Search Documents

By Tarrant GC

Cement and resin encapsulated tendons are widely used in the stabilisation of mine roadways. One of the main factors in controlling the efficiency of the reinforcement is the ability of the tendon to generate load in response to rock deformation. The analysis of field data from instrumented reinforcing tendons complimented with extensive laboratory investigations have more accurately defined the mechanisms by which load generation occurs. The role of reinforcing tendon profiles, hole geometry and encapsulation medium properties in controlling the reinforcement stiffness and capacity are discussed. The results of the investigation have implications in both the design of rock reinforcing systems and the optimisation of encapsulation mediums and tendons.

Jan 1, 1992

By Mark C

Designing coal pillars to provide resistance against overburden loads has long been an aim of rock mechanics engineers. The need for accurate pillar strength models has become.more urgent as greater overburdens are encountered and pillar sizes grow larger. Current pillar design models differ widely in their predictions of the trend in pillar strength with increasing pillar width- to-height ratio. The goal of this paper is to evaluate current pillar strength theories, using a comprehensive data base of stress measurements from coal pillars. The stress measurements indicate that coal pillars maintain relatively high stresses near the ribline, and that the stress gradient within the yield zone can be approximated as a straight line. Several problems are identified for further research, including calibration procedures for different types of stress cells, strain softening behavior in the yield zone, and measurement of stresses in the cores of very wide pillars.

Jan 1, 1992

By R. J. Good

It is well known that the elimination of impurities such as iron pyrite, shale, clay, silica, etc., from coal, by floatation [Sun, 1954; Aplan, 1983] and selective oil agglomeration [Keller and Burry; 1990] depends on the fact that coal is hydrophobic, and the impurities are hydrophilic. The water contact angle has long been used to evaluate the hydrophobic nature of coal, first by Brady and Gauger (1940), who demonstrated that the contact angle of water on coals increases with rank, and passes through a maximum at about 88% carbon. Brown (1962) found that the contact angle of coal decreased with increasing ash content. Sun, and also Aplan, have reported a direct relationship between values of the contact angle and rank, and have related the contact angle to coal floatability. Horsley and Smith (1951) first demonstrated that the captive bubble contact angle may be used to characterize the hydrophobicity of a coal containing more than 80% carbon DAF, while Parekh and Aplan (1978) have shown that the sessile-drop technique may be used to evaluate the hydrophobicity of coal of any rank.

Jan 1, 1992

By A. J. S. Spearingt

The hydraulic transportation of relatively dense slurries for backfill purposes is typically carried through vertical and horizontal pipelines under gravity. Wear in backfill pipelines has become such a major problem that it is now one of the main reasons for the relatively slow build-up of placed backfill in spite of encouraging performance results in the gold-mining industry. This paper describes tests on pipeline wear that were carried out on classified tailings from the backfill plant at Vaal Reefs East. The testwork was carried out under various conditions of slurry relative density, slurry velocity, and pipeline diameter. Empirical relationships are presented for each transportation and pipeline parameter evaluated and, finally, overall relationships between pipeline conditions and transportation parameters are proposed.

Jan 1, 1992

By Cadman S. J

( The central part of the Gippsland Basin is surrounded by existing major Petroleum accumulations and although six exploration wells have been drilled in the area, none are significant petroleum discoveries. Post drilling analyses indicate that the wells were drilled off structure due to the presence of high-velocity Miocene channels. These channels contain carbonates of significantly higher interval velocity than the surrounding sediments. Problems with seismic interpretation were thus encountered in the development of prospects in the central part of the Gippsland Basin as part of a BMR prospectivity study. The seismic interpretation problems associated with the Miocene channels are two-way time pull-ups at the underlying top of Latrobe Group and deeper levels on the seismic sections. Interpreted seismic sections passing through some of the exploration wells and the Miocene channels are presented to illustrate the configurations of these channels and the pullup effect associated with them. Two different methods of depth conversion were applied, one for the area below the high velocity channels and the other for the area away from the channel. The application of these two methods of depth conversion were found to be reasonably successful in correcting for the pull-ups caused by the high velocity Miocene channels. Mapping of the events near the top of Latrobe Group and near Base Lower L balmei seismic horizons has led to the identification of several potential structural closures. Further exploration efforts are necessary in this area to test these closures.

Jan 1, 1992

By J. Iannicelli

Kaolin, normally an inert filler when compounded with polymers, is converted into a strongly reinforcing pigment by prereaction with certain functional silanes. Modification of kaolin with amino and mercaptosilanes allows it to form crosslinks and confers significant improvements in modulus, abrasion resistance, compression set and other physical properties of a broad range of polymers.

Jan 1, 1992

The Olympic Dam Mining Operation involves the supply of some 2.2 million tonnes per annum of ore feed for the metallurgical plant. To achieve this approximately 9 km of tunnels are developed per year to gain access to the long hole open stopes that supply the majority of the production tonnes.Vast amounts of data are produced in the mining activity from the geology, mine design, scheduling, surveying, shift reporting through to the statistical reporting and analysis of the performance of the mine activities. Care must be taken when obtaining the data to maximise the usefulness of the data to other users so not to impose constraints or additional processes on future users.

Jan 1, 1992

By Terry Matts, Henry Heidrich, Cluny Randell, Carl Kottmeier

Until 1990, all production of asbestos ore at Cassiar was by open-pit methods. With the impending exhaustion of open-pit reserves, a decision was made in February 1988 to continue mining underground, using the block-caving technique.

Jan 1, 1992

The first Mine Rescue Performance Evaluation for mine rescue teams was held just prior to the 1992 RMCMI convention meeting schedule on June 27 and 28. Six teams took part in this year's evaluation; Decker Coal, Decker, Montana; BHP Minerals' White Team and BHP Minerals' Purple Team, both of Aztec, New Mexico; Kerr McGee Coal Corporation, Jacob's Ranch Mine, Gillette, Wyoming; The Coteau Properties Company, Freedom Mine, Beulah, North Dakota and The Falkirk Mining Company, Falkirk Mine, Underwood, North Dakota. This was the first mine rescue evaluation program developed to measure a unit's proficiency in their skills rather than emphasis on a ranking order of teams. The objectives for the evaluation were to promote learning and to evaluate the current level of experience of the attending rescue units. The priority goal for this evaluation was to recognize current rescue skills, knowledge and abilities of each team participating. In doing this, each team is provided with individual evaluations and a path for improvement as needed. [ ] Realistic industrial related scenarios, closely simulating the stress of actual rescue incidents, was provided by members of the Hermosa Cliffs Colorado Fire Department under the direction of Dan Noonan, Fire Chief. On Saturday, June 27, five rescue scenarios were presented for each team to complete and on Sunday three of a more difficult nature were encountered by each team. On the final day of the RMCMI convention two of the teams performed rescue demonstra¬tions. Onlookers were afforded the opportunity to view the teams in action as they simulated actual rescue operations. The value and importance of mine rescue teams such as those participating in this year's Rescue Team Performance Evaluation are very evident as in many cases they are the only rescue personnel and medical staff on the work site in case of an emergency. Most of these persons are volunteers who spend many hours studying, practicing and perfecting their expertise in the lifesaving techniques needed in the event of a mine emergency. At the same time, they are very qualified coal miners who perform their respective duties at their mine locations, Their dedication to gaining the most knowledge they can get to handle these life and death situations is evident in their participation in evaluations such as this one. [ ] If a highly educational, informative, sharing of knowledge and expertise, while at the same time providing a very enjoyable experience, deems this evaluation a success ... the Rescue Team Performance Evaluation held during the RMCMI Convention at Tamarron this year was certainly a SUCCESS!! It is hoped that you can all enjoy this same experience with us next year! Linda G. Ash The Falkirk Mining Company [ ]

Jan 1, 1992

By L. A. Puchkov

Problems of how to use artificial intelligence (AI) methods and expert systems (ES) to control complex industrial projects have lately become significant in practical terms. Mining ventilation systems undoubtedly belong to complex multi dimensional objects of control with stochastic nonstationary and nonlinear processes. Formal models based on automated ventilation control, do require awkward algorithmic solutions, moreover, a number of tasks become the operator's headache, and the quality of their solution depends on his experience and intuition. These tasks include: - identifying pre-accidental situations and determining their causes; - making well-grounded decisions with regard to changing ventilation regimes, forecast of mining operations taken account of; - controlling ventilation systems in emergency situations, e.g. when in accident, etc. It is in this context that we have for a number of years been investigating how to practically use AI methods for operative control in dynamic aero-and-gas mining processes, one of our research directions being devoted to working out a consulting programme for the ventilation system operator. Our researching and modeling problem was identification of aero-and-gas situation in different parts of ventilation network and its interpretation in order to determine possible causes for gas regime changing and unexpected consequences. We would single out the following stages in this task: I. Operative information procession coming to the data base from the sensors and analysis of hypothetical versions (using the associative rules base) with regard to factors which have caused significant parameter fluctuations (e.g. C%(t), H(t), Q(t) etc.)., 2. Selection of hypotheses in the knowledge base and forming conclusions in accordance with reliability scale. 3. Clarifying the obtained conclusions in dialogue with the operator. 4. Correcting the associative rules base.

Jan 1, 1992

By R. K. Mehta, C. W. Schultz, J. B. Bates

Introduction The Mineral Resources Institute, The University of Alabama, has for the past three years been engaged in a program to develop a beneficiation system for eastern (Devonian) oil shales. One objective of that program was to evaluate advanced technologies for effecting a kerogen-mineral matter separation. Column flotation was among the advanced technologies selected for evaluation. Early in the program it was shown that column flotation was superior to conventional (mechanical) flotation and to the other advanced technologies being evaluated. The investigation then proceeded toward the further objective of defining the optimum operating conditions for column flotation. One observation made in the course of optimization testing was that introducing the feed into the froth (above the pulp-froth interface) resulted in an improved combination of concentrate grade and kerogen recovery. This observation was reported in a previous paper (Schultz and Bates, 1989). Because the practice of maintaining the pulp froth interface below the feed point is contrary to "conventional" practice, it was decided to subject the observation to a systematic series of tests. This paper describes a recent series of tests and the results that were obtained. Experimental equipment and procedure The arrangement of the column cell and auxiliary equipment for continuous flow testing is shown schematically in Fig. 1. The feed sump [O] is filled with a sufficient volume of prepared sample to permit a large number of tests to be performed (typically 12). Past experience has shown this is necessary to control sample variability and variability in the size distribution resulting from ultra fine grinding. The feed slurry is maintained at about 20% solids and is constantly recirculated and stirred. The sample is metered from the circulating pipe by a peristaltic pump [O]. The feed slurry is diluted with reagentized water [O] by a second peristaltic pump [O]. Wash water [O], also reagentized, is supplied through a third peristaltic pump [O]. While this feed system may seem unduly complex, it does permit users to independently vary either the wash water rate or the net solids content of the cell. In the tests reported here, the feed rate and net percent solids were constant at 12.5 gms/min. and 3.3%, respectively. Diluted feed enters the column through 6.35 mm-diam (0.25 in.-diam) copper tubing and is discharged upwardly at the center of the column. Tailings are discharged through flexible tubing that can be adjusted so as to control the position of the pulp-froth interface. The column is 76.2 mm-internal-diam (3 in.-internal-diam) and 1090 mm (43 in.) high. It is made from lucite tubing and is fitted with a 51-mm-diam (2-in.-diam) fritted glass air sparger having an average pore diameter of 50 µm. In performing a series of tests, the concentrate and tailing are allowed to discharge continuously. The system is allowed to equilibrate for 30 minutes after the pulp and froth reach operating levels. Concentrate and tailing samples are taken simultaneously for timed intervals (five to 15 minutes, depending on the volume of sample desired). After sampling, a change in operating conditions is made and the system is again allowed to equilibrate. The tests to determine the effect of the pulp-froth interface level were part of a larger series of tests in which the objective was to optimize the conditions for a rougher flotation stage in a two stage circuit. The sample used in this series of tests was an Alabama shale ground to d90 = 23.1 µm and d50 = 7.9 µm. The operating conditions remaining constant in this series of tests were as follows: Column height - 1600 mm (63 in.) Air sparser - 50 µm (average pore diameter) Spray water - 130 cc/min. Feed rate - 12.5 gm/min (0.4 oz per min) (dry solids) Percent solids - 3.3% Frother (Dowfroth 250) - 45 ppm The variable test conditions are tabulated in Table 1. Positions of the pulp level (pulp froth interface) and feed entry are presented as a percentage of column height (as measured from the face of the air sparser). These test conditions are presented Fig. 2. At each of these test conditions, individual tests were performed at varying air

Jan 1, 1992

By D. W. Fuerstenau, G. S. Sudhir, P. C. Kapur

Quartz-limestone feed mixtures were ground in a laboratory-size, choke-fed, high- pressure roll mill. As compared to individually ground minerals, the harder component (quartz) in the product mixture is coarser, and the softer component (limestone) is finer. An energy split index is introduced for quantifying the disproportionate split of the mill energy between the feed constituents. This index is incorporated into a grinding kinetic model for simulation of the product size distributions of the mineral components as a function of energy input to the mill. The self-similar character of the size distributions is analyzed and an energy-size reduction relationship for the roll mill is highlighted.

Jan 1, 1992

By R. R. Irrinki

Abstract -The Key Anacon deposit consists of four sulfide zones called, from south to north : Key Anacon No. 1, Key Anacon No. 2, Key Anacon No. 3, and Key Anacon Copper Zone. Massive sulfides of zones 1, 2, and 3 are underlain by rocks correlated with the Nepisiguit Falls Formation and are overlain by matie volcanic rocks correlative with the Boucher Brook Formation. In contrast to zones 1, 2, and 3, narrow northwesterly-trend.ing, copper-rich fracture zones occur within the Patrick Brook Formation. Sulfides in zone 2 occur as three mineralogical associations, namely: pyrite-chalcopyrite, pyrite-sphalerite-galerta, and pyrrhotite-sphalerite-galerta. The distribution of lithologies and en-echelon patterns of the three sulfide lenses of Key Anacon No. 2 zone are the result of F1 and F2 folding. Zone 2 is the most promising economically, with proven reserves of 1.11 million tonnes grading 0.2207o Cu, 3.47% Pb, 8.41% Zn, and 96 g/t Ag; the zone is open below a depth of 427 m.

Jan 1, 1992

By Richard H. T. Garnett

Diamonds were discovered on the coast of Namibia in 1907 but it was not until 1962 that the first gems were produced from offshore by a barge employing an airlift. Geophysical surveys and a sampling program were initiated and an understanding of the diamond distribution was gained. Several vessels, some with multiple airlifts, were used until the early 1970's. Some spectacular production results were achieved, but generally the systems failed to retrieve the gravels efficiently from beneath the overburden and off the bedrock. Various companies continued working with mixed outcomes until the mid-1980's, when new regulations were enacted by the authorities. The local Southern sea conditions dictate the present mining methods which are now applied over several hundred kilometers of the west coast. In shallow waters divers operate from small vessels, suctioning the diamondiferous gravels to surface with gravel pumps. In water depths of up to 50 m airlifts of various designs continue to be utilized with recovery plants installed on the vessels. Beyond 100 m depths a remote controlled, tracked, vehicle is used, together with a large drill mounted on swell compensator. Each system is deployed from a separate ocean-going vessel. Production of diamonds from the offshore is rising rapidly, with expectations of further increases. The coastline is likely to be the scene of new developments in marine mining techniques.

Jan 1, 1992

By Juan J. Campo

The Freeport-McMoRan Main Pass Mine development in the Gulf of Mexico is a complex designed to extract up to 67 million long tons of sulphur over a 40 year period. The initial development includes 15 platforms and 13 bridges located in water depths ranging from 208 to 214 feet, approximately 15 miles east of the Mississippi River Delta. Three additional platforms were designed and installed for the oil and gas development in the complex. Over 110, 000 short tons of steel were required to fabricate the structures. As the sulphur is extracted significant subsidence is predicted over a major portion of complex in the shape of a very large bowl. Vertical elevations are predicted to change as much as 65 feet. Horizontal movements and mudline slope changes cause adjacent platform decks to move as much as 30 feet relative to each other. Differential soil movement is predicted between piling of individual platforms causing the piling to spread, resulting in significant lateral loading on the piling. Relative vertical soil movements are predicted along the lengths of the piles which causes "up drag" or "down drag" forces on individual piles. This paper addresses the design of the piling for the structures in the complex. Design criteria will be discussed explaining how the more traditional offshore environmental and gravity loadings were combined with the unique loading caused by subsidence. Design and analysis procedures will be explained and analysis results presented. These results include the incorporation of 100 ksi steel in thicknesses up to 5 inches in some of the tubular piles. Comparisons will be made between conventional offshore structures and these structures designed to accommodate the subsidence.

Jan 1, 1992

By W. Petruk

Mineral liberations that would be obtained by grinding an ore to a specific size can be predicted by analyzing unbroken ore pieces, and mineral liberations in ground ores and mill products can be determined directly by image analysis. Predictions of mineral liberations are made by measuring size distributions and textures of mineral grains by image analysis and using liberation models. Ground ores and mill products are analyzed to determine the proportion of mineral that is liberated, and the data are used to evaluate mineral behavior during mineral beneficiation. The liberation data for minerals in a suite of mill products from a circuit are processed by a materials balancing technique to calculate recoveries of minerals in different types of particles throughout the circuit. The liberation-materials balance data define mineral recoveries; define the behavior of an ore in a concentrator, pilot plant or bench test: and indicate whether recovery improvements are possible and/or feasible.

Jan 1, 1992

By J. P. Hoffman

In 1988 the Japan Iron and Steel Federation started a research-and-development programme known as DIOS (direct iron-ore smelting). Eight Japanese integrated steel producers and the Coal Mining Research Centre, subsidized by the Ministry of International Trade and Industry, are involved in the project. The aim of the programme is to have a 500 v/d pilot plant for the production of iron via an oxygen-coal in-bath smelting converter in operation by mid 1993. The three main components of the DIOS process are as follows: ?a fluidized bed for the pre-reduction of iron-ore fumes ?in-bath smelting reduction in a converter ?off-gas reforming by the addition of coal fines. The main drive is to provide a smelting process that is more energy-effective, using coal instead of coke and/or electricity. The advantages claimed include inter alia ?direct use of fine iron ore ?direct use of non-coking coals-low coal consumption ?low capital expenditure-replaces costly coke ovens, agglomeration plants, and the blast furnace ?economical production on mini-plant scale ?less of an impact on the environment. This concept of 'direct steel has been carried over to the production of stainless steel direct from the ores, again bypassing such energy-intensive units as the submerged-arc furnace for the production of ferrochromium. A number of Japanese companies have indicated a certain amount of success. Several interacting elements are recognized that could have a productivity-limiting aspect. The possibility of the direct production of stainless steel from chromite is discussed briefly with reference to the Highveld of the eastern Transvaal as a possible site for such a plant

Jan 1, 1992

By Raphael G. Kazmann

The predicted warming of the earth's surface, presently the subject of much debate, controversy and legislation, is based on what is termed "the greenhouse effect." This is the result of the property of certain atmospheric gases. These gases allow the passage of radiant energy to the earth's surface and reflect back, to the earth, the infrared radiation given out by the heated surface. Physicists have computed that if there were no greenhouse effect the average temperature of the earth, now about 15° C (60T), would be close to -18° C (OT). Just what gases have produced this salubrious effect? Water vapor is the most important. Then come carbon dioxide, methane and a number of minor constituents of the atmosphere, both natural and man-made. Climate change, its cause and its impact on human activities have been the subject of scientific and historical study for more than a century. Recently, some scientists have concluded that if the man-made increase in the carbon dioxide and other greenhouse gases continues, by the late 21st century the earth's global average temperature will rise between 2° to 8° F. This temperature rise would cause the water in the oceans to expand and the massive polar glaciers to melt. In 1980, it was predicted that the sea level would rise 7.6 m (25 ft) by the late 21st century. By 1985, the predicted rise was 1 m (3 ft); and by 1989, it was 0.3 m (1 ft) (Jastrow, Nierenberg and Seitz, 1990). Agricultural scientists have pointed out that an increase in atmospheric carbon dioxide would enhance biological growth including the production of foodstuffs.

Jan 1, 1992

By P. Bevilacqua, G. Ferrara, U. Preti

In the last decade, Meloy developed the IAC - Interfacial Area Conservation - model of liberation. His work included three conservation laws and a mathematical tool called textural transform. This paper reviews the developments and applications of the IAC model. From simple spherical two-phase locked particles with planar interfaces, the model has been developed for curved interfaces and solids with complex textures. Moreover, complex shaped particles and ores having more than two phases have been considered. The model equations give the degree of liberation of the component phases for different ore textures – platy blocky and acicular - as well as for different sue distributions. Lockedness profiles are offered for defining the middlings composition, so that from the model it is possible to predict washability curves.

Jan 1, 1992

By Jeffrey IC

This paper presents a method of measuring field power consumption of shearers and deriving specific energy consumption versus shearer haulage speed performance curves. A description of a computer program which simulates the cutting action of a shearer drum is presented. A comparison between the field specific energy curves and the computer simulation results is made. The simulation results compare well with the field data where all the coal seam is being cut by the shearer. The computer simulation results give back-calculated field pick force cutting characteristics, which allow the performance of the shearer to be predicted for other operating conditions, e.g. effect of changes to pick lacing, effect of changing the drum rotational speed, allows the calculation of power requirements for a particular production rate.

Jan 1, 1992