Search Documents

By Peter Kos

Since advances in the understanding of gravity thickening reflects the development of knowledge about suspensions themselves, the paper starts with the discussion of flocculent and nonflocculent suspensions. The properties of flocculent suspensions and their behavior in different concentration regions (zone settling, channelling, compression) are defined and discussed. In the main portion of the paper, the behavior of flocculent and nonflocculent suspensions during batch as well as continuous thickening, is presented, together with a brief review of the gravity thickening theories and sizing methods. The classical as well as the most recently developed methods are presented and their use and limitations are discussed.

Jan 1, 1980

By David D. Rabb

A report on location, sampling, assays, mineral examination, amenability leach tests, and evaluation of certain mine dumps in Mohave County, Arizona. Extractions of greater than 30 percent of the gold and silver were achieved during simulated heap leaching of selected mine dump material. Consumption of reagents was relatively low and results suggest leaching of prepared heaps is technically viable and could be economically attractive.

Jan 1, 1980

By S. P. Jekielek

"This paper describes the automation of a mine hoist ore loading pocket using a programmable controller. It provides an introduction to programmable control, and outlines the various modes and operating sequences of the loading pocket. A comparison is made with previous equipment to illustrate the increased flexibility, reliability and diagnostic functions that are gained.IntroductionLoading pockets have evolved from a couple of manually operated air cylinders to entirely automated systems. Early pockets were usually formed in rock, with loading and discharging regulated by air-operated gate s. Interlocks, added to this arrangement, prevented simultaneous operation of the gates and ensured proper hoist position . As the loading pocket advanced, it was recognized that gravity feed posed problems, often becoming plugged or letting water run through into the shaft. A belt conveyor was employed, eliminating the se problems and resulting in greater loading control. Weighing the combination of transistorized logic modules, replaced many relay systems. This elimination of moving parts and contacts increased reliability and reduced maintenance costs.As semiconductor technology progressed, there were major breakthroughs in miniaturization and reliability, and as a result the programmable controller was introduced. Programmable controllers first appeared in the automotive industry in the late 1960's. A system controller was required to replace the large relay panels in operation at that time. The use of digital integrated circuitry enabled these programmable controllers to automate processes with hundreds of inputs and outputs. Advances in electronics reduced production costs , making controllers for smaller application s viable . This development is on-going, each generation introducing controllers with greater capabilities for a wider variety of systems. equipment was the next step in loading pocket development, and dependance on much of the manual control was reduced . The complete system was first automated using relay panels. Solid- state devices were later introduced, and static control,"

Jan 1, 1980

By M. H. Moys

The capacity of grinding mills can be maximized by use of measurements of mill power and bearing pressures. The criterion is as follows. If the derivatives with respect to time of the power and bearing pressure signals have the same sign, the volume of the mill load is smaller than the optimum value; if they have different signs, the volume of the mill load is greater than the optimum value. Few attempts have been made to use measurements of bearing pressure in the estimation of absolute values for the parameters that define the state of the mill load (e.g, mass, volume, and dynamic angle of repose) because the bearing-pressure signal is a complex function of these and other parameters. This paper gives a mathematical model that relates bearing pressures to these parameters. The theoretical values obtained from this model are compared with experimental values, and it is concluded that the model constitutes a good description of experimental reality. If accurate measurements of the load supported by each bearing are available, the model can be used in the estimation of the mass of the load in the mill. If independent estimates of the volume of the load or the dynamic angle of repose are available, the other parameter can be estimated from measurements of the bearing loads.

Jan 1, 1980

By G. B. Misra

Though installations of main mine fans vary widely, the commonest installation is of a surface exhaust fan connected to an upcast shaft some distance below its collar by a horizontal fan drift bending sharply. downwards near its junction with the shaft. The junction of the fan drift with the shaft often causes considerable shock pressure loss if not properly designed. In one of the major coal mines in India circulating 180 m3/s of air through the mine a pressure drop of 229 Pa out of the total fan pressure of 568 Pa occurred at this junction while in a smaller gold mine circulating 9.4 m3/s it was 147 Pa out of a fan-drift pressure of 382 Pa. With larger mines circulating larger volumes of air, ill designed fan drifts can lead to considerable wastage of the power of ventilation. Shock loss at the junction of fan drifts with exhaust shafts depends on (1) the angle of deflection of the bend, (2) sharpness of the corners (both inner and outer) at the junction, (3) the degree of contraction of the flow-stream which depends on the cross- sectional area ratio of the shaft and the fan drift as well as the amount of leakage through the shaft collar. It must be noted here that the friction pressure loss in the bend is negligible compared to the shock pressure loss.

Jan 1, 1980

By J. Aiello

"A brief history of previous mining activity on Coal Mountain, near Corbin, British Columbia, is followed by a description of the steps leading up to the resumption of mining in /974 by Byron Creek Collieries. New developments, including a preparation plant, a rail spur and a totally enclosed facility, as well as operating techniques, are also discussed. IntroductionThe Corbin Mine of Byron Creek Collieries Limited is located in southeastern British Columbia, approximately 110 air miles southwest of Calgary (Fig. I), 15 miles south of Highway 3 via a newly constructed provincial road (Fig. 2). Development of the area began on July 30, 1905, when D.C. Corbin, a prominent businessman from the northwestern U.S., and his associate E.J . Robert s, first visited the site of Coal Mountain on horseback. Coal was in great demand by railways and other industrial users, so the Corbin Coal and Coke Co. , after acquiring 15,000 acres of land in the area , began to develop a mine.F.J. Roberts was responsible for the construction of the 14-mile rail spur, the Eastern British Columbia Railway, which joined the mine to the CPR main line at the McGillivray Loop. Rail access to the mine and its developing community, Corbin, B.C., was completed in September 1908, the same year that the first underground mine began production.The Corbin Coal and Coke Co. operated six mines on Coal Mountain (Fig. 3), and production from 1908 to 1930 inclusive totalled 2,337,800 tons. This production was allocated to the mines as shown in Table 1. No.3, 4 and 6 mines were operated intermittently from 1931 to 1935."

Jan 1, 1980

By George F. Learning

TOTAL DIRECT IMPACT The uranium mining industry's principal economic impacts on the Texas economy are the result of three flows of money from the industry into the remainder of the state's economy. These three are: (1) money paid to individuals (personal income) ; (2) money paid to other businesses (business income); and (3) money paid to state and local governments (government revenues). As these direct payments from the uranium industry to various other sectors of the Texas economy subsequently circulate and recirculate within the state, the indirect effects of uranium mining's direct impacts multiply to reach amounts significantly higher than the direct income flows alone. Over the past decade, the uranium mining industry has substantially increased its role as a provider of jobs, personal income, business income, and government revenues in Texas. The growth has come almost exclusively in a largely rural, seven-county area that lies within the triangle formed by the Laredo, San Antonio, and Corpus Christi metropolitan areas. The uranium mining industry, in fact, has been the major dynamic element in this rural area despite relative stagnation in most of the region's other basic economic sectors. Over the three years from 1976 to 1978, the South Texas uranium mining industry directly contributed a total of $115 million to the economy of the seven- county region in which it operated and $164 million to the economy of the entire state of Texas. In 1979 alone, the total direct contribution of the industry to the Texas economy had climbed to $124 million in personal, business, and government income. PERSONAL INCOME IMPACT In the period from 1976 through 1978, the South Texas uranium mining industry provided an average of $12.5 million in personal income each year directly to residents of Atascosa, Bee, Duval , Karnes, Live Oak, McMullen, and Webb counties -- the seven Texas' counties that make up the South Texas Uranium Belt. A1 though 84 percent of this resulted from the employment of area residents in uranium industry jobs, some amounts were also provided by the payment of rents and royalties to land owners for the use of their land and mineral rights in uranium mining operations. In 1979, the uranium industry provided approximately $38 million to residents of the Uranium Belt and the rest of Texas. This was more than double the average of $16.1 million provided to Texas residents during the 1976 to 1978 period. The full importance of the uranium industry as a source of personal income, however, should not be reckoned merely by the amount of wages and salaries that it pays directly to its own employees, nor by its rent and royalty payments paid directly to land and mineral rights owners living in Texas. The added payments that the industry makes directly to other Texas businesses and state and local governments in Texas are themselves converted into personal income as those business firms and government units in turn pay their employees. All of the direct income payments made by the uranium industry circulate and recirculate within the state's economy, multiplying their impact as they go, until they eventually all leak out of the state as federal taxes or as payments to individuals or businesses located outside of Texas. The combined circulation and recirculation of the direct personal, business, and government income that was provided by the-uranium industry in Texas during 1976, 1977, and 1978 resulted in an average annual amount of indirect personal income of more than $83 mill ion. This alone was $20 mill ion more than the industry's average annual sales during the same years. The total of combined direct and indirect personal income contributed to the Texas economy by the uranium mining industry in that same three-year period thus averaged almost $100 million annually. In 1979, the amount of indirect personal income contributed to the Texas economy by the circulation of uranium mining's direct contributions had risen to about $196 million, more than double the average of the previous three years. The combined direct and in- direct personal income impact in 1979 thus amounted to $234 million. BUSINESS INCOME IMPACT The income provided directly to other Texas business firms through the purchase of needed goods and services by the uranium industry has been twice as big as the industry's payrolls. In 1976, 1977, and 1978, the South Texas uranium industry spent an average of almost $36 million each year to buy both goods and services from other Texas businesses. By 1979, this direct contribution to the Texas economy had swollen to $76 million. The biggest share of the uranium industry's payments to other businesses have gone to contracting firms, including both construction firms and those providing specialized mining services. In the past four years, about 40 percent of the direct payments made by Texas uranium producers to other Texas firms have been to contractors. Texas wholesale and retail firms have also shared in the business sales provided by the South Texas uranium mining industry. Over the past four years, Texas wholesale and retail trade businesses have accounted for about 34 percent of the uranium mining industry's purchases from other Texas businesses. Public utilities firms have received another six per- cent, while Texas manufacturers and transportation firms have accounted for about five percent each. The other sectors of the state's economy, including other mineral industries, agriculture, finance, insurance, real estate, and services, have accounted

Jan 1, 1980

Future metal prices play a direct role in both the economic evaluation and short to medium planning of a mine scheduling sequence. It is difficult to predict with accuracy the future price of volatile metal commodities, however, it is possible to fix some future metal price, outside of long term contracts by the selling of futures contracts through a commodities exchange. The futures contract represents a fixed amount of a specified quality of a commodity for future delivery at a predetermined price. Several different types of hedging are possible, one in particular which is best suited for mining companies. There are relative advantages and disadvantages when trading in futures contracts and particular reference is made to gold contracts on the Sydney Futures Exchange.

Jan 1, 1980

By Fulvio V. Fonseca

The Trombetas bauxite deposits were discovered by ALLAN, as from the original work of the geologists Drs. E. E. GREIG and 3.A. STAARGAARD on the axis of the Amazon river, between Manaus and Santarem - (see fig. 1). With research licences obtained in 1965 by the SANTA RITA BAUXITA - a subsidiary of ALAN a group of Brazilian geologists, under the supervision of IGOR MOUSASTICOUSHVILLY, begins researches on the areas of Parintins, Juruti and Mathias with unsatisfactory results. In 1966, photographs obtained from the US Air Force and the Brazilian Oil Company PETROBRAS -, covering an Amazon region between Parintins, Santarem and north of Trombetas river, permitted the identification of a great number of plateaux between the Nhamunda and the Trombetas rivers. Based on this information, a research group has worked intensively from 1966 to 1967 allowing the discovery of the trihydrated bauxite in a quite large area. After five years of intense work and analysis of approximately 56.000 samples, near 500 million of tonnes of bauxite are evaluated on the several plateaux of the, area, thus insuring the commercial exploration of these deposits. Such discovery places Brazil among the detainers of the main bauxite stocks of the world and as a potential exporter.

Jan 1, 1980

By A F. Wilson

The use of stable isotopic measurements as a technique for elucidating the origin and history of the water in hydrothermal fluids is relatively new. Recent studies have emphasised the importance of meteoric water in the formation of many hydrothermal ore deposits including many epithermal gold-base metal deposits which occur in faulted volcanic terrane. Other vein-type gold ores are believed to have formed from fluids of magmatic or metamorphic origin and exhibit characteristic d180 values. These values also give information regarding temperatures and the degree of equilibrium. Preliminary oxygen data for some important gold deposits of eastern Australia are evaluated in the context of styles of mineralisation.

Jan 1, 1980

By Donald R. Williamson

Ore estimation at Cyprus Pima mine begins with estimating average copper grades for mine model blocks. Accuracy of the estimates has been checked four times in the last several years by comparing the estimates with arithmetic averages of corresponding blasthole (BH) assays. The data file now contains 3.567 estimated blockgrades and more than 10,000 blasthole assays. These data were compared by straight-line regression analysis at appropriate intervals as the body of data grew. Arithmetic averages of the estimates differed each time from arithmetic averages of the BH averages by nearly the same amount. More significantly, regression curves of the new total sets of data did not change position appreciably showing that copper grade estimates of blocks in all grade ranges from the lowest to the highest grade ores remained in error by nearly the same amount. Other studies revealed that core hole assays of the dominant ore type are biased and that that bias almost equals the error in estimation. Discovery of constancy in error indicated that regression analysis could be a means for correcting estimates of average block copper grades. A correction for estimated block grades was developed. It required determining which regression is appropriate for the particular problem, and a mechanism that is demonstrably sound. This paper describes the problem and the solution: No comparable study has been, found in the literature. Two other applications of regression analysis to metal grade comparisons are presented. Each adds a bit of support to a generalization which was suggested by correction of average block copper grades, namely, when performance of an estimate is to be evaluated, the variable taken to be the yardstick for the performance should be regressed on the estimate.

Jan 1, 1980

By S. P. Goplen, M. Henriksen, T. F. Barron

In the past decade, numerous large scale drilling projects have made use of reverse circulation air lift methods. Reverse air lift pumping can be established by injecting gas into a column of liquid; the subsequently decreased density of the gas-liquid mixture allows atmospheric pressure outside the lift conduit to establish flow. The rate of flow can be controlled by varying the gas to liquid ratio. A typical reverse circulation air lift system is depicted in [Fig. 1]. Allen 1 has described a number of reverse air lift drilling projects. Although cited examples are generally related to large diameter holes, the method has seen use in other applications such as sand dredging, chemical pumping, water well pumping. and continuous coring. One particular benefit obtained with enclosed reverse circulation drilling is elimination of lost circulation. The required air/water ratio for pumping at a given submergence and lift has been established experimentally by Gibbs.2 His data, however, do not reflect sensitivity of flow rate to air/water ratio. Further, in Gibbs' work, air apparently is injec-

Jan 1, 1980

A study is presented of the theoretically possible initiation systems for outbursts and the subsequent propagation mechanism.Previous occurrences of outbursts and their correlation to the theoretical system are described. An estimation of the energy release from two energy sources, gas strain energy and rock/coal strain energy, is presented and the relative importance of each source in the severity of outbursts. Summary: The description of mechanisms of outbursting follows the examination of these phenomena at Collinsville in Bowen No. 2 mine and at Leichhardt Colliery, Blackwater. Quantitative material contained in the paper refers to Leichhardt Colliery, Blackwater. Clearly from the work carried out to date gas release has a major part to play in the out- bursting at both of these collieries. In the case of the December 1 1978 outburst at Leichhardt Colliery energy release estimates place gas strain energy release contributing eight times the energy of that from rock/coal strain energy. Even the normal outbursts at Leichhardt Colliery appear to show this trend. Estimates of energy released are for comparative purposes between gas and rock strain energy and the values obtained may be regarded as approximate.

Jan 1, 1980

By E. J. Miller

The Ventilation Branch is engaged in a project to determine if low level carbon monoxide monitors used for early detection and warning of fire in a coal mine conveyor belt entry can provide protection equivalent to that of thermally actuated point type heat sensors commonly used for fire detection. A series of tests were conducted to determine the required operating parameters, such as sensor spacing and alarm levels of detected carbon monoxide to provide equivalency between' these methods of fire detection. This report summarizes the results of these tests.

Jan 1, 1980

By H. R. Beard

The Bureau of Mines investigated the absorption of radium and thorium from waste uranium leach liquor by clays and other materials. This work was conducted in support of the Bureau's goal of minimizing the environmental conflicts, impacts, and occupational hazards associated with mining and milling operations. Tailing and soil samples from New Mexico were evaluated for their potential to absorb radium and thorium from tailing liquors. Absorption ranged from 0 to 97 pct for radium and 0 to 60 pct for thorium. Some samples that readily absorbed radium were contacted with various salt solutions that could be present in tailing solutions to determine whether desorption would be a potential problem. The desorption of radium ranged from 0 to 75 pct. An alpha spectrometric method was used to determine the radium and thorium concentrations in the solutions and solids.

Jan 1, 1980

The Bureau of Mines, U.S. Department of the Interior, devised a flotation technique for upgrading chromite in chromium ores and gravity concentrates. The technique consisted of cationic flotation of chromite from a slime-free pulp acidified to pH 2.5 or lower using H2S04 modifier. Flotation results showed that ore containing serpentine as the primary gangue mineral was more amenable to concentration by this technique than ore containing the readily floatable olivine as the primary gangue mineral. Rougher flotation of a chromite ore containing abundant serpertine increased the grade form 19 to 41 percent Cra03 at a chromite recovery of 89.6 percent. Rougher flotation of ore containing abundant olivine upgraded the chromite from 23.4 to 29.6 percent Cr203 at a recovery of 89.4 percent. The technique was also applied to chromite gravity concentrates to further upgrade chromite and to reject silicates. Flotation of a gravity concentrate containing 40.9 percent Cr203 and 4.4 percent SiO2 recovered 90 percent of the chromite in cleaner products containing 44.9 percent Cr203 and 0.63 percent Si02. The combined recovery by gravity and flotation was 87 percent. An economic evaluation of this technique will be undertaken to deter-mine its feasibility for commercial use.

Jan 1, 1980

By R. T. Webber, D. Moffett, D. W. Averill, G. H. Kassakhian

INTRODUCTION In Canada, radium-226 is removed from uranium mining and milling effluents by the addition of barium chloride to precipitate barium-radium sulphate. Large settling ponds are provided to effect solid-liquid separation. However, the barium-radium sulphate precipitate [(Ba,Ra)S04] is a fine, slow-settling crystalline solid which is not easily removed by simple sedimentation systems. Consequently, settling pond effluents may contain appreciable quantities of particulate or suspended radium-226, depending upon the specific pond system and/or the time of year considered. Also, current technology is expected to be incompatible with ultimate disposal goals since safe recovery of the barium-radium sulphate sludge from the settling ponds may be difficult to achieve (IAEA, 1976). Under the auspices of Environment Canada, a Government-Industry Mining Task Force established a Radioactivity Sub-Group in 1974 to assist in the development of effluent regulations and guidelines for the uranium mining industry. Among the recommendations of the Sub-Group was the need to seek more effective methods of radium removal, including development of physical--chemical treatment systems as an alternative to settling ponds. In response to the Sub-Group recommendations, a bench scale feasibility study began in March 1976 at the Wastewater Technology Centre (WTC) of Environment Canada. The bench scale work was expanded and accelerated in 1977 with financial assistance provided by the Atomic Energy Control Board. The results of this study indicated that coagulation and flocculation of the (Ba,Ra)S04 precipitate greatly increased settling rates (Wilkinson and Cohen, 1977). Subsequently, a research program with a larger scope was initiated in January 1978; this program is jointly managed and funded by government and industry as indicated in Table 1. The principal goal of the Joint Government-Industry Program is the development of a physical-chemical process to reduce the radium-226 content of uranium mining and milling effluents. The following effluent radium-226 activities were established as targets for the program: 0.37 Bq/L (10 pCi/L) as total radium-226; 0.11 Bq/L (3 pCi/L) as dissolved radium-226. Process development work was undertaken at bench scale at the WTC and at

Jan 1, 1980

Mining and metals projects have tended to increase in both scope and cost to a point where many projects are Droperly designated as superprojects. Specialist engineer- constructors have developed organisations and systems to provide project management services during the design and construct phase of large projects. However, the engineer-constructor is also required to provide a wide spectrum of services during the evolution of large projects prior to the construction phase. Some common phases of pre-construction evolution are identified together with the associated types of specialised services which may be required. A project management team approach is described which has been developed for the design and construct phase. It is suggested that a modified matrix organisation could be adapted to the provision of special- ised services as well as to project management for ore-construction phases of the project.

Jan 1, 1980

By Paul H. Rydlund

The wide use of bulk ANFO in surface coal mines is questionable in our energy conscious environment. At many locations, bulk ANFO is not the proper economic selection. Water conditions, energy requirements, waste and spillage, and vibration control are factors too often overlooked in the proper choice of blasting agents. Cost savings over 20% have been realized by converting bulk ANFO to packaged blasting agents. Future trends suggest greater concern for energy conservation in blasting will limit bulk ANFO applications and promote packaged products where quality can be maximized, waste and spillage eliminated, and water compatibility in wet areas assured.

Jan 1, 1980

By D. Pearson

About 15,000 tonnes of zinc per year is present in the dusts and fumes produced in electric arc and BOS steelmaking, secondary copper refining and brass ingot making. Apart from the use of some copper-smelter fumes for zinc chemicals manufacture, zinc is not recovered and their disposal by landfill entails some risk of pollution by leach-out. The paper describes processes for recovering the zinc based on leaching and electrowinning. It was shown that the procedures normally employed for purifying zinc-electrolytes derived from primary sources are sometimes ineffective for secondary materials. Alternative process routes are proposed. Source materials were leached with acidic or alkaline reagents and solvent extraction was employed for electrolyte purification in addition to the usual techniques involving precipitation. Examples of integrated flow sheets for specific source materials are presented.

Jan 1, 1980