Search Documents

By H. Huang, Y. Takasaki, R. N. Gow

"The presence of enargite (Cu3AsS4) is problematic in gold processing not only because it is environmentally hazardous due to its arsenic content but also because it is refractory, causing both cyanide and oxygen consumption to increase. Selective leaching and treatment of the arsenic would prove advantageous prior to applying conventional gold leaching methods. The reactivity of enargite samples from Butte in Montana and Quiruvilca in Peru were spectroelectrochemically studied under alkaline conditions – pH range of 8-13 – using Raman spectroscopy and cyclic voltammetry. Raman spectra of the surface were collected during and after potentially cycled voltammograms in order to determine and compare surface species against theoretical EH-pH diagrams constructed from mass-balanced thermodynamic calculations using STABCAL software. Under slightly oxidizing conditions, covellite (CuS) peaks were found in a short matter of time, above ~100mV vs. SHE for pH 9-13, suggesting arsenic leaching specifically occurred. At longer conditioning times, elemental sulfur was observed and tended to passivate the surface. The presence of elemental sulfur suggests that copper was eventually leached from the surface. By operating above pH 12, under slightly reducing conditions near -300mV vs. SHE, arsenic can be selectively leached as thioarsenate (AsS4 3-) or thiosulfate (AsO4 3-) without sulfur formation.IntroductionEnvironmental limitations on the pyrometallurgical processing of ores and concentrates bearing arsenic and other hazardous elements often outweigh those in hydrometallurgical processing, particularly when minerals like enargite (Cu3AsS4) are present. The hydrometallurgical processing of enargite-bearing materials can be broken down into two categories: the co-dissolution of arsenic and copper under acidic conditions, and the selective leaching of arsenic under alkaline conditions. The selective leaching of arsenic would preferably leave behind copperrich sulfide phases, typically chalcocite (Cu2S) and covellite (CuS), which then become more amenable to conventional copper (and gold) processing. Furthermore, selective leaching often employs sulfide (S2-), bisulfide (HS-) or polysulfides (Sx 2-) to first extract the arsenic as AsS4 3- and AsS3 3- (Delfini et al., 2003; Anderson and Twidwell, 2008; Tongamp et al., 2010a,b). However, hypochlorite leaching (Viñals et al., 2003; Curreli et al., 2005; Mihajlovic et al., 2007), ammoniacal leaching (Gajam and Raghavan, 1983), and finegrinding to mechanically activate the enargite surface (Balaz and Achimovicova, 2006) have been investigated to increase the normally slow reaction kinetics. Because gold ores are becoming more refractory due to increasing arsenic contents as a result of enargite, these methods are being examined more closely by the gold-mining industry."

Jan 1, 2015

By Justin Cardwell, Alyson Cartwright

"Grade estimation is the cornerstone of longrange mine planning. Pit designs, metal recovery, mining costs, reserves calculations and reporting are all dependent upon a reliable grade model. If the geology is poorly understood or the interpolation methods and parameters have been haphazardly constructed, then massive financial losses will be the inevitable outcome. Therefore, a properly trained geologist must use all of the appropriate tools available including deposit knowledge and advances in modeling technology to construct the most geostatistically and practically sound long-range block model.Certain deposits, such as the sedimenthosted deposits at Tenke-Fungurume, require an interpolation method that best suits the style of mineralization. In 2014, Hexagon Mining developed a tool in MineSight called dynamic unfolding (MSDU) that has the potential to improve upon previous Euclidean-based interpolation methods. MSDU utilizes the nonstationarity of a folded grade trend to more accurately construct variograms and improve interpolation results based upon a modeled three-dimensional surface.Geology overview. The sediment-hosted Tenke-Fungurume mining district is located in the southeastern part of the Democratic Republic of the Congo (Fig. 1). The rocks within the district are primarily dolomites and shales from the lower half of the Roan Supergroup that were mineralized by ascending pregnant copper and cobalt rich brines within a massive sedimentary basin (Cailteux et al., 2005) (Fig. 2). These oxidized brines likely found a fluid channel in the porous RSC unit. The surrounding rock units provided a redox boundary for copper and cobalt precipitation along organic rich beds, forming a massive stratabound deposit that was later broken up by several subsequent tectonic events (Dewaele et al., 2006)."

Jan 1, 2015

By Manjeet Chowdhry, Qingxia Liu, Phillip Choi, Zhenghe Xu

Computational chemistry methods, such as density functional theory (DFT), are powerful tools to quantify reagent-mineral interactions encountered in sulphide mineral flotation. A quantitative relationship between theoretically calculated parameters based on chemical structure of collectors and their reactivity with different metals/minerals can provide valuable insights for design and development of more powerful and tailor-made reagents offering enhanced metal/mineral selectivity. DFT calculations at B3LYP/6-311++G(3df,3pd) level were employed to elucidate the reactivity of neutral sulphide collector reagents, including thionocarbamates (TC), thioureas (TU), xanthogen-formates (XF), dialkyldithiocarbamates (DTC) and dialkyltrithiocarbonates (TTC) with different heavy metal ions (Cu2+, Zn2+ and Pb2+) in solution. The extent of delocalization of lone pair electrons of heteroatoms (attached directly to C in C=S) over C=S group was found to be the dominant factor in determining the collector’s reactivity. Order of reactivity was established as: TU > TC > XF > DTC > TTC. All the collectors showed superior affinity towards copper followed by lead. Unidentate binding was observed through sulphur atom except for xanthogen-formate for which bidentate binding mode was observed. Effect of nature of substituent groups at N and/or O atom on reactivity of thionocarbamate and thiourea was also investigated. The results obtained through DFT calculations are consistent with the experimental data reported in literature.

Jan 1, 2015

By Shazad Hosein, William Birch, Douglas A. Anderson

This paper will present the results of tests of a new method for assessing explosive performance using wavelet transform analysis of standard blast seismograms. The theoretical background of the method was presented at an earlier ISEE conference.

Jan 1, 2015

By W. Beres

Many non-commercial operators are currently faced with the need to operate fleets of legacy gas turbine engines. How long such engines can be kept in service safely, without replacing a significant portion of their aging structural components, has become a growing concern to engine life-cycle managers, due to uncertainties in the remaining lives of critical components of these engines. This paper describes the application of the damage tolerance methodology to predict safe inspection intervals (SII) for critical components of gas turbine engines, using components of a turboprop engine for a transport aircraft as examples. High temperature components of this engine are made of advanced aerospace alloys. The methods of predicting three-dimensional fatigue crack growth at the critical location of turbine discs and spacers using both commercial and in-house developed algorithms are presented. Sensitivity analyses are performed to determine the effect of variations in material parameters on the predicted safe inspection intervals. In addition, spin rig tests performed for both turbine discs and spacers are described. Finally, crack growth rates predicted by numerical analyses are compared to those obtained from spin rig testing and the damage tolerance of the turbine components is assessed.

Jan 1, 2015

By D. Mas Ivars, K. Suzuki, J. A. Vallejos

"A comprehensive geotechnical characterization has been undertaken at the El Teniente mine to describe and determine the rock mass behaviour strength properties of the primary copper ore. The Synthetic Rock Mass (SRM) modelling approach is used to simulate the mechanical behaviour of this heavily and unfractured rock mass. The micro-parameters of the model have been calibrated against mechanical properties and scaling laws for intact rock and veins, in order to represent virtual samples of four different geotechnical units. Results can be used to predict the rock mass scale effects, anisotropy, and brittleness properties that cannot be obtained using empirical methods.INTRODUCTIONThe primary copper ore at the El Teniente mine is described as very competent and massive, given that it exhibits a brittle behaviour (Rojas, Cavieres, Dunlop, & Gaete, 2000). This description is coherent with the geological description of the rock mass, which does not have discontinuities match as the definition provided by International Society of Rock Mechanics (ISRM, 1981). Only faults can be classified as discontinuities, but they are widely spaced. The primary copper ore has a high frequency of veins, where the cooper mineralization is hosted, these vein network structures are known as stockwork. Soft veins containing weak minerals as infill (chalcopyrite and anhydrite) control the disassembling of the rock mass during caving (Brzovic & Villaescusa, 2007).Presently, there are mainly two traditional methods used to estimate the strength of the rock mass: 1) determination of the strength envelope of the rock mass using scaling parameters from laboratory tests and 2) using numerical modelling based on back analysis of previous experiences of failure observed and measured in mining or civil excavations. The primary copper ore of El Teniente mine has no fractures; therefore, it is difficult to determine a rating that would enable to scale laboratory data, such as, RMR (Laubscher, 1977) or GSI (Hoek, 1994). This is the reason why the first option is not valid unless the entry data is manipulated or adjusted in order to obtain reasonable results. The second option requires, in general, a good characterization of a previous failure event in the rock mass, which is not always available. In recent years, new techniques of numerical modeling have been developed (PFC3D, ELFEN, Abaqus). Those methodologies are the third way to estimate the strength of the rock mass, but they are still in development. Particularly, the concept of SRM developed by Itasca is implemented in this study (Pierce, Mas Ivars, Cundall, & Potyondy, 2007; Mas Ivars et al., 2011), aiming to capture the real behaviour of the rock mass."

Jan 1, 2015

By John A. Davis, David W. Brunton

(Excerpts, pp 157-160) The usual means of firing blasting charges, especially in tunnels and adits in the Western States, is by the use of a safety fuse. The term safety fuse originated from the fact that when properly used under working conditions this fuse burns at a uniform rate and does not flash or explode, as was often the case with the means employed for igniting blasting charges previous to its invention; but the term is somewhat misleading, because the fuse is not, nor has it ever seriously been claimed to be, safe for use in gaseous coal mines. The fuse used for tunnel work is composed of a core of gunpowder surrounded by various layers of waterproofing material.

Jan 1, 2015

By Lon Santis, Bill Evans, John Tatom

Debris data from the Department of Defense Explosives Safety Board’s Project ESKIMORE full-scale explosives event test program are compared to quantity-distance (Q/D) standards and quantitative risk analysis (QRA) methods. The ESKIMORE test program involved quantities of explosives ranging from 1,000 to 60,000 pounds detonated in typically sized structures made of metal and concrete. Debris from these events was extensively surveyed and catalogued. The debris patterns from these events show varying degrees of directionality normal to the walls of the structures. These density patterns are overlaid an existing explosives storage site that is comparable to the test conditions. Analysis of the debris patterns in relation to Q/D standards shows that exposures located beyond the Q/D arc but along the normal to walls of potential explosion sites (PES) may have much higher debris density than exposures at the same distance on the corners of the same PES. Analysis of the debris patterns shows that predicted patterns using the QRA tool IMESAFR v2.0 closely match actual patterns. Additionally, IMESAFR based QRA methods are able to quantify the different risk levels of being exposed along the wall’s normal as compared to being exposed on the structure’s corner. Methods and decision making criteria to mitigate risk based on the directionality of PES debris are presented. Copyright ©

Jan 1, 2015

By Brian Wilson, Franz-Werner Gerressen

"Cutter Soil Mixing, also known as CSM, was developed in Europe as an alternate method of Deep Mixing to the more traditional single and multiple auger techniques, and brought to market by Bauer Maschinen GmbH (Bauer), towards the end of 2003. Initial development of the technique had been completed in a joint venture between Bauer and Bachy Soletanche. In 2004 the concept was introduced to the North American market. Continued development of the method and demonstration of its versatility, both in terms of applications and applicable soil types has seen a steady growth in the number of designs incorporating the approach, and contractors offering the technique. This paper provides a brief overview of the variety and size of projects and applications where the method has been adopted, discusses some lessons learned with respect to equipment operation as well as the improvements that have been introduced to the equipment, and briefly reviews the current state of practice, as well as some of the associated on-going research and development.BACKGROUNDCutter Soil Mixing (CSM) is a technique for deep soil mixing that was initially developed as a collaborative effort between Bauer Maschinen (Bauer) and Bachy Soletanche, but which ultimately resulted in the separate development of two somewhat different brands of CSM tool. The Bauer brand of CSM entered the European market in 2004, and was first promoted in the North American market in late 2004, with the first project starting in 2005. The Bachy Soletanche brand, sometimes referred to as “Geomix” was first marketed in Europe in 2005 and the first model introduced in North America in 2007.The development of the Cutter Soil Mixing technique utilized the experiences gained from Trench Cutter/Hydrofraise equipment, developing a technique that incorporates two cutting wheels rotating about a horizontal axis as opposed to the more conventional deep soil mixing approach which utilizes augers and mixing paddles rotating about vertical axes. Whereas the Trench Cutter/Hydrofraise technique excavates the soil from within a panel, and supports the open hole using a bentonite slurry, the CSM technique cuts and displaces the soil whilst pumping a slurry/grout directly into the soil through a port located between the wheels. The combination of cutting the soil while introducing an appropriate volume of slurry effectively fluidizes the column of soil around and above the cutter head. While this process achieves a high degree of mixing, even on the downward cutting stroke, thorough in-situ mixing typically occurs on the withdrawal stroke, when most of the slurry is added."

Jan 1, 2015

By J. H. van Laar, L. J. van der Walt, P. L. Crouse, H. Bissett, G. J. Puts

"SynopsisSilicon carbide nanopowders were produced using a microwave-induced plasma process operating at 15 kPa absolute and at atmospheric pressure. Methyltrichlorosilane (MTS) served as precursor, due to its advantageous stoichiometric silicon-to-carbon ratio of unity, allowing it to act as both carbon and silicon source. Argon served as carrier gas, and an additional hydrogen feed helped ensure a fully reducing reaction environment. The parameters under investigation were the H2:MTS molar ratio and the total enthalpy. The particle size distribution ranged from 20 nm upwards, as determined by SEM and TEM micrographs. It was found that an increase in enthalpy and a higher H2:MTS ratio resulted in smaller SiC particle sizes. The adhesion of particles was a common occurrence during the process, resulting in larger agglomerate sizes. SiC layers were deposited at 15 kPa with thicknesses ranging from 5.8 to 15 µm.IntroductionIt is well known that methyltrichlorosilane (CH3SiCl3 or MTS) decomposes to form silicon carbide (SiC) and hydrogen chloride (HCl) as shown in Equation [1]. The reaction kinetics and mechanisms for this reaction are thoroughly reported in the literature (Sone et al., 2000; Papasouliotis and Sotirchos, 1999; Kaneko et al., 2002; Wang et al., 2011)."

Jan 1, 2015

By B. Li

"The spontaneous combustion of coal storage pile(Gangue Hill) is one of the seriously threat encountered in coal mining and storage. The dynamic accumulation of internal heat in coal storage pile(Gangue Hill) provides continuous heat-source for coal spontaneous combustion. Combined with the features and characteristics of coal pile storage, a technology of heat pipe(HP) is applied to enhance heat transfer. In order to prevent spontaneous combustion of coal storage piles (hillock) due to regeneration, a method using heat pipes to destroy the heat preservation conditions of coal storage pile(Gangue Hill) is proposed, which reduces the risk of coal spontaneous combustion and prevents coal fire. A theoretical model of Coal-Thermosyphon has set up to analysis the radius of cooling effect area quantitatively. An experimental equipment of the heat transferring in a set of heat pipe, which used to study the influence on coal pile temperature distribution, has been designed. Results show, the heat pipe has a significant effect on inhibiting the coal spontaneous combustion process by destroy the heat preservation conditions of the coal. Under the experimental conditions, the most obvious coal temperature decline appears at radius 20.0mm around the pipe, dropped from 45.8? to 32.5?, a decline of 29%; the coal pile temperature at radius 420mm from 12.9? to 12.4?, a decline of 3.87%. And the research offers an effective and new approach in its application and promotion for preventing and controlling in coal spontaneous combustion.INTRODUCTION China is one of a few countries which utilize coal as the major source of energy in the world, and is the one whose characteristic of energy structure is rich coal, deficient oil and lean gas. Relatively speaking, China is abundance in mineral resources. The coal, which is the fundamental resource in the process of industrialization, is the main energy in china. Thus China cannot alter the situation of coal consumption dominated a leading role in its energy structure in near term.A massive of coal gangue would be produced every year in China with the mining activities. And it’s estimated that almost 360 million tons gangue were dumped in 2003, accounting for 10 percent of the whole coal production. Huge numbers of coal waste piles have more than 2,600 seats, which cover an area of over 12,000 hectares. Worse more, the coal gangue still has an annual growth rate of 100 million tons. Toxic smokes and greenhouse gases are discharged directly and prolongly into the atmosphere due to coal gangue spontaneous combustion. Even worse, waste dump explosion cause massive losses and are able to endanger the safety of workers. For example, one waste dump of the NO.4 Mine of Pingdingshan Coal Group Co., Ltd. occurred twice of explosions in 2005, and about 3.13 million tons of waste rocks were thrown within the range from 100 to 300 meters, eight people were killed and 122 rescuers and miners were burned, and economic losses were estimated more than 3,000 million."

Jan 1, 2015

By Y. Kashiwaya, J. Yagi, P. R. Austin

The problems of global environment and resources have become important issues in recent years, and the iron and steelmaking industry is requested to decrease energy consumption and carbon dioxide emission. The improvement of efficiency of ironmaking system is one of the countermeasures for these problems because more than a half of total energy input to the integrated steelwork is input to the ironmaking system. Various approaches to improve the blast furnace process have been made. The authors examined their performances through mathematical simulations of blast furnace operation, and confirmed the improvement of blast furnace efficiency under some operating conditions. The ironmaking system consists of various processes, and the materials and the energy are transported among these processes. Thus it is necessary to evaluate the efficiency of the novel operation of blast furnace based on the ironmaking system. In this study, the balances of material and energy on ironmaking system that consists of blast furnace, coke oven, sintering and hot stove processes were analyzed. The operation status of each process in the system was adjusted according to the results of the operation simulation of the blast furnace under novel operating conditions. The analysis clarified the effect of the blast furnace operation on the energy balance and CO2 emission of the ironmaking system.

Jan 1, 2015

By Elia Elias, Alan Crosky, Paul Hagan, Damon Vandermaat, Serkan Saydam, Peter H. Craig

"The University of New South Wales (UNSW Australia) had been involved in the study of premature failure of rock bolts in Australian coal mines from the initial identification of the problem in 1999 (Crosky et al 2002). Rock bolt steel changes over the last decade appear to have not reduced the incidence of failures. A broadened UNSW research project funded by the Australian Research Council (ARC) and Industry has targeted finding the environmental causes through extensive field and laboratory experiments. This paper describes the field studies conducted in underground coal mines, in particular attempts to measure the contribution to corrosion from groundwater, mineralogy and microbial activity. Various underground survey techniques were used to determine the extent of broken bolts, with the presence of both stress corrosion cracking (SCC) and localized deep pitting making no single technique suitable on their own. Groundwater found dripping from bolts across various coalfields in Australia were found to be not aggressive and known groundwater corrosivity classification systems did not correlate to where broken bolts were found. In-hole coupon bolts placed in roof strata containing claystone bands confirmed the clay as being a major contributor to corrosion. Microbes capable of contributing to steel corrosion were found to be present in groundwater, and culturing of the microbes taken from in-situ coupon bolts proved that the bacteria was present on the bolt surface. An ‘in-hole bolt corrosion coupon’ development by the project may have multiple benefits of 1) helping quantify newly developed corrosivity classification systems, 2) providing an in-situ ground support corrosion monitoring tool, and 3) for testing possible corrosion protection solutions.introductionThe problem of premature rock bolt failure in Australian coal mines was published in 2002 and 2004 by UNSW Australia from Australian Coal Association Research Program (ACARP) funded projects. The majority of the broken bolts examined had steel Charpy impact toughness values of 4 – 7 Joules, and the failure mechanism was most often stress corrosion cracking (SCC). Steel fracture mechanics predicts that an increase in impact toughness will increase the length of the crack before sudden brittle failure. In the final report of 2004, anecdotal evidence from one coal mine indicated that the problem may be eliminated in some environments by a change to steel grades with higher Charpy impact values of ~16. (Crosky et al, 2002 and 2004)"

Jan 1, 2015

By N. Erarslan, M. Ghamgosar

With the increased use of mechanized rock excavation, there have been developed internationally a number of methods to assess the abrasivity of rock materials. These methods range from determination of abrasive and hard mineral content using petrographic thin section analysis to weight loss or rate of wear flat development on specified test pieces. The Cerchar abrasivity index (CAI) test has been widely accepted for the assessment of rock abrasiveness and is determined as the abrasion of a steel pin after scratching over the freshly-broken or saw-cut surface of a rock. Two types of testing devices are in use today: (i) the original ‘Cerchar apparatus’, and (ii) the ‘West apparatus’, which was adopted herein. The CAI is calculated from the measured diameter of the resulting wear flat on the steel pin after 10mm scratching. This test has been considered to provide a reliable indication of rock abrasiveness for isotropic rocks. However, a great amount of rocks in natureis anisotropic. Phyllite is an anisotropic and foliated metamorphic rock and various types of phyllite specimens were tested in this research. Although phyllite is a type of rock primarily composed of quartz and the expected CAI value can be high, mechanical cutting of this rock should not be very problematic compared with igneous rocks have same CAI value. As phyllite is a foliated metamorphic rock, most of the specimens split into sheets through the quartz seam by the tip during scratching normal to the axis of quartz seams. Hence, viability assessment of Cerchar abrasivity test and F-Schimazek index values for the anisotropic rocks is investigated in this research.

Jan 1, 2015

By Alessandro Navarra, Roberto Parra, Boyd Davis, Frank Mucciardi

A smelter scheduling algorithm has been developed, which allocates the oxygen production between the smelting furnace and the converter aisle, so as to maximize copper throughput. The algorithm is intended for daily operation planning, controlling the sequencing of the converter cycles, and the oxygen drawn by these cycles. In some cases, it may be worthwhile to decrease converter oxygen allocation in favour of the smelting furnaces. Thus, a better utilization of the oxygen plant can increase primary copper throughput by several percentage points. This principle is demonstrated through sample computations. The approach presented in this paper can be incorporated into smelter management software.

Jan 1, 2015

By T. Billotte, G. Tirand, J. Zollinger, V. Robin, B. Rouat, D. Daloz

The grain structure prediction of metallic alloys during a welding process is often an issue. In addition to the welding parameters and the alloy nominal composition and properties, the base metal grain structure and chemical homogeneity also play an important role in the formation of the final microstructure. In this paper intensive characterisation of solidification structure in gas tungsten arc welding of Ni base alloy 600 are described. It is shown that in transverse section of the weld, while the grain structure shows some texture following constrained solidification growth, grain density in the weld is similar or greater than grain density in the heat affected zone. This suggests that simulation of the welding structure needs, in order to be predictive, to take into account : epitaxial growth, secondary nucleation events and 3D growth inside the weld pool.

Jan 1, 2015

By J. A. Maritz

"The Hedley and Grant formulation for pillar strength has been widely adopted by the South Africa hard rock mining industry. Today, some forty year later, this formula still provides the foundation for pillar strength calculations when designing for stability and utilising pillars in mine layouts. Various mine specific back analyses were conducted to adjust the equation parameters based on underground observations of failed pillars and comparing to the pillar stresses calculated using numerical models. In all these instances, the influence of shear stresses was ignored. The key to more representative pillar strength estimation is a better understanding of the pillar loading environment.In this paper, special mining cases are evaluated and the existence of shear stresses on the pillar loading environment is illustrated. By revisiting some back analysis data for optimisation of the equation parameters, recommendations were made in respect of the influence of the shear stress component and on how this should be considered in determining the pillar strength.INTRODUCTIONCommon practice on flat dipping, shallow and intermediate depth ore deposits in the South African hard rock and coal mining industry is to exploit the mineral resource using a room-and-pillar layout. The design methodology is mainly based on a Factor of Safety (FoS) approach, where the strength of the pillar is compared to the effective load on the pillar. In these environments, FoS values of 1.6 are applied as it was found to correspond to a probability of failure in coal mines of 0.001. As discussed by Ryder and Jager (2002) page 279: “For lack of anything else more substantial, the figure of 1.6 is generally used in hard rock pillar design in South Africa”. Dependant on the designed purpose of the pillar, the FoS might be selected as high as 2.0 where long term stability is required. The factors directly influencing the FoS include the pillar height (which is linked to the mining height), effective pillar width, a rock-strength factor and extraction ratio."

Jan 1, 2015

By K R. Brentley

"Tshepong Mine, Harmony’s largest gold producing mine, is situated in the Free State portion of the Witwatersrand Basin, east of Odendaalsrus and north of Welkom, South Africa. The Basal reef is a narrow tabular conglomerate and is the main gold bearing ore body. The strata strikes mainly in a northsouth direction with an average dip of 22 degrees. Currently mining takes place at depths of between 1 690m and 2 150m below surface. The Basal reef unit consists of a conglomerate ranging between a few and 30cm in thickness. Some 80-90% of the gold occurs in the lower portion of the conglomerate. Directly above the conglomerate is a quartzite placer unit, the Basal quartzite, which is a clean, hard competent rock and varies in thickness between 50cm and 200cm. The Basal unit is overlain by the Khaki shale which can vary between 30cm and 500cm in width. It is weak and incompetent khaki coloured chloritic shale.A method of stoping, termed “undercut”, is practiced in order to remove the lower 15-20cm of the gold rich strata. The method entails removing this portion along with some 70-80cm of footwall host rock which is a strong competent quartzite. The hard competent quartzite overlying the conglomerate is left in-situ to form a competent hangingwall which can stabilize and prevent exposure of the weak Khakishale. This method of extraction was developed through trial and error and has been used reasonably successfully since its inception in the early 1960’s where the method was developed to extract the Basal reef at the Western Holdings Mines. Recently prospect drilling and a number of localised hangingwall failures indicated that the residual quartzite beam could be less than 60cm and in some instances as thin as 30cm in certain areas of the mine. The result of this is a less stable hangingwall which not only poses a safety risk to workers in these areas but also had the potential of locking up some 840 000 Tonnes of gold bearing ore. At the present gold price this amounts to revenue of approximately ZAR1.5 billion (U.S. $143 million).This paper discusses the method of “undercut stoping” and existing practices in place at Tshepong Mine. It also explores new initiatives such as the use of a simple freely-supported elastic beam solution to perform back analysis, on-site data capturing of beam thickness and support geometries in order to develop empirical design charts and numerical modelling to assist in the verification of the empirical design method."

Jan 1, 2015

By J. H. Pee, Y. J. Kim, H. U. Lee, G. H. Kim

The general recycling process of tungsten scrap to produce tungsten raw materials (tungstic acid, ammonium paratungstate (APT) and WO3) have been carried out by the oxidation, milling, sodium-fusion, dissolution, and extraction processes. Many studies on the high temperature oxidation of tungsten scrap have investigated various aspects such as swelling kinetics, fracture resistance, and the effect of alloying composition. However, the accelerating factors on the scrap oxidation rate during oxidation were not considered here. In general, oxidized products were fused with sodium carbonate or sodium hydroxide to produce Na2WO4. Later in the process, solid Na2WO4 was dissolved in water. This process required considerable reaction time and was a costly process. Therefore, the aim of this study was to increase the solubility of solid oxidized products to produce Na2WO4 solution by hydrothermal reflux method. Na2WO4 solution was used to produce CaWO4 and H2WO4 by general chemical reactions with calcium chloride and hydrochloric acid. Ammonia solution was also added to the tungstic acid to produce APT. In this study, the effect of ammonia addition on the APT precipitation process was investigated in detail.

Jan 1, 2015

By J. P. Harrison, G. F. Gambino

"This paper examines unpredictability in the parameters governing hydraulic fracturing (HF) as used in stress amelioration for underground excavations, with the aim of showing how this unpredictability may affect design decisions. Using uncertainty models that are appropriate to particular levels of information and degrees of uncertainty, this paper demonstrates how these can aid in decision-making related to feasibility assessments of HF arrays for stress amelioration.Cave mining operations produce large underground voids and high stress concentrations around critical mine locations. These stress concentrations increase the potential for rock burst events. Although de-stress blasting has a long history for redistributing high stress concentrations, to improve safety and reliability HF is now being trialled as an alternative.Unfortunately the HF process is extremely uncertain, and so predicting fracture propagation geometry is difficult. Although the major parameters governing HF propagation have been previously identified, no indication has been given regarding the contribution that uncertainty in these makes to unpredictability in the overall HF system. Using simplified models of HF and referencing a recently proposed characterization of unpredictability, we relate unpredictability in the various governing parameters to the effect it has on strain energy density (SED) in the surrounding rock. Within these models we analyse SED as well as the stress intensity factor (KIc) when investigating the effect of parameter uncertainty and its influence on various crack propagation criteria (Sih & Macdonald, 1974). These models are applicable to unpredictability associated with the development of new fractures; the case of pre-existing fractures is the subject of on-going work.The paper will assess in greater detail the various governing parameters, and investigate the appropriate use of other uncertainty models. As a result, we will show how assessment of uncertainty in HF parameters can be used to both guide feasibility studies and determine the optimal allocation of resources to improve the final design."

Jan 1, 2015