Search Documents

By J. D. Stinnette

Traditionally, airflow requirements for diesel equipment operating in underground environments such as mines and tunnels were determined by multiplying the vehicle power by a ventilation rate that was either mandated by regulations(s) or determined empirically from known quantities. In some cases, utilization factors were further used to adjust (reduce) the total airflow calculations for a diesel equipment fleet. However, in light of the drastic reductions to diesel equipment emissions mandated by the US EPA Tier IV and EURO Stage 4 regulations, there is currently a great deal of uncertainty in the underground mining industry among those responsible for the ventilation of planned new mines or the expansion of current mines. Tier IV engine standards mandate a reduction of DPM and NOx of approximately 95%, but can ventilation rates at mines with Tier IV equipment (or equivalent) really be reduced by a factor of twenty? This paper outlines some of the factors that affect the airflow required for the ventilation of modern diesel-powered equipment and examines how they can be applied in determining a reasonable ventilation rate for Tier IV compliant equipment operating in subterranean environments.

Aug 1, 2013

By Ali Montaser

This paper presents an experimental study conducted to facilitate the use of RFID on construction job sites. The study focuses on deployment settings to provide data acquisition with higher accuracy for indoor location sensing. It provides extension to the state-of-the-art in this field as it addresses the impact of metal media proximity to RFID tags, the reasonable duration for data capturing, number of RFID tags employed and the distance between them. Low cost passive RFID tags were used in the experiments where each tag is used as a reference point with a known location. Five hundred and forty (514) experiments were conducted in lab environment using a 3m by 3m test bed that is dynamically rearranged to generate 15 test beds and a total of 67713 data sets were collected and analyzed. The collected data were captured from nine locations for each test bed at four time intervals. Received Signal Strength Indicator (RSSI) was used as the main attribute for signal measurement to process the captured data. Results of the data analysis performed are studied under four main categories: duration, number of tags, locations of tags and metal interference. The best duration was found to be the 15 second in the test bed with the least number of tags; as the short amount of time to capture data did not allow creation of a lot of interference among the emitted signals. Within each test bed, errors occurred most at points where the received signals were not well distributed in a 360 degree vicinity of the data capturing point. It means that the center point of each test bed resulted in lowest errors and the points located on the extremities led to the highest errors. Finally, metal objects were found to have major impact on the accuracy of the captured data; to the level where reliable values for errors could not be calculated in the test beds attached to metal objects. In summary, the results of the experimental study and related findings are expected to provide guidelines to the users of RFID technology for localization in building construction.

Aug 1, 2013

By D. Fodor

In Romania, there are significant lignite and brown coal reserves hosted by different regions of the country. The most important lignite bearing zone of the country situated in the North ? West part of Oltenia region and which covers a surface area of 2,500 km2 and host a total reserve of 3.0 billion tons of lignite, of which more than 95% can be exploited by open cast method. The paper deals with the existing geological and mining conditions of the zone , the distribution by mining basins and exploitation perimeters, the open cast working technologies and the economic outcomes obtained throughout the time. Years ago, for the improvement of the economic situation as a whole and in each unit, a large production reorganization, technology update and modernization process was started up. There are described the rehabilitation measures of the technological lines and modernization of the equipments of the production flow-sheet, measures developed at present, too and which will still continue in future. There are mentioned the equipments considered, the components under modernization and the economic outcomes obtained so far. At the end of the paper there are presented the future actions for the equipment modernization and perspectives of the lignite deposit exploitation to meet the national economy requirements of solid fuels.

Aug 1, 2013

By A. Torkian

Copper mining operations have increased in Iran in the past decades due to price increases and potential for creating jobs in developing countries. Iran consists of many copper mines. The mining operations have a positive economic impact on the region, but may also be the cause of adverse environmental effects. Environmental aspects and the health impact of respirable particulates on the communities and agricultural production in the immediate vicinities have been under scrutiny by the regulatory agencies to ensure sustainable development. The impact of an open-pit mine on the air quality and extent of particulate pollutant dispersion in different directions and times is the focus of this paper. The results of the modeling have been validated through ambient air monitoring. Monitoring stations were installed in different areas within the mine unit operations and around it including background areas where PM10 values were 7 µg/m3. Outside the Complex, particulate concentrations were monitored in 9 different stations and up to 25 km distance. Modeling of point, area, and volume sources was conducted using a 9- year meteorological database. The results showed that particulate quantity decreases rapidly below local standard value of 150 µg/m3 at 2.5 km around the mine and the main pollution is due to the crusher and tailings dump areas. Model outputs were compared to the actual values measured by the air quality monitoring network including villages and crop fields. High overall correlation of about 76% was obtained for most of the locations but lower values were reported for more complex terrain in the region. Remedial actions recommended included road water spraying and better management practices to avoid overloading trucks.

Aug 1, 2013

By C. Mawdsley

The Tata Steel mill at Skinningrove in the North East of England produces top hat sections for mineshaft guides in sizes 102 and 150 mm. The top hat section is the technically preferred shaft guide choice for modern deep mine shafts. This paper explores the relative service performance of top hat and square hollow section guides in service. Comparative corrosion performance is reviewed and the paper describes work commissioned by Tata Steel (as Corus) undertaken by Aker Kvaerner Engineering to evaluate relative winding speeds, relative loads and fatigue life in service. The experience of supply to UK Potash mining is discussed and the future view of high capacity hoisting and larger section size market need and availability is assessed.

Aug 1, 2013

By R. M. T. Raja Ismail

Shipping and stevedoring industry is going to witness a massive increase in the amount of containers to be handled while land constraints become more critical. Offshore transfer operations hence offer a preferable solution to deal with the surge in cargos rather than to expand the port outwards. Recently, there has been increasing research interests on offshore crane automation. Suspended cargos in a ship-mounted crane system are caused to swing due to the vibratory motion of the ship induced by ocean waves, which can lead to collision between cargos and deck. Therefore, it is vital for offshore crane systems to satisfy rigorous requirements in terms of safety and efficiency. This paper presents the modelling and control development for offshore boom crane systems. A second-order sliding mode control law is proposed for trajectory tracking and sway suppression control, making use of its capability of actuator chattering alleviation while achieving high tracking performance and preserving strong robustness. The asymptotic stability of the closed-loop system is guaranteed in the Lyapunov sense. Simulation results indicate that the proposed controller can significantly reduce the effect of disturbances coming from gusty waves and other dynamic loadings.

Aug 1, 2013

By S. Leong

This paper reports on research examining disclosures from mining companies regarding their water usage in the Macquarie and Lachlan catchment areas, both parts of the Murray-Darling Basin in New South Wales, Australia. The objective of the research was to assess whether this disclosure is sufficient to allow communities to determine whether mining companies are complying with mining conditions of consent and abiding by the requirements of their water licencing agreements. These requirements are then compared to the water reporting requirements of the Global Reporting Initiative (GRI) and the Water Accounting Framework for the Minerals Industry (WAFMI). Communities are concerned about whether the mining industry?s use of water will have impacts on their livelihoods and lifestyle and thus require information concerning the quantity of water that will be extracted, how much water will be left for other stakeholders and whether the mining will affect water quality. This is an archival study. It has involved examining relevant publically available information released by mining companies and government regulators and determining if this is sufficient to meet the needs of the local communities. Additionally, it has involved looking at information indirectly provided by mining companies, via the use of intermediaries. Further, information availability concerning basic water accounting and regulatory breeches and whether such information is available at the mine site level has been considered. It is found that while NSW legislation places very little reporting requirements on mining companies, the development consent conditions for new projects and extensions to existing projects are quite significant and should be sufficient to meet the needs of local catchment residents though such information is not always easily accessible for the layperson.

Aug 1, 2013

By R. E. Bou Serhal

Many miners are exposed to dangerously high levels of noise on a daily basis. Over the past 15 years, a continually increasing number of occupational hearing loss has been reported from the mining community in the United States, of which, more than 95% is attributed to prolonged noise exposure. Although the noise exposure levels may differ between coal miners and metal and non-metal miners, in the absence of noise control at the source, the solution is the same: use of personal hearing protection devices (HPD). While protecting the miners? hearing it is also essential to no longer hinder their ability to communicate. With access to an advanced HPD that is customized to the miners? ears we are able to combine these two requirements. Using an intra-aural instantly custom molded HPD miners are protected from high levels of noise. The HPD is equipped with wireless capabilities, and contains both a speaker and an In-Ear Microphone (IEM). Therefore, the miners? speech may be captured from inside the ear and transmitted to the remote listener. This IEM signal is relatively noise-free since it is isolated from the background noise. The IEM speech signal, however, is ?boomy? and is missing some high frequency content, making fricative consonants hard to understand. Nonetheless, the IEM speech signal is correlated with the natural speech signal and may be manipulated through statistical techniques to more closely resemble natural speech. By improving the intelligibility and quality of the IEM signal, numerous applications may be enabled. One use of the enhanced IEM signal will be for radio communication. Using wireless radio communication in a noisy mining environment is sometimes the only practical and affordable solution to allow communication between miners equipped with personal hearing protection devices. Traditionally, one of the weaknesses of such wireless radio communication lies in the lack of designating receivers: whether they are the intended receiver or not, all those carrying a radio receiver are subjected to the broadcasted signal. The current work will detail a new concept of a "radio-acoustical virtual environment" where the radio signal will only be received by miners within a given spatial range, such range depending on the user?s vocal effort as well as the ambient and perceived background noise levels.

Aug 1, 2013

By Youngjib Ham

Understanding energy performance of existing buildings is vital to increasing their efficiency and reducing the overall energy consumptions. This entails facility managers to systematically monitor building energy performance and reliably identify and analyze potential problems. Currently, infrared thermography is widely used as a primary diagnostic tool for the detection of building performance problems. Nonetheless, applications of thermal images for building inspection are mainly restricted to manual and labor-intensive identification and qualitative assessment of heating or cooling loss. Automated identification of potential problems and reliable cost analysis of the associated energy loss can help homeowners to minimize financial risk of retrofits and maximize energy savings. To that end, this paper presents a new automated method for calculating the cost of energy loss for building diagnostics. In the proposed method, first, using a hand-held thermal camera, the auditors collect digital and thermal imagery from the buildings under inspection. Then, using a recently proposed method for Energy Performance Augmented Reality (EPAR) modeling, an actual 3D spatio-thermal model is generated and superimposed with a computational fluid dynamics (CFD)-based expected energy performance model. The resulting EPAR model is placed into the method proposed in this paper for cost analysis of the energy loss. Through a new 3D thermal mesh modeling using k-d tree structure and nearest neighborhood searching, performance deviations between these models are automatically calculated. Using a temperature threshold, the areas associated with potential performance problems are detected in the EPAR model and are visualized using a metaphor based on traffic light colors. Then, the actual R-values of the detected areas are measured at the level of 3D points. Based on the measured R-values and the estimated air change rate for the detected air leaks, (1) the heat loss or gain caused either by poor insulation or air infiltration/exfiltration and (2) the associated energy costs are automatically calculated. The proposed method is validated on several locations of existing residential buildings. The preliminary results show the potential of the proposed method for minimizing the inspection time as well as the risk associated with the cost analysis of retrofitting potential building performance problems.

Aug 1, 2013

By Andre L. Du Preez

Global mine hoisting regulations require safety fall arrest systems to be installed on vertical conveyance systems capable of safely decelerating and supporting a fully loaded conveyance in the event of a rope severance. Most current arresting systems are incapable of producing controlled safe deceleration rates. Although safety ?dogs? achieve marginally acceptable results on wooden guides, difficulties arise in achieving safe deceleration performance requirement where safety arrest systems operate on steel shaft guides. Previously, arresting systems capable of operating with steel guides have been incapable of producing controlled deceleration rates during the arresting of free-falling conveyances. Most are ?instanton? systems, whereby an occupant inside a conveyance being arrested would be subjected to unacceptably high deceleration forces. This paper briefly highlights the background to the selection process of Rio Tinto?s Technical Staff of a suitable Mine Conveyance Safety Fall Arrest System for #1 Shaft at Rio Tinto Oyu Tolgoi Mine, Mongolia. It also describes the Drop Test and Free Fall Test procedure and the results leading to the acceptance of the Horne Group Levelok® Emergency Braking Technology for the Oyu Tolgoi #1 Shaft in Mongolia. The paper highlights Rio Tinto?s primary objective for the selection of this advanced technology on their primary production shaft cage system as an emergency safety catch braking system combined as an advance hydraulic chairing system. It describes the design and operational parameters and the 'Fail to Safe' interfacing with current automated mine hoist systems.

Aug 1, 2013

By K. Szczesny

This paper considers the integration of uncertain real-time logistics data for reactive construction scheduling. In order to manage a construction project efficiently, an accurate schedule representing the current project progress is inevitable. The quality and up-to-dateness of such a schedule depends on the availability of real-time data. Typically, real-time logistics data contain information about the availability of material, equipment and personnel as well as delivery dates and site conditions. The accuracy and inherent uncertainty depends on the location where the real-time data was acquired. Currently, the integration of such data into a construction schedule is a very time-consuming, manual and, thus, errorprone process. Therefore, this paper proposes a methodology that enables an automatic integration of such uncertain data into construction schedules. By integrating uncertainties into the existing schedule their impacts on the construction work can be evaluated. For this, discrete event simulation is applied. In order to model uncertain input parameters for simulation models this methodology applies the fuzzy sets theory. In combination with alpha-cut sampling technique, discrete model input parameters are obtained. By applying reactive scheduling with several discrete event simulation experiments, the results can be used to modify construction schedules according to agreed timeframes and costs. In order to demonstrate and validate the presented approach an example is conducted.

Aug 1, 2013

By A. Grimod

The European Guideline ETAG 027 - 2008 (?Guideline for European Technical Approval of Falling Rock Protection Kits?) defines the procedures to test rock fall barriers. Nowadays, this guideline is essentially the only test and construction framework utilized by manufacturers and it is also starting to enter in the mentality of designer who can clearly specify the performances of rockfall barriers. ETAG 27 (and the related European Technical Approval and the CE marking) represents a milestone for the rockfall barrier market, because it gives the possibility to compare the performances of different fences and it ensures the quality of the certified product. For these reasons ETAG 27 presently constitutes the base for tenders all around the world. Although rockfall barriers are in common use, designers and consultants do not have a clear overview of the real performances and the technological limits of these structures. The first problem can be solved using ETAG 27 criteria, which allow designing rockfall barriers at ultimate and serviceability limit state. Even though ETAG 27 uses crash tests performed with the Service Energy Level (SEL) and Maximum Energy Level (MEL), design with these concepts is not obvious or in common acceptance. Some preliminary questions must be solved. When can these energy levels be correctly applied? In the case of rockfall simulations, what probabilistic approach must be used for the evaluation of the barrier? Unfortunately ETAG 27 does not give any information or tests relating to the technological limits of the fences. Therefore some important questions arise. How do the site specific aspects of installation affect the barrier performance? What is the behaviour of the barriers under extreme conditions? And finally, the main question lies in the background: what is the functional reliability of ETAG 27? All of the above questions require comprehensive answers, which is consistent with the experience of designers, installers and producers. Officine Maccaferri S.p.A., with its 130 year experience in the field of rockfall protection, collected a large number of case histories with barriers impacted by single or multiple blocks, debris flows, and snow avalanches. Throughout these case histories and in accordance with a recent Italian standard code, it has been possible to implement a reasonable design approach that considers the efficiency of the barrier, the uncertainties of the input data, and the fore

Aug 1, 2013

By Mosquera. J.

Tailings Storage Facilities (TSFs) are vast structures that respond to site-specific characteristics, rate of production, placement techniques, and the physical and mechanical properties of tailings. As a common denominator, TSFs are in some degree vulnerable to failure due to liquefaction, poor management, slope instability and/or unusual climatic events. In practice, stability of TSFS is determined by calculating a minimum Factor of Safety (FOS) using the Limit Equilibrium Method (LEM). However, it has been proven that relying exclusively on the limit equilibrium approach is not accurate because it is basically a static method that does not take into account the stress-strain distribution and displacement experienced by the constitutive materials of a TSF. In order to overcome these limitations of the LEM, the finite element method - Shear Reduction Technique (SRT) has been used as a more reliable tool for TSFs stability assessment. This paper presents a comparative stability analysis between an upstream tailings storage facility (UTSF), and a water retention tailings dam (WRTD) under static and pseudo-static states using simplified and rigorous LEMs and the SRT. Additionally, and taking into consideration the intrinsic uncertainty of tailings properties, sensitivity and probabilistic analyses in the form of Monte Carlo Simulation (MCS) and the Point Estimate Method (PEM) are applied to determine the Probability of Failure (Pf) and Reliability Index (ß) of each TSF. It is shown that the friction angle of UTSF?s foundation and the core?s cohesion of the WRTD are the main variables that govern stability. Further analysis shows that the WRTD has a higher reliability index and a lower probability of failure than the UTSF.

Aug 1, 2013

By Nehad Elsafty

It is always necessary to expand existing buildings, so that they could meet the growing societal needs. Compared with demolishing them and then constructing new ones, the expansion of existing buildings could not only reduce project cost, but also save the use of energy and raw materials in projects. Therefore, it is widely adopted in most under-developed countries. However, the expansion of existing buildings is not an easy task. It has been involved with a lot of issues in defining the scope of work, planning landscape, managing construction activities, etc. This paper investigates the potential challenges in expanding existing buildings. The project of expanding the Al-Agoza Hospital, one of the biggest and oldest hospitals in Cairo, Egypt, is selected as a case study. In the case study, the project documents have been carefully reviewed. The project engineers and the health-care professionals working in the hospital have been interviewed. This way, the point of views from the owner, the architect/engineer, and the contractor have been taken into account. Several lessons are learned through the discussion with these people. The results from this paper are expected to provide pieces of useful advice and suggestion for the expansion of existing buildings in the future.

Aug 1, 2013

By F. Bosché

Previous research has shown that ?Scan-vs-BIM? systems are powerful to provide valuable information for tracking structural works (progress, quality, safety). However, the transferability of this capability to other construction areas such as MEP works has not been assessed so far. Comparatively, the construction of MEP systems, in particular pipes and ducts, tends to be more flexible with respect to the positioning of individual components, so that Scan-vs-BIM systems could be defeated when tracking MEP installation works. This paper presents recent results on the feasibility and performance of using a Scan-vs- BIM system to track MEP works. The approach followed is presented and then tested with two real-life challenging case studies were conducted simultaneously but totally independently in Canada and Italy. The results show that, as expected, pipes and ducts tend to be more loosely positioned than structural elements leading to a poorer performance of the Scan-vs-BIM system. Nonetheless, it appears that the system works well to assess the level of conformance of site installation works, providing valuable information for estimating emerging performance metrics like ?percent built as-designed?. In addition, the proposed system could also be useful to accelerate and thus reduce the cost of delivering as-built BIM models for in the case of new builds.

Aug 1, 2013

By Yoginder P. Chugh

This paper discusses design of sprays systems for dust control around a continuous miner (CM) in about 4.2 m (14 ft.) high mining areas with about 1.0 m to 2.0 m (3-6 ft.) of out-of-seam dilution mining. The challenges included low air volumes and velocity at the end of the line curtain, dust produced from out-of-seam dilution rock being very fine with 50% of the particles less than 10 micron, poor capture of aerosol through scrubber suction inlets, dust escaping through the sides of the loading pan in mining high areas, overloading of dust-laden air in the wet-scrubber, and dust rollback toward workers. The challenges were resolved through CFD modeling of airflows; improved line curtain installation, redesign and varying the spatial locations of spray systems as compared to low mining height areas. Water sprays on CM is the primary engineering control for dust control in coal mining. In 2010, the authors developed several spray system concepts for dust control (Chugh, Patwardhan, Gurley, & Hirschi (2009), Chugh & Gurley (2009), Chugh 2012). These included increased contact time between dust particles and water droplets, improved potential for the dust aerosol to be sucked in through suction inlets, and reduced dust-roll back to the operators and workers. CFD modeling was used to understand airflow patterns around mining areas and to identify spatial locations for sprays to minimize dust exposure of CM operator (CMO), haulage unit operator (HUO), and workers downwind of the operating CM in the last open crosscut (LOXC). Face area ventilation plays a key role in dilution and removal of dust generated by mining operations. High mining heights and large pillar sizes associated with longwall mining reduce the air volume reaching the face area to achieve good dust dilution.

Aug 1, 2013

By J. A. Dubinski

One of the greatest threats of mining in hard coal mines are underground fires, which in the past often resulted in the mining disasters. Implementation of scientific principles of fire fighting into practice contributed to a significant reduction of fire hazard in coal mines. However, despite numerous achievements of science in the fight against the underground fires, they still occur creating a potential hazard for the miners and contributing to generate significant costs of fire-fighting operations, the temporary suspension of production or loss of longwalls. This concerns both spontaneous fires and exogenous ones. A significant decrease in the number of spontaneous fires was the result of cooperation between Polish scientists with experts in the field of new methods of fire hazard prediction and selection of new fire prevention and fire hazard monitoring methods. A significant part played here researchers from the Central Mining Institute. The original method of endogenous fire risk assessment based on calorimetric tests of coal and developed mathematical model of the process of coal self-heating allow to predict the risk of spontaneous fires and select proper fire prevention measures adequate to the involved risk. The frequency of exogenous fires is in the last few years is low, but their share in the total number of fires is relatively high and constitutes about 30%. This results from the prevention activities, carried out regularly in mines which are aimed at reducing the fire hazard connected with the use of fire-resistant conveyor belts and other non-metallic materials. Further directions to reduce the hazards connected with underground fires should focus on improving the methods for monitoring hazards together with automation of fire fighting operations.

Aug 1, 2013

By J. Ga?parík

The optimal selection of machine or machine group for building processes is very important role of building planner during the process of building planning. During this process building planner have to analyze several factors influencing the final effective decision concerning this problem. There are several factors and criteria for effective selection of building machines. In our contribution there are analyzed: ability of machines to realize designed building process (quality aspect), duration of mechanized process (time aspect) and minimizing of energy consumption (cost and environmental aspect). Selected scientific methods and theories of problem solution can be divided into these groups: theory of system (creation of building machine selection method), multi-criteria optimizing method (analysis of mechanized building process from the point of more optimal criteria), queuing theory (application during the mathematical modeling of mechanized soil processes), method of scientific analysis (analysis of factors influencing final decisions), method of scientific synthesis (creation of optimizing method implemented into building processes and possible application in construction sector). Multi-criteria optimizing method were during our research work implemented into soil processes and selected building group machines (excavators and trucks), which are very often used in construction and mining processes. This method can be considered as a multi-level decision making process based on multiple parameters. In our contribution is presented key mathematical models for model example solution and software built in Java, which has been created as a support for method described in this contribution. Application of this method and software will increase the effectiveness of building machine selection from the point of key criteria of optimizing: quality, time and energy consumption.

Aug 1, 2013

By Silvio E. Kruger

Real time measurement of wear and corrosion provides crucial information needed to determine an optimal schedule for corrective maintenance and is a powerful tool to maximise equipment availability and reliability. It also leads to savings from optimized spare parts handling and helps to avoid costs of accidents and their negative impact on safety and the environment. This paper presents the technology of ?painted-on? ultrasonic transducers that can be integrated to structures and accurately measure the remaining thickness and therefore determine wear or corrosion losses. These transducers have a small footprint, a performance comparable to other commercially available ultrasonic transducers and can sustain temperatures as high as 400ºC. The application of this technology to mining equipments and its potential benefits are discussed.

Aug 1, 2013

By S. Aram

Product Lifecycle Management (PLM) solutions have been serving as the basis for collaborative product definition, manufacturing, and service management in many industries. They capture and provide access to product and process information and preserve integrity of information throughout the lifecycle of a product. Efficient growth in the role of Building Information Modeling (BIM) can benefit vastly from unifying solutions to acquire, manage and make use of information and processes from various project and enterprise level systems, selectively adapting functionality from PLM systems. However, there are important differences between PLM?s target industries and the Architecture, Engineering, and Construction (AEC) industry characteristics that require modification and tailoring of some aspects of current PLM technology. In this study we examine the fundamental PLM functionalities that create synergy with the BIM-enabled AEC industry. We propose a conceptual model for the information flow and integration between BIM and PLM systems. Finally, we explore the differences between the AEC industry and traditional scope of service for PLM solutions.

Aug 1, 2013