Search Documents

By Ambarish Ghosh, Rituparna Dey, Indrajit Chowdhury

"In port and harbor facilities, jetties and cargo berth terminals are usually installed on piles that remain partially embedded in soil, while a part of it behaves as columns supporting top deck. Technology in vogue adapts a pseudo static analysis in computer where the top deck including piles are analyzed as an integrated system based on finite element method when the piles are modeled as beam elements, while the soil in which it is embedded is modeled as linear or nonlinear springs. Typical berthing force of the ship is considered as a pseudo static force where the dynamic characteristics of the force is taken into consideration by an equivalent impact factor and little study exists on the actual behavior of these type of piles under the transient shock due to berthing impact. Present paper proposes an analytical solution based on which one can compute the dynamic response of such jetty piles considering shear modulus of soil constant with depth. Considering the solution is analytical in nature no special software is needed and can well be adapted fordesign office practice using generic utility software like MATHCAD, MATLAB etc. that makes theproposed model computationally very efficient.INTRODUCTIONResponse of piles under dynamic load has been an important study in the realms of civil engineering, where significant research has been carried out on its dynamic behavior under harmonic loads like one experienced in a machine foundation or under seismic force.A number of researchers have given solution to this problem like Parmelee et al (1964), Tajimi (1966), Penzien (1970), Novak et al (1974, 1983), Banerjee and Sen (1987), Dobry and Gazetas (1988),Chowdhury and Dasgupta (2008).However, most of these theories are based on piles loaded under harmonic load and valid for long piles where structural failure precedes the soil failure considering the piles are long and flexible."

Jan 1, 2015

By Christopher J. Ramsey, Don W. Dotson

"An existing four lane section of US 27 was widened to eight lanes. The project lies in the rugged Valley and Ridge Province of the Appalachian mountains starting at the Tennessee River in Chattanooga, Tennessee and extending 2.6 km north to Signal Mountain Boulevard. This terrain presented many challenges to accommodate the road widening in the narrow, rugged topography. Multiple tiered wall systems consisting of large tieback walls, post-tensioned reaction blocks, and gravity MSE walls for a total of approximately 30 retaining walls were required. The retaining walls served to stabilize the thrust faulted geology while also minimizing right-of-way acquisitions. The cut walls consist mainly of a tiered system of tied-back soldier piles walls with cast-in-place concrete facing. Cast-in-place pile shear walls were required along the toe of existing MSE walls to maintain stability during construction. This paper discusses the design methodology, which includes a hybrid (rather than traditional) earth pressure diagram intended to reduce life-cycle maintenance and long-term performance. Further this paper addresses wall construction, slope stability analysis, landslide mitigation alternatives, soldier pile wall design features, site challenges, monitoring and performance (to date) of the wall systems.INTRODUCTIONThis project involves the proposed widening of US Highway 27 (State Route 29) from the north end of the Tennessee River Bridge at Manufacturer’s Road to State Route 8 (Signal Mountain Road), approximately 2.64 km of roadway (Fig. 1). The project site is located adjacent to the Tennessee River on the north side of downtown Chattanooga, Tennessee in Hamilton County. The existing, limited access highway is to be widened from four lanes (two northbound and two southbound) to a minimum of eight lanes. Some portions of the alignment will expand to as much as ten lanes where northbound and southbound ramp acceleration/deceleration lanes coincide.In addition to the number and heights of cuts and fills involved, a major factor in determining an economical design for the alignment is the complicated geologic conditions along the roadway alignment. The existing roadway is situated between several steep cut slopes, some of which are only marginally stable or currently exhibit signs of instability. Due to the proximity of the project to the downtown area, the steep slopes along the alignment, and the relatively dense population near the alignment, widening the pavement and constructing cut and fill slopes to a stable configuration would result in major land acquisition for slope right-of-way."

Jan 1, 2015

By Madan Kumar Annam, Hari Krishna Y, I. V. Anirudhan

"For completion of projects in time with positive results, improvements of productivity and effective project management procedures have become extremely important. This paper discusses a milestone project comprising 198 residential units of stilt plus 4 levels that highlighted the benefits of these key aspects. Success of ground modification procedure benefitting the entire cycle involving End Users, Suppliers, Bankers and Developer is discussed.Soil profile for a considerable depth comprises weak layers of silty clay and sandy clay with varying consistency. Deep foundations have been an automatic choice of foundation for major buildings constructed in similar environment. After serious geotechnical appraisal, reconsideration of the foundation system with an alternative solution of Ground Improvement was found to be optimal in terms of Cost and Time. Full raft foundation on the improved ground by installation of Vibro Stone Columns (dry bottom feed method) was considered as an alternative foundation system. The ground improvement works were completed within 6 weeks (as against 6 months to that of pile foundations) that was made possible through effective project management. Full size plate load tests were conducted to ascertain effectiveness of the ground improvement works. Success of the foundation system was proved by full scale monitoring of foundation settlement during and after completion of the project over a span of 2 years. This paper describes design considerations, quality control in the construction of Vibro Stone Columns (dry bottom feed method) and performance monitoring of the project thereafter.INTRODUCTIONGenerally in weak deposits, deep foundations like bored cast-in-situ piles and driven piles have historically been the foundation choice for major buildings and other structures. Construction of pile foundations is becoming a challenge due to their high cost, large construction time and due to severe environmental issues (noise pollution, ground vibrations and carbon footprint). Since the proposed building complex is located within the proximity of a well-developed residential locality, objections raised by neighborhoods to pile driving activities called for a rethinking on the foundation system.The top 6m to 8m of soil profile comprises of silty clay / sandy clay having highly varying consistency. GWT was encountered at 3.0m below the existing ground level. Under this situation, the reconsideration of the type of foundation system with respect to the geotechnical analysis gave a thought to assess feasibility of ground improvement system."

Jan 1, 2015

By Adnan A. Malik, Tadashi Maejima, Jiro Kuwano

"The use of steel screw piles has greatly increased in recent years because of the advancement in the installation mechanism and its performance under compressive, uplift and lateral loads. In a steel pile system, the strength of pile material limits the end bearing resistance of the pile due to strong subsurface conditions. The installation mechanism of screw pile can reduce the end bearing resistance due to the torque and axial force. However, if the installation mechanism does not reduce the bearing resistance of the pile, another important factor that can reduce its performance is the strength of the helix/wing plate. In this study, the effect of wing plate deformation on the performance of single helix/wing plate pile bearing resistance investigated. A model ground was used to investigate the effect of wing plate deformation. Dry Toyoura sand was used as a ground material and was compacted to denser states of 80% and 92%. The shaft and wing plate material of the pile was the same to actual piles that are used nowadays in Japan. A series of load tests were performed with different wing plate diameters and thicknesses. It was observed that deflection in the wing plate reduces the bearing resistance of the pile. The increase in the thickness of the wing plate was seen to restore the reduced pile resistance due to deflection. It was also observed from the experimental results that the ratio of wing plate diameter to shaft diameter (Dw/Ds) greatly affects the deformation of wing plates, which ultimately affects the end bearing resistance of the pile. The results obtained in this research suggest that the outstand length (Lw) of wing plate should be less than 5.6 times the thickness of wing plate for piles having a large Dw/Ds ratio under strong ground conditions.INTRODUCTIONThe first use of screw pile was almost 180 years ago by Alexander Mitchell. He patented his invention in 1833 with the name “Screw Pile”, and used it for ship moorings. The use of screw piles has since been adopted in various areas such as lighthouses, fencing for agriculture and marine structures. The use of screw piles in civil works started in 1985, after the invention of the hydraulic torque motor, as it eases the installation process. Nowadays, screw piles are used in the foundation of transmission towers, elevators, buildings and many other civil structures.Screw pile has an edge over other steel pile systems due to its high bearing, uplift and lateral resistance. The end bearing resistance of screw pile depends on installation, strength of subsurface material and the pile material. The screw pile is installed by applying torque and axial force. The pile torsional strength should be more than the applied torque and axial force to avoid deformation before reaching the final depth."

Jan 1, 2015

By Amr Sallam, David Thompson, Moataz Hassan

"The Little Lake Harris (LLH) Bridge was constructed in 1951 to replace the eastwest County Road 48 Bridge connecting the towns of Howey-in-the-Hills and Astatula in Lake County, Florida, United States. The 78-span bridge carries two lanes of traffic, is 3,130 feet long, and 36.1 feet wide. The concrete deck is supported by steel I-girders carried by one row of 18-inch square precast concrete driven pile. In the late 1980's, slight settlements were observed in several bents. In 1990, Florida Department of Transportation (FDOT) initiated annual survey of deck elevations during bridge inspections to monitor settlement. Due to the slow nature and magnitude of settlement, substructure instability was not a major concern to the department. However, public concern over the settlement and rough ride of the bridge continued to rise. FDOT contracted Kisinger Campo & Associates Corp. (KCA) to provide the needed design to correct the dips in the riding surface and minimize future settlement. KCA's initial design was based on the concept of ""helper bents"" at the settled bents in order to restore the bridge to original elevation. Estimated construction cost for seven helper bents was about $3.3M. FDOT requested evaluating other alternatives to reduce the cost of the bridge restoration. KCA involved the geotechnical consultant, Terracon Consultants, Inc. (Terracon), to perform a peer review and provide an economical alternative solution. Jacking and shimming the bridge was determined to be both technically viable and economical with a total cost of less than $300K. The design was completed in March 2010 and construction was completed in February 2011. This paper provides an overview of the LLH Bridge history, summarizes the evolution of the design methodology including the findings of the geotechnical study and presents lessons learned during the design and construction of the project.INTRODUCTIONThe Safety and Preservation of the State Highway System is the top priority of the FDOT. Therefore, FDOT initiated a bridge management program that starts with conducting biennial safety inspections performed by Certified Bridge Inspectors (CBI). The inspection reports together with the CBI’s recommendations are reviewed by a registered Professional Engineer (PE) and work orders are issued with priority ranking depending on the severity of the bridge deficiencies. If the scope of work is considered beyond the in-house crews’ capability, the work is then included in a contract for and bid. LLH Bridge was a little different. It was initiated in direct response to number of complaints the FDOT District 5 Structures Maintenance Office (D5SMO) received regarding settlement of the Little Lake Harris Bridge."

Jan 1, 2015

By Scott D. Neely, Donald R. Clark

"An existing landslide located at the southeast corner of the Telluride Regional Airport has been in an active state of failure for several years. The presence of the landslide has represented an on-going liability for the Airport, the Federal Aviation Administration and the Colorado Department of Transportation. A catastrophic failure of this landslide occurring in a manner similar to that which occurred at the Airport in 1987 has posed an on-going threat to closing Colorado State Highway 145 south and below the slide area. The existing landslide has been characterized as a series of multiple failed block areas located downhill of the airport runway that have occurred in severely weathered Mancos Shale.A total of 12 alternatives were evaluated to mitigate the landslide, including the preferred alternatives of either partial or total landslide removal. However, prior development has left essentially no place on the airport property that would allow for the disposal of the landslide debris for either the total or partial removal alternatives, and the closest off-site disposal area was approximately 40 miles from the site. As a result, in-situ stabilization of the landslide, including a primary system of isolated tie-back anchor plates with strand anchors, and a secondary system of high strength steel mesh and intermediate anchors was selected for the ultimate design of the project to stabilize the landslide in place.For design purposes, geotechnical characterization of the slide area was accomplished through geological mapping, conventional borehole exploration and geophysics using multiple electrical resistivity. The paper discusses the design process utilized and the unique challenges faced one-third of the way through construction when discovery of a survey error required redesign of the entire landslide mass stabilization system using the prefabricated anchors that had already been delivered to the project.INTRODUCTIONTelluride Colorado is located at the toe of the Colorado Rocky Mountains on the western slope. The Telluride Regional Airport is located on Deep Creek Mesa about 5 miles west of the town of Telluride.The landslide is located at the southeast corner of the airport just below an abandoned portion of the quarry access road on a south facing slope. The quarry access road is located below the elevation of the runway and outside the elk fence that surrounds the air traffic area of the airport property. Since the reconstruction of the runway, the access road to the quarry and the construction access road for the reconstruction of the airport runway and safety area were rerouted to stable ground north of the previous access road location and off of the head scarp of the landslide."

Jan 1, 2015

By Jacob A. Jordan, Rachel M. Garrett, W. Robert Thompson III, James C. Pegues

"Environmental control structures for an existing fossil-fuel power generating plant near Pascagoula, Mississippi faced several design and construction challenges due to space limitations. Conceptual design calculations indicated drilled shaft foundations would likely be needed to accommodate the higher lateral and compressive loads expected under some structures. A maximum drilled shaft diameter of 60-in was preferred due to various space constraints. Smaller diameter drilled shafts were deemed acceptable under structures with more moderate loading conditions. Furthermore, augercast piles were considered where lateral loading was not a governing design criterion.A series of SPT borings and CPT soundings revealed a subsurface profile consisting of soft to firm clays to depths of about 25 feet, underlain by fine to coarse sands. The apparent relative density of the sands was loose just below the clay, with increasing density noted with an increase in depth.Analysis of conventional drilled shafts indicated needed capacities could not be achieved unless shaft lengths exceeded 100 feet. Post-grouted drilled shafts were therefore evaluated to decrease shaft lengths by taking advantage of increased base capacity. Analyses showed the higher predicted capacities needed for some structures could be achieved with this approach. Final design for the project incorporated 90-ft long, 60-in diameter post-grouted drilled shafts; 60-ft long, 48-in diameter post-grouted drilled shafts; and 60-ft long, 48-in diameter conventional shafts. Both post-grouted and conventional trial shafts were installed as part of the detailed design phase of the project. Each trial shaft included CSL integrity testing and Osterberg-cell bi-directional load testing. Load test results revealed that additional base capacity was, in fact, achieved through the post grouting process. The 60-in diameter post-grouted production shafts and the 48-in diameter conventional production shafts have been installed at the site, with the project that would utilize the 48-in diameter post-grouted shafts deferred at this time."

Jan 1, 2015

By Pancho J. Garza, Keith H. Dahlen, Chris A. Labye

"Design for reconstruction of the East Flagstaff traffic interchange project located in Flagstaff, Arizona posed particular challenges. The proposed design included construction of a nearly 50-foot tall mechanically stabilized earth (MSE) wall given rightof- way constraints and soft subgrade soils. The tight right-of-way, approximately 15 feet in certain locations, adjacent to existing structures limited the number of viable remedial alternatives to provide grade separation at the proposed bridge abutment without significant settlement. Preliminary analyses indicated the existing subgrade soils - consisting primarily of relatively soft silts and clays with decomposed pumice - would settle approximately 12 to 14 inches resulting in unacceptable wall deformation. Stone columns placed via vibratory methods (vibro-replacement) consisting of circular excavations which penetrate to firm bearing soils and which are filled with crushed stone were selected to densify the existing subgrade soils. The implemented mitigation measures helped limit settlement to less than one inch and allow for successful construction of the project. The project history - including site constraints, subsurface conditions, evaluation of remedial alternatives, stone columns methodology, and effectiveness of ground improvements - will be discussed.IntroductionThis paper describes the subsurface investigation performed for the reconstruction of the Business Route 40 (B-40) (Country Club Drive) and United States (US) 89 Traffic Interchange (TI) located within the city limits of Flagstaff, Arizona. This project is currently referred to as the East Flagstaff TI. The Project Site Vicinity Map is shown below.The former B-40/US 89 TI was considered ineffective in handling the current and projected volumes of traffic which transition from northbound (NB) B-40 to US 89 (both directions), as well as from southbound (SB) US 89 to SB B-40. The intent of the project was to reconstruct the TI to better accommodate projected traffic volumes. The project eliminated the existing ramps from both NB B-40 to SB and NB US 89. The new interchange includes a Tee intersection from B-40 to US 89. In order to accommodate this alignment, the profile of US 89 was raised several feet (on nearly the same as existing horizontal alignment) to match the elevated profile of B-40. B-40 was shifted just west of its current alignment to accommodate construction of a new, wider bridge structure which spans over Industrial Drive, the Burlington Northern Santa Fe (BNSF) railway, and old Route 66. South of the new bridge, B-40 transitioned back to the existing alignment just north of the I-40/B-40 TI. Within the project limits, both US 89 and B-40 were widened to three travel lanes in each direction."

Jan 1, 2015

By Robert C. Simpson, Ghada S. Ellithy

"There are several methods for estimating the axial capacity of drilled shafts installed in coarse-grained soils. Most methods estimate the ultimate capacity for side friction and tip resistance. Design capacity is then calculated by applying a resistance factor to the ultimate capacity. In reality, however, ultimate resistance may not be mobilized except after a significant displacement that is not structurally tolerated in either compression or tension modes.A full- scale load test is the best way to obtain the load settlement curve for a drilled shaft, especially in soil formations where accurate estimation of soil frictional properties from a field investigation may be difficult. This paper presents the results of a static, axial, compressive bi-directional load test, using the Osterberg method (O-cell test). The test was designed so that the shaft above the O-cell would move up and the shaft below it would move down when loaded. At the start of the test the concrete around the O-cell is fractured generally on a plane near the bottom of the cell.The test was designed to validate the design capacity of drilled shafts embedded into the Vashon recessional outwash (Qvro), which is a glacially derived sediment consisting of thick deposits of cobbly sand and gravel relatively free of silt and clay found in the Seattle, WA area. The test shaft consisted of a 2.5- feet (0.75 m) diameter drilled shaft. The test shaft was installed to a depth of about 47 feet (14.3 m) into this formation. A maximum load of 437 kips (1.95 MN) was applied during the test, in each direction. The maximum load was attained at upward and downward displacements of less than 0.1 inch (2.5 mm), respectively.Although the load test did not yield ultimate values, the results are compared to the design assumptions using methods adopted in the FHWA and AASHTO guidelines, which verified the adequacy of the design assumptions. We conclude that more emphasis is needed in the prediction of the service loads and corresponding mobilized displacement that may lead to a more cost effective design. It is also clear that more testing to higher loads could lead to more efficient designs on specific projects and generally as data is added to the local knowledge base."

Jan 1, 2015

By William M. Tanner, Daniel C. Brahana

"A drilled pier foundation was originally designed to support the proposed G. Wayne Clough Undergraduate Learning Commons on the campus of Georgia Tech in Atlanta, GA. Reflective of the site geology, the original drilled pier foundation was divided into a Northern and Southern portion with an allowable end bearing capacity of 60 ksf and 100 ksf, respectively. After initial pricing on the original design, several value engineering options were submitted that featured changes to the original design capacity and construction method. The project team selected the value engineering option that involved conducting an Osterberg Load Cell test to assess end bearing of the site bedrock and skin friction. Results of the Osterberg Load Cell test justified increasing the allowable end bearing capacity of the site bedrock to 100 ksf in the Northern portion and 125 ksf in the Southern portion. Considering the final foundation design and Osterberg Load Cell test program, a net savings of approximately $259,000, or approximately 34%, was obtained over the original design.Project BackgroundThe G. Wayne Clough Undergraduate Learning Commons (CULC) is a 5-story academic building on the Georgia Tech campus in Atlanta, Georgia. The CULC was completed in 2011 and consists of a concrete frame structure supported on a drilled pier foundation.After pricing of the original drilled pier foundation design, several value engineering (VE) analyses were performed by the foundation contractor in an effort to demonstrate the potential for a reduced foundation cost. The VE analyses focused on variations in design assumptions, as well as construction techniques. This paper presents a case study that demonstrates how the value engineering process can be used to reduce foundation costs.Site Investigation and Subsurface ConditionsThe CULC building site is located within the Southern Piedmont Physiographic Province, an area underlain by metamorphic and igneous rocks. McConnell and Abrams (1984) indicate that the site is located at the boundary between two distinct geologic formations. The Northern portion of the site is underlain by the Wahoo Creek Formation while the Southern portion of the site is underlain by the Stonewall Formation. The following paragraphs briefly describe the geotechnical investigations performed by the project geotechnical engineer (GE) for the CULC."

Jan 1, 2015

By Paolo Cavalcoli, Federico Pagliacci

"As opposed to the static functional recovery of existing structures, the construction of infrastructures in an urban environment, when combined with complex geological situations, often involves building foundation structures, whether circular or rectangular in section, through rock formations or chaotic strata (sand and gravel with cobbles). Until a few years ago, these formations or strata were sometimes an insurmountable constraint on traditional foundation installation techniques. The difficulty in overcoming these geological situations is sometimes added to the increasingly frequent need to reach depths that were unimaginable just a decade ago. These are real challenges for those carrying out these works and for those manufacturing the necessary equipment. There are two main methodological approaches to these problems, that can be summed up in the rhetorical figure of ""David and Goliath"": cunning versus force. In reference to the case studies in this article: the permanent retaining walls for the Copenhagen Metro, and the structural repairs to the Arapuni Dam in New Zealand and the Wolf Creek Dam in the U.S., we will describe the foundations constructed in presence of rock using combined small-diameter direction drilling solutions, associated with their enlargement up to the project’s size, at depths exceeding 300 feet. Finally, a case study will be presented on the implementation of a large cross-section of an excavation in the rock, at depths greater than 800 feet.IntroductionAs opposed to the functional recovery of existing structures, the construction of infrastructures in an urban environment, when combined with complex geological situations, often involves building foundation structures, whether circular or rectangular in section, through rock formations or chaotic strata (sand and gravel with cobbles).Until a few years ago, these formations or strata were sometimes an insurmountable constraint on traditional foundation installation techniques. The difficulty in overcoming these geological situations is sometimes added to the increasingly frequent need to reach depths that were unimaginable just a decade ago.These are real challenges for those building these works and for those manufacturing the necessary equipment. There are two main methodological approaches to these problems, that can be summed up in the biblical figures of ""David and Goliath"": cunning versus force. In the engineering field, the force is summarized in the use of ever-larger drilling equipment in terms of installed power, weight in working conditions, winch and rotary capacity."

Jan 1, 2015

By Fabio Santillan, Lyndon Bedford

"This paper presents the main features of the Wolf Creek Dam Foundation Remediation Project, highlighting the innovative construction approach and stressing on how the collaboration between the contractor and the owner became a key element for the success of this project.The main rehabilitation contract, $341 M, was awarded in 2008 for the construction of a 980,000 sqft concrete barrier. Most of this 2ft-wide concrete barrier wall is being built to depths reaching 277 ft using innovative construction techniques proposed by the contractor and under quality control measures that exceed by far the industry standards.The construction of the barrier wall entails the use of nine different foundation techniques which run concurrently following very stringent requirements in terms of verticality, distance between open elements, strength, permeability and dimensions that control the installation sequence of each barrier wall element.The innovative construction approach by the contractor and the collaborative efforts by the contractor and the USACE (“US Army Corps of Engineers”) have brought this unique and very difficult project to a successful completion, setting new standards in the dam foundation industry and nine months ahead of scheduleINTRODUCTIONWolf Creek Dam is on the Cumberland River in south central Kentucky. It provides hydropower, flood control, water supply, and water quality benefits for the Cumberland River system and surrounding region. The lake is a source of recreation that has attracted more visitors (4.89 million) than Yellowstone National Park (2.87 million).The dam and its adjacent reservoir reside upon a heavily Karst bedrock foundation. In late January 2007, the USACE placed the dam under a 'high risk' for failure designation. As a temporary measure, the pool elevation was lowered to 680 ft Above Main Sea Level (“AMSL”), 80 ft below its maximum capacity, with huge impacts to the local economy while the major, and ambitious, $ 594 million remediation program to bring the dam back to its full operating condition was carried out.The main rehabilitation contract of $341 million was awarded in 2008 for the construction of a 980,000 sqft concrete cut-off barrier. Most of this 2ft-wide concrete barrier wall has been built to depths reaching 277 ft using innovative construction techniques under quality control measures that far exceed the industry standards."

Jan 1, 2015

By Kevin Cunningham

"Litigation resulting from neighboring structures with settlement and/or lateral movement or improper pile design and faulty soils engineering analysis, are a multi-faceted opportunity for law firms. These types of claim scenarios are an attorney’s dream, and can obliterate a Deep Foundation Contractors profit and more importantly, can be avoided with a progressive approach to risk management in design and project management.The following (4) case studies will be examined and dissected to discern certain lessons learned for risk management solutions to avoid these deep foundation related challenges in the future.1) Pipe Flotation – Soil Conditions Not Anticipated in Specifications or Contract2) Easement Encroachment – Easement Dimensions Not Recognized Until Completion of Project3) Subjacent Lateral Support – Neighboring Structure Wooden Pile Unprotected Causing Structure to Settle4) Improper Pile Placement - Construction & Design Caused Retail Store to SettleSpecific Deep Foundation project challenges involving: buoyancy calculations regarding subsurface soil characteristics, design factors taking existing subsurface sewer line easements into account, structural instability as result of excavation causing exposure/heavy rainfall to existing wooden piles supporting adjoining building and improper pile location resulting from faulty pile design will be described with risk management recommendations to avoid these challenges in the future.From the very start of construction on any project deep foundation and excavating work poses numerous engineering and technical challenges for developers, contractors and engineers. Dealing with changing or hidden conditions is one of the most difficult challenges facing any contractor or engineer on a project. Relying on incomplete or inaccurate engineering reports is another common problem. Other challenges include dealing with technical errors or oversights that are deeply embedded in the project specifications or bid process.No matter what is the origin of the problem or how it manifests, deep foundation contractors, design professionals and engineers should be ever-mindful of good risk management practices that can prevent serious disputes that can result in costly litigation."

Jan 1, 2015

By Bernard B. Vannoy, Howard W. Gault, Ramesh Bobba

"Treviicos-Soletanche Joint Venture (JV) and the US Army Corps of Engineers (USACE) have installed a 3800-foot long, 275-foot deep and minimum 2-foot wide secant pile barrier wall at Wolf Creek Dam in Jamestown, KY. This paper describes the methodology employed by the JV and USACE to evaluate the overlap, thickness, and position of the barrier wall. It addresses the contractual requirements, positional uncertainty, and evaluation procedures.These procedures evolved over the course of the project as various issues were identified and procedures developed to evaluate these issues. During the project, it became clear that the JV and USACE could ascertain that the wall thickness and overlap requirements could be met if the overlap based upon Koden data was at least 0.7’ in the left-right direction. For a small number of piles with overlaps between 0.5’ and 0.7’, the piles are contractually compliant yet contain a minor degree of uncertainty in the overlap. Initially, the USACE assumption was that the amount of uncertainty of verticality measurements would require more than a 1-foot measured overlap in the left-right direction to confirm an actual, contractual 6-inch overlap. With time and experience, the limit of measured overlap was reduced in accordance with greater understanding of the equipment capabilities and tolerances. Other lessons learned include the need for Quality Control/Assurance personnel to collect data at the same starting point for every pile.For every pile the JV and USACE compared analog and digital data to provide confidence that the correct digital data was used for overlap calculations. Perhaps the most important lesson learned was the importance of the JV and USACE working together and sharing all data. Overlap analysis was performed by the JV’s Barrier Wall Specialist and a small number of USACE personnel. This resulted in a high level of experience and expertise within a small group.IntroductionThe Treviicos-Soletanche Joint Venture (JV) and the US Army Corps of Engineers (USACE) have installed a 3800-foot long, 275-foot deep, and minimum 2-foot wide secant pile barrier wall at Wolf Creek Dam in Jamestown, KY. The wall was installed through a 6-foot wide Protective Concrete Embankment Wall (PCEW) which was installed two feet into rock. The PCEW protects the embankment from erosion of drilling fluids during subsequent operations. Below the PCEW the piles were installed to a specified elevation (staggered at 475’ and 473’ below the 748.2’ work platform). The Ordovician limestone and shale bedrock is flat lying with few vertical fractures. These conditions facilitate the advancement of pilot holes with very low deviations (with considerable credit to the JV’s drillers and steering engineers). The pilot holes were spaced on 31.5-inch and 35-inch spacing. Subsequent enlargement of the pilot holes to 50’ resulted in a continuous wall. This paper addresses the requirements and procedures to assure that the wall was as wide, deep and continuous as specified."

Jan 1, 2015

By Ross T. McGillivray, David S. Graham, Dan A. Brown, Steven D. Dapp

"The Selmon Expressway includes an elevated structure extending across several miles of weathered karstic limestone geology, and represents a challenge for design because of the high variability of the material and the difficulty in characterizing the strength. The nature of the epikarst in this region of Tampa is such that variability can be extreme within distances of only a few feet. The weathered rock includes extremely soft soil infill within solution features on and within the formation. The limestone is so weathered that coring typically does not yield useful samples for strength testing, and in-situ Standard Penetration Testing (SPT) tests often encounter refusal blow counts. Thus the challenge for foundation design includes two components of reliability risks: the uncertainty associated with the ground conditions at a given foundation location plus the uncertainty associated with the foundation performance at a given location even when the stratigraphy is determined.This paper describes the design approach that has been implemented successfully for two projects at the Lee Roy Selmon Crosstown Expressway (LRS) in Tampa, Florida: the assessment and remediation of the reversible elevated lane (REL) foundations constructed in 2004, and the elevated expressways widening project constructed in 2012. Included in this design approach is a method developed for computing axial resistance in this local geology. Design for axial loading relies primarily on the development of side resistance, which was considered less subject to performance risks than base resistance. The calculation method incorporates a statistical analysis of SPT data, tempered by engineering judgment, to characterize stratigraphy at a given location into either soil, intermediate geomaterial (IGM) or rock.IntroductionThe subsurface stratigraphy of sites underlain by weathered limestone formations can be highly variable with respect to material layer thicknesses and strengths, even over short horizontal distances. This is the case for much of Florida, and particularly the Tampa area. These conditions present a challenging environment for the design of drilled foundations because of the need for a reliable determination of subsurface conditions at each foundation location, as they relate to the expected axial performance. Contributing factors include:"

Jan 1, 2015

By Ambarish Ghosh, Chitralekha Ghatak, Tanumaya Mitra, Tarun Sengupta, Sajib Das, Sankar Kumar Nath

"Currently construction of important structures like bridges, flyovers and high rise buildings in and around Kolkata are in full swing. These structures have mostly pile or well foundations. The design methodology and construction techniques are being employed keeping in view both the safety and economy of the project. The data presented in this investigation have been taken from Geotechnical Investigation report of Component B in connection with construction of Extradosed Cable Stayed Bridge over River Hooghly in Hooghly and Nadia district of West Bengal, India. The investigation site is located within close proximity of Eocene Hinge Zone which is being taken as the principal contributor of Earthquakes in and around Kolkata. Considering the importance of the project detailed and exhaustive geotechnical investigation has been carried out and site specific response spectra have been generated for analysis and design of the bridge. This paper presents site specific response spectra, liquefaction analysis and comparison of lateral load carrying capacity of pile using Winkler approach and IS 2911 guidelines.INTRODUCTIONPile foundations are used to transfer the load of the super structure through soft soil deposit to deeper bearing stratum by means of skin friction or end bearing or both. Pile foundations are regarded as a safe alternative for supporting structures in seismic areas and have been used for this purpose in non-liquefying as well as liquefying soils. But their design in case of potentially liquefiable soil is quite different from that of non liquefiable soil. In liquefiable soil the progressive buildup of excess pore water pressure will cause stiffness degradation and loss of strength which in turn will induce additional shear force and bending moment in the pile. The mechanism of pile behavior in liquefying soil has been investigated by several investigators in the recent years based on observations of pile performance during earthquakes and studies in the centrifuge and Shake Table tests. Exhaustive geotechnical investigation has been carried out along the proposed alignment of the Extradosed Cable Stayed Bridge i.e., along Baropara, Bansberia ROB, Ishwar Gupta Bridge, Saraswati River to collect disturbed as well as undisturbed soil sample, to develop average soil profile and to determine the design parameters. The proposed project site is very close to Eocene Hinge Zone, which is basically a strike slip fault, capable of generating an earthquake of Mw 6.7. Thus it is evident that the proposed Bridge needs to be designed considering the adverse geo-hydrological condition as well as the earthquake aspects needing special attention following the state-of-the-art technology as guided by relevant codes and published literatures. Considering the soil profile of these locations ground response analysis has been carried out using equivalent linear method to determine the site amplification. Site specific response spectra have been developed for the four zones and zone factors have been determined. The computed zone factors are 0.198g, 0.195g, 0.195g and 0.20g for the four zones respectively, much higher than the zone factor 0.16g, which is for zone III, as stipulated in IS 1893:2002."

Jan 1, 2015

By Kessi E. Zicko, Eric A. Hackenberg, Paul J. Lewis

"Following snow melt and spring rains in 2011, a landslide measuring approximately 600 feet long and 300 feet in slope length occurred within the southbound roadway embankment of a heavily travelled 2-lane divided highway in North Central Pennsylvania. Driven steel piles were designed to stabilize the embankment slope. Factors affecting the selected stabilization technique included an adjacent reservoir, wetlands, the length and depth of the failure plane, extent of glacial lake deposits, excess pore pressures in the foundation soils, and an area of archaeological interest. Field reconnaissance and subsurface explorations including borings, instrumentation, geophysics, and laboratory testing indicated that glacial lake deposits were present in the toe region of the embankment. Instrumentation proved key in measuring excess pore pressures and in locating the failure plane, and geophysics was utilized to estimate the extent of the soft glacial lake deposits and to estimate pile lengths. The existing condition of the embankment was modeled in computer slope stability analyses, which were also used to help assign soil parameters. Significant costs were associated with constructing a berm due to the impacts on adjacent site features. Therefore, multiple rows of driven steel H-piles were designed for installation along the toe of the embankment. The design lateral load in the piles was based on slope stability analyses, and the pile size and number of piles were based on lateral pile computations with modified p-y curves to account for installing piles in an active landslide. The relationship between the factors of safety from slope stability and the LRFD pile design was significant in determining pile loads for lateral analyses.INTRODUCTIONA landslide developed along the lower portion of the southbound embankment of State Route 15 in Tioga County, Pennsylvania. The road passes through a steep valley and is located along the southern extent of the Tioga Reservoir. Although no damage to S.R. 15 was attributed to this landslide, the close proximity of the slide to the road posed a concern for the long-term stability of this section of roadway.This paper presents a summary of the site history; the subsurface conditions based on borings, instrumentation, a geophysical survey, and laboratory testing; slope stability analyses including alternatives assessment; and the pile design.SITE HISTORYS.R. 15 was originally located in the valley along the Tioga River and traversed through the towns of Tioga and Mansfield. Although the reason is unknown, it is interesting to note that Old S.R. 15 curved away from the river in the area of the landslide. In the mid 1970’s, S.R. 15 was relocated to the eastern hillside prior to construction of the Tioga-Hammond Reservoir by the U.S. Army Corps of Engineers. The relocated highway was constructed in stages. Two lanes of relocated S.R. 15 were initially constructed to carry one lane of northbound and one lane of southbound traffic. At this same time, the majority of the fill was placed for two future lanes immediately to the west, which would eventually allow for two lanes in each direction. The two eastern lanes would then carry northbound traffic after completion of the two southbound lanes to the west."

Jan 1, 2015

By William G. Ryan, David S. Graham, Dan A. Brown, Rich A. Lamb, Paul J. Axtell

"The St. Croix River Crossing project on the Minnesota-Wisconsin border has been in the process of planning and public debate for two decades, with several changes in alignment. During the course of the earlier planning process in 1995, a drilled shaft load test was performed to obtain preliminary design information. There were some difficulties in maintaining stability within the weak sandstone bearing formation, and the measured axial resistance was relatively low. Subsequent experience by the Minnesota Department of Transportation with similar weak sandstones on the I-35W project suggests that improved construction techniques using modern drilling fluids may offer opportunities for improved performance. During final design in 2012 a second load test program was performed of a full scale test shaft constructed using polymer drilling fluids. The stability of the socket excavation in the weak sandstone appeared to be greatly improved and the measured axial resistance significantly higher.This case history illustrates the excellent performance that drilled shafts can provide in even relatively weak sandstone bedrock as well as the profound influence on axial resistance associated with the construction techniques used. The improved resistance values obtained by the new load test with more recent construction technology allowed the foundation scheme to be substantially optimized with respect to the number and size of required drilled shafts, reducing the size, cost, and risk of the coffercells and footings.IntroductionThe Minnesota Department of Transportation (MnDOT) has awarded the first phase of a bridge construction project that will cross the St. Croix River between Oak Park Heights, MN and St Joseph, WI. The first phase construction contract involves building the river pier substructures including groups of drilled shafts beneath each tower leg. A general location of the bridge project is provided in Figure 1.Prior to award of the construction contract, two separate design-phase axial load tests were performed on non-production drilled shafts with rock sockets. Both tests were static, bottom-up tests using the Osterberg Cell (O-cell). The first test was performed in 1995 when final design and construction was thought to be imminent. After years of public debate and literally, an act of Congress, design of the project was finally restarted and a second load test performed in 2012. The 1995 test was conducted on the Minnesota bank approximately 900 ft southwest of the St. Croix River bank. The 2012 test was conducted in the river about 2,100 ft northeast of the1995 test location. A plan-view of the project indicating the test program locations relative to the bridge alignment is provided in Figure 2."

Jan 1, 2015

By Swaminathan Srinivasan, Aaron J. Muck

"When an opportunity arises to combine state-of-the-art concepts with advanced modeling tools, engineers need to take what they know and apply forward thinking to geotechnical solutions to promote the state-ofpractice. Such an opportunity was seized during the design and construction of the Great American Tower in Cincinnati, Ohio. The forty-one story Great American Tower at Queen City Square – currently the tallest building in Cincinnati – has not only changed the downtown skyline, it is also contributing to the advancement of the state-of-the-art use of auger cast-in-place (ACIP) piles as settlement reducers. Predicted settlements of a traditional mat foundation were excessive, and the costs and construction time associated with traditional ACIP piles extending to bedrock were not preferred. A mat supported on a limited number of ACIP piles, with the piles primarily acting as settlement reducers, was evaluated as the preferred foundation type.Promoting the unique soil-structure interaction of the foundation system with confidence required the use of sophisticated numerical modeling tools. Traditional standard penetration test boring data (SPT) was initially used to develop a numerical analysis of the soil-structure interaction using FLAC 3D software. The model was further modified with cone penetration (CPT) and pressuremeter testing (PMT), along with actual load test results on several ACIP pile elements of varying lengths, but all tipping above bedrock. Through a combined design team effort, and detailed numerical modeling analysis, ACIP piles were recommended for reducing mat foundation settlement. Instrumentation during and post-construction confirmed design assumptions and predictions. Integrating sound geotechnical concepts, and using advanced geotechnical analysis and design methods, traditional mat and ACIP pile foundations were successfully integrated into a unique foundation support system.INTRODUCTIONThe Great American Tower at Queen City Square in Cincinnati, Ohio is located within a region dissected by historical geologic deviances associated with the meander of the Ohio River and glacial progression/recession. Combining a challenging geology, with the development of a high-rise office building afforded the design team an opportunity to combine state-of-the-art soil-structure interaction concepts and method with traditional geotechnical engineering concepts. Such a combination required a variety of field tests, collaboration with the design team and owner, and geotechnical-structural modeling during the design phase. During construction, in addition to materials testing and observation, a variety of instrumentation systems were employed. Together, the data was used to corroborate the design model and make adjustments during construction and further substantiate design assumptions following construction."

Jan 1, 2015

By Mingmei Zhu, Xin Qiu, Xiaofei Dou, Yu Wang, Tiancheng Lin, Bing Xie

In this study, the slag forming route of the single-slag steel melting when smelting medium phosphorus hot metal was investigated. The CaO-SiO2-FeO-MgO-MnO-P2O5 as hexahydric slag system was adopted in the converter. The effect of slag composition on liquidus was calculated by FactSage, the isogram of phosphorus distribution ratio was calculated by using the regular ion solution model, combining these two tasks, the theoretical slag forming route was obtained. Through experiments, the actual melting point ofthe corresponding components on theoretical slag forming route was obtained, in this way, the theoretical slag forming route was confirmed. Then, the theoretical slag forming route was applied to industrial test in a 210t BOF. After using the new slag formating route, the dephosphorization ratio was increased 3.6% while the auxiliary materials consumption was reduced, and the cost of steelmaking was reduced.

Jan 1, 2015