Search Documents

By H. Mengbing, A. Potokin, A. Usov

"Revealed and analyzed in the study are the ways of significant perfection of specific characteristics of the equipment, such as use of high-frequency voltage transformation to create a charger; use of pulse transformers, with core made of materials with high magnetic permeability, in pulse generating circuits; as well as use of special ways to produce voltage pulses with a short front. The experiments have proved the possibility to adapt these technological solutions for electric-pulse installations, and suggested on this base is a strategy of further development and application of electric-pulse technologies. The different applications joint work schemes of voltage sources with two levels voltage and energy in electric pulse technologies are investigated. The possibility of increasing energy efficiency of destruction is shown."

Jan 1, 2014

By Nikolaus Schneider

"Abstract: The combination of failure in joints of diaphragm walls and their exposure to water pressure may have far reaching effects ranging from water leakage to the risk of catastrophic loss of stability for the retaining wall and civil structures behind it. Investigations of imperfect joints in diaphragm walls have led to the development and testing of a quality tool to monitor the joint integrity of diaphragm walls during construction. By applying independent mechanical sensors (“joint inspector”) to the steel frame of hydraulic or mechanical grabs, it is now possible to record the surface conditions of exposed primary joints during the construction of secondary panels. This allows for the implementation of corrective action during the construction process should joint quality not indicate a watertight connection to the adjacent panel. The joint inspector, used for different types of stop ends, was tested on a full scale test field at several construction sites. The implementation of this new quality tool drives a new quality standard for deep excavations in inner city areas.General introduction to diaphragm wallsDiaphragm walls are reinforced concrete elements constructed using bentonite slurry to temporarily support an open trench in the ground. They are used in two main fields of application in civil construction, as foundation elements for vertical and horizontal loads (barrettes) and as retaining walls for excavation pits.Particularly for deep excavation pits in inner city areas, diaphragm walls are used as temporary or permanent walls of retaining walls. Alternative retaining wall systems would be secant pile walls, sheet piles or soldier piles, but these have disadvantages in structural strength when compared to diaphragm walls. If the vertical load of existing buildings next to the excavation pit has to be accommodated, the most practical solution can be found using diaphragm walls supported by prestressed anchors, steel struts or slabs."

Jan 1, 2014

By Cang Daqiang, Li Yu, Liu Xiaoming, Zong Yanbin

"Utilization of high-quality heat in melting slag is a great challenge for iron and steel industry. In the paper, a new method is put forward to concurrently utilize heat and slag by converting the melting slag directly into high valued materials, slag glass-ceramic. A glassceramic with a higher basicity of 0.7 than traditional basicity of 0.45 was prepared from steelmaking slag in order to utilize more hot melting slag. Effects of Alz03 on its crystallization processes were researched by XRF, DTA, XRD and SEM. Results show that Alz03 in glassceramic would have great effected on its property. When the Alz03 content ranges within 12%-15%, glass-ceramics with basicity of0.7 could reach the best performances. The change of dominant phase in glass ceramics from akermanite and wollastonite to akermanite and gehlenite would significantly degrade its mechanical property. An increase of Al2O3 content leads to a rise of the viscosity and crystallization activation energy of the glass, while results in increasing sintering temperature and crystallization temperature of glass, which contributed to its fully crystallization and densification process.IntroductionSteel slag is a by-product under a process of converting iron to steel at above 1600°C, and 0.1-0.15 ton molten steel slag would be discharged for producing per ton of steel in the process. The discharged steel slag at 1600°C has heat of 68 kgce/t. In 2012, China's steel output reached 716 million tons, and produces about 100 million tons of steel slag and 68,000 tee of heat in it [1,2]. But at present, utilization of both slag and its heat at 1600°C is a great challenge for iron and steel industry.Dry granulation of melting steel slag by air and then recovering the heat of the hot air are a traditional technology which have not yet been put into practice for very low heat conductivity of the slag and low efficient of heat exchange among the different processes [3,4]. Therefore, a new method for high efficient utilization of both steel slag and its high temperature sensible heat is put forward [5,6], which is on-line reducing and extracting iron from molten steel slag and then directly preparing glass-ceramic by use of the residual molten slag."

Jan 1, 2014

By T. Gong

Often plans to increase plant throughput provide an opportunity for optimising plant equipment and operating methods. This was the case in 2005 at TISCO Jianshan Iron Mine, when an increase in production was planned. The thickening circuit had presented a limitation to the plant throughput and operation with poor overflow clarity and underflow density. Following a course of test work by Outotec, a 53m diameter Supaflo® High Rate Thickener (HRT) was selected for the duty. From early stages of operation of the new thickener, the benefits have been dramatic, including: ? Improved tailings underflow density by 9% ? Improved Overflow clarity to less than 150ppm ? Considerably decreased the water and energy consumption as well as operation cost ? Stable and reliable operation This paper looks at this installation as a case study and compares the previous thickener installa-tion performance with the performance of the single 53m HRT.

Jan 1, 2014

By Thenepalli Thriveni, Seong-Young Nam, Nam-Il Um, Joobeom Seo

In the present work, we report a novel microstructure of synthesized scalenohedral PCC (precipitated calcium carbonate) without any additives by a simple and ecofriendly carbonation process carried out in a liquid-gas system on the crystal growth of the scalenohedral calcite phase. Especially, the process parameters of Ca(OH)2 concentration and CO2 flow rates were investigated to enhance the sensitivity of the process. The highest average length of the scalenohedral calcite was obtained at pH 6.0, temperature 450C, Ca(OH)2 concentration 0.2M, CO2 flow rate 80mL/min, and total volume 1L. The utilization of flue gas-derived CO2 from coal fired power plants could be a form of carbon capture and storage using carbonation reaction with scalenohedral PCC. Finally, the synthesized scalenohedral PCC was used as a filer for ONP recycling. We demonstrated all these experiemnts at semi pilot plant scale.

Jan 1, 2014

By Fengming Li, Baocheng Song, Yuemin Zhao, Hailin Dong, Liping Peng, Chusheng Liu, Chenlong Duan

The large-scale vibrating screens with high processing capacity and efficiency are now in great demand in the mineral processing industry of China. However, as the equipment is always suffering from the strong external harmonic exciting force, the inertial force and the impact from the minerals, the fracture of the beam and the crack of the lateral plate are easy to occur, which has a negative effect on the reliability of the equipment itself and the industrial production. Considering the essential high reliability of the equipment, a new large-scale vibrating screen with duplex statically indeterminate mesh beam structure (VSDSIMBS) was developed. The natural characteristics, namely, the natural frequency (or the modal frequencies) and the natural mode, and the dynamic characteristics of the VSDSIMBS were obtained by the modal analysis and the harmonic response analysis. In addition, the dimensions and the constructions of the statically indeterminate plate and the mesh beam were chosen as the design parameters, to which the sensitivity of the whole mass, the maximum deformation and the maximum stress of the duplex statically indeterminate mesh beam structure (DSIMBS) were summarized for the optimization of the DSIMBS. Now the large-scale VSDSIMBS is being well used in China.

Jan 1, 2014

By S. Nitta

The present study deals with a new approach in calculating the size of Tower Mills. The method is derived from the application of grinding kinetics theory on the analysis of by-gone operational data. It requires only information on the capacity of the mill to be designed, the product fineness and the Bond?s work index to give an accurate and simple prediction of Tower Mill characteristics. An example illustrates the different steps of calculation.

Jan 1, 2014

By T Duff

This paper describes results from small scale tests conducted to determine the distribution of pressure on target plates when subjected to loading due to the detonation of a buried mine in various media. The tests are conducted by using saturated sand, dry sand, and water as the loading media. Different stand-off distances are investigated. Kolsky bars and pressure sensors are used to determine the free-field pressure - time profile of the output of the charge at any location on the vehicle bottom. For verification of the pressure results at certain distances, the specific impulse measured by utilizing different size round plates are employed. In order to investigate the loading mechanisms, high speed cameras are applied. The small-scale test results can be scaled to full scale by using verified scaling laws.

Jan 1, 2014

By Vincent Joannes, Marine Lasne, Luca Brenelli, Colin Serridge, Inge van Baardwijk, Martin Stanley, Anthony Fisher, Mary Ellen Bruce, Tony Suckling, Pedro Avellanosa

"Abstract The European Federation of Foundation Contractors (EFFC) and Deep Foundations Institute (DFI) developed a sector-specific carbon accounting methodology and associated “carbon calculator” for foundations and geotechnical works. The EFFC-DFI Carbon Calculator is believed to be one of the construction industry’s first collaboratively produced carbon calculator tools for European and international countries based on verifiable and standardized data. It is intended that the tool be adopted internationally and become the open-source industry standard for ground works. A detailed methodological guide is provided with the calculator (Lemaignan and Wilmotte, 2013). This guide explains the background of the standards, accounting methodologies, emission sources and factors that were used as the bases for the tool development and includes detailed guidance on use of the calculator.Drivers for DevelopmentFoundation contractors anticipate project cost and carbon emissions will become inextricably linked in response to the climbing price of fossil fuels and carbon intensive materials as resources become scarce. Low carbon solutions will therefore become more competitive options. Also with high profile construction projects having low carbon/carbon neutrality as requirements, sustainability in the foundations industry also becomes a market issue.This carbon calculator will be used to lead the industry and shape the expectations of commissioning organisations by providing insight into the carbon cost of their projects. Commissioning organizations are encouraged to be aware of the carbon impact of projects and to also facilitate a fair and accurate way of comparing footprints to provide a level playing field for foundation contractors."

Jan 1, 2014

By Z. F. Hu

Tourmaline has the characteristics of piezoelectricity, thermoelectricity, spontaneous polarization and far-off infrared radiations. Ultra-fine powders of tourmaline have extensive applications in the fields of electron, chemical and environment protection, as well as health protection. The preparation technology of ultra-fine tourmaline powder is discussed. The key equipment of a pilot plant for producing ultra-fine tourmaline powder with jet mill and stirred ball mill is described. Using this pilot plant facility it is possible to produce tourmaline powder with particle size smaller than 100 nm, and a continuous production process can be realized. The final powder product has many superior performance such as high whiteness and large specific surface area, and it?s a negative ions emission can reach the value of 7190 ions per cubic centimeter.

Jan 1, 2014

By Lorraine Kent

Excessive floor and side deformation are major problems in deep coal mine entries in Europe, and in particular in the UK where rockbolt support is used at depths of working of around 3000 ft. This has major economic and safety implications for the industry resulting in the potential for sidewall instability, disruption to mine infrastructure, (belt conveyors, floor mounted transport systems and powered supports), and the requirement to safely manage excavation of large quantities of floor material. European research aimed at improving deformation control is described. The outcomes include innovations in support systems, materials and installation practices, as well as better methods for predicting and monitoring deformation levels. As coal mines get deeper, some entry deformation is inevitable, and methods for mechanised removal of floor lift and repair of sidewalls have been developed to allow production to continue as mining clearances are re-established.

Jan 1, 2014

By R. MacRosty, R. Pula, P. Gebski, W. Braun

"This paper provides a progress update on three tapblock monitoring technologies that Hatch has been developing with our clients for non-ferrous smelting furnaces.The Tapblock Diagnostic System (TDS) is an advanced on-line monitoring system that uses temperature data along with embedded thermal model results to evaluate the condition of a tapblock over its campaign life. Hatch recently installed a second Tapblock Diagnostic System, some details of which are provided in this paper.The Tap-hole Acoustic Monitoring (TAM) system is installed on water-cooled copper tapblocks and uses the noise from the tapping channel to provide a qualitative indication of wear and deterioration of the tapping channel refractory. In addition, TAM can be used to monitor drilling and lancing performance, and potentially could also be used in the future as a guide for automatic drilling and lancing systems (Sadri et al., 2008).The third technology is the use of fibre optic sensors to measure temperature on the hot face and in the tapping channel of a tapblock. Fibre optic technology allows installation of numerous sensors in key locations where they are very sensitive to tapblock condition and also provide more extensive spatial coverage than is possible with traditional instruments. This paper provides an update on our efforts to address issues with premature failure of the sensor cables due to corrosion, and also converting the vast amount of data from the sensor cable into information that can be used by furnace operators."

Jan 1, 2014

Separation performance of a Floatex Density Separator (FDS) has been studied both experimentally and theoretically. Experimental results reveal that at a lower bed pressure the FDS acts like a classifier. Higher bed pressure is required to attain the concentration effect as proper development of suspension density occurs under these conditions. It is seen that the size or density alone is not able to describe the partition fully. The terminal settling velocity, which includes both the size as well as the density of the particle can be a useful descriptor of separation in a FDS. While a narrowly distributed feed offers better performance of a FDS, a wide size distribution of feed results in large scatter in the terminal settling velocity distribution and renders the separation difficult. The closely sized feed enhances the density effect in concentration. A higher teeter water flow rate also helps in carrying larger-lighter particles to the overflow by increasing the cut off terminal settling velocity as it increases the net upward force. A detailed description of separation performance in a Floatex Density Separator has also been established from theoretical considerations. Separation performance of the separator is described using a simple slip velocity model. The model has been validated com-paring the predicted FDS performance results with those experimentally measured under widely different operating conditions.

Jan 1, 2014

By D. Limpitlaw

The origins of mine closure practice have influenced the way in which it is implemented by companies and regulators. Mine closure practices essentially started developing in the 1970s in countries with advanced economies and mature mining industries. In these settings, the emphasis was justifiably placed on restoration of the landscape and an attempt was made to return to the ?natural? pre-mining land cover. These practices continued to evolve and incorporated socio-economic and cultural aspects, especially after the Brundtland Report in 1987 and the subsequent Earth Summit in 1992. Today mining is increasingly occurring in remote parts of developing countries where there may be significant need for infrastructure such as roads, clinics, and schools. The costs of returning land to low (economic) value pre-mining use may be far greater than establishing a viable postmining land use that could potentially add value to the community and take pressure off sites for greenfield development elsewhere. Furthermore, natural resource limitations (such as topsoil availability) may limit the degree to which the historical land cover can be re-established. Establishing post-mining land uses may aid in mitigating the loss of employment that is inevitable when mines close. Stakeholder participation in establishing post-mining land cover and land use options is critical for long-term success. Similarly, third parties must be identified to support the development of the post-mining land use This paper draws on the experience of the authors in several developing countries and presents a case for maximizing re-use of mining infrastructure. The paper does not advocate the adoption of poor rehabilitation standards, nor or the wholesale destruction of land capability, but rather leaving key infrastructure in place for post-mining use that may support sustainable development.

Jan 1, 2014

By F. Q. Dong

According to the principle that should be originated from nature, compatible with nature, used in nature and back to nature and based on conception of designing of eco-material, the author combined the ideas of material, environment, zoology and healthy. Properties of natural mineral materials were used to produce micro-aggregate elements by bionic method, so its components and function could accord with living environment. Eco-mineral functional materials which can adjust, purify and optimize the microclimate were reviewed. The authors pointed out the multifunction, com-pounding, the compound characteristics and integration regularities of micro-aggregates. It was the first time in the world to put forward the ?gene? technique or ?material chip? technique of manufacturing function micro-aggregates and eco-function elementary materials. The results of this re-search supported by the national ?863? Hi-tech Project, mainly including the high-efficient air purifying mineral compound material indoor, the clay elementary antibacterial materials, the masonry cement/coating/putty/compound with preventing radon radiation, environmental friendly composite functional coatings, mosquito repellent and healthcare material and zeolite-based energy-saving composite materials, were introduced. Finally, the foreground of mineral materials in the field of future advanced eco-friendly materials was also discussed.

Jan 1, 2014

By S. Gerl

Since Schönert, 1980 a multiplicity of scientists have dedicated themselves intensively to the scientific investigation of wet grinding in agitated media mills. The achieved research results led to a clearly improved understanding of the comminution mechanism in wet operated agitated media mills and in consequence also to clearly more efficient machines. In contrast to this the standard of knowledge on dry grinding in agitated media mills is still very small. The practical experience from numerous plants shows however that the transferability of knowledge from wet grinding to the dry grinding regarding transport phenomena and comminution behaviour, influence of the operating parameters and also wear is very limited. In the industrial application above all the continuous mode of operation is preferred. The main problem which has to be solved in agitated media mills is minor the comminution itself, than rather the question of the trouble free material supply and material extraction as well as the cooling of the mill. The agitated media mill MaxxMill® offers an innovative concept to overcome the feeding and extraction problem with its rotating grinding chamber, the eccentrically mounted agitators as well as the eccentric flow deflector with integrated material supply. Because of the pneumatic extraction of the ground materi-al cooling of the milling chamber is not necessary. On a MaxxMill ® laboratory mill with a 5 litre grinding chamber volume extensive parameter studies were carried out to study the influence of operating parameters on the continuous dry grinding of quartz sand. The test were performed in a continuous single pass operation without classification of the final product. Apart from the influence of the throughput rate on fineness above all the influence of the agitator and grinding chamber speed as well as the grinding media size was examined.

Jan 1, 2014

By S. Banisi, E. Arghavani, Gh. Parsapour, S. Mousavi

Maximization of water recovery in thickeners is an essential step in the mineral processing industries. The Gol-E-Gohar iorn ore processing plant uses a center pier thickener with a diameter of 38 m and depth of 4 m. The feed rate is 50 t/h solids with a concentration of 5% (w/w), and it has been designed to provide an underflow containing 50% solids. The performance of the thickener was not as expected judged by the overflow stream containing 0.6% solids and water loss of 52 m3/h in the underflow. A criterion called the index of flocculation incorporating the perimeter-based fractal dimension of flocs, floc size, and settling velocities was proposed and used to determine the optimum flocculant dosage which was found to be 20 g/t. The fractal dimension of flocs in a pulp containing 5% solids was found to be between 1.16 (no flocculant) and 1.56 (40 g/t flocculant) which indicated highly branched and loosely bound structures for the flocs as flocculant dosage increased. At these conditions, the size of the flocs which was recorded by a digital microscope increased from 93 µm to 403 µm. A new feedwell with a special design with the aim of preventing flocs breakage and maximizing energy dissipation of pulp was constructed and installed. These modifications led to an increase in the thickener drivehead torque from 5% to 18% of the rated torque, indicating a higher bed depth. Finally, installation of a PID controller reduced the drivehead torque relative oscillation from 52.0% to 12.7%. These changes increased the solids concentration of the underflow from 49.0% to 56.9%, decreased the overflow solids concentration from 0.6 % to values smaller than 0.01% and resulted in a reduction of 27% in water loss in the thickener underflow.

Jan 1, 2014

By Robert Hopler

Blasting powder is a slow-acting, black, granular explosive made of sulphur, charcoal and either potassium nitrate (saltpetre) or sodium nitrate. The blasting powder containing potassium nitrate is known as “A” blasting powder; that containing sodium nitrate, as “B” blasting powder. “A” blasting powder is a little denser, a little stronger and a little less hygroscopic than “B” blasting powder.

Jan 1, 2014

By Shuqiang Guo, Dingsheng Tan, Weizhong Ding, Zunyu Hu

"The mixture of hydrochloric acid and magnesium chloride is a good lixiviant for leaching of laterite. The solution can enhance the leaching ability because of the proton activity deviated positively from ideal. Otherwise, the existence of magnesium chloride in the lixiviant affects the dissolution behavior of magnesia, which may be an advantage of the process with less hydrochloric acid consumption. An investigation of magnesia particle dissolved in strong hydrochloric acid solution has been conducted. Influences of concentration of the magnesium chloride and hydrochloric acid and temperature on magnesia dissolution were studied. The dissolution mechanism was also discussed in this paper.IntroductionThere has recently been much interest in the use of hydrochloric acid leaching processes for recovering metal from ores or secondary resources [l-41_ Compared with sulfuric acid, the use of hydrochloric acid as lixiviant offers significant advantages including faster leaching kinetics even at atmospheric conditions, higher leaching rate and greater solubility for most metal chlorides [5-61 .With the gradual decline of the nickel sulfide supply, the extraction of nickel from laterites has become increasingly attractive [7-s1. Nickel may be co=ercially recovered from laterites both by pyrometallurgical and hydrometallurgical processes. The drawbacks of pyrometallurgical processes include the requirement of high grade ores, substantial energy input and loss of cobalt bound within ores. The extraction of Ni from lower grade nickel laterites ores is suited by hydrometallurgical routes, which play an increasingly important role with depletion of higher grade deposits."

Jan 1, 2014

By Graeme J. Jameson

"When mineral particles are floated in a mechanical flotation cell, it is found that the rate constant, after reaching a maximum value, starts to decline as particle size increases. It had been thought that the reduction in rate constant had been due to the increased prevalence of composite particles in natural ores, for larger particles. However, Jameson (2012) showed that the rate constant for composites is certainly a function of the surface liberation, but the reduction in flotation rate is independent of particle size. Thus all particles are equally affected by reduced surface liberation, independently of their size. He further argued that the classical peak observed in the rate constant with increasing particle size, is a function of machine hydrodynamics. Thus in mechanical cells, the peak may be due to the high energy dissipation rate and its effects on the detachment of particles from bubbles (Goel and Jameson, 2012). Consequently, in a different flotation environment, it may be possible to float large composite particles that cannot be floated in mechanical cells. This paper describes the flotation of large composite particles in a fluidized bed flotation cell. The particles to be floated are fed to a column in which there is a continuous upflow of liquid. A conventional froth layer of controlled depth is formed at the top of the vessel. A fluidized bed of particles is established which provides a gentle environment for the contacting of large particles with bubbles. An example is given where a porphyry copper ore was prepared at a top size of 710 µm, and floated with conventional collector (PAX) and frother (MIBC). The concentrate was separated into size fractions and examined by photography. Composites were observed at all size fractions, but above 400 µm, all particles were composites. The implications for future flotation circuits will be described."

Jan 1, 2014