace. In addition, the capability of smelters to manage increasing arsenic levels to more stringent and restrictive environmental standards is limited by available process technologies.CESL Cu-As Technology is a viable technical and economic alternative to traditional smelting. It offers the advantage of simultaneous leaching and precipitation of the arsenic in a single processing step while achieving high copper extractions. The process has been piloted in six separate, fully-integrated pilot campaigns for feeds ranging from ~1% to 12% arsenic in concentration. This paper will focus on the behaviour of arsenic in CESL’s leaching/precipitation step and operational factors that influence it, and on the chemical and physical characteristics of the subsequent iron-arsenic residue that represents today’s best available technology from a long-term sustainable (capital/operating costs, metal recovery, safety, environmental) perspective.The examples provided will demonstrate copper extractions approaching 99% and arsenic deportment to residue of 99%. Instantaneous settling rates of the residue were measured at 15+ m/hr. Data from subsequent short and long-term stability testing of the residue confidently support the view that the scorodite-bearing residues from the process will be stable and provide an acceptable arsenic management practice. The technology offers increased revenue and environmental certainty for miners, smelters & refiners to support the development of metallurgically challenged copper-arsenic deposits. Furthermore, results will be presented demonstrating the technology’s ability to successfully incorporate hazardous arsenic containing smelter by-products such as dust into the process feed and simultaneously extract copper value while fixing the arsenic in a stable residue."

Jan 1, 2016