Search Documents

By Jihan Farhan Lubis, Putu Chandra Darmansyah

Ground vibration caused by blasting has become a common concern, especially when blasting is conducted near buildings or structures. Uncontrolled vibrations can potentially damage nearby infrastructure if appropriate control measures are not implemented. PT Tambang Semen SUKABUMI, a limestone mining company, is planning to carry out blasting activities near a crusher building located approximately 80 meters away. This building is classified as a Class 5 structure, with a maximum allowable Peak Particle Velocity (PPV) of 40 mm/s, in accordance with the Indonesian national standard SNI 7571:2023. To ensure compliance with this limit, a Signature Holes Analysis (SHA) was conducted using the Hanwha HEBS II electronic detonator initiation system. This analysis measured ground vibration from single-hole blasts, with the average vibration from three SHA holes recorded at 49 mm/s. A site constant analysis using the scaled distance formula yielded a multiple R value of 0.87. However, the ANOVA table showed a significance-F value of 0.24, which is greater than 0.05 indicating that the regression model used for prediction was not statistically significant. Using the SHA data and assuming a maximum of 30 blast holes, a recommended delay timing of 22 × 15 milliseconds was selected. This produced a predicted PPV of 17.25 mm/s. The comparison between predicted and actual PPV values demonstrates that the delay configuration derived from Signature Hole Analysis provides reliable results. The observed deviations range from -16% to +29%, with an average deviation of only 8%, indicating a high level of accuracy and consistency. Using the actual blast data, three model prediction were applied for predicting the most accurate prediction that close to the actual value. The SHA method, utilizing actual single-hole vibration measurements and optimized delay timing, provided the lowest average deviation of ±8% and the smallest absolute error (2.45 mm/s) from actual measurements, demonstrating high reliability for sites with sufficient signature data. Meanwhile, the log-log regression model yielded the highest coefficient of determination (R² = 0.751) and the smallest prediction deviation (3%) when standard deviation margins were considered, making it highly effective for predictive modeling.

Jan 26, 2026

By Matt Brandon

This case study demonstrates how integrating drone and GPS surveying with 3D modeling software creates more effective blast designs that address specific geotechnical challenges while improving safety and blast performance. In this case study an 80ft (25m) highwall experienced recurring slip plane failures exacerbated by a previously mined 40ft (12m) bench that removed back support, creating an unstable triangular rock mass. Previous blasting along this wall displaced the upper 40ft (12m) of material, opening geological discontinuities and causing progressive slope failures that compromised crew safety and blast effectiveness. High-resolution drone photogrammetry, GPS surveying, and laser measurements were employed to precisely map slip planes, bedding planes, and fault structures within the bench geometry. These geological features were imported into 3D design software to develop a shot pattern that strategically utilizes natural rock discontinuities rather than working against them. GPS-guided hole placement ensured accurate field implementation, while marking geological features on the surface of the bench provided visual references for the blast crew. The final blast design positioned the last row of holes to break preferentially along an existing slip plane while avoiding intersecting the next slip plane behind the blast. Explosive loading and timing sequences were adjusted based on the hole location relative to the 3D geological model to optimize fragmentation while maintaining wall stability. The optimized design improved highwall stability significantly, by reducing the slip plane failure mechanism that had previously compromised operations. Measurable improvements included enhanced highwall stability, reduced back-break, improved blast performance, and reduced safety risks for equipment operators and blast crews. Two subsequent shots using identical methodology were able to remove the rest of this problem area, confirming the repeatability and effectiveness of this integrated approach. This methodology demonstrates practical integration of surveying technologies with geological understanding to solve complex blasting challenges. Accurate 3D modeling of geological features enables blast designers to work with natural rock structures rather than against them, resulting in safer, more effective blasting practices. This case study shows the value of understanding the precise locations of geological features for optimizing blast design and provides a replicable process for addressing geotechnical challenges in blasting operations.

Jan 26, 2026

By Mattos J. L. C

Drilling and blasting with explosives in mining operations near communities require careful planning to mitigate socio-environmental impacts. Ground vibration, noise emission, flyrock, and dust dispersion are factors that may trigger conflicts with local populations. However, large-scale operations demand high productivity and intense material handling, making it essential to balance operational performance with impact control. The adoption of best practices, combined with advanced monitoring and mitigation technologies, enables sustainable mining even in proximity to inhabited areas. This study proposes the use of double and triple-deck blasting techniques with large-diameter boreholes (12 ¼” – 311 mm), addressing the sizing of charges and decks, as well as measures aimed at reducing noise perceived by nearby communities. The approach seeks to maintain the use of large drilling rigs already present in the operation, avoiding costs related to premature equipment replacement or expensive alternatives, while minimizing environmental and social impacts and promoting a more balanced and responsible mining model.

Jan 26, 2026

By Josh Calnan, Zach Agioutantis, Daykin Schnell

Damage complaints are a common occurrence related to blasting activities, specifically when blasting operations occur near residential areas. These complaints are often associated with ground vibrations from blasting. It is important for blasters and engineers to understand the potential for ground vibrations to damage residential structures to properly design blasts and appropriately address any damage complaints that arise. A review of the most recent studies of blast vibration damage thresholds for residential structures is conducted to provide a baseline understanding of blast damage potential and mechanisms. Gaps in research and understanding blast vibration damage potential are identified. Research in further understanding damage potential is presented and focuses on studying the impact of high-range ground vibrations generated from full-scale, nearfield ground vibrations from blasting on a residential structure. Specific impacts of the high-range ground vibrations reviewed as part of this research include damage to the block wall basement, global strain, rotational forces, crack generation, and crack extension in a residential structure. Planning and methodology for intentional full-scale, nearfield blasting at a limestone quarry within close proximity to a residential structure owned by the quarry are presented. Conclusions discuss the objectives and optimized layout of the ongoing data collection for the proposed research and analysis. Future potential work related to further understanding blast damage mechanisms and thresholds are also discussed.

Jan 26, 2026

By Paulo C. Fernández A, Sergio Matamala V, Claudio C. Gajardo, Christian A. Rees P

In fragmentation processes in open-pit mining, it has been observed that there are many opportunities for improvement if greater control of ore displacement in blasting is achieved, reducing the percentage of mixing between ore and waste material (dilution) through the integration of new technologies that allow its quantification and optimization of extraction polygons. This work investigates the relevance of the initiation sequence and direction of displacement in blasting in relation to ore dilution and the potential benefits of process optimization. A three-dimensional modeling tool was used to evaluate movement control optimizing the extraction zone based on the maximization of ore recovery. The study was made by iterating different scenarios, by varying only the initiation sequence and inter-hole delays. To validate the displacement simulation, a total of 10 blasts were carried out for calibration, obtaining a level of agreement between the simulation surface and the actual topographic survey of 80% or higher. The analysis included horizontal and vertical displacement, quantification of swell and dilution within extraction polygons for different scenarios, and informed decision-making based on ore control. The results clearly indicate that by modifying the blast initiation sequence, greater control over dilution in ore/waste transition areas is achieved, thus optimizing the recovery of the planned material and maximizing the ore grade. The use of this type of simulation tools allows for the generation of extraction strategies based on the value of the polygon, unnecessary displacements in the free face, optimal loading fronts, etc., maximizing the recovery of ore and stockpile material, complying with the planned tonnage and ore grade for each extraction polygon, delivering added value to the chain and emphasizing the importance of adding new technologies to the mining industry that allow for the optimization of processes to maximize profits.

Jan 26, 2026

By Erica Lorenzo García, Benjamín Cebrian Romo, Antonio Morato Medina

This paper presents the results of a preliminary study on blast-induced vibrations conducted at a Radioactive Waste Storage Facility, located in Spain. The study was undertaken as a preparatory step prior to the blasting operations required for the construction of a new platform located near critical infrastructure housing very-low, low and intermediate-level radioactive waste. The primary goal was to establish a site-specific vibration attenuation curve to safely determine allowable explosive charges based on their distance to sensitive structures. The study followed the criteria defined in the UNE 22.381-93 standard, which regulates permissible vibration levels for different structural typologies. In this case, the existing facilities were classified as Type III structures, given their heightened sensitivity to vibrations. Two experimental campaigns were conducted. Test 1 consisted of a series of 10 individual blasts with increasing charges, monitored by five strategically placed seismographs to record seismic wave propagation and determine the attenuation parameters via regression analysis. Test 2 simulated a production blast using operational charges of 41.7 kg (91.93 lb), applying different delay sequences (42 ms and 25 ms) between holes to assess wave interference, resonance, and constructive effects. Data analysis showed that the longitudinal component dominated vibration transmission, and the predominant frequencies in the most critical zone ranged between 18 and 20 Hz. Based on these values, a conservative peak particle velocity (PPV) limit of 4.75 mm/s (0.19 in/s) was established for blast design. The recorded vibration levels during the tests remained within regulatory limits, with maximum values of 2.35 mm/s (0.09 in/s) and 2.86 mm/s (0.11 in/s) for the sequenced blasts, and peak acceleration of 0.0464g.

Jan 26, 2026

By R. Jacob Cefalo, Miguel Valenzuela

The modern drill and blast engineer operates in an environment often rich with data from drilling data and blast designs vs. actuals to fragmentation distributions and vibration records. Despite this abundance, much of the information generated remains underutilized, often collected as a matter of routine rather than for a means to an end. This paper explores how artificial intelligence (AI) can bridge that gap, transforming raw operational information into actionable insights that lead to more consistent and optimized blasting outcomes. Through AI-driven analysis of drilling logs, burden and spacing measurements in design vs. actual, fragmentation distributions, and vibration records, we can identify hidden patterns and correlations that traditional analytics overlook or that we may not be aware of. These insights enable engineers to proactively adjust designs and loading strategies, ultimately improving performance aspects such as improving fragmentation, minimizing ground vibration, and lowering overall operational costs. The paper examines the industry's reliance on lagging indicators, such as post-blast fragmentation surveys or actual powder factors, and suggests the need to shift toward leading indicators like real-time drill data monitoring and predictive fragmentation modeling. Utilizing AI to forecast outcomes before a blast is carried out allows engineers to take corrective actions early in the process, thereby creating a feedback loop that continuously improves performance. This integration of AI into drilling and blasting practices marks a pivotal opportunity for the explosives engineering field to evolve from reactive to predictive methodologies unlocking a new level of operational intelligence and value creation.

Jan 26, 2026

By Piotr Mertuszka

Many years of research on more effective and safer explosives have led to the development of emulsion explosives. They are the second most commonly used group of explosives worldwide, primarily because they are good alternatives to ANFO or dynamites. Their key advantage in underground applications is the lower content of toxic fumes in the detonation products. Emulsions are also characterized by high detonation velocity, high water resistance, low critical diameter, and mechanical loading capacity. Several factors affect the behavior of emulsion explosives. These factors are related to both manufacturing and applied mining methods. The most important factors include the charge diameter, type of sensitizer, density, hydrostatic pressure, ambient and charge temperatures, as well as the time elapsed between the charging of the explosive into the blast hole and its detonation. The selection of the type of explosive is based on the analysis of a number of parameters, including the density, critical diameter, volume of the post-blast fumes, detonation pressure, velocity of detonation, and sensitivity to external energy sources. In most cases, the conditions under which explosives are used differ significantly from those defined in standards. Such conditions cover, among others, the temperature of the rock mass and surroundings, humidity, rock strength parameters and the diameter of the blast holes. Consequently, the parameters of the explosives provided by the manufacturers may not correlate with those specified in-situ. Thus, within the framework of this study, the effects of the selected technological parameters on the detonation velocity of bulk emulsion explosives are presented. The analysis focused primarily on the factors directly influenced by the mine blasting services. The detonation velocity measured using the continuous wire resistance technique was used as the evaluation criterion. For this purpose, several underground in-situ tests were conducted, including the impact of the blast hole diameter, density, initiation method, sleeping time, and temperature on the detonation velocity. The results of in-situ tests have shown that the detonation velocity of bulk emulsion explosives depends strongly on the above factors, which may directly affect the effectiveness of blasting operations.

Jan 26, 2026

By Aaron Nickoli, Brad Clark, Thomas Horan E. I. T.

The Canal Road Dip Slide is an active landslide located on South Pender Island, British Columbia. The effects of the fall 2021 atmospheric river prompted the British Columbia Ministry of Transportation and Infrastructure to initiate an emergency response project to realign Canal Road out of the active landslide zone for safe traffic passage. The work was tendered in a bidding process and included blasting and rock excavation work at the project site. Tetra Tech Canada Inc. was retained by the contractor to be their Blast and Vibration Specialist. The close proximities of an active landslide, a Canadian National Park, and other segments of construction posed stringent constraints to blasting. The governing constraints to blast design included a Peak Particle Velocity (PPV) limit of 3 mm/s (0.12 in/s) along the adjacent landslide centerline and a slide movement constraint. Sixteen blasts were executed throughout the scope of work to remove 2595 m3 (3394 yd3) of meta-sedimentary rock. Blast designs adhered to the constraints by utilizing up to quadruple decking in 50+ blast holes which lead to complex timing schemes. Several blasts were over 4 seconds in duration, with one at nearly 8 seconds. The landslide area was monitored with Shape Accel Arrays (SAA) throughout the scope of work that tracked geohazard slide movement during construction. The SAA data is presented, and the effect of blasting is discussed. Site specific parameters for PPV estimation were calculated and are presented. Collaboration and communication between the stakeholders allowed the project team to successfully overcome the technical challenges posed by the Canal Road Dip Slide.

Jan 26, 2026

By César Ugaz, Jorge Cardenas

Mitigating the vibrations resulting from a blasting rocks is one of the most common challenges that Peruvian mining has, since if this impact is not mitigated it can generate discomfort and altercations with neighboring communities and also puts the continuity of the mining project at risk. In that sense, we must establish control parameters to mitigate these effects as much as possible. As a starting point we must establish areas of interest that in this context would be the communities near the mine; first stage to carry out constant monitoring at these points, the registration of vibrations and noise is vital for the success of this control, with this information we can establish predictive models, the registration of elemental waves and the evaluation of human perception. In a second stage, this information allows us to make decisions in engineering such as the selection of delay times, elaboration of detonation sequence schemes, maximum amount of operating load per delay window, as well as the use of special load designs (Decks). There is a fear that these controls generate negative impacts to the process, referring to fragmentation, dig rate, throughput, etc. Since we limit the explosive load necessary for the results we need. To avoid this we use "Decks" type load designs under a sequencing between these under time calculations by elemental waves, which generate a reduction in vibrations up to 50%, also complying with strict regulations without affecting the power factors to comply with our performance indicators. Finally, in a third stage we must carry out a constant evaluation of results according to the progress of the mine.

Jan 26, 2026

By Gabriel Gonzalez, Paulo Couceiro, Luis Manriquez, Alejandro Gutierrez, Juan Navarro

A high-stakes blasting campaign was successfully executed at a major open pit copper mine in northern Chile. This operation posed a significant technical challenge due to its immediate proximity to the tailings dam - a critical infrastructure whose structural integrity depends on strict control of blast-induced seismic vibrations. The geological complexity of the area, characterized by upper andesite interbedded with caliche (carbonate), further complicated the operation. This lithological composition, known for its high tenacity and cohesion, posed additional challenges for achieving effective fragmentation, necessitating a highly customized blast design and loading strategy. The campaign included four production blasts and one secondary blast, all executed under the constraint of not exceeding the Peak Ground Acceleration (PGA) threshold of 0.64g, as defined by the Maximum Credible Earthquake (MCE) scenario. To ensure compliance, geophones were strategically installed at three monitoring points (P1, P2, and P3) on the dam to capture real-time acceleration data. The use of specialized blast patterns, precise stemming control, and electronically sequenced detonations ensured that all recorded accelerations remained well below the critical threshold. A total of 496,163 tonnes of material were safely blasted, with 8,452 meters drilled and powder factors ranging from 419 to 594 g/ton. Therefore, this case study exemplifies operational excellence in controlled blasting, demonstrating the feasibility of safe mining near geotechnically sensitive zones through predictive modeling, rigorous QA/QC, and post-blast analysis.

Jan 26, 2026

By TTE-Europe GmbH

A few years ago, the term Track & Trace for explosives was only known in Europe and Brazil at most; the introduction of this technology is experiencing an undreamt-of boom worldwide. More and more countries are enacting legislation to introduce Track & Trace of explosives and follow Europe and Brazil on this path. At present, the world's leading manufacturers are already using such solutions, are in the process of implementing them, or are in the planning process. However, based on the experience gained in Europe, there are outstanding challenges for all manufacturers. These are questions of compliance, logistics, distribution, and, of course, especially, the necessary adaptation of the production environment. However, this development involves considerable effort on the part of the manufacturers. New devices for marking the explosives and digitally recording the data are integrated into the production process. This should be done as cost-effectively as possible, without restricting production capacity and speed, and with as few process changes as possible. This paper uses real-life customer experiences examples to explain paths from project design to real implementation. Lessons learned from the experience of European explosives manufacturers are presented, missteps are described, and solutions are identified. Individual steps along this path are explained, and solutions are told to avoid pitfalls and bottlenecks. Finally, it refers to the risk analysis and concrete examples in implementing the planning into production. Methods of marking various explosives are shown, and the use of Track & Trace to solve logistics tasks in picking and shipping explosives, including the data exchange with ERP (Enterprise Resource Planning) systems.

Jan 26, 2026

By Andrew Palangio, Blessing Taiwo

Understanding rock mass structural features is essential for optimizing blast design, highwall control, and evaluating post-blast performance in both surface and underground mining operations. This paper presents a comprehensive methodology utilizing image-based structural mapping to accurately characterize geological discontinuities including joints, faults, and lineations captured from both terrestrial and aerial imagery at varying scales. Key structural parameters such as joint orientation, spacing, and apparent in-situ block size are extracted to understand rock mass classification and enhance blast design inputs with greater geotechnical precision. The study introduces a significant enhancement to the existing discontinuity assessment algorithm by integrating a deep learning-assisted detection process. This improvement enables more accurate, quantitative and consistent identification of pre-existing cracks and surface features across complex bench free faces. The enhanced system facilitates better evaluation of how structural features influence blast fragmentation, energy distribution, and slope stability. A case study from a limestone quarry illustrates the use of a derived comminution factor based on the relationship between joint-controlled pre-blast block sizes and post-blast fragmentation to evaluate blast performance and optimize future design strategies. The results highlight the value of structural analysis in reducing overbreak, minimizing underbreak, and improving fragmentation predictability. This paper emphasizes the importance of integrating structural assessments into the blasting workflow to enable a more data-driven, geotechnically informed, and performance-optimized approach to modern blast design and evaluation.

Jan 26, 2026

By Italo Onederra, Miguel Araos

Most of the current explosives for mining blasting activities rely on voids to become sensitive to initiation, then detonating and finally, sustaining that detonation. The use of voids is known as hot spot sensitisation. Various forms of voids serve as hot spots – gas bubbles (predominantly in bulk explosives), glass (or plastic microballoons, for packaged products), or expanded polystyrene (bulk explosives). Gas bubble sensitisation uses the decomposition of sodium nitrite to produce nitrogen gas bubbles, which are dispersed throughout the bulk explosion. These gas bubbles, when hit by a shock wave (such as from a booster), compress and heat up, subsequently decomposing the explosive and releasing energy to sustain the detonation. It has been suggested that the use of different types of gases to create voids in non-ideal explosives could offer some alternatives to the sensitisation process, which could be reflected in the change of the detonation properties of the explosive. The reason would be that each gas has a different ratio of specific heats (=/), and when these gas bubbles are compressed, they will heat up to different temperature, affecting the decomposition of the explosive and thus, the VOD.

Jan 26, 2026

By Evan Smart, Andrew Palangio, David Klingspor, Blessing Taiwo

This study presents a DMAIC-based approach to optimize blasting performance and achieve crusher-compatible fragmentation at the Walker-Severn Quarry in Ontario, Canada. By applying the Six Sigma DMAIC (Define, Measure, Analyze, Improve, Control) framework, the study aims to enhance the integration between blasting and primary crushing operations. Several representative blasts will be simulated and evaluated using both aerial and terrestrial image analysis technologies to assess fragmentation characteristics. The investigation was guided by quarry-specific Key Performance Indicators (KPIs), ensuring that blast design modifications were both practical and operationally relevant. Through structured analysis and data-driven refinement of blast parameters, the study reveals how this framework was used to address the quarry production demand for increased crusher throughput, and reduced processing costs. The existing quarry blast design was assessed as a baseline and compared against the crusher's inlet requirements and the acceptable fines level specified by the quarry. This evaluation aimed to identify and implement modifications to enhance blast performance. A drone (UAV) was employed to capture post-blast images and monitor blast pile displacement. These UAV images were used to generate an orthomosaic image, which was analyzed to assess fragmentation. The orthomosaic was overlaid onto a GIS platform using a 10m-by-10m grid to evaluate fragmentation distribution across the bench and identify areas requiring optimization. Additionally, drone imagery was utilized to monitor the impact of each blast on the subsequent blast's free face and to assess energy utilization for optimizing front-row holes to achieve improved fragmentation. The outcomes of this research offer a replicable methodology for continuous improvement in quarry blasting practices, with a focus on producing fragmentation that aligns with primary crusher requirements.

Jan 26, 2026

By Iván E, Alex Araya Jofre, Jean Guiroux Toro, Eduardo Valdés Guerra

Currently, it is important for companies to have controlled mining operations and adhere to production schedules. To achieve this, one of the key factors is maintaining high reliability in the P&T process, primarily the opening of ore stope, which could be delayed due to any unplanned or uncontrolled problem. These ore stope opening processes, whose main activity is generating free face, are a very important pillar for future mine planning. The possibility of ensuring their opening brings a series of downstream benefits: safety, economics, productivity, and compliance and adherence to plans. The process under discussion consists of developing free faces in a single blasting event. This will help us leverage greater reliability for overall production operation plans, reduce construction times, and open up opportunities for downstream improvements in the production process, considering technical factors in P&T designs. This study presents a developed methodology and shows the results of its implementation in ten (18) single-event free face blasts. The analysis includes cavity geometry, geology, rock qualities, drilling deviations, and the blasting strategy implemented for each event. The methodology used considered material fluffing processes, the actual drilling trajectory, the initiation sequence, QA/QC during explosive loading, monitoring instrumentation (vibrations), and VOD recording, among others. As a result, out of a total of 18 free-face events blasts in a single event, 16 were successful and two achieved 90% efficiency, reducing the stope's production start-up time by 50% compared to current operations. By implementing free face blasting in a single event, there are savings in operating costs, increased productivity of the mining equipment, and improved adherence to production plans. For applications with greater heights of free faces, where blasting cannot be carried out in a single event, we should consider performing them in two stages using wireless detonators already available on the market for mining operations.

Jan 26, 2026

By Hector O. Romero, Paulo C. Fernández A, Christian Rees Prado, Claudio C. Gajardo

In open-pit mining, estimating post blasting displacement and spillage accurately is essential to guarantee operational efficiency, ensure alignment with production plans and their associated key performance indicators. The absence of predictive modeling tools on blasting operations results in several critical challenges, including operational reworks due to deviations in material displacement, significant discrepancies between mine and plant (ore grade dilution included), misalignment with the reported production plan, and increased operational costs due to inefficient use of resources. This study, conducted at Los Bronces Mine operated by Angloamerican, Chile, addresses the application of a three-dimensional simulation tool that, through numerical modeling, is capable of predicting post blast rock displacement. The implementation was carried out in a pit phase characterized by blasts near the pit boundaries, with a high risk of material spillage and potential blockage of the only access ramp to the extraction levels. By the integration of key design parameters, such as blast pattern geometry, detonating time, explosive charge distribution and pre and post blast survey, an optimal calibration was achieved and validated in seven blasting events to date, reaching an accuracy greater than 80% in estimating post-blast rock displacement and spillage volumes. Furthermore, this study allowed the evaluation of different pattern alternatives with and without spillage mitigation measures (use of air decks near the free face), obtaining a high correlation and accuracy exceeding 95% in predicting the selected design outcome, supporting optimal design selections. The result highlights the usefulness of the model as a decision-support tool for blasting engineers and short-term planning, by reducing the need for unnecessary operational reworks, improving geological and operational reconciliation, and ensuring the alignment of the extracting plan with production targets. The current average deviation is 15%, with higher deviations observed in blasts with smaller volumes of spill or where the simulated sequence was changed before blasting. The use of this type of three-dimensional numerical modeling represents a significant advancement for blast engineering and the optimization of key performance indicators in open-pit mining operations.

Jan 26, 2026

By A. S. Romphf, C. K. McKenzie

Recent full-scale field studies involving single-hole charges fired to free faces under a wide range of operating conditions have delivered precious insights into airblast characteristics and propagation. The field tests involved production blasthole diameters in the range 89 to 406 mm (3 ½ to 16 in), bench heights in the range 9 to 24 metres (30 to 79 ft), burden ratios (burden/hole diameter) in the range 14 to 51, stemming ratios (stem height/hole diameter) in the range 11 to 36, explosive types of ANFO, heavy ANFO and pumped emulsion, and both solid-column and double-decked charge configurations. Around 700 measurements of peak amplitude and wave shape were made in all directions (0 to 360 deg) from the free face, from 38 single-hole tests in nine North American operating quarry/mine environments. The most striking observations were the strong dependence on directionality of the wave propagation parameters and wave frequency, the consistency of wave shape which resembled the modified Heelan wavelet, and the occasional appearance of distinct, multiple pulses from single events, shown to be echoes/reflections from quarry faces. In-hole deck charging failed in this study to achieve expected peak overpressure reductions, with the peak overpressure levels in Pascals/psi/millibars being approximately 40% higher than the as-charged weights. Inter-deck delay times in excess of around 25 ms are required for effective reduction of peak overpressure levels from front-row holes. Simple linear-superposition models based on synthetic wavelets applied to large production blasts produce composite waveforms which capture the important features of the actual pressure-time history, and correlate well with measured waveforms.

Jan 26, 2026

By Blenda Lopes, Rodolfo Matias, Vagner Paixão, Vinicius Leão VALE, Edivarde Sousa

Seismography is an extremely important subject in the context of rock blasting, especially in the current scenario, which involves the need for increased controls due to the growth of urban areas near open-pit mining operations. Worldwide, communities are becoming increasingly aware of the environmental and social impacts associated with mining activities. Therefore, maintaining good relationships with these stakeholders is essential to preserve the social license to operate and to comply with current legislation. This situation is exemplified in an open-pit iron mine near the capital of Minas Gerais, Brazil, where the community is located less than 40 meters from the pit boundaries. Blasting activities within the mining area occur at distances less than 500 meters from the nearest community, making continuous seismograph monitoring necessary to ensure that operational conditions are maintained without compromising exploitation efficiency. The threshold for peak particle velocity, according to Brazilian Standard 9653:2018 by ABNT, is 15 mm/s at frequencies around 4 Hz. However, even though the peak particle velocity commonly registered was inferior to 3 mm/s, there were still complaints from nearby residents regarding human discomfort. To further reduce vibration levels, a study was conducted to implement a new blast design, considering factors such as reducing bench height, altering the hole delays, maintaining the maximum charge per delay, and adjusting the drilling pattern without negatively affecting rock fragmentation quality. Following the implementation of the revised blasting parameters, seismographic measurements in the region decreased to below 0.6 mm/s. This significant reduction in ground vibrations contributed to minimizing community disturbances and fostering a more positive relationship between the company and its surrounding residents.

Jan 26, 2026

By Johan Hillman, D. Scott Scovira, Thomas Gustavsson, Alexander Bihlar

Hydrogen Peroxide Emulsion (HPE) explosives are an alternative to conventional commercial explosives. HPE does not contain nitrates or ammonia thus eliminating post-detonation NOx fumes and aqueous nitrate discharge. Production of HPE is less carbon intensive than industry standard ammonium nitrate-based emulsions (ANE) and employment aligns with end users seeking to meet Scope 3 ESG emission targets. Swedish tunneling contractor Implenia Sverige was awarded the Högdalen Depot Expansion Project by the City of Stockholm. Implenia Sverige partnered with Hypex Bio to be the first to pilot the application of a nitrate-free explosive system in a large-scale civil construction tunnel. The purpose of the joint project was to evaluate the operational suitability of replacing conventional nitrate-based bulk explosives with HPE in a large-scale tunnelling project. When the project commenced in September 2023 both standard nitrate-based emulsions and HPE emulsion were used in parallel (Tunnel Right and Tunnel Left) to enable operational, performance, and environmental comparison. Identical drill patterns and initiation techniques were applied to both tunnel headings. Performance data collected included round advance, usage, and perimeter quality. Implenia managed all drilling and charging operations and Hypex Bio provided technical support, including technicians and chemists. HPE is viscous and pumpable using conventional emulsion pumping delivery systems. Variable density functionality enabled loading different charge weights into cut, lifter, production, and perimeter holes. The primary rock type was hard sedimentary gneiss with approximately 150 MPa [21,755 psi] Uniaxial Compressive Strength (UCS). Fracture systems with infilling occurred in both tunnel directions. Rock quality factor was “Good to Very Good” on the RMRb (Rock Mass Rating) scale. Epiroc Boomer rigs were used to drill rounds averaging 4.9 m [16 ft] deep with high accuracy and precise reference positioning.

Jan 26, 2026