Search Documents

By Brajendra Mishra, Mark L. Strauss, Gerard P. Martins

Nearly the entire worldwide production of europium is recovered, as a minor constituent, from mining bastnäsite, monazite ore, or ion absorbing clays. However, this research indicates a process to recycle europium from waste lamp phosphors as a strategy meet the demand for europium. In this process, waste fluorescent lamp powder is retorted, sieved, leached, and precipitated to produce a mixed europium/yttrium rare earth oxide (REO). Europium is separated from yttrium by selectively reducing Eu(III) to Eu(II) using zinc powder and precipitating europium (II) sulfate from solution using sulfuric acid. Screening experiments were conducted observe the effect of pulp density, precipitation time, entrance pH, and stoichiometric ratio sulfate upon the grade and recovery of europium (II) sulfate. The best conditions to maximize grade and recovery of europium (II) sulfate were a 1 h precipitation time, 10 the stoichiometric ratio of sulfate, 100 g/L mixed REO, and the entrance pH equal to 3. The maximum grade of europium sulfate was 95.93%, and the maximum recovery was 73.32%.

Mar 1, 2018

By Liangying Wen, Zhehan Liao, Jian Xu, Chenguang Bai, Chengfeng Sun, Kaihui Ma, Yang Xu

The difference on particle density causes mass and size segregation in the blast furnace throat, causing poor permeability in radial and circumferential direction. Understanding the effect of density difference on particle spatial-temporal distribution helps stabilize smooth operation and improve energy ef ficiency of blast furnace iron-making process. Based on discrete element method simulation, the influence of density difference on particle segregation behaviors is quantitatively characterized by the proposed method when the binary-sized particles are charged from parallel-type hopper of blast furnace. The results show that increasing the 4 mm particle density aggravates the mass segregation in circumferential and radial direction, and the maximum standard deviation of each ring reaches as great as 0.415. For size segregation, the difference on average mass fraction of small particle between center and edge ring decreases from 0.373 to 0.301. When increasing the 6 mm particle density, the similar particle segregation behaviors could be obtained.

Mar 1, 2018

By Wei-Tong Du, Zheng-Lei Guo, Yu Wang, Shu-Chao Wang

The influence of bottom blowing a CO2–O2 mixture on the bath temperature of a vanadium extraction converter was studied by using the characteristics of CO2 with weak oxidizing. It was studied in two aspects: oxygen content and temperature. The experiments showed, when the ratio of the mixture of CO2–O2 was 2:8 at 1300 °C, the bottom blowing of the converter inhibited the heating up of the hot metal, thus keeping the temperature below the carbon vanadium transition temperature. At 1360 °C, the sensible heat absorption by CO2 was 1.44 times that absorbed by O2 per mole. Meanwhile, at 1300 °C, 20% CO2 released the chemical heat of 13.58 kJ. So with the increase of the CO2 ratio, the bath temperature was reduced. The research showed that the bottom blowing of a CO2–O2 mixture had an advantageous effect by decreasing the temperature of the vanadium extraction converter.

Mar 1, 2018

By Shaohua Ju, Feng Jiang, Jian Jian, Hongying Xia, Jinhui Peng, Libo Zhang

Microfluidic solvent extraction of zinc from sulfate solution was studied using di-2-ethyl hexyl phosphoric acid, D2EHPA, in sulfonated kerosene as diluent. The influence of different parameters on the extraction of zinc, such as flow rate, temperature, flow rate ratio, extraction concentration, and saponification ratio of extractant were investigated and the conventional and micro fluidic extraction were compared. Under the optimized conditions, micro fluidic extraction efficiency of zinc is up to 97.1%. It is better than that conventional extraction. Therefore, microfluidic solvent extraction can achieve high efficiency and low consumption of extraction process.

Mar 1, 2018

By Yijun Cao, Shengpeng Su, Guihong Han, Xiangyu Song, Yanfang Huang

Binder is indispensable in the production of iron ore pellets and the quality of pellets seems to be related to the interactions between binders and iron minerals. Humic acid is proved a suitable binder for iron ore pelletizing. In this paper, the interactions between humic acid and iron minerals were investigated by adsorption experiments and molecular dynamic simulations. Adsorption experi- mentalresultsshowthattheadsorptionofhumicacidonhematiteiseasierthanthat on magnetite, and the maximum adsorption capacities of humic acid on hematite and magnetite reach 17.1, 7.39 mg/g, respectively. The results of adsorption iso- therms indicate that the Langmuir model provides the best correlation of the experimental data, while the thermodynamics results demonstrate that the adsorp- tion process is a spontaneous exothermic process. Molecular dynamic simulations reveal that the interaction between hematite and humic acid is stronger than that between humic acid and magnetite. (cid:1) (cid:1) (cid:1)

Mar 1, 2018

By Duclerc Fernandes Parra, Vijaya Kumar Rangari, Washington Luiz Oliani, Ademar Benevolo Lugao, Nilton Lincopan

Due to its versatility and low cost, polypropylene (PP) is one of the most widely used polymers in the world, consequently in research and development of new products. The polypropylene modified was prepared by gamma irradiation in acetylene at 12.5 kGy dose, technical polymer also known as high-melt-strength-polypropylene (HMSPP). It was mixed with montmorillonite (MMT) clay and silver nanoparticles (AgNPs) for bactericide activity. HMS-Polypropylene-clay-silver nanocomposites were manufactured using twin-screw extruders. Those materials were prepared by a melt mixing process via twin screw extrusion with a wide range of processing conditions. The polypropylene nanocomposites (PPNC) surfaces were exposed to gamma-radiation (60Co) source in presence of nitrogen as inert atmosphere at 1; 3; 5; 10; 20 and 50 kGy doses for modified the surfaces in order to enhance biocide activity. The samples surfaces were characterized by Differential Scanning Calorimetry (DSC), X-ray Diffraction (XRD), Thermogravimetric Analysis (TGA), Scanning Electron Microscopy (SEM), Energy Dispersive Spectroscopy (EDX) and evaluated by determination of bactericide effects. The results indicate the formation of structures predominantly intercalated of HMSPP nanocomposite. Contact tests for antibacterial activity of the hybrid polymer were applied against Escherichia coli (Gram-negative) and Staphylococcus aureus (Gram-positive) bacteria. The irradiations on the samples surfaces were insufficient to promote activity on contact biocide tests.

Mar 1, 2018

By Neale R. Neelameggham, Brian R. Davis

Organic agriculture is using natural materials such as degrading plant matter to replenish soils. This includes use of naturally degraded plant components such as peat, humus and weathered brown coals. Another important natural organic matter which has not been applied in agriculture thus far has been the black coal, Here we show that reversing the coal formation reaction by combined hydro-oxidation principles of biochemical engineering in natural conversion methods in an accelerated fashion. The modified coal soil additive can convert arid lands into farm lands for the future to sustain the population growth. In addition, the development of this new use of black coal will revive economically deprived areas from phasing out coal in the USA and Europe. This will show how the Stored energy in coal can be made renewable in helping plant growth under the soil to facilitate above ground photosynthesis.

Mar 1, 2018

By Z. Jing, C. Jun

High-purity Bi2O3 was prepared via extraction-preparation stripping method use BiCl3 leaching solution. Parameters such as oxalic acid concentration, phase ration, aging duration, feeding duration, were examined for their effect on the size and morphology of precipitate. The precipitate was characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM), particle size analysis, differential scanning calorimetry and thermal gravity analysis (DSC-TGA) and infrared spectroscopy analysis (FT-IR). Bi2O3 was characterized by elements analysis, particle size analysis and scanning electron microscopy (SEM). Bi2O3 product of 680 nm was obtained using 15 g/L oxalic acid, 1/1 phase ration, 0 min aging duration, 0 min feeding duration and calcinating at 500 °C for 2 h.

Mar 1, 2018

By Camille Fleuriault

Continuous development of lead recycling technologies has driven the increasing contribution of secondary lead in battery manufacturing over the years. This review presents and compares the different technologies available for pyrometallurgical processing of secondary lead materials. Smelting is most often achieved in reverberatory, blast, rotary or electric arc furnaces, using single or two stage routes. Thermal re fining is the most common technique used for the production of lead and its alloys. Some improvements in battery breaking technologies and emission control have also specifically contributed to improve the performance of the smelting and refining units. Recycling lead is facing the challenge of increasing production while meeting more and more stringent regulations. This review will also include an analysis of the current secondary lead market as well as an economic outlook for the years to come in regards to rapidly changing environmental standards.

Mar 1, 2018

By O. M. Popoola, A. P. I. Popoola, D. O. Okanigbe, A. A. Adeleke

The physical, chemical, mineralogical and morphological characteristic of the waste copper smelter dust (CSD) from Palabora Copper (PTY), Limpopo, South Africa, has been reported in the open literature. The bulk of this material falls within the −53 μm particle size fraction with a copper weight percent of 18.02 as determined with the XRF. The high presence of reactive gangue minerals such as mullite (42.97 wt%) and quartz (11.45 wt%) necessitates that the waste CSD be first upgraded of its copper value in the falcon gravity concentrator before subsequent hydrometallurgical treatment. As an initial step, a sample preparation was carried out to make the sample amenable to both real density determination and copper upgrade experiment, thus resulting in 97% of the particles passing the 300 μm sieve aperture (d97 = 300). The laser particle size analyzer (LPSA) was used to analyze the d97 = 300 and the results showed a %change from 90.82% to 95.59%, with a real density of 2.830 for the waste CSD. The result of the copper upgrade showed that test 8 with treatment combination of 80 rpm and 4.5 l/min gave the highest % copper grade of 1.37 which is still less than the %grade of copper in the feed (1.49%). It thus lead to the recommendation that another type of centrifugal separator that will allow the introduction of the feed as slurry so that the pulp density and feed rate can factored into the whole upgrade experiment, consequently reducing the significant amount of losses and the chances of an improved grade and recovery of copper from this waste CSD.

Mar 1, 2018

By Yuya Nakai, Kuniaki Murase, Kazuhiro Fukami, Atsushi Kitada, Ken Adachi

The resources of vanadium –titanium magnetite in China are very abundant, most of which are used to prepare titanium-rich materials. Titanium pigment, electric welding bar and titanium sponge are made from titanium-rich materials such as synthetic rutile and titanium slag etc. To fully utilize titanium resources, many production methods of titanium-rich materials were proposed. In this article, authors review on methods of preparing titanium-rich materials which are Electric Smelting Process, Reduction-rust Process, Selective Chlorination Process, Acid Leaching Process, and sum the advantages and disadvantages of them. Existing problems and possible tendency of production methods of titanium-rich materials are also discussed.

Mar 1, 2018

By Haibin Wang, Kaile Tang, Chenn Q. Zhou, Guangwu Tang, Zhixiang Cui, Ping Zhou, Armin K. Silaen, Hongjie Yan, Zhi Wang

The submerged lance smelting furnace (SLS) for copper smelting has been developed and used by Dongying Fangyuan Nonferrous Metals Co., Ltd. The technology has shown advantages such as high oxygen enrichment, good feed adaptability, short processing time, high SO2 concentration for acid plant, and auto-thermal operation. In this study, computational fluid dynamics (CFD) was used to investigate the gas/matte two-phase flow characteristics and the chemical reactions in the SLS during typical operational conditions. The Eulerian-Eulerian approach was employed to model the phase interactions. The chemical reactions were modeled by calculating the mass transfer coef ficients and using the eddy-dissipation model. The simulation was conducted using the commercial software ANSYS Fluent®. The developed CFD model is able to predict the flow, temperature, and species distributions inside the SLS under various operating conditions.

Mar 1, 2018

By Qingyun Huang, Wei Lv, Junyi Xiang, Xuewei Lv, Chenguang Bai

The roasting is the key step for the extraction of vanadium from vanadium slag by calcification roasting–acid leaching process. In this study, thermogravimetric analysis and kinetic study of vanadium slag in the presence of calcium oxide was investigated. The maximum oxidation degree was slightly increased by increasing temperature from 700 to 900 °C then almost unchanged further increasing temperature to 1000 °C. The reaction mechanism was analyzed through both Sharp method and ln-ln method. Results showed that the mechanism the reaction in the a range of 0.1–0.8 corresponded to the random nucleation and subsequent growth, as represented as (G( a)=[ −ln(1−a)] 1/3 = kt. The apparent activation energy was calculated to be 3.5 kJ/mol according to Arrhenius equation.

Mar 1, 2018

By Jianhua Xin, Min Chen, Jin Xu, Hui Li, Nan Wang, Ming Chen

The kinetics study of blast furnace dust (BFD) recycling with flash reduction process at high temperature has been carried out using a high temperature drop tube furnace in laboratory scale. A combination characterization methods of chemical titration and SEM-EDS were used to track the reduction kinetics. The experiments using CO and CO2 mixtures with range of CO/CO2 (1:0, 1:1) at different temperature (1623–1723 K) and at different reduction time (1560– 2340 ms) were conducted. It was found that the reduction degree increases with the increase of temperature and reduction time as well as CO concentration. The carbon contained in the original BFD has weak in fluence on the reduction potential in the form of gasification. The unreacted core model was adopted based on the observation of the cross section and the measurement of iron element content, the effective diffusion coef ficient and reaction rate constant were determined and the rate controlling step was also analyzed.

Mar 1, 2018

By C. G. Bastos Andrade, F. R. Valenzuela Diaz, S. M. Toffoli

The climate change observed in the last decades, the increase of global warming, the melting of the polar ice caps, and the sea level rise have in common the non-sustainable development as causative agent. Different nations have mobilized joint efforts with the objectives of minimizing the impact of greenhouse gas (GHG) emissions, investing in the research and the development of new technologies in recycling, in biomaterials, environmentally friendly processes, and new fuel alternatives. This paper evaluates the efficiency of a Brazilian bentonite modified by acid attack, in the purification step of a waste oil to be used for biofuel production, that is, diesel from waste cooking oil (WCO). The following characterization test swere performed: XRD, CEC, XRF, SEM/EDS, specific surface area (BET), stereomicrography, kinematic viscosity, and spectrophotometry at 440 nm. The modified bentonite exhibited good purification capacity for WCO when compared to a commercial product.

Mar 1, 2018

By Kai Hu, Xuewei Lv, Run Zhang

An oxygen sensor of zirconia-based solid electrolytes for in situ measurements of oxygen potential in high titanium slag was developed in the present study. With the facility, series of measurements of electromotive force were successfully conducted for different titanium slags at 1998 K under an argon atmosphere. Oxygen potential in the slag was calculated by the measured EMF and simultaneous readings of temperature using the modified Nernst equation. In addition, the relationship between slag compositions and the oxygen potential in the slag was explored in detail. It has been found that the oxygen potential increases with increasing FeO content in the slag and decreases with the increasing Ti2O3 content in the slag. The oxygen potential in the slag has been calculated thermodynamically and compared with the experimental measurements. The results showed that oxygen potential in the slag may be controlled by FeO/Fe equilibrium reaction.

Mar 1, 2018

By Sudha Goel, Manis Kumar Jha, Deblina Dutta, Rekha Panda

Based on the placement of lead and its consumption in industry bran- ches, the paper deals with the composition of lead in the massive of Kopaonik. Removal, tenuity and grinding of galenit. The paper in particular treats the flotation process, and also treats physico-chemical bases of reagents in the process, as well as decanting, drying, filtering and storage of concentrates. Veri fication of the chemical composition of Pb concentrates with Pb, Zn, Bi, As, Sb, In, Au, Ag, etc. It is special that in Kopaonik massive the ratio of Pb: Zn composition is 1.4:1.0 and during the flotation lead is inclined to go with pirotines concentrate more than is allowed. We are strongly focused to maximally decrease the Pb amount that goes with pirotine concentrates and wastes. The paper as such gave the first effects in optimizing of these parameters with positive effects in flotation process in Trepca.

Mar 1, 2018

By Ying Wang, Min Chen, Cuihuan Huang, Haohua Deng, Nan Wang, Ming Chen

Adding limestone directly into converter is considered to be favorable to energy conservation and emission reduction by transferring the decomposition reaction of limestone from the shaft or rotary kiln to the converter. In this paper, the kinetics of limestone decomposing in early converter slag was studied at 1300–1400 °C, and the effects of slag temperature and stirring speed introduced to the slag bath were examined. The kinetic results based on shrinking core model analysis showed that the limestone decomposition was a mixed rate control of chemical reaction and heat conduction through the lime layer, which could be promoted at higher slag temperature by supplying more heat to the converter bath. In addition, the chemical reaction rate constant and effective thermal conductivity were determined.

Mar 1, 2018

By Chonghe Li, Pengyue Gao, Xionggang Lu, Juyun Kang, Wajid Ali, Guangyao Chen, Ziwei Qin

A refractory U–Mo associated ore containing jordisite which enclose U, Mo component, and impede penetration, diffusion process of leaching, oxidation agent was investigated through three approaches of focusing on U, Mo extraction. The results indicate flotation beneficiation without followed metallurgical process is not appropriate because of high target metals loss rate via water leaching. H2SO4, H2O2 dosage recommended to oxidation leaching are 10 and 6–8% of ore mass, and U, Mo leaching rate are 92.71 and 52.16% respectively. For the acid pressure leaching, U, Mo leaching rate 93.75 and 76.07% are achieved under optimal temperature 130–140 °C and H2O2 dosage 8% combined with pressure air 0.6 MPa. Fluidized bed furnace roasting parameters include air flow rate 0.64 m/s, air ore ratio 0.3 m 3/kg at roasting temperature 550 °C with U, Mo leaching rate 93.2 and 89.5%, so enhanced metallurgical process effectively destroy wrapper and increase metal recovery rate.

Mar 1, 2018

By Onuralp Yucel, Ahmet Turan, K. Can Candeger

Exothermic riser sleeves are important tools to increase solidification duration, particularly for iron-steel casting. Increasing the time to solidus improved casting product quality by minimizing cavities. Therefore, process costs were significantly reduced. In comparison with the use of unsleeved risers, exothermic riser sleeves retain up to 30–35% of the heat and increase the duration to solidus by nearly 50%. Exothermic riser sleeves are a mixture of metallothermic-based exothermic and insulating materials that are manufactured in different sizes and shapes. Various suppliers produce these sleeves in different compositions. However, the designers must clearly understand the thermochemical and thermophysical properties. The purpose of the present study was to experimentally determine the effects of varying experimental parameters such as reaction duration, flammability and temperature change etc. on selected exothermic sleeves. The results were compared with thermodynamical simulations which were performed using the contents and the corresponding thermophysical properties of exothermic sleeves.

Mar 1, 2018