Search Documents

By M. Santaluce

"The revamp of critical process assets that require a significant plant outage (shutdown) presents a unique and demanding set of challenges for plant operators. They are executed in a more complex Brownfield environment, typically with limited working space and often involve unknown conditions or scope. For plant operators, such a project is often a high cost event both in terms of opportunity cost of lost production and the resource cost of labor and materials. It can also be a high risk event in terms safety, environment, and future plant reliability/availability. This impacts current and future performance or Overall Equipment Effectiveness (OEE). In our experience, the sequential nature of the EPCM approach does not provide the proper framework to facilitate the level of coordination, stakeholder cooperation and detailed planning required to adequately address the construction and shutdown complexity of a critical asset revamp projects. This paper proposes a more integrated approach to handling shutdown revamps of critical assets. Its main thesis is to involve the key performing stakeholder groups early in the project lifecycle (engineering team, procurement team, construction team and plant operations) to form an integrated shutdown management team that is focused on ensuring delivered results are aligned with project objectives. In this model, the construction team executing the shutdown/construction is preparing the detailed shutdown/construction planning concurrently with detailed engineering and procurement planning. This allows construction/shutdown requirements to influence engineering and procurement, with the desire to optimize safety, speed, quality and cost. The paper also discusses how to overcome the procurement hurdle in applying such an approach. The outcome of this integrated approach is better planning, coordination, communication and alignment between the project stakeholders, a shutdown/construction driven planning approach that more fully addresses the challenges of these projects and delivered results that are aligned with project objectives."

Jan 1, 2015

By Zhiye Zhao, Jianping Sun, Zhipeng Xu

"The subsea rock cavern project is an underground storage facility. For cost-effective and safe excavation, the risk caused by the groundwater seepage into the rock cavern must be addressed. As one of the essential steps of the assessment work, the hydraulic conductivities of the fractured rock masses should be reliably determined based on the limited measured data and geological information from the few boreholes. On the basis of site investigation data and monitored water flow and water pressure data during excavation, this paper presents an estimation method for hydraulic conductivities of the rock masses containing water bearing zones.INTRODUCTIONIn the development of underground rock caverns/tunnels, the uncertainty of hydro-geological conditions plays a critical role in terms of construction cost and construction safety. Excessive groundwater seepage has been identified as one of the key safety factors which always lead to vast loss, such as the Seikan Tunnel in Japan which encountered sudden water inflow and then catastrophic face collapsing, tunnel flood during excavation (Xu et al., 2013). As a key factor in the risk management associated with the groundwater leakage into rock cavern, the hydraulic conductivity determination is very important for cost estimation, reliable water control and construction management.The case presented in this paper is an underground project consisted of a cluster of rock caverns/tunnels for storage of hydrocarbon products. These caverns are located in heterogeneous sedimentary bedrock, at a depth of 130 m beneath a basin, and the crowns of caverns are located at about 100 m below the sea bottom. The caverns/tunnels are designed at two levels, the water curtain tunnels are at the upper level, and oil storage caverns are at the lower level, as shown in Figure 1. A number of horizontal and vertical water injection holes drilled from the upper water curtain gallery tunnel will establish continuous horizontal and vertical water curtains for providing a stable pressure distribution around the caverns, to keep oil/gas inside the lower storage caverns. As the hydrostatic pressure of groundwater around the storage caverns is higher than the pressure of stored oil and gas, the stored oil and gas will not leak out of the cavern (Lu, 2010; Xu et al., 2015). Groundwater pressure gauges are installed in the water curtain gallery tunnels, and water from the operational and access tunnels is injected continuously into the curtains to maintain the pressure. Some monitoring data are recorded at different construction stages. This paper proposes suitable methods to predict the hydraulic conductivity in rock mass and to determine the hydraulic conductivity in the water bearing zones."

Jan 1, 2015

By Aidan Giblett

"It is important to make a clear distinction on the scope of work of the Global Mining Standards and Guidelines (GMSG) guideline for sampling grinding circuits. Many mineral processing practitioners are familiar with the sampling and surveying of comminution circuits, in particular grinding circuits, for performance diagnosis and the identification of optimization potential. These surveys often provide information for population balance modelling of individual comminution and classification unit processes, and consequently require a large amount of information to calibrate and validate the unit models. As a result, these surveys are labour intensive, somewhat expensive, depending on internal capabilities of the mine site or company and have a long time span from initial planning to final reporting. They also require a high level of expertise to process the survey data, simulate the circuit and make sensible recommendations on follow up actions.As a result of these factors, full grinding circuit surveys are not a common occurrence at a large number of processing facilities, and several years may pass before follow up surveys are conducted. In the ensuing gap between surveys, the efficiency of the grinding circuit must often be taken on faith, and this is considered an unacceptable lapse in an environment of strained natural resources and low commodity prices.To support the rapid and productive energy efficiency analysis being promoted by the ICE working group, a much simplified survey and analysis process is required. The process reflected in the GMSG guideline is indeed more conducive to frequent analysis, at a skill level that is well within the capabilities of the average plant metallurgist. As a result, it becomes feasible to conduct mini-surveys of plant performance, which can be used to quickly and precisely diagnose the high level impact of process changes. These methods can also be manipulated by an experienced practitioner to provide sufficient information for modelling of the circuit to estimate the impact of process changes, allowing an initial rate and rank exercise to focus plant optimization efforts."

Jan 1, 2015

By L. H. Chen, Y. C. Chen, Leo Benyamin, W. C. Chen

"To investigate the evolution of fluid-driven fracture of rock-like material subjected to borehole fluid pressure and its consequential damage with regard to post-peak stabilization, micro-seismic activities have been monitored using nondestructive technique of acoustic emission (AE) corresponding to the macro-scale complete history of loading curve by setting the hollow cylindrical external circumferential strain to be a closed-loop feedback signal during servo-fluid-driven tests. Development of a novel fluidinduced loading system injected from internal borehole as well as monitoring system were equipped such that the initiation and propagation of micro-cracks enable to analyze experimentally. By programming/controlling either injection rate or fluid pressure, synthetic sandstones with low-permeability made by cement mortar were conducted in this study. It found that both the growth of macro-crack initialized intensively as reaching the breakdown pressure and the micro-seismic activities represented by AE locations show nice agreement. The experimental results in this paper provide better understandings of fluid-driven fracture mechanism.INTRODUCTIONFluid-driven fracture is a process of generating cracks by injecting viscous fluid into solid material. Conventionally, fluid-driven fracture tests have been performed by mining industry to measure the in situ stress (Haimson & Fairhurst, 1969) and fluid-driven fracture has been employed by the petroleum industry to recover oil and gas. Additionally, the mechanism of crack growth or the extension of existing cracks is important to the evolution of volcanic dikes over distances of a few kilometers (Lister & Kerr, 1991; Rubin, 1995), crack propagation in dams (Bolzon & Cocchetti, 2003) and the disposal of radioactive waste (Sun, 1969)."

Jan 1, 2015

By A. Noble

"In coal and mineral processing, several numeric parameters are used to quantify the separation performance of unit operations. For density-based separations, the partition curve is used as the starting point for many stages of diagnostic analyses. The curve is often quantified by its midpoint slope sharpness, and this single value is subsequently used for technical evaluation, benchmarking, and comparison. While this analytical approach does depict misplacement by relative density class, it inherently prioritizes middling separation and does not consider process economics or the micro-price value of individual classes. Alternatively, the organic efficiency parameter does consider process economics; however, it does not reveal information on the root cause of lost revenue or misplacement. In this paper, a new analytical approach is introduced which reconciles the technical misplacement data derived from the partition curve with the economic data derived from micro-pricing. The result is a new analytical procedure which reflects a better use of performance data. INTRODUCTION Partition curves are commonly used in the characterization, evaluation, and simulation of various physical separators. In mineral processing, partition curve analysis is routinely applied to hydrocyclones, screens, and density separators. Graphically, the partition curve depicts the recovery of particles as a function of a physical property on which the separation is based (e.g. particle density, size, magnetic susceptibility, etc.). Given the probabilistic nature of many real separators, the partition curve often exhibits a characteristic “S” shape (Fig. 1), similar to a cumulative normal distribution. Other geometric features of the curve are also depicted in Fig. 1, including the high and low closeout (or bypass) values, the midpoint slope, and the separation cut point (property value with 50% recovery). Partition curve analysis was originally proposed to evaluate coal washability (Tromp, 1937). Given the limited computational resources at the time, the analytical methods relied heavily on graphical construction and interpretation of the curve. Owing to the simplicity of the calculation and interpretation, many of these graphical approaches are still widely used for performance analysis today. The most common calculations are based on the slope of the partition curve at the midpoint. Increased slopes correspond to enhanced separation performance, since a perfect separation exhibits a stepwise transition from 0 to 1 at the desired cut point (i.e. an infinitely large slope). One common formulation of this slope, the Ecart Probable (Ep), is derived by evaluating the slope between the 25% and 75% recovery points:"

Jan 1, 2015

By S. Peng, N. Vayenas, A. Farah

"While genetic algorithms have been widely adopted in ore grade estimation and optimization, mine design, and production scheduling in the mining engineering field, reliability and maintainability analysis of mining equipment using genetic algorithms has been a relatively new research area in recent years. This paper presents an application of genetic algorithms using case studies with seven underground scoop trams whose maintenance records have been collected over a period of 12 months from an underground mine in the Sudbury mining area. Based on the assumption that various factors that contribute to machine failures resemble the biological evolution process, the authors have developed an in-house PC software application called GenRel which adopts genetic algorithms in its programming. In this study, the authors feed the historical maintenance data into GenRel in order to predict future maintenance characteristics of mining equipment in a time period of three months. Then the predicted maintenance characteristics are compared to the actual maintenance records in the same time period. A statistical study is then used to examine the similarity between the predicted data and the recorded data.INTRODUCTION Today maintenance costs of sophisticated engineering systems are so high that maintainability draws great attention from scientific researchers to operations managers. For instance, a study by [1] shows that American manufacturers spend more than 300 billion U.S. dollars on plant maintenance and operations. Therefore it is understandable that the main objectives of applying maintainability principles to engineering systems are to reduce projected maintenance costs, to use maintainability data to estimate system or equipment availability/unavailability and to determine labor-hours and other related resources needed to perform the projected maintenance. A system with better maintainability would inherently provide the benefit of lower maintenance costs, less time to recover with lower breakdown frequency (design for simplicity), less complexity of maintenance tasks and relatively reduced man-hours [2]. Most maintainability functions use the Time To Repair (TTR) as the independent variable. It is common to use probabilistic or statistical concepts to define a maintainability function, for example, the probability density function. Let t denote the time. Assuming a repair starts at t=0 and completes at time T, the maintainability can be mathematically defined [3] as in Equation (1)."

Jan 1, 2015

By Erika Moonin, Jim Nickerson, Claudio Cimiotti, Roberto Bono

"In response to the severe drought on the Colorado River basin and in order to preserve existing water capacity to the Las Vegas Valley, the Southern Nevada Water Authority contracted a new deep-water intake (Intake No. 3) located in Lake Mead. The current project (Contract No. 070F-01-C1) includes 5 km (3 miles) of tunnel with very difficult geological conditions and a 200- m (650-ft) deep shaft and marine works. This paper will present the current status of the design-build contract being constructed by Vegas Tunnel Constructors and the challenges and problems faced and the innovative solutions developed to handle the difficult conditions encountered during tunneling with up to 15 bars of pressure.ProjectbackgroundThe Las Vegas Valley receives the majority of its water from Lake Mead, which is located approximately 30 km (20 miles) east of the Las Vegas, NV metropolitan area. Due to the severe drought that has hit the southwest region of the United States, the water level in Lake Mead has receded from its high water level of 372 m (1,221 ft) above mean sea level (amsl) to a low of 330 m (1,076 ft) amsl in June 2015. Should the lake level continue to fall, at elevation 320 m (1,050 ft) amsl, the current water intakes will not be able to draw enough water to meet the needs of the local area. The risk of losing water capacity has prompted the construction of a new deeper intake. Not only is the new Intake No. 3 situated at a lower elevation in the lake at 262 m (860 ft) amsl, the new Intake No. 3 is also located to draw better quality (Fig. 1).Project challengesThe project has had several difficult challenges to overcome:• The work consisted of a 1.2 kt (1,300 st) structure constructed on a barge and lowered 100 m (330 ft) into Lake Mead anchored with 9,200 m3 (12,200 cu yd) of tremie concrete.• The drill-and-blast starter tunnel was impacted by three inflow events, resulting in a one-year project delay.• One of the main challenges was selecting the tunnel boring machine (TBM) and excavating the tunnel with expected hydraulic head pressure of as much as 17 bar (16 bar was the highest pressure recorded during the drive), crossing faulted areas, low rock cover and the risk of tunnel instability due to direct connection with the lake.• Extensive pre-excavation grouting with a constant head pressure ranging from 12 bar to 15 bar.• Structural repair of the cutterhead in difficult hydrogeological conditions [water inflow of approx. 800 m3/hr (4,000 gpm)].• Complete repair of the cascade sealing system for the main bearing and two replacements of the pinion bearings.• The TBM approach to the intake structure."

Jan 1, 2015

By J. Andres, M. Cross

"Freeport-McMoRan’s Sierrita operations has two natural gas-fired molybdenum roasters for converting molybdenum disulfide into molybdenum trioxide. When these roasters were compared to other similar units within the company during a benchmarking exercise, it showed that increased throughput from the roaster units at Sierrita was possible. A team of site metallurgists, technical experts from other sites, and engineers from the Climax Technology Center was formed to study the potential in more detail. The team investigated many parameters in the roaster, including temperature profiles, roaster chemistry profiles, rabble and drop hole patterns, and operational strategies. The results of these studies and the associated throughput improvements are described in this paper. INTRODUCTION Molybdenum, a vital component for the steel industry, is typically found in nature as molybdenum disulfide (MoS2). MoS2 is typically recovered via flotation processes and is purified through leaching processes. While molybdenum disulfide is a commercial product, it is not the form of molybdenum that the steel industry requires. They require molybdenum in the form of molybdenum trioxide, MoO3. There are multiple ways to refine molybdenum disulfide into molybdenum trioxide. The primary method is the oxidation of molybdenum disulfide in a multiple hearth roaster. The chemistry of converting molybdenum disulfide to molybdenum trioxide is very favorable at increased temperatures, oxidizing the molybdenum through a range of exothermic reactions to ultimately produce MoO3. The chemical reactions that occur in molydenum roasting occur in three zones. These three zones correspond with four different reactions."

Jan 1, 2015

By V. Maazallahi, A. Rouleau, A. Saeidi

"The geometry of the terrain topography before and after the failure are the essential factors for analyzing a landslide and for the design of remedial works. This paper presents a method to determine these factors, considering that the determination of the slide surface profile is difficult and costly using traditional methods and the pre-slide topography data is often not available. The presented method to locate the 3-dimensional geometry of the slide surface is based upon determining the slide surface in 2- dimensional vertical sections. This method utilizes post-slide topography of the area to determine the pre-slide topography and uses equations to estimate the pre-slide situation using a statistical process applied to points located on the sliding mass. This method is tested on the Maskun landslide in Iran. The results indicate the applicability of the proposed method to obtain the key factors for the back analysis of a landslide in a cost effective manner.INTRODUCTIONProbably the most reliable method of determining the strength of soil and rock mass is to back analyze a failed or failing slope (Caia et al. 2007; Wyllie & Mah, 2004). This method is used in geotechnics for estimating geotechnical parameters of the rock and soil mass (Sakurai et al., 2003; Frayssines and Hantz, 2009; Cepuritis et al. 2010), but it requires that the failure mode is well established and that there is complete and precise information available on the slide surface and the sliding mass (Sjöberg, 1996). Measurement of the slope profile before failure provides the basic information required for a back analysis (Hock & Bray, 1981). The post-slide topography is another key factor. The back analysis process for determining the actual strength parameters of soil or a decomposed rock mass after a landslide requires knowledge of the sliding mass geometry, both before and after the sliding event. Many studies are reported in the literature about the application of back analysis for determining geotechnical and geomechanical parameters of rock and soil mass (Sakurai et al., 2003; Cepuritis et al. 2010; Frayssines and Hantz, 2009, Hussain and Stark, 2011), but they generally present little information about the geometry of the slide surface, and the weight of rock and soil mass that slid, although these factors are the most important parameters for back analysis process. Liang and Xue-song (2012) determined the slip surface having the minimum factor of safety (called critical slip surface in deterministic analysis of slopes) and the slip surface with the minimum reliability index (called critical reliability slip surface), but they have not considered the actual profile and geometry of the slide surface. Rocscience (2013) proposes the back analysis option in the Slide software for slope stability study, but it requires an imposed slide surface as input; alternatively, one can estimate by a finite element analysis the surface with the minimum factor of safety. However, this estimated surface is very likely different from the actual sliding surface, considering the uncertainties in input data of the finite element method."

Jan 1, 2015

By M. Feinendegen, Ph. Siebert, C. Clauser, K. Willbrand, M. Ziegler

"Three institutes of RWTH Aachen University collaborate on laboratory tests and numerical simulations of hydraulically driven fractures in igneous rocks. The project´s target is to enhance the understanding of hydraulic induced fractures for deep geothermal energy exploration. Based on the idea of creating new discrete fractures in hot dry rock (HDR) reservoirs, the current project stage deals with this process on a laboratory scale. Especially for this purpose, a new testing facility has been developed and laboratory tests are performed to verify a hydraulic fracture propagation code based on the extended finite element method (XFEM). The testing facility enables us to initiate and propagate fractures in large samples of dense rock under triaxial confining pressures and to monitor the fracture propagation by extensive measurements. This contribution gives a short introduction to the project‘s background and mainly focusses on the test facility, the experimental procedure and exemplary results.INTRODUCTIONThe most efficient technique to increase the permeability of subsurface rock is to initiate and open fractures by applying hydraulic pressure from a packed borehole-section and to inject fluid into these fractures to propagate them. Since its first use in petro industries to enhance the production of wells in natural gas and oil reservoirs, the interest in targeted creation of hydraulic fractures has increased exponentially. As the key technology to the extraction of unconventional gas from shale, hydraulic fracturing (HF) became a major topic in a heated public debate. Based on the fact that a fracture tends to propagate in a direction perpendicular to the minimal principal stress, hydraulic fracturing has become an established tool for estimating geological stress states in almost any depth. Enhanced geothermal systems (EGS) in HDR reservoirs use engineered fractures as a heat exchanging system for a cycling fluid driving a power plant."

Jan 1, 2015

By Stefan Larsson, Jan Ekström, Jennie Kock-Larsen, Håkan Garin

"This paper describes the testing procedure (or protocols) for quality control of dry deep mixing columns in a major ground improvement project carried out in Sweden. Quality control was mainly based on column penetration tests performed at different stages in the project and on two occasions after installation. In the paper, the results from the tests are compared with tests on the unimproved clay. As expected, the results show that the correlation between undrained shear strength in the columns and in the unimproved soft soil depends mainly on the in-situ stress. However, the correlation probably depends on when the tests were performed after mixing. When the influence of the in-situ stress was excluded from the analysis, no significant correlation could be identified. This means that the undrained shear strength in the columns and in the unimproved soft can be considered to be uncorrelated when the strengths and the corresponding variability are evaluated with depth from groups of tests.INTRODUCTIONQuality control and quality assessment of deep mixing (QC/QA) constitute a key component in verification of the limit state design. Due to the complex mixing process and varying geological conditions, it is normally not possible to sufficiently assess the strength and deformation properties in advance. In Sweden, the most commonly used QC/QA method for verification of the limit state is the column penetration test (Axelsson and Larsson 2003; Bergman et al. 2013). The method works well but is time-consuming and requires many tests since property variability is normally high. The column penetration test can be used to assess the undrained shear strength Cu,col. However, it is not clear how the strength correlates to the undrained shear strength of the unimproved soil Cu,soil. There are common factors such as the in-situ stress state and the natural water content, which makes a positive correlation probable, i.e. as Cu,soil decreases, Cu,col also decreases and vice versa. The unimproved soil has a natural spatial variability, but it is not known if the improved soil follows the same variation. The mixing process has a substantial influence on the strength variability and may supersede the influence of other factors. However, if a sufficiently good correlation exists between Cu,col and Cu,soil, information from the geotechnical ground investigations can be used in the design and planning of QC/QA of deep mixing in a more stringent manner. Information about the correlation is also essential in reliability based design, where a strong positive correlation may have a negative influence on reliability. However, as discussed by Al-Naqshabandy and Larsson (2013), this correlation may be weak or insignificant for a representative failure domain where the mixing process may have a dominant influence on the strength variability. It is thus of interest to assess the correlation."

Jan 1, 2015

By J. García, B. Arango, F. Calderón, O. J. Restrepo-Baena, A. Carreno, L. Rojas-Mendoza, J. Pérez, E. Bedoya

"Tungsten extraction is a subject of global interest due to is properties. These properties, such as its high melting point, have contributed to the development of metallurgical extraction processes that can be adapted to the particular chemical composition and mineralogy of the ore. In Colombia there is a research deficit in tungsten related areas, and especially with regard to its extractive metallurgy. In this study the physical, chemical and mineralogical characterization of a sample were performed. Subsequently, crushing and grinding were employed to reduce the material to a more convenient size, making it suitable for further concentration and metallurgical processes. Through physical concentration techniques it was obtained a concentrated ranging between 60 -70 % of WO3 content.INTRODUCTION Tungsten is a metal of great economic importance due to its excellent properties such as high density and extraordinary melting point 3422°C), which is indeed the highest of all the elements. Tungsten is primarily used in metal alloys, manufacture of special steels, coatings and catalysts; products of interest to both international and national industry. However; given that the use and economic value is determined by the percentage of tungsten in the mineral, particle size and chemical associations, it becomes essential to properly characterize the mineral to further define possible metallurgical extraction routes. The metallurgical processes for minerals enriched in tungsten may vary depending on location and the genesis of the ore body, which means that for each ore a particular set of operating conditions must be determined. This is important since process standardization can lead to misuse of the mineral resource. However, in Colombia there is a research deficit as it relates to minerals enriched in tungsten and to its extractive metallurgy. Then, there is a need to conduct studies that can lead to a better understanding of the ore, and to develop extraction processes for the metal of interest. EXPERIMENTAL A state of the art review was made in order to gain insights of the tungsten metallurgical process. Comminution was necessary with the aim to reduce the sample size; therefore the sample was taken into crushing and grinding stages. Concentration techniques such as magnetic separation, gravity and / or electrostatic were also applied. Physical, chemical and mineralogical characterization were performed by using polished sections, grain size determination, X-Ray Fluorescence (XRF) and X-ray diffraction (XRD) techniques."

Jan 1, 2015

By Félix Lewandowsky

El presente texto describe las actividades para corregir los pasivos ambientales heredados y asumidos bajo responsabilidad de la Compañía Minera Colquirrumi S.A. Para ello, se elaboró un plan de cierre de los cuatro depósitos de los relaves de Hualgayoc donde se busca mostrar los criterios utilizados, los estudios de ingeniería y la forma cómo se ejecutaron las obras de cierre definitivas de los depósitos de relaves.

Jan 1, 2015

By F. J. Macias, A. Bruland, F. E. Dahl

"Tunnelling by use of Tunnel Boring Machine (TBM) is gaining a greater presence as a suitable excavation method. Disc cutter consumption has a strong influence on performance and cost when using TBMs and the influence becomes even more relevant in hard rock. Furthermore, good predictions of TBM performance and cost facilitate the control of risk as well as avoiding delays and budget overruns. Since abrasive wear is the most common process affecting cutter consumption, good laboratory assessments are needed. A new abrasivity test method called Rolling Indentation Abrasion Test was developed. The goal of the new test design and procedure is to reproduce wear behaviour on hard rock tunnel boring in a more realistic way than traditionally used methods by introducing wear by rolling contact on intact rock samples. INTRODUCTIONHigh investments are involved in the tunnelling industry, especially in Tunnel Boring Machines (TBMs) projects. Performance predictions and cost estimations are crucial for planning and risk management of TBM projects. Cutter consumption has a large influence in terms of time and cost, and an even greater effect in case of hard rock projects. Many factors are influencing the amount of cutters consumed in hard rock TBMs. Normal TBM operation results mainly in abrasive wear on the cutters and appropriate methods for abrasivity assessment are needed. Rock abrasiveness cannot be considered as an intrinsic property and the complete tribological system should be considered in addition to the geological properties of the rock.In the present paper, a new test method for abrasivity assessment in tunnel boring called Rolling Indentation Abrasion Test (RIAT) is presented. The traditionally used test methods for determination of rock abrasiveness uses sliding or impact contact in order to cause wear while the RIAT introduces rolling contact on intact rock samples. The ambition of the new test device is to have a reliable method to evaluate the cutter wear in hard rock tunnel boring by reproducing wear behaviour on rolling disc cutters in a more realistic way. It has been established by many authors that the abrasion of a cutter ring is proportional to its rolling distance (Rostami, 1997; Bruland, 1998). In the present work, the weight loss of a mini-cutter ring is measured subsequent to testing in order to evaluate wear in the rolling process and could hence be related to cutter ring wear. Indentation of the tools in the intact rock sample is considered as an indication of the surface hardness of the rock or the resistance to indentation by rolling."

Jan 1, 2015

By Yi Yang, Mark Zoback

"We report laboratory studies of the time-dependent deformation of core samples from four different formations in the Williston Basin - the Lodgepole formation, the Middle and Lower Bakken formations and Three Forks formation. The laboratory tests reveal varying amounts of viscoplastic deformation in response to applied differential stress. The time-dependent deformation is generally greater in rocks with higher clay and organic content, and can be described by a power-law function. Because the magnitude of the creep strain is linearly proportional to the applied differential stress, we can utilize viscoelastic theory and geophysical logs to estimate the degree to which tectonic stress is affected by viscoplastic stress relaxation. We suggest that viscoplastic stress relaxation results in the Upper and Lower Bakken Formations act as frac barriers during hydraulic fracture stimulation in the Middle Bakken, but the Lodgepole and the Three Forks Formations are not frac barriers.INTRODUCTIONHorizontal drilling and multi-stage hydraulic fracturing in shale reservoirs are critical for successful exploitation of ultra-low permeability shale gas, tight gas and shale oil reservoirs. Characterization of the mechanical properties of the reservoir rocks is essential to understanding the behavior of rocks during drilling and completion. Previous laboratory studies have shown that the timedependent deformation in clay-rich shales can be characterized as linear/viscoelastic deformation (Chang et al., 1997; Hagin and Zoback, 2004a, b; Sone and Zoback, 2013b, 2013c). Sone and Zoback (2013c) showed that laboratory measurements of time-dependent deformation in various gas shale reservoir rocks, and demonstrated that the viscoplastic deformation of these rocks can be characterized by a power-law function. They interpreted the results in the framework of linear viscoelastic theory to quantitatively assess the geomechanical effect of viscous time-dependent deformation over engineering and geological time scales. (Sone and Zoback, 2014) further extended the theory and proposed a viscous relaxation model that can be applied to predict the continuous differential stress magnitude using the geophysical logs. They tested the validity of their model by comparing the stress prediction with the occurrence of drilling induced tensile fractures (DITFs) and the vertical hydraulic fracture penetration observed from microseismicity."

Jan 1, 2015

By A. Hartikainen, M. Rinne, F. Johansson, R. Yorke, L K. T. Uotinen, E. Korpi, J. Antikainen

"In order to determine the in-situ shear strength of rock joints, large scale testing is required. However, this is both expensive and difficult to execute. One possible method to overcome this may be to use photogrammetry to capture large joint surface roughness in-situ and downscale it to replica samples, which could be sheared in laboratory. In this paper, as a first part in such a method, a technique to digitize surface roughness and to produce replica samples for laboratory shear testing from a larger joint sample are presented. First, a thin granitic rock slice with dimensions of 1.75 m x 0.95 m of granitic intact rock was chosen for the study. The joint surface is fresh and created through tensile induced splitting. The large joint sample is digitized using photogrammetry. Then, one fullscale 1.7 m x 0.6 m geometry is cropped from the digitized joint geometry and then subsamples at 10x, 7.5x, 5x, 2.5x and 1x scales. All sub-geometries are scaled down digitally to produce 0.17 m by 0.06 m geometries. The geometries are used to make casting molds both positive and negative to produce samples with perfect matedness. The casting molds are 3D printed in polylactic acid plastic and C60/75 concrete is cast to produce a replica series. In addition to the creation of this replica series, two pilot replicas are also tested using a portable shear box with a 0.5 MPa normal pressure. The results from the pilot rounds are presented and discussed. Finally, suggestions for future research are given.INTRODUCTIONThe rock mass strength is in many cases controlled by the shear strength of rock joints, especially in hard rock masses. The shear strength is generally found to be influenced by several parameters, including normal stress, the basic friction angle of the intact rock, the joint surface roughness, the joint wall compressive strength, the matedness of the joint surfaces, weathering and infilling. The effect of these parameters for the joint shear strength can be evaluated in laboratory scale. However, the shear strength is known to be scale dependent. How the scale effect influences the strength is not fully understood. The general consensus is that the shear strength decreases when sample size increases, i.e. a negative scale effect (Bandis et al. 1981). However, some studies have presented contradictory results, see for example Hencher et al. (1993) and Kutter & Otto (1990). The extent and nature of the scale effect is still a question of debate (Tatone & Grasselli 2013)."

Jan 1, 2015

By P. R. La Pointe, J. Clark

"Studies have shown that the roof in coal mines is nearly twice as likely to fail at intersections as at entries due to enlarged roof spans, stress redistribution and other factors. However, the relative stability of intersections in a mine varies, and an improved understanding of what factors impact roof instability can lead to efficient, proactive mining practices that both enhance stability and mining efficiency.A study was undertaken at an underground longwall coal mine to develop a model to predict the stability at the intersections of entries and cross-cuts. The statistical analyses relied upon observational and measured data regarding the development of tension cracks, seepage, intersection geometry, mining practices, geological attributes and geomechanical factors at 783 intersections. Each intersection was given a NIOSH roof. Common data mining techniques, such as multivariate linear regression, multinomial logistic regression, decision trees and probabilistic neural nets, were considered and evaluated to establish correlations and associations between stability and the other variables. Two of the more successful techniques were Decision Trees and Multinomial Logistic Regression. The analyses showed that a number of factors impacted stability:• Overburden thickness (impact on stress concentration magnitudes)• Initial opening area (impact on stress concentration magnitudes)• Sulfur content (depositional environment & impact of mechanical properties, leaching effects)• Intersection type (impact on stress concentrations)• Gob distance (impact on stress concentrations)• Presence or proximity of a particular sandstone (impact on mechanical properties)• Roof bolt type and diameter (impact on reinforcement)Some factors showed no statistically significant relation to stability. These included:• Total area• Supported areaSeepage was a more problematic variable in assess. Seepage is associated with instability, but it is not clear whether seepage occurs as a consequence of instability, for example, through the creation of tension cracks, or whether the intersection has been excavated where water already exists and has degraded the rock prior to excavation, leading to greater instability.Seepage appears related to the geology of the roof rock mudstones, not the sandstones. Tension cracks in the intersections occur preferentially where the Sulfur content is below 0.9%. The Sulfur may relate to mechanical differences in the roof rock, and where the Sulfur is low, the roof is less stable, there are more tension cracks, and seepage is greater. This suggests that the weaker mudstones may be more prone the development of tension cracks, not because these rocks are more brittle, but possibly weaker.2-way and 3-way intersections appear to have less seepage than 4-way, although very few intersections overall have any seepage. This is similar to the roof stability, in which the 2-way and 3-way are more stable. 2-way and 3-way intersections have fewer-than-expected tension cracks, while 4-way have more than expected. These results suggest that four-way intersections are weaker and more prone to tension crack development, also suggesting that increased seepage results from weaker roof conditions, rather than the converse. Thus seepage appears to be mostly a consequence of instability rather than a cause and is higher where there are 4-way intersections, mudstone geology and external loading factors like depth of cover and proximity to gob that promotes crack development. The study also indicated that a better understanding of the mudrock facies could reduce uncertainty."

Jan 1, 2015

By K. Soucek, J. Ptácek, A. Hastíková, R. Kukutsch, P. Konícek, P. Waclawik

"Cable bolts are used frequently as a secondary support system (with steel arch support) in difficult stress-strain conditions of deep coal mines. The load transfer mechanism of cable bolts depends on several factors, such as the strength, deformation and geometric properties of the bolts, resin and the surrounding rock mass so-called cable-resin-rock system (CRR system). The bonding length and bolt/borehole diameter ratio strongly influence the final bearing capacity of the CRR system.The study presents the behaviour of CRR system during a pull-out test which is usually used in the carboniferous rock mass in the Czech part of the Upper Silesian Coal Basin. A series of 28 pull out tests were performed on 3-m-long cable bolts, with various combinations of borehole diameters and bonding lengths, to understand this behaviour. Boreholes were drilled into a solid rock mass consisting of fine-grained sandstone to guarantee similar conditions during the pull-out tests. Video inspection and measurement of borehole diameters were performed to determine their quality and real diameters. Three characteristics were observed from pull-out test results: ultimate pull-out load; displacement of the end of bolt and system stiffness. Numerical modelling by FEM (Finite Element Method) was used to determine the stiffness of the CRR system for variable bolt/borehole ratios and bonding lengths each under constant load. A linear elasto-plastic model and a mohr-coulomb model were used for cable and resin-rock respectively. The results of the experiment may contribute significantly to improving of the methodology of cable bolts installation as well as the design of used cable bolts."

Jan 1, 2015

By A. S. Ibrado, D. W. Fuerstenau

"Gold, silver and copper form various complexes with cyanide, of which only the singly charged dicyano form adsorbs appreciably on activated carbon. The adsorption of the dicyano complexes appears to be controlled predominantly by chemical reaction at the surface of a shrinking unreacted core. Metal uptake over time is non-linear, which eliminates control by boundary layer diffusion. The rate of adsorption is not enhanced by a reaction interruption, which suggests the absence of concentration gradients in the pores. Finally, the rate of adsorption increases with decreasing activated carbon size in a manner consistent with the shrinking core model. The results of this investigation accentuate the importance of efficient acid washing of carbon and removing carbon fines from the barren carbon stream. INTRODUCTION With the dwindling reserves of high-grade ores, most of the world’s gold is produced from low-grade ores by cyanide leaching. In the past, leaching was followed by the Merrill-Crowe process, in which gold is precipitated from clarified pregnant solutions by zinc cementation. This process is still being used for high-silver ores, where the cost of carbon stripping becomes prohibitive. For deposits with silver-to-gold ratios of about 4 or less, adsorption on activated carbon would be the usual solution purification step taken. The process simplifies solid-liquid separation and offers a viable solution to preg-robbing organic carbon in some ores. The modern industrial application of carbon adsorption started with the carbon-in-pulp (CIP) process, where carbon adsorption was used mainly as a solution purification step. In 1973, Homestake Mining Company commissioned the first large-scale CIP plant in the U.S.A.1 Later, carbon was added earlier in the circuit to control preg-robbing by adsorbing gold cyanide onto activated carbon as soon as it is dissolved. The scheme is successful because activated carbon is a stronger adsorber than the organic carbon found in preg-robbing ores. This process came to be known as the carbon-in-leach (CIL) process. Numerous research investigations have been performed on the chemistry involved in the CIP process, which at the time of its introduction was not clearly understood. Of these, research on the kinetics of adsorption probably bears the most immediate impact on industrial practice,2,3 where adsorption systems rarely reach equilibrium, if at all, and slight slowdowns in the adsorption rate can translate into significant decreases in revenue. To illustrate this, organic compounds, like flotation reagents, have been known to impair CIP circuits. However, laboratory tests showed that the organic compounds do not significantly affect the adsorption capacity of activated carbon. Rather, the harmful effect may be attributed to a lowered adsorption rate.4,5 Also well known is the faster rate at which fine activated carbon powders reach equilibrium compared to coarse activated carbon, even though the final (equilibrium) amount of material adsorbed per unit weight is the same."

Jan 1, 2015

By K. Bommer

"In today’s fast paced, globally competitive world, reliability and machine uptime are of the utmost importance to a successful operation. Along with these targets more emphasis is being put on cost reduction and decreasing the environmental impact of the overall system. To achieve these goals, automatic lubricators and lubrication systems have been used in many industries for years and are now becoming a common tool in the mining industry as well. These systems are able to provide proper lubrication amounts at the proper times autonomously, helping to keep the machines running smoothly while minimizing the physical support required. Copper mines in the southwest have begun utilizing auto lubrication to avoid mistakes and unplanned shut downs on critical equipment. This paper will describe the engineering behind these products and review case histories where these tools have been successfully utilized in the mining industry. INTRODUCTION In a dirty, dusty, wet environment, where machine uptime is imperative, proper lubrication of bearings is the only way to survive. With the push for cost reduction and mines striving to lower their environmental impact and increase worker safety according to MSHA guidelines, the old lubrication practices have come under scrutiny. It is no longer encouraged or cost effective to have maintenance personal walk from point to point throughout the entire mine pumping a shot of grease into each bearing once per shift. Automatic lubricators and lubrication systems have been on the market for years but recently, as the market focus has changed and technology has developed, the use of these systems has begun to rise in the mining industry. Automatic lubrication systems can be as simple as a single point lubricator lubricating one (1) bearing or a more complex system lubricating numerous bearings. With system design, the automatic lubricator provides a preset amount of grease to a bearing at regular, predetermined intervals. The systems designed to lubricate more than one bearing contain grease pumps of some design and possibly PLC controllers which can be used to remotely adjust and monitor the system. As can be seen in Figure 1, the right amount of lubrication can be achieved much more reliably with automatic lubricators. Depending on application needs, the market now has products to fit almost every wish list. This paper is going to focus on the single point systems that are lower in cost but are still being effective."

Jan 1, 2015